Wistron NeWeb BLANKA WNC RFID Smart Reader User Manual

Wistron NeWeb Corporation WNC RFID Smart Reader

User Manual

RFID Smart Reader with Fan-out Box and RF Switch User Manual English
Table of Contents WNC RFID Smart Reader Wistron NeWeb Corporation© 1 1. GETTING STARTED .................................................................................... 2 1.1 IN THE PACKAGE ........................................................................................ 2 1.2 INTRODUCTION .......................................................................................... 2 1.3 HARDWARE OVERVIEW- RFID SMART READER ............................................ 4 1.4 HARDWARE OVERVIEW- FAN-OUT BOX ........................................................ 5 1.5 HARDWARE OVERVIEW - RF SWITCH ........................................................... 5 1.6 CONNECTING THE CABLES .......................................................................... 6 2. CONFIGURATION SOFTWARE ................................................................... 9 2.1 ACCESS THE MANAGEMENT INTERFACE ....................................................... 9 2.2 MANAGEMENT ........................................................................................... 9 3. APPENDIX .................................................................................................. 10 3.1 SPECIFICATIONS: RFID SMART READER .................................................... 10 3.2 SPECIFICATIONS: FAN-OUT BOX ................................................................ 12 3.3 SPECIFICATIONS: RF SWITCH ................................................................... 13 3.4 PIN DEFINITION ....................................................................................... 14
1 Getting Started WNC RFID Smart Reader Wistron NeWeb Corporation© 2 1. Getting Started 1.1 In the Package RFID Smart Reader Power Cord Power Adapter Fan-out Box (optional) RF Switch (optional) Note: The Fan-out Box and RF Switch work in combination to allow more antenna connections. One RFID Smart Reader can connect to one Fan-out box and four RF switches. 1.2 Introduction The WNC RFID Smart Reader (the Reader) is suitable for a variety of UHF RFID applications. It provides high level RF performance, a user-friendly software development interface and a cost competitive reader solution. Combined with a Newave Shelf Antenna, it can provide 100% readability in zone sizes of 2’x2’x2’ to 10’x10’x10’ with appropriate reader parameters and antenna setup. You can also connect the Reader to a fan-out box and 1~4 RF switches to add additional antennas. A maximum of 16 antennas are allowed for one Reader. For multi-reader applications, such as retail applications, the Reader solution can efficiently compress data size and solve data traffic issues.
1 Getting Started WNC RFID Smart Reader Wistron NeWeb Corporation© 3 Basic application: You can connect to up to four antennas and use a computer to monitor detected parameters. Advanced application: Use the Reader with a Fan-out Box and an RF Switch to connect up to 16 antennas.
1 Getting Started WNC RFID Smart Reader Wistron NeWeb Corporation© 4 1.3 Hardware Overview- RFID Smart Reader Front Panel Rear Panel WAN Connect a standard RJ-45 Ethernet cable to the port to establish a network connection. This feature allows you to configure settings or read the data from the Reader on your computer via a Graphic User Interface. WAN port supports Power over Ethernet (PoE). LAN Currently unavailable. DC IN Connect the power adapter to the Reader via this inlet to power on the Reader. GPIO For GPIO purposes such as connecting a Fan-out Box, light sensor or other sensors. Antenna Ports For RF cable insertion. The Reader supports up to four antennas at the same time. Additional connection is also possible via an optional antenna switch. Note: RJ-45 Ethernet cable and RF cable not included in the package.
1 Getting Started WNC RFID Smart Reader Wistron NeWeb Corporation© 5 1.4 Hardware Overview- Fan-out Box OUTPUT For RF Switch connection. INPUT Connect to the GPIO port of the Reader. Device 1 & 2 Sensor data input/output ports for other applications, for example, connecting to entrance and exit sensors for security control. 1.5 Hardware Overview - RF Switch INPUT Connect to an OUTPUT port of the Fan-out Box. RF IN Connect to an antenna port of the Reader. ANT 1~4 For antenna connection.
1 Getting Started WNC RFID Smart Reader Wistron NeWeb Corporation© 6 1.6 Connecting the Cables Basic installation: 1. Plug an RF cable into an antenna port and an antenna. The Reader supports up to four antennas at the same time. 2. Connect an RJ-45 Ethernet cable to the WAN port and to your computer for software development interface configuration. 3. Connect the power adapter to the DC IN inlet on the Reader. Once the power adapter is connected to the Reader, the Power LED indicator will turn green indicating the power is on. Note: Reader may be wall-mounted. Insert screws via the four holes on the left and right side of the Reader.
1 Getting Started WNC RFID Smart Reader Wistron NeWeb Corporation© 7 Installation with Fan-out Box and RF Switch:
1 Getting Started WNC RFID Smart Reader Wistron NeWeb Corporation© 8 1. Use an RF cable to connect an antenna port of the Reader to the RF IN port of the RF Switch, and then connect the antennas to the ANT1~4 ports of the RF Switch. 2. Use a DB9 cable to connect the GPIO port of the Reader and the INPUT port of the Fan-out box. Note: Only use a rollover type DB9 cable (not crossover type.) The cable must be shorter than 5m. 3. Use a DB9 cable to connect an OUTPUT port of the Fan-out Box to the INPUT port of the RF Switch. Note: Only use a rollover type DB9 cable shorter than 30m. 4. Connect the Reader to a computer. Attach the power supply to the Reader and plug it into a wall outlet. 5. You can also connect the Device1 & 2 ports to receive data from other devices such as sensors. Note: The Reader, Fan-out Box and the RF Switch may be wall-mounted. Insert screws via the four holes on the left and right side of them. 1.5 LED Status (RFID Smart Reader) Status LED Green Red Off Power On: Powered on On: Power booting No Power Data Blinking: Data transmitting N/A No transmission Port 1 ~ 4 On: Port enabled Blinking: RF inventory On: Port error Blinking: RF failure Port disabled
2 Software WNC RFID Smart Reader Wistron NeWeb Corporation© 9 2. Configuration Software 2.1 Access the Management Interface 2.2 Management
3 Appendix WNC RFID Smart Reader Wistron NeWeb Corporation© 10 3. Appendix 3.1 Specifications: RFID Smart Reader RF System Chipset Impinj R2000 ATMEL AT91SAM7S-256 Protocol RFID Protocol Support EPC Global Gen 2 ISO 18000-6C; ISO 18000-6B (optional) Support EPC DRM Yes (with DRM Filter) switchable RF Frequency US: 902 ~ 928MHz EU: 865 ~ 868MHz KR: 910 ~ 914MHz PRC: 920 ~ 925MHz Open: 840MHz ~ 960MHz Demodulation ASK or PSK Modulation Depth 90% nominal Data Encoding FM0 or Miller code Bit Rate Supports uplink data rates of up to 640 Kbps TX Output power 28 dBm Antenna Type 4 port Mono-static Antenna connector 4 pcs RP TNC General Characteristics Dimensions 18.2 x 13 x 2.6 cm Weight ~550g Base Material Aluminum alloy (AL 5052) Mounting Wall, floor Power Input 1. POE 802.3at 2. DC power input (12 VDC +/-5%, 30W) Power Consumption 11W
3 Appendix WNC RFID Smart Reader Wistron NeWeb Corporation© 11 System Architecture Processor TI TMS320DM6446 System Memory / Ram 64MB Internal Storage / Flash 128MB Communication USB N/A Ethernet 10/100 Base-T (RJ-45) X2 (POE x 1 802.3 at compliant) GPIO 4 input and 2 output (DB9) Indicators 5 two-color / 1 one-color LED status indicator Software Operation System Embedded Linux Software SDK C# Environment Humidity 5% to 95%, non-condensing Operating Temperature - 20℃ to 50℃ / -4°F to 122°F Storage Temperature - 40℃ to 85℃ / -40°F to 185°F Sealing / Dust and Water Immunity IP54 (NEMA 3)
3 Appendix WNC RFID Smart Reader Wistron NeWeb Corporation© 12 3.2 Specifications: Fan-out Box RF System Chipset MC33202DR2G Regulatory and Environmental Compliance EMC certification FCC 47 CFG Ch.1 Part 15 (US) (15.247) ETSI EN 302 208-1 (V1.1.1) (EU) (optional) Certification RoHS / FCC / CE(optional) General Characteristics Dimensions 12.5 x 6.2 x 2.6 cm Weight ~250g Base Material Aluminum alloy (AL 5052) Mounting Wall, floor Power Consumption 0.5W Communication Input port 1 DB9 female connector Output port 4 DB9 female connector External port 2 ACES product:2.0mm WTB WAFER CONN Environment Humidity 5% to 95%, non-condensing Operating Temperature - 20℃ to 50℃ / -4°F to 122°F Storage Temperature - 40℃ to 85℃ / -40°F to 185°F Sealing / Dust and Water Immunity IP54 (NEMA 3)
3 Appendix WNC RFID Smart Reader Wistron NeWeb Corporation© 13 3.3 Specifications: RF Switch RF System Chipset SN74HC139PWR SN74HC240PWR AS221 RF Frequency US: 902 ~ 928MHz/ EU: 865 ~ 868MHz/ KR: 910 ~ 914MHz/ PRC: 920 ~ 925MHz/ Open:840MHz ~ 960MHz/ Typical Insertion Loss 1.2dB Typical Isolation 36dB Regulatory and Environmental Compliance EMC certification FCC 47 CFG Ch.1 Part 15 (US) (15.247) ETSI EN 302 208-1 (V1.1.1) (EU) (optional) Certification RoHS / FCC / CE(optional) General Characteristics Dimensions 11.4X5.8X2.6 cm Weight ~350g Base Material Aluminum alloy (AL 5052) Mounting Wall, floor Communication Input port 1 DB9 female connector R-TNC 4 R-TNC Connector Environment Humidity 5% to 95%, non-condensing Operating Temperature - 20℃ to 50℃ / -4°F to 122°F Storage Temperature - 40℃ to 85℃ / -40°F to 185°F Sealing / Dust and Water Immunity IP54 (NEMA 3)
3 Appendix WNC RFID Smart Reader Wistron NeWeb Corporation© 14 3.4 Pin Definition GPIO port of RFID Smart Reader DB9 Female connector Pin1 5V Pin2 Output port1, 3.2V Pin3 Output port3, 3.2V Pin4 Input port1, 3.2V Pin5 Ground Pin6 Ground Pin7 Output port2, 3.2V Pin8 Output port4, 3.2V Pin9 Input port2, 3.2V Output ports of Fan-out Box Output Port Pin1 5V Pin2 GPO_1- Pin3 NC Pin4 GPO_2+ Pin5 Ground Pin6 Ground Pin7 GPO_1+ Pin8 GPO_2- Pin9 NC
3 Appendix WNC RFID Smart Reader Wistron NeWeb Corporation© 15 Device 1&2 ports of Fan-out Box Device 1 Pin1 5V Pin2 GPI_1 Pin3 GPO_3 Pin4 Ground Device 2 Pin1 5V Pin2 GPI_2 Pin3 GPO_4 Pin4 Ground
Federal Communication Commission Interference Statement This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures: - Reorient or relocate the receiving antenna. - Increase the separation between the equipment and receiver. - Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. - Consult the dealer or an experienced radio/TV technician for help. FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. Radiation Exposure Statement: This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body.
台灣使用注意事項: 經型式認證合格之低功率射頻電機，非經許可，公司、商號或使用者均不得擅自變更頻率、加大功率或變更原設計之特性及功能。 低功率射頻電機之使用不得影響飛航安全及干擾合法通信；經發現有干擾現象時，應立即停用，並改善至無干擾時方得繼續使用。前項合法通信，指依電信法規定作業之無線電通信。低功率射頻電機須忍受合法通信或工業、科學及醫療用電波輻射性電機設備之干擾

Navigation menu