Wireless Environment MBN200 NetBright Motion Sensor User Manual
Wireless Environment LLC NetBright Motion Sensor
User Manual
| Download: |  |
| Mirror Download [FCC.gov] | |
| Document ID | 3853985 |
| Application ID | 7t+HX5MJzVqhCUKnb3yifg== |
| Document Description | User Manual |
| Short Term Confidential | No |
| Permanent Confidential | No |
| Supercede | No |
| Document Type | User Manual |
| Display Format | Adobe Acrobat PDF - pdf |
| Filesize | 73.38kB (917202 bits) |
| Date Submitted | 2018-05-17 00:00:00 |
| Date Available | 2018-05-17 00:00:00 |
| Creation Date | 2018-02-13 16:17:40 |
| Producing Software | Adobe PDF Library 15.0 |
| Document Lastmod | 2018-05-16 17:01:27 |
| Document Title | User Manual |
| Document Creator | Adobe InDesign CC 13.0 (Macintosh) |
Installation Instructions NetBright Motion Sensor MBN200 Thank you for purchasing the Mr Beams ® NetBright Motion Sensor. We are certain that your motion sensor will contribute to a safer environment and provide supplemental motion for your NetBright system. Tips: • Use only new alkaline AA-cell batteries with 1.5V rating. • Do not mix old and new batteries. If batteries are not new, it may cause the sensor to malfunction. • Install batteries with polarity in correct position. What is included per light: • 2 screws, 2 anchors What you need to install: • 2 AA-cell alkaline batteries (per sensor) • Drill or screwdriver Motion Sensor Features: Motion/light sensor: Sensor instantly turns on when it detects motion. The light sensor conserves battery life by preventing the sensor from activating in daylight. Durable, Weather Resistant: Tight seals and UV resistant material allow the sensor to work in all weather conditions. Networking: The Motion Sensor will activate any light in the network when it detects motion. 1. Remove the screw on the back of the motion sensor. 2. Slide the battery cover off the motion sensor and set aside. Motion & Light Sensor 3. Insert 2 new AA alkaline batteries and replace the battery cover. Setting up Devices to a Network Choose a group or channel for your device with the dipswitches next to the battery compartment. Ensure all units are on the same channel by matching the dipswitch positions. 5. To mount the sensor with the included screw, line up the battery cover with desired mouting location and mark with a pencil. Use the hole from the battery cover screw to mark the pilot hole. 6. Use a 1/16” drill bit to create the pilot hole. Insert the included screw and leave some room for the sensor to slide onto. Slide the sensor onto the screw. Battery Caution: 1) Do not mix old and new batteries 2) Do not mix Alkaline, Standard Carbon-Zinc, Rechargeable Nickel Cadmium or Nickel Metal Hydride batteries 3) Do not dispose of batteries in fire 4) Batteries should be recycled or disposed of as per state and local guidelines www.mrbeams.com WARNING: This product contains chemicals known to the State of California to cause cancer and birth defects or other reproductive harm. FCC WARNING: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installa- tion. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or televi- sion reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: •Reorient or relocate the receiving antenna. •Increase the separation between the equipment and receiver. •Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. •Consult the dealer or an experienced radio/TV technician for help. Caution: Any changes or modiÞcations to this device not explicitly approved by manufacturer could void your authority to operate this equipment. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. The device has been evaluated to meet general RF exposure requirement.
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.6 Linearized : No Create Date : 2018:02:13 16:17:40-05:00 Creator : Adobe InDesign CC 13.0 (Macintosh) Modify Date : 2018:05:16 17:01:27+08:00 Language : en-US Tagged PDF : Yes XMP Toolkit : Adobe XMP Core 4.2.1-c041 52.342996, 2008/05/07-20:48:00 Metadata Date : 2018:05:16 17:01:27+08:00 Creator Tool : Adobe InDesign CC 13.0 (Macintosh) Instance ID : uuid:f77114ea-7d54-4f7d-b22d-2e2f16a5338e Original Document ID : xmp.did:358C138F272068118C14D63ED8DFD8B8 Document ID : xmp.id:ce278c64-74b6-4c94-b034-02a7f5e79b09 Rendition Class : proof:pdf Derived From Instance ID : xmp.iid:9e11a1ad-6457-4b49-8535-5c856d434845 Derived From Document ID : xmp.did:6c35582c-bc4c-42ec-ac31-46f3b5a9e0aa Derived From Original Document ID: xmp.did:358C138F272068118C14D63ED8DFD8B8 Derived From Rendition Class : default History Action : converted History Parameters : from application/x-indesign to application/pdf History Software Agent : Adobe InDesign CC 13.0 (Macintosh) History Changed : / History When : 2018:02:13 16:17:40-05:00 Format : application/pdf Producer : Adobe PDF Library 15.0 Trapped : False Page Count : 2EXIF Metadata provided by EXIF.tools