Winplus BT30404F REAR VIEW SPAKERPHONE W/CALLER ID User Manual Yada manual R

Winplus Co., Ltd. REAR VIEW SPAKERPHONE W/CALLER ID Yada manual R

Users Manual

5. Caller ID DisplayNote: Caller ID Display is a network service; please consult your network provider for details.Caller ID can be displayed in 3 ways:a) By Name YD-V16 can display the caller’s name when receiving call. To display caller’s name, the name must be stored in the phone book.b) By Phone Number Phone number will be displayed if there is no record of that number in the phone bookc) Withheld Number When a caller withholds his number, WITHHELD will be displayedNote: The YD-V16 do not automatically save numbers dialed directly from your mobile phone and will not be displayed. 6. Call WaitingNote: Call Waiting is a network service, please consult your network provider for details.To accept an incoming call during a conversation:• Press the Send button and the phone will automatically switch to Line 2To switch calls between the two lines:• Press the Send button to switch between lines• Turn off the YD-V16 when not in use• Attach the YD-V16 carefully and firmly to your rearview mirror (Please refer to instructions on how to attach the YD-V16 to your rearview mirror)• Do not let the YD-V16 be in contact with liquid as it is not waterproof. Avoid putting it in places where there is excessive moisture and humidity.• Do not expose the YD-V16 to direct sunlight or place in areas with high temperature, as it may result in an explosion• If the YD-V16 is not in use for a prolonged period, store in a cool, dry place, free from moisture, humidity and dust• Do not use abrasive cleaning solvents to clean the YD-V16• Do not expose the YD-V16 to contact with sharp objects as this will cause scratching and damage• Do not stick anything inside the YD-V16 as this may damage internal components• Do not attempt to disassemble the YD-V16, as it does not contain serviceable components• Only use the manufacturer supplied charger when charging the YD-V16• Only charge the YD-V16’s built-in battery in accordance with the instructions of this user guideFor questions or issues regarding the product, please visit www.letsyada.com or contact Winplus in your area/region to speak to our customer service representative:Winplus USA Tel. 866-294-9244 Tel. 310-638-0588Winplus Europe Tel. 44-1440-713888Winplus Australia Tel. 61-3-9720-4143Winplus New Zealand Tel. 62-9-5254575Winplus Asia Tel. 852-2798-8932You can also contact us online by visiting www.winplus.com for more information about the product.IF YOU ARE EXPERIENCING ANY ISSUES WITH THE PRODUCT DURING OPERATION, DO NOT RETURN THE PRODUCT TO THE STORE. CONTACT WINPLUS DIRECTLY FOR INSTRUCTIONS ON HOW TO RETURN/EXCHANGE THE PRODUCT.• Do not disassemble the charger as it may expose you to dangerous voltages or other risks. Incorrect reassembly can cause electric shock when the YD-V16 is subsequently used• Do not use the charger outdoors or in damp areas• Avoid charging the YD-V16 in extremely high or low temperatures• It is recommended to charge the YD-V16 immediately whenever low battery power is encountered to prolong durability & standby timeIf you are unable to pair your mobile phone with the YD-V16:• Make sure the battery is fully charged• Turn off the YD-V16 and turn it on again• Turn off all other Bluetooth® devices before you start pairing • Ensure your mobile handset’s Bluetooth® feature is activated. Please refer to your mobile handset user guide for specific instructions• Repeat pairing procedures• Ensure the YD-V16 is within a maximum of 10 meters of your mobile handset(s) or Bluetooth® enabled device and there are no obstructions, such as wall or other electronic devices, in between as it may cause interference transmission• If all the above steps do not resolve your problem, please remove the battery for at least 20 minutesThe YD-V16 Rearview Mirror Speakerphone is compliant with and adopts the Bluetooth®Specification V1.2. However, interoperability between the device and other Bluetooth®-enabled products is not guaranteed because it depends on compatibility. For more information on the compatibility between the device and other Bluetooth®-enabled products, please contact Customer Service.If the LCD display hanged or all button functions disabled:• Use the RESET switch at the back of the unitWINPLUS NORTH AMERICALIMITED WARRANTYWINPLUS North America warrants, to the original purchaser, that its products are free from defects in material and workmanship for 90 days from the date of original purchase. Where permitted by law, WINPLUS North America’s liability shall be limited to that set forth in this limited express warranty. This limited express warranty shall be the exclusive remedy of the purchaser and WINPLUS North America makes no other warranty of any kind aside from the limited express warranty stated above. Note: Warranty only applies for North American customers or purchases made in the North America.YD-V16 User Manual www.letsyada.comThank you for purchasing the latest Yada wireless technology product from Winplus. We hope you will enjoy all features and benefits offered by the YD-V16 Bluetooth® Rearview Mirror Speakerphone. These features and benefits were designed with the goal of making wireless communication more convenient for the user. Winplus USA375 W. Apra St. Rancho Dominguez, CA 90220info@winplususa.comwww.winplususa.comWinplus EuropeUnit 4, Two Counties Estate, Falconer Road, Haverhill, Suffolk CB9 7XZ, UKinfo@winplus-europe.comwww.winplus.netWinplus AsiaSuite 6-11, 7th Flr Corporation Park11 On Lanai St., Shatin NT, Hong Kong info@winplus.netwww.winplus.netWinplus AustraliaUnit 2, 991Mountain Hwy Boronia Victoria, Australie 3155 customercare@winplus.com.auwww.winplus.com.auWinplus New Zealand22-24 Olive Road, PenroseAukland, New ZealandGriffiths Equipmentweb@griffiths.co.nzwww.types.co.nz• Distracted driving is dangerous. Always use the Bluetooth® Device in a manner that does not reduce your attention and ability to drive carefully and safely.• Adhere to all applicable traffic laws and motor vehicle regulations applicable to the device.• Consult local laws and regulations for any restrictions on installation or use.• Do not install on or near an airbag. Such installation could interfere with airbag deployment or could cause the product or another object to become a projectile, which could result in serious personal injury to occupants.• Ensure the product location will not obstruct your vision while driving.• Observe all signs that require an electrical device or RF radio product to be switched off in the designated areas. These could include hospitals, blasting areas, and potentially explosive atmospheres.• Never allow children to play with the device. Small parts may be a choking hazard.• Always practice safe driving habits.• Ensure that the charging cable does not interfere with your line of site while driving when the device is being charge.• Improper use and installation may cause severe injuries, make sure to follow installation instruction and safety procedure.CONTENTS1 23 4DISCLAIMERWARRANTY / LIABILITIESPACKAGE CONTENTINSTALLATIONBATTERY OPERATIONSSPEAKERPHONE OPERATIONSBUTTON FUNCTIONSLCD DISPLAY INDICATIONLED INDICATIONCARE AND MAINTENANCETROUBLE SHOOTINGCUSTOMER SERVICE / CONTACT US PAGEFCC/ ICCDISCLAIMERWARRANTY / LIABILITIESPACKAGE CONTENT SPEAKERPHONE OPERATIONSBATTERY OPERATIONSBUTTON FUNCTIONS LCD DISPLAY INDICATIONTROUBLE SHOOTINGFCC/ ICC LED INDICATIONCARE AND MAINTENANCECUSTOMER SERVICE / CONTACT US INSTALLATION© 2008 Winplus North America Inc. All Rights Reserved. Winplus, the logo design, and yada are trademarks or registered trademarks of Winplus North America Inc. The Bluetooth® word mark and logos are owned by the Bluetooth SIG, Inc. and any use of such marks by Winplus North America Inc. is under license.U.S. and International Patents PendingCONDITIONS OF WARRANTYIf during the 90 day warranty period your new product is found to be defective, WINPLUS North America will repair such defect, or replace the product, without charge for parts or labor subject to the following conditions:1. All repairs must be performed by WINPLUS North America.2. All warranty claims must be accompanied by a copy of the sales receipt or bill of sale.3. The equipment must not have been altered or damaged through negligence, accident, improper operation, or failure to follow the product instructions for installation, use, or care.4. The replacement of parts is excluded from the warranty when replacement is necessary due to normal wear and tear.5. Repair or replacement parts supplied by WINPLUS North America under this warranty are protected only for the unexpired portion of the original warranty.6. This is a “repair or replace” warranty only, and does not cover the costs incurred for the installation, removal or reinstallation of the product, or damage to any mobile phone devise or vehicle.OWNER’S RESPONSIBILITIES:WINPLUS North America will make every effort to provide warranty service within a reasonable period of time. SHOULD YOU HAVE ANY QUESTIONS ABOUT SERVICE RECEIVED OR IF YOU WOULD LIKE ASSISTANCE IN OBTAINING SERVICE, PLEASE CALL TOLL FREE 1.866.294.9244 DURING REGULAR BUSINESS HOURS MONDAY THROUGH FRIDAY 9:00 AM TO 5:00PM.Note: Toll Free # is for North America Customers ONLY. See Customer service section for customer contact numbers for other regions/offices.In order to provide you with the proper warranty service, we request that you adhere to the following procedure:1. Include a copy of your sales receipt or bill of sale with your unit when it is returned for warranty service.NORTH AMERICAEUROPEAUSTRALIANEW ZEALANDASIATel: 310-638-0588Fax: 310-496-2740Tel: 44-1440-713888Fax: 44-1440-713889Tel: 61-3-9720-4143Fax: 61-3-9720-4165Tel: 64-9-5254575Fax: 64-9-5256817Tel: 852-2798-8932Fax: 852-2795-0241375 West Apra StreetRancho Dominguez, CA 90220Unit 4, Two Counties Estate, Falconer Road,Haverhill, Suffolk CB9 7XZ, U.K.Unit 2, 991 Mountain Hwy Boronia,Victoria, Australia, 315522-24 Olive Road, Penrose,Auckland, New ZealandSuites 6-11, 7th Floor Corporation Park,11 On Lai Street Shatin, N.T., Hong Kong2. If it is necessary to return your product for service, please return it securely packed, preferably in the original shipping box, and freight and insurance prepaid to the following address: ATTN: WINPLUS YADA BLUETOOTH® PRODUCTS RETURNS 375 W. Apra St. Rancho Dominguez, CA 902203. Please include a detailed explanation of the problem you are having.4. If your product is found by WINPLUS North America to have a defect in material or workmanship, within the warranty period, it will be repaired or replaced at no charge and returned to you prepaid.WINPLUS North America makes no other warranty of any kind aside from the limited express warranty stated herein.DISCLAIMER OF WARRANTIES, INCLUDING WARRANTY OF MERCHANTABILITY AND WARRANTY OF FITNESS FOR PARTICULAR PURPOSE: EXCEPT AS SPECIFICALLY SET FORTH HEREIN, NO WARRANTY OR REPRESENTATION, EXPRESS OR IMPLIED, IS MADE AS TO THE YD-V16 BLUETOOTH® REARVIEW MIRROR SPEAKERPHONE. EXCEPT AS EXPRESSLY SET FORTH HEREIN, WINPLUS NORTH AMERICA AND/OR ITS AFFILIATES EXPRESSLY DISCLAIMS, WITHOUT LIMITATION, ANY STATUTORY WARRANTIES AND ALL IMPLIED WARRANTIES, INCLUDING ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. WINPLUS North America and/or its affiliates are not responsible for a user’s intended or actual use of the YD-V16 Bluetooth® Rearview Mirror Speakerphone. In no event shall WINPLUS North America and/or its affiliates have any liability for any losses (whether direct or indirect, in contract, tort or otherwise) incurred in connection with the YD-V16 Bluetooth® Rearview Mirror Speakerphone. Neither shall WINPLUS North America and/or its affiliates have any liability for any decision, action or inaction taken by any person in reliance on the YD-V16 Bluetooth® Rearview Mirror Speakerphone, or for any delays, inaccuracies and/or errors in connection with the YD-V16 Bluetooth® Rearview Mirror Speakerphone and its functioning.WINPLUS North America and/or its affiliates shall have no responsibility or liability for damage and/or injury resulting from accidents while user is utilizing the YD-V16 Bluetooth® Rearview Mirror Speakerphone; and WINPLUS North America and/or its affiliates, the manufacturer, distributor and seller shall not be liable for any injury, loss or damage, incidental or consequential, arising out of the use or intended use of the product. 5 6WINPLUS EUROPELIMITED WARRANTY WINPLUS warrants, to the original purchaser, that its products are free from defects in material and workmanship for 12 months from the date of original purchase. Where permitted by law, WINPLUS liability shall be limited to that set forth in this limited express warranty. This limited express warranty shall be the exclusive remedy of the purchaser and WINPLUS makes no other warranty of any kind aside from the limited express warranty stated above. OWNER’S RESPONSIBILITIES: In order to provide you with the proper warranty service, we request that you adhere to the following procedure:1. Include a copy of your sales receipt or bill of sale with your unit when it is returned for warranty service.2. If it is necessary to return your product for service, please return it securely packed, preferably in the original shipping box, and freight and insurance prepaid to the following address: ATTN: WINPLUS BLUETOOTH® PRODUCTS RETURNS Unit 4, Two Counties Estate, Falconer Road Haverhill, Suffolk CB9 7XZ, UK 3. Please include a detailed explanation of the problem you are having.4. If your product is found by WINPLUS to have a defect in material or workmanship, within the warranty period, it will be repaired or replaced at no charge and returned to you prepaid. WINPLUS makes no other warranty of any kind aside from the limited express warranty stated herein.WINPLUS AUSTRALIALIMITED WARRANTYThis product is warranted against faulty workmanship for a period of 12 months from the date of purchase. Winplus’ liability is limited to replacement of the product. Claims for associated or consequential loss or damage will not be accepted by Winplus. Product is not fitted, used or installed in accordance with instructions will not be eligible for warranty.WINPLUS makes no other warranty of any kind aside from the limited express warranty stated herein.• Pull the tension clamp and clip to the existing rearview mirror• Push the rearview mirror speakerphone until it is flushed against original rearview mirror Warning: Do not pull or remove the rearview mirror without pulling apart the tension clamp.B. Low Battery Power IndicatorWhen battery power is low, the device will:• Flash red LED lightRecharge the YD-V16 immediately after the low battery indicators are detected. The LED light will not turn on indicating battery power is completely consumed. Follow “Charging The Batteries” instructions above to recharge the YD-V16.The YD-V16 will not power on until it is connected to a power outlet to recharge. Recharge the YD-V16 sufficiently before using. 7 8 IMPORTANT: Before using the YD-V16 Bluetooth® Rearview Mirror Speakerphone:• Fully charge the battery (8 hours continuous) for first time use• Only use rechargeable batteries providedA. Charging the BatteryFollow the steps below when charging the YD-V16 Bluetooth® Rearview Mirror Speakerphone• Connect the DC power jack to the YD-V16 Bluetooth® Rearview Mirror Speakerphone• Connect car charger to cigarette power outlet• LED will flash red when charging is initiated • Red LED will flash off when charging is complete IMPORTANT: Remove device from cigarette outlet before leaving the vehicle. Do not leave the YD-V16 Bluetooth® Rearview Mirror Speakerphone charging in the vehicle unattended.CAUTION: Risk of explosion if battery is replaced by an incorrect type. Dispose of used batteries according to the instructions.Note: Actual talk time and standby time for the YD-V16 will vary with different Bluetooth® enabled mobile phones due to different implementation of power down modes.A. Power on/offTo turn the YD-V16 on:• Press and hold the Power Switch Button until the LED flashes blue• Release the button and wait for YD-V16 to enter into search mode Searching• Device will stay in search mode for 5 seconds• If no device was found, YD-V16 will stay on the screen • To search again, press phone button once to activate search mode SearchingNote: Before automatic connection, please make sure Bluetooth® mode on your mobile phone is activated and you must have at least successfully paired and connected to YD-V16 at least once in order to activate this feature.To turn the YD-V16 off:• Press and hold the Power Switch Button for at least 5 seconds B. Pairing/LinkingPairing Bluetooth® enabled devices like mobile phones with the YD-V16 Bluetooth® Rearview Mirror Speakerphone authorizes the devices to work with each. This step only needs to be performed once. Before Pairing the YD-V16 Bluetooth® Rearview Mirror Speakerphone:• Ensure the YD-V16 is fully charged• Charging cable is disconnected• You have the pairing instruction of your Bluetooth® wireless phone910It is recommended that you follow the pairing instructions provided by your mobile phone to ensure you successfully pair the YD-V16 Speakerphone with your mobile phone. If you do not have your mobile phone’s instruction manual available, follow the typical pairing instructions below:• Power on the YD-V16 and wait until device completed the search mode• Press and hold MENU for 2 seconds • Screen will indicate Pair Mode• Turn on your mobile phone• Select SET-UP or CONNECT from your mobile phone menu• Find and select OPTION to discover Bluetooth® devices; establishing a connection may take several minutes• If found, phone display should indicate YD-V16 or Select “YD-V16” from the list• Phone should give you a prompt asking if you want to pair the device• Select OK or ACCEPT and wait for prompt to enter passkey or PIN• Enter the code 0000 when a passkey is requested• Select “OK” to pair the YD-V16 and the handset• When pairing is complete, the YD-V16’s LCD will show PAIRING SUCCESSFUL icon Pair OKNote: If the YD-V16 and mobile handset did not successfully pair, follow the steps below to retry pairing:• Turn the phone off; wait for 10 seconds• Turn phone power on• Repeat the pairing instructions from the beginningTo Link YD-V16 to your mobile phone after pairing:• Pressing the SEND button of your YD-V16 or • Establishing the connection via your mobile phoneNote: Make sure Bluetooth® has been activated on your mobile phone before you press the SEND button. (Please refer to your mobile’s operation manual about connecting Bluetooth® devices)Once it is connected: • YD-V16 will emit a beep• The mobile’s ID will be displayed on the screen (Ex. “Motorola V3”)C. Phonebook1. Phonebook Set-up via AT Command AT Command and OPP (Object Push Profile) function can automatically transfer the contacts in your mobile phone to the YD-V16 Rearview Mirror Speakerphone.Note: NOT ALL MOBILE PHONES SUPPORT AT Command and OPP FeaturesTo transfer the Phone Book from your mobile phone via AT Command:• Make sure the YD-V16 and mobile phone is connected• Press Menu• Scroll the menu by pressing or button until you see Contact list• Press Menu button to enter Phonebook Transfer Inquire• Press Send button to start or press End button to end• LCD will display Downloading... to indicate Phonebook transfer is in process• Once transfer is successful, LCD will display Download Complete11 122. Phonebook Set-up via OPPThe YD-V16 supports single contact or group contacts transfer via OPP function. For details on operating procedures, please refer to your mobile phone’s user manualTo transfer the Phone Book from your mobile phone via OPP:• Disconnect Bluetooth® link from the YD-V16 setting (if it is connected)• Setup mobile phone for copying and transferring the contacts from the mobile phone to your YD-V16 Note: Please refer to your mobile phone’s user manual• LCD will display Downloading to indicate contacts transfer is in process• Once transfer is completed, LCD will show number of records transferred • Reconnect the Bluetooth® link of your YD-V16 and mobile phoneNote: Some mobile phones are able to register multiple phone numbers under the same name. The YD-V16 phonebook can distinguish the numbers using the letters: <M> for mobile phone number, <H> for home number and <O> for office number 3. Deleting Phonebook entries:To delete Phone Book entry:• Press Menu• Scroll the menu by pressing or button until you see Delete Contact• Press Send button• LCD will display Yes or No?• Press Send button to confirm.• LCD will display Deleting Contact while phone book entries are being deleted• LCD will display Deleted ALL when phone book is cleared• Press End button to return to Main MenuNote: YD-V16 does not allow deleting of a single entry; ALL entries will be deleted after confirmation4. Speed Dial Set-upNote: Phonebook should be set up first to activate speed dialing.To set up speed dialing:• Press Menu• Scroll the menu by pressing or button until you see Quick Dial• Press Send button• Browse for an empty memory slot by pressing or button. There are a total of 3 memory slots for speed dialing with each slot represented by the , button and the Menu button• Press the Menu button after finding an empty slot• Browse the phone number that you wish to set to speed dial• Press Send button to confirm• Press End button to return to Main MenuNote: If a memory slot is empty, user can simply press the desired key for 2 seconds then follow the above procedures.13 14To modify/delete speed dialing number:Once you have saved a number for a slot/button, you need to delete it before you can save a new number for that slot/button.To delete a number in a speed dialing entry:• Press Menu• Scroll the menu by pressing or button until you see Quick Dial• Search for the entry that you would like to modify• Press Menu button twice and the screen will show Delete ?• Press Send button to confirm or End button to cancelD. LCD DisplayTo adjust contrast of LCD Display:• Press Menu• Scroll the menu by pressing or button until you see Contrast Setting• Press Send button to enter• The status bar is shown in the contrast menu. This indicates the contrast level of the LCD display• Press the or button to adjust to desired contrast level• Press Send button to save settingE． Volume AdjustmentsTo adjust ring volume:• Press the or button to adjust ring volume To adjust call volume:• Press the or button to adjust the volume during a callTo adjust microphone volume during a call:• Press and hold Up button for two seconds to increase microphone volume• Press and hold Down button for two seconds to decrease microphone volumeIf you cannot hear the person you are talking to on the other line, do the following steps while conversation is in progress:• Adjust the microphone volume of the YD-V16 to maximum level or• Request the person on the other line to adjust his/her mobile phone’s volume level to maximumIf there is a strong echo when the person on the other line talks:• Transfer the call to your mobile phone• If echo disappeared, transfer the call to your YD-V16 again and lower the loud speaker volume until echo is reduced/eliminated• If the echo remains, root cause of the echo might be with the network provider or the mobile phone itself. If the loudspeaker volume of the YD-V16 is too low or too high and you are unable to adjust it:• Adjust the volume directly on the mobile phone• Fine tune it using the volume control of the YD-V1615 16Mute/Un-mute FunctionsTo mute the YD-V16 during an active call:• Press Menu button for two secondsTo cancel mute:• Press Menu button againF. Call Operations1. Making a CallTo make a call using the phone book:• Press Menu button• Press the or button until you see Contact list• Press Send button to enter • Select name by pressing the or button• Press Send button to enter• Press Send button again to dialTo call last number dialed: • Press Send button • Press the or button until you find the desired last dialed number• Press Send button again to dialTo call using the speed dialing function:• Press and hold the Menu button or the or button for 2 seconds • Phone will automatically dial the number set to Speed Dial for that particular buttonTo make a call using the voice dialing function:To enter voice dialing mode:• Hold the Send button for 2 seconds• Say the name after you hear the toneNote: If the YD-V16 failed to recognize the voice/name. Press the End button to exit and repeat the above steps for voice dialing.Note: Voice Dialing is a feature of your mobile phone. Please refer to your phone's user manual for voice command operation.2. Answering CallsTo answer calls via the YD-V16:• Press the Send button when ring tone is heard or• Answer the call via the mobile handset3. Ending CallsTo end a call:• Press the End button or• End call using the mobile handset4. Rejecting CallsTo reject a call:• Press the End button 17 187. Interchanging YD-V16 and HandsetYou may interchange the call between your handset and YD-V16 while conversation is ongoing To shift from YD-V16 to handset or vice versa:• Press and hold the Send button for two seconds19 2021 2223 2425 26!!!USB outletmicrophonevolume downsendmenuendstatus LEDvolume upDC jack outletcaller ID screenPower Switch Button(end)Phone ButtonGo to MenuButton Function OperationCONTACT LISTCONTRAST SETTINGDISCONNECT BTQUICK DIALDELETE CONTACTPairingDelete a number saved in Quick DialMute Un-muteDTMF (Dial Tone Modulation Frequency) Activated only when the line is connectedTransfer phonebook contacts from mobile phone and SIM to YD-V16 via AT or OPP commandPress 1 timeAdjust LCD ContrastDisconnect Bluetooth®With 3 memory slots for quick dialingDelete entire phonebook contentPress and hold for 2 seconds(Screen shows “Pair Mode”)Press twice (screen will show “DELETE?”)Press 1 timePress 1 timeWelcome ScreenBluetooth® Pairing ModeBluetooth® Pairing SuccessfulBlinking to indicate Bluetooth® Search ModeBluetooth® DisconnectedOutgoing CallIncoming CallMissed CallMenuReception Signal Strength Indicator (for mobile phone only)Call transfer to mobile during a callVoice DialingCall Register (Outgoing Call/Incoming Call/Missed Call)Volume IndicatorAT Command InquireAT Command Phone Book Transfer in ProcessAT Command Phone Book Transfer FinishedOPP Phone Book Transfer in ProcessMenuMake / Receive callVoice dialingConversation transferBluetooth® link connectionYES End CallReject CallNoIncrease VolumeScroll UpwardMove leftIncrease Microphone Gain Decrease VolumeScroll downwardMove rightSteadyBlinking (every 30 seconds)Blinking (every 5 seconds)Battery charging in progressBattery low; recharging is recommendedUnit is powered onDecrease Microphone Gain ButtonLED LightRED LightBLUE LightStatus IndicationFunction OperationLCD Display IndicationPress 1 timePress 1 timePress 1 timePress 1 timePress 1 timePress repeatedly until you reach desired volume levelPress repeatedly until you find desired entry/menu itemPress repeatedly until you find desired entry/menu itemPress and hold for 2 secondsPress repeatedly until you reach desired volume levelPress repeatedly until you find desired entry/menu itemPress repeatedly until you find desired entry/menu itemPress and hold for 2 secondsPress 1 time after pairingPress and hold for 2 seconds to enter voice dialing modeWhile conversation is ongoing, press and hold for 2 secondsYD-V16YD-V16Pair ModePair OKSearchingNAMENAME1 Missed CallDownload Contact?Downloading...Downloading 1Download CompleteContact listBluetooth® Rearview Mirror SpeakerphoneCar ChargerVelcro Straps*For added safety, use Velcro straps- Clip and attach the Velcro clips to the back of the mirror (see above image)- Loop the straps around the vehicle rearview mirror- Press Velcro straps together to secure- Reorient or relocate the receiving antenna.- Increase the separation between the equipment and receiver.- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.- Consult the dealer or an experienced radio/TV technician for help.This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment.To comply with FCC RF exposure requirements, the device and the antenna for this device must be installed to ensure a minimum separation distance of 20cm or more from a person's body. Other operating configurations should be avoided.IC statementOperation is subject to the following two conditions:1) This device may not cause interference and2) This device must accept any interference, including interference that may cause undesired operation of the device.This device has been designed to operate with an antenna having a maximum gain of 0 dBi. Antenna having a higher gain is strictly prohibited per regulations of Industry Canada. The required antenna impedance is 50 ohms.Federal Communication Commission Interference StatementThis equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures:

Navigation menu