Winegard WF4000 WiFi Extender Product User Manual WF 4000 Quickx

Download:
Mirror Download [FCC.gov]
Document ID	3082713
Application ID	ZKudzrxH2fpQsVrnLgL41w==
Document Description	Exhibit D Users Manual per 2 1033 b3
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	18.56kB (231976 bits)
Date Submitted	2016-08-01 00:00:00
Date Available	2016-08-01 00:00:00
Creation Date	2016-08-01 09:30:25
Producing Software	Acrobat Distiller 11.0 (Windows)
Document Lastmod	2016-08-01 09:30:25
Document Title	Microsoft Word - WF-4000 Quick.docx
Document Creator	PScript5.dll Version 5.2.2
Document Author:	decrowder

WF‐4000 Quick Start Guide:
Ensure that your device is powered on.
Connecting a device to the WF‐4000:
1. Scan for wireless networks with your device.
2. Select the Winegard Connect Network listed on the label on the back of the WF‐4000 shown
below after the Default SSID:
Once selected, the WF‐4000 will ask for a Password. Enter the Default Password on the back of the
WF‐4000
Now that the device is connected to the WF‐4000, open an internet browser and enter
10.11.12.1
into the address bar.
Log in using
1. User Name : admin
2. Password : admin
Scanning for available internet:
Navigate to home screen.
Select “Scan for available internet.”
The WF‐4000 will scan for available networks and display a list sorted by signal strength.
Select the desired network and click continue.
Enter the network password if needed. Some networks will display a “Splash Page” when connecting.
Once the WF‐4000 connects, open a fresh browser and the network will display this page.
Once “Internet Status” shows Connected to the chosen network, (this could take up as long as two
minutes) the system is ready to browse.
4G/LTE Set up:
To use the 4G connection click the bullet for 4G/LTE in the Internet Access section and click select. There
may be a three minute delay as the WF‐4000 connects. Once Internet Status shows “Connected” this set
up is complete.
FCC Statement
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful
interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment uses and can
radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to
try to correct the interference by one or more of the following methods:
 Reorient or relocate the receiving antenna.
 Increase the separation between the equipment and devices.
 Connect the equipment into an electrical outlet on a circuit different from that which the radio receiver is connected.
 Consult the dealer or an experienced radio/TV technician for help.
FCC Caution
Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate this
equipment.
Only channel 1~11 can be operated. Selection of other channels is not possible.
This device and its antenna(s) must not be co‐located or operation in conjunction with any other antenna or transmitter.
FCC Radiation Exposure Statement
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and
operated with minimum distance 25cm between the radiator and your body.
This device and its antenna(s) must not be co‐located or operating in conjunction with any other antenna or transmitter except in accordance
with FCC multi‐transmitter product procedures.

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.5
Linearized                      : Yes
Author                          : decrowder
Create Date                     : 2016:08:01 09:30:25-05:00
Modify Date                     : 2016:08:01 09:30:25-05:00
XMP Toolkit                     : Adobe XMP Core 5.4-c005 78.147326, 2012/08/23-13:03:03
Format                          : application/pdf
Creator                         : decrowder
Title                           : Microsoft Word - WF-4000 Quick.docx
Creator Tool                    : PScript5.dll Version 5.2.2
Producer                        : Acrobat Distiller 11.0 (Windows)
Document ID                     : uuid:b8f193f0-17aa-45b5-a2dd-14eb16d09438
Instance ID                     : uuid:25701aea-97c2-41e9-9f6d-faa41121de05
Page Count                      : 4

EXIF Metadata provided by EXIF.tools