Wistron NeWeb DFCN2 NFC MODULE User Manual

Wistron NeWeb Corporation NFC MODULE

User Manual

  USER  MANUAL      DFCN2 NFC MOUDULE    USER MANUAL & Operational description
  USER  MANUALI. IntroductionDFCN2 is a kind of NFC (Near Field Communication) module that could be embedded in one IT system by simply connecting the module to his target microcontroller and start developing his application software.  II. DESIGNREFERENCEDFCN2 reference design module consists of the following:   • Reference Design:   When the user wishes to incorporate the DFCN2 to their device, it is strongly recommended that this reference design is copied “as is” in the final application board to guarantee optimum performance, regulatory compliance and lowest development time and design effort.    • MCU FPC/FFC Connector:   Allow user to connect the DFCN2 module to the host board via FPC/FFC connector.   • Antenna Connector:   Connected to FPC antenna, please note that matching circuitry should designed on antenna.  
  USER  MANUALIII. FEATURE Cont act less prot ocols:    •  I SO14443 A/ B   •  I SO15693   •  I SO18092    Contact less t ransm ission of data and RF energy    Peer- t o- peer com m unication    Card em ulat ion  NFC card reader/ writer  Program m able receiver sensit ivity    Carrier frequency:  13.56 MHz    RF Field detect ion    Single ended external ant enna connect ion   IV. OperationConditionsSupply voltage    AC mains    DC   Type of DC Source    Internal DC supply    External DC adapter    Battery Operational Climatic    Tnom (20°C)   Tmax (55°C)   Tnim (-20°C) V. Assembly Guidelines
  USER  MANUALVI. MECHANICALDIMENSION
  USER  MANUALVII. CertificationsandRegulatoryItem  Feature  Description 6.1 FCC RF: FCC part 15C EMI: FCC part 15B FCC grant: TCB Filing fee 6.2 CE RF: EN302291 Class B EMC: EN301489-1/-3 Safety: EN 60950-1:2006/A11:2009 6.3 IC  RSS-210 ISSUE 8 RSS-GEN ISSUUE 3  General: This modular approval is limited to OEM/Integrators installation only.   OEM integrators are responsible for ensuring that the end-user has no manual instructions to remove or install module.  End Product Labeling (FCC) When the module is installed in the host device, the FCC ID label must be visible through a window on the final device or it must be visible when an access panel, door or cover is easily re-moved. If not, a second label must be placed on the outside of the final device that contains the following text: “Contains FCC ID: NKR-DFCN2”. The grantee's FCC ID can be used only when all FCC compliance requirements are met.      Required FCC Compliance Statement for Host Integration To integrate this module into the host, the host manufacturer is responsible for the applicable FCC rules, including the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. In the user manual of the host device, the following statements are required to be included.  This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
  USER  MANUAL This device has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiated radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: –Reorient or relocate the receiving antenna. –Increase the separation between the equipment and receiver. –Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. –Consult the dealer or an experienced radio/TV technician for help.  Changes or modifications not expressly approved by the party responsible for compliance could void the user‘s authority to operate the equipment.  FCC Module Integration Restriction: This module has been certified by FCC as single module approval with the following restrictions: 1. The Loop antenna was verified in the conformity testing, and for compliance the antenna shall not be modified. A separate approval is required for all other operating configurations, including different antenna configurations. 2. If any other simultaneous transmission radio is installed in the host platform together with this module, or above restrictions cannot be kept, a separate RF exposure assessment and FCC equipment authorization is required.  End Product Labeling (IC) Labeling Requirements for the Host Device (from Section 3.2.1, RSS-Gen, Issue 3, December 2010): The host device shall be properly labeled to identify the module within the host device. The Industry Canada certification label of a module shall be clearly visible at all times when installed in the host device, otherwise the host device must be labeled to display the Industry Canada certification number of the module, preceded by the words ―Contains transmitter module, or the word ―Contains, or similar wording expressing the same meaning, as follows: "Contains transmitter module IC: 4441A-DFCN2 ".  Required IC Compliance Statement for Host Integration To integrate this module into the host, the host manufacturer is responsible for the applicable Industry Canada rules, including the limits for a Class B digital device, pursuant to ICES-003 of the Industry Canada Rules
  USER  MANUALIn the user manual of the host device, the following statements are required to be included.  This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions:   (1) this device may not cause interference, and   (2) this device must accept any interference, including interference that may cause undesired operation of the device.  This Class B digital apparatus complies with Canadian ICES-003.   Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est autorisée aux deux conditions suivantes:   (1) l'appareil ne doit pas produire de brouillage, et   (2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d'en compromettre le fonctionnement."  Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada.  IC Module Integration Restriction: This module has been certified by Industry Canada as modular approval with the following restrictions: 1. The Loop antenna was verified in the conformity testing, and for compliance the antenna shall not be modified. A separate approval is required for all other operating configurations, including different antenna configurations. 2. If any other simultaneous transmission radio is installed in the host platform together with this module, or above restrictions cannot be kept, a separate RF exposure assessment and IC equipment certification is required.

Navigation menu