Wilson Electronics 824WV Mobile Wireless Single Band Amplifier User Manual

Download:
Mirror Download [FCC.gov]
Document ID	731438
Application ID	YYUEUfU0SIYkc498M65yqg==
Document Description	Users Manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	78kB (974939 bits)
Date Submitted	2006-11-22 00:00:00
Date Available	2006-11-29 00:00:00
Creation Date	2006-11-10 16:07:53
Producing Software	Adobe PDF Library 7.0
Document Lastmod	2006-11-10 16:23:49
Document Title	Users Manual
Document Creator	Adobe InDesign CS2 (4.0.4)

Amplifier
Installation
Guide
Mobile Wireless
Single Band
Cellular
Amplifier
PART/MODEL# 801101
Contents:
Guarantee and Warranty · · · · · · · · · · · · · · · · · · · · · · · · 1
How it Works · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · 2
Before Getting Started · · · · · · · · · · · · · · · · · · · · · · · · · · 3
Installing a Wilson Outside Antenna · · · · · · · · · · · · · · · 4
Installing a Wilson Amplifier · · · · · · · · · · · · · · · · · · · · · · 5
Installing a Wilson Inside Antenna (Wireless) · · · · · · · · 6
Installing a Wilson Inside Antenna (Attached) · · · · · · · · 7
Powering Up a Wilson Amplifier · · · · · · · · · · · · · · · · · · · 8
Warnings and Recommendations · · · · · · · · · · · · · · · · · 9
Understanding the Amplifier Lights · · · · · · · · · ·· · · · · · · 10
Amplifier Specifications · · · · · · · · · · · · · · · · · · Back Cover
Warning: This manual contains
important safety and operating information.
Please read and follow the instructions
in this manual. Failure to do so could be
hazardous and result in damage to your
amplifier.
Wilson
®
Electronics, Inc.
30-Day Money-Back Guarantee
All Wilson Electronics products are protected by Wilson’s 30-day money-back
guarantee. If for any reason the performance of any product is not acceptable,
simply return the product directly to the reseller with a dated proof of purchase.
1-Year Warranty
Wilson Electronics amplifiers are warranted for one (1) year against defects in
workmanship and / or materials. Warranty cases may be resolved by returning the
product directly to the reseller with a dated proof of purchase.
Amplifiers may also be returned directly to the manufacturer at the consumer’s
expense, with a dated proof of purchase and a Returned Material Authorization
(RMA) number supplied by Wilson Electronics. Wilson shall, at its option, either
repair or replace the product. Wilson Electronics will pay for delivery of the repaired
or replaced product back to the original consumer.
This warranty does not apply to any amplifiers determined by Wilson Electronics
to have been subjected to misuse, abuse, neglect, or mishandling that alters or
damages physical or electronic properties.
RMA numbers may be obtained by phoning Technical Support at 866-294-1660.
Operation is subject to the following two conditions: (1) This device may not cause
interference, and (2) this device must accept any interference, including interference that
may cause undesired operation of this device.
Disclaimer: The information provided by Wilson Electronics, Inc. is believed to
be complete and accurate. However, no responsibility is assumed by Wilson
Electronics, Inc. for any business or personal losses arising from its use, or for
any infringements of patents or other rights of third parties that may result from
its use.
Copyright © 2006 Wilson Electronics, Inc. All rights reserved.
Installation Instructions for the Following Wilson Amplifiers:
Mobile Wireless Single Band Amplifier
Model #801101
FCC ID: PWO824W V
IC: 4726A-824W V
The term “IC” before the radio certification number only signifies that
Industry Canada technical specifications were met.
Inside this Package
Wireless
amplifier
DC plug-in
power cable
6‘ extension
cable
How it Works
Low-profile
antenna
(Option A - see p. 6)
Universal
connector
(Option B - see p. 7)
Your new Wilson amplifier has been carefully engineered to significantly improve the
performance of your cell phone or cellular data card in mobile applications. Together with
an outside antenna (sold separately), the amplifier’s state-of-the-art technology is designed
to increase your signal up to 10 times, reduce disconnects and dropouts, and increase data
communication rates needed for 3G technologies.
The outside antenna will collect the cell tower signal and send it through the cable to the
amplifier. The signal is then boosted and sent through the extension cable to the inside
antenna or to the universal connector, depending on your application. Your cell phone or
data card then communicates with the improved signal. When the cell phone or data card
transmits, the signal goes through the inside antenna or the universal connector and the
extension cable, is boosted by the amplifier and broadcast back to the cell tower through the
outside antenna.
Wilson Electronics manufactures a wide variety of antennas to help you customize your
amplifier for your specific application. Several are shown below. See your dealer or visit
www.wilsonelectronics.com.
NOTE: Use of this amplifier with an
antenna gain higher than 5.12 dBi
is in violation of FCC regulations
for which the offender is fully
liable. All Wilson mobile
antennas are 5.12 dBi or less
in the 800 MHz band.
Mini
Magnet
Magnet
Mount
Trucker
Mount
Marine
Antenna
NMO
Mount
Before Getting Started
This guide will help you properly install Wilson’s single-band, mobile wireless amplifier. It is
important to read through all of the installation steps for your particular application
prior to installing any equipment. Read through the instructions, visualize where all the
equipment will need to be installed and do a soft installation before mounting any equipment.
If you do not understand the instructions in full, seek professional help, or contact Wilson
Technical Support at 866-294-1660.
Installation Diagram
Inside Antenna
Outside
Antenna
Warning: In a wireless installation,
do not plug the amplifier directly into the
cell phone or data card using an antenna
adapter. It will damage the amplifier.
Cell Phone
PDA
Notebook
Inside
Antenna
DC Power
Supply
Amplifier
Installation Diagram
Universal Connector
Outside
Antenna
Warning: In a wireless installation,
do not plug the amplifier directly into the
cell phone or data card using an antenna
adapter. It will damage the amplifier.
Cell Phone, PDA or
Notebook with
universal connector
attached
DC Power
Supply
Amplifier
Installing a Wilson Outside Antenna
To receive the best cell signal, select a location in the center of the vehicle’s roof at least
12 inches away from any other antennas and free of obstructions.
Follow the specific antenna installation instructions included with the outside antenna
(sold separately).
Warning: The outside antenna must
be installed with a separation of at least 20
inches from any of the vehicle’s occupants or
nearby persons and must not be located or
operating in conjuction with any other antenna
or amplifier.
Warning: Do not use any type of glassmount antenna with this amplifier. The outside
and inside antennas must be shielded from
each other to prevent oscillation.
The outside antenna must be installed
vertically. Signal performance will be
degraded if the antenna is not vertical.
Optional MagnetMount Antenna
Shown
Part #301103
Carefully
Pull Down
Door Seal
Run Cable
Under
Seal
The antenna cable may be run through the
door to the amplifier.
For a more professional-looking installation,
the antenna cable may be run under the
door seal. Carefully pull down the door
seal. Run the cable through the seal
and push the seal back into place. This
prevents constant wear and tear on the
cable as the door opens and closes.
The antenna cable is small enough to easily
tuck under the door seal or plastic molding.
Tuck Cable
Under Seal
Installing a Wilson Amplifier
Warning: Do not plug in the DC power
supply until the outside and inside antenna
cables are attached to the amplifier.
Select a location to install the amplifier that
is away from excessive heat, direct sunlight
or moisture and that has proper ventilation.
Recommended installation locations are:
• Under the seat
• In the trunk
• Under the dash
Run the cable from the outside antenna and
attach it to the FME-Male connector labeled
“outside antenna” on the amplifier.
Attach the inside antenna cable to the FMEMale connector labeled “inside antenna” on
the amplifier.
Wilson offers two options of improved signal
inside a vehicle:
Option A (Wireless) - offers the
convenience of no physical connection to
the cell phone or cellular data card.
Option B (Attached) - places the universal
connector directly on the cell phone or
cellular data card for maximum signal
performance.
Option A (Wireless)
Installing a Wilson Inside Antenna
Low-profile
Antenna
Amplifier
Install the low-profile inside antenna 8-12
inches from where the cell phone or cellular
data card will be used.
Warning: Do not install the low-profile
antenna within four inches of metal. (Metal
found inside the vehicle’s seat will not affect
the antenna’s performance.)
Place the inside antenna on the side of the
driver’s seat for maximum performance.
Install the inside antenna at least eight
inches, but not more than 12 inches, from
where the cell phone or cellular data card
will be used.
Install the inside antenna at the same angle
as the cell phone when held in use, or place
next to the laptop’s cellular data card. This
will maximize the signal strength.
For a more professional-looking installation,
the low-profile antenna may be slid under
the seat cover or leather, high on the
driver’s seat.
Warning: The inside antenna must
be installed with a separation of at least
eight inches from all persons and must not
be located in conjunction with any other
antenna or amplifier.
Option B (Attached)
Installing a Wilson Universal Connector
Amplifier
6’ Extension
Cable
Universal
Connector
The universal connector must be placed
directly on the cell phone or cellular data
card to work properly. Attach the universal
connector to the cell phone or cellular data
card with the VELCRO® included in the
package.
The universal connector and extension
cable included in the package are long
enough to reach the amplifier location. This
allows for ease and convenience of use.
To adjust the universal connector for the
best signal, go to a weak signal location
where your cell phone registers only 12 bars without the universal connector
connected. Then, attach the universal
connector to the phone and you should see
a signal improvement of 2 or more bars.
NOTE: Many phones take up to 20 seconds
to reset the bar indicator.
Cellular data card
To maximize performance, attach the
universal connector as close as possible to
the original antenna on your cell phone or
cellular data card.
For cell phones with an internal antenna,
place the universal connector on the back,
upper left-hand corner of the phone. (Figure
1) NOTE: Certain phones, such as the
Motorola RAZR, have internal antennas at
the base, rather than the top, in which case
the universal connector should be attached
at the bottom rear of the phone.
For cell phones with an external antenna,
place the universal connector directly below
the phone’s original antenna. (Figure 2)
If you have any questions as to the location
of the antenna on your phone, call Wilson
Technical Support at 866-294-1660 or visit
www.wilsonelectronics.com.
Figure 1
Figure 2
To Amplifier
Powering up a Wilson Amplifier
Make sure both the outside and inside
antenna cables are connected before
powering up the amplifier.
Connect the DC plug-in power supply
cable to the amplifier marked “Power” and
insert the large end into DC power socket
(the cigarette lighter outlet.)
Carefully insert the power cable.
Warning: Use only the power
supply cable provided in this package.
The power supply must be 12 V DC.
The amplifier may remain on all the time.
However, leaving the amplifier on in a
vehicle when it is not running can discharge
the battery in a day or two.
IMPORTANT: Do not power up the amplifier unless antenna cables are attached to
amplifier.
A good option is to power the amplifier
through the ignition switch so the amplifier
is turned on and off with the vehicle.
NOTE: The aluminum casing of a Wilson amplifier will adjust very quickly to the ambient
temperature of its environment. For example, in the summer, when the inside of a car can
reach 140 degrees Fahrenheit, the amplifier temperature may be 150 degrees or higher.
The casing will be hot to the touch, similar to a metal door handle or a steering wheel. Such
high temperatures will not damage the amplifier, nor do they pose a fire risk to the vehicle.
As recommended in these instructions, install the amplifier in a location with adequate
ventilation, such as under the seat, in the trunk or under the dashboard. Keep the area free
of items that could block air flow to the amplifier.
Separation of inside and outside antennas is very important. The metal roof of the vehicle
acts as a barrier and helps shield the two antennas from each other, preventing oscillation.
If the vehicle has a sunroof, it is important to separate the inside and outside antennas by at least
five feet. This prevents the amplifier from overloading or oscillating.
Distance between antennas
through a sunroof must be
5 feet or more.
Warnings and Recommendations
Warning:
In a wireless installation, do not plug the amplifier directly into
the cell phone or cellular data card using an antenna adapter. It
will damage the cell phone or cellular data card.
Warning:
Do not install the inside antenna within four inches of metal.
(Metal found inside the vehicle’s seat will not affect antenna
performance.)
Warning:
Do not use any type of glass-mount antenna with this amplifier.
The outside and inside antennas must be shielded from each
other to prevent oscillation.
Warning:
Do not plug in the DC power supply until the outside and inside
antenna cables are attached to the amplifier.
Warning:
RF Safety: The inside antenna must be installed with a
separation of at least eight inches from all persons and must not
be located in conjunction with any other antenna or amplifier.
Warning:
RF Safety: The outside antenna must be installed with a
separation of at least 20 inches from any of the vehicle’s
occupants or nearby persons and must not be located or
operating in conjunction with any other antenna or amplifier.
All roof-mount antennas should be centrally located on the
roof of the vehicle. Mirror-mount antennas should be at least
six inches from the ground and leave at least 20 inches of
separation from any persons near or around the vehicle. Use
of a cellular amplifier with an antenna gain higher than 5.12 dBi
is in violation of FCC regulations for which the offender is fully
liable. All Wilson mobile antennas are 5.12 dBi or less in the
800 MHz band.
Recommended amplifier installation locations are:
• Under the seat
• In the trunk
• Under the dash
Install the low-profile antenna 8-12 inches from where the cell phone or cellular
data card will be used.
Power the amplifier through the ignition switch so the amplifier is turned on and
off with the vehicle.
If the vehicle has a sunroof, it is important to separate the inside and outside
antennas by at least five feet. This prevents the amplifier from overloading or
oscillating.
Understanding the Amplifier Lights
Power Indicator Light
(located on the side)
Signal Indicator Light
(located on the back)
Power Indicator Light
Shows green when the unit is turned on.
Signal Indicator Light
A green light indicates normal operation.
An orange light indicates overload from the cell site. The amplifier has
temporarily shut down and will automatically reset.
A red light indicates that oscillation has been detected. The inside and
outside antennas are too close to one another. Increase the antenna
separation distance, then remove and replace the DC power cable to reset
the light. If it still shows red, repeat the procedure.
10
Amplifier Specifications
Single Band
800 MHz Specifications
801101
FME-Male
50 ohms
5.5 x 4.3 x 1.4 inch or 14 x 10.8 x 3.5 cm
1.32 lbs or 0.6 kg
824-894 MHz
Model Number
Connectors
Impedance (input/output)
Dimensions
Weight
Frequency
Passband Gain (nominal)
(uplink/downlink)
43 dB / 43 dB
(uplink/downlink)
50 MHz / 50 MHz
20 dB Bandwidth (nominal)
Power output for single cell phone (uplink)
CDMA
GSM
EDGE
AMPS
Power output (uplink) for multiple
cell phones:
Number of
cell phones
+33.3 dBm
+32.0 dBm
+31.5 dBm
+31.6 dBm
Maximum Power
+20.3 dBm
+16.8 dBm
+14.3 dBm
+12.3 dBm
+10.8 dBm
Power output for single received channel
(downlink)
CDMA
GSM
EDGE
AMPS
Power output for multiple received
channels (downlink). The maximum
power is reduced by the number of
channels:
+2.7 dBm
-5.2 dBm
-3.1 dBm
-5.0 dBm
Noise Figure (typical)
Isolation (uplink/downlink)
Power Requirements
Amplifier Usage
FCC ID:
IC:
Number of
channels
Maximum Power
-2.5 dBm
-6.0 dBm
-8.5 dBm
-10.5 dBm
-14.5 dBm
3 dB nominal
> 90 dB
12 V, .5 A - 1.5 A (subject to uplink power)
PWO824W V
4726A-824W V
Notes:
1. Nominal gain is the maximum gain at any frequency in the passband.
2. Nominal bandwidth is the difference between two frequencies that are adjacent to the passband where the amplification is 20 dB
lower than the passband amplification. One of the frequencies is lower than the passband and the other is higher.
3. The Manufacturer’s rated output power of this equipment is for single carrier operation. For situations when multiple carrier
signals are present, the rating would have to be reduced by 3.5 dB, especially where the output signal is re-radiated and can
cause interference to adjacent band users. This power reduction is to be by means of input power or gain reduction and not by
an attenuator at the output of the device.
4. The maximum power for 2 or more simultaneous signals will be reduced by 6 dB every time the number of signals is doubled.
5. The term “IC” before the radio certification number only signifies that Industry Canada technical specifications were met.
Phone: 866-294-1660
Wilson® Electronics, Inc.
www.wilsonelectronics.com Fax: 435-656-2432
AIG SBMW 018 / 11.09.06

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.4
Linearized                      : No
Page Count                      : 12
XMP Toolkit                     : XMP toolkit 2.9.1-13, framework 1.6
About                           : uuid:72963df2-b6a0-49ec-b6f6-64576eb58a5d
Producer                        : Adobe PDF Library 7.0
Trapped                         : False
Create Date                     : 2006:11:10 16:07:53-07:00
Modify Date                     : 2006:11:10 16:23:49-07:00
Metadata Date                   : 2006:11:10 16:23:49-07:00
Creator Tool                    : Adobe InDesign CS2 (4.0.4)
Thumbnail Format                : JPEG
Thumbnail Width                 : 256
Thumbnail Height                : 256
Thumbnail Image                 : (Binary data 8152 bytes, use -b option to extract)
Instance ID                     : uuid:0a74bd80-1f48-4fb6-ab66-be3c5b28d592
Rendition Class                 : proof:pdf
Document ID                     : adobe:docid:indd:38705609-6f85-11db-aef2-81be419c6968
Derived From Instance ID        : 38705605-6f85-11db-aef2-81be419c6968
Derived From Document ID        : adobe:docid:indd:38705602-6f85-11db-aef2-81be419c6968
Manifest Link Form              : ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream
Manifest Placed X Resolution    : 300.00, 72.00, 300.00, 72.00, 100.00, 72.00, 300.00, 300.00, 300.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 300.00, 300.00, 300.00, 100.00, 72.00, 72.00, 72.00, 300.00, 300.00
Manifest Placed Y Resolution    : 300.00, 72.00, 300.00, 72.00, 100.00, 72.00, 300.00, 300.00, 300.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 300.00, 300.00, 300.00, 100.00, 72.00, 72.00, 72.00, 300.00, 300.00
Manifest Placed Resolution Unit : Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches
Manifest Reference Instance ID  : uuid:38B8922C8D1DDB11B35EF878222AB3A8, uuid:6c5c9b94-5feb-4280-922c-a1b9371e2ea4, uuid:38B8922C8D1DDB11B35EF878222AB3A8, uuid:01819B773B22DB1185A8E804CE763B2E, uuid:664F8BF4A4D3DA1183388726EAF7737B, uuid:684F8BF4A4D3DA1183388726EAF7737B, uuid:1BEDA7E3D489DA118200A07DB41E56A2, uuid:7616D919729EDA11A6F7F17C2245A10B, uuid:B280E9DE4122DB11A758B4A0F489E959, uuid:aff2a6d3-f1ec-4772-a55e-ebd081b57875, uuid:4e41b806-6cad-4150-b3a1-0a8b89422bfa, uuid:4CA60D7BB820DB118D80C280DA78ECBE, uuid:50A60D7BB820DB118D80C280DA78ECBE, uuid:213F1D1FB121DB11B288933EBCE38D0B, uuid:233F1D1FB121DB11B288933EBCE38D0B, uuid:80062532AE21DB11B288933EBCE38D0B, uuid:0D62EEFDD11CDB118DDF9E972E7DEE7D, uuid:B280E9DE4122DB11A758B4A0F489E959, uuid:0D62EEFDD11CDB118DDF9E972E7DEE7D, uuid:664F8BF4A4D3DA1183388726EAF7737B, uuid:213F1D1FB121DB11B288933EBCE38D0B, uuid:961D4217500CDB11A42E994560F47B89, uuid:311cb791-bccf-4ff0-bc10-eb863efc69c6, uuid:38B8922C8D1DDB11B35EF878222AB3A8, uuid:530F908AD165DB11873CFD110C3FBA6C
Manifest Reference Document ID  : uuid:37B8922C8D1DDB11B35EF878222AB3A8, uuid:AE3C53E87800DB119EE1FCBF77AD56DD, uuid:37B8922C8D1DDB11B35EF878222AB3A8, uuid:1A6AE96CA2D3DA1183388726EAF7737B, uuid:654F8BF4A4D3DA1183388726EAF7737B, uuid:5E4F8BF4A4D3DA1183388726EAF7737B, adobe:docid:photoshop:e7c94402-7167-11d9-8b01-95a288864e59, uuid:7516D919729EDA11A6F7F17C2245A10B, uuid:B180E9DE4122DB11A758B4A0F489E959, uuid:D2CBE79D6564DB11973A835291636013, uuid:91CF5982BF5EDB11AA00986C3F30A8E4, uuid:4BA60D7BB820DB118D80C280DA78ECBE, uuid:4FA60D7BB820DB118D80C280DA78ECBE, uuid:6F8DABD6AD21DB11B288933EBCE38D0B, uuid:6E8DABD6AD21DB11B288933EBCE38D0B, uuid:6D8DABD6AD21DB11B288933EBCE38D0B, uuid:0C62EEFDD11CDB118DDF9E972E7DEE7D, uuid:B180E9DE4122DB11A758B4A0F489E959, uuid:0C62EEFDD11CDB118DDF9E972E7DEE7D, uuid:654F8BF4A4D3DA1183388726EAF7737B, uuid:6F8DABD6AD21DB11B288933EBCE38D0B, uuid:951D4217500CDB11A42E994560F47B89, uuid:7B4A3C65B4D3DA11AB80D7DBF7C3B238, uuid:37B8922C8D1DDB11B35EF878222AB3A8, uuid:19939DF1D265DB11BDBD80861BEBD0EE
Format                          : application/pdf
Creator                         : Adobe InDesign CS2 (4.0.4)

EXIF Metadata provided by EXIF.tools