Wistron NeWeb DNSA144 11a/b/g/n IoT WiFi module User Manual rev

Wistron NeWeb Corporation 11a/b/g/n IoT WiFi module rev

User Manual rev.pdf

Download: Wistron NeWeb DNSA144 11a/b/g/n IoT WiFi module User Manual rev
Mirror Download [FCC.gov]Wistron NeWeb DNSA144 11a/b/g/n IoT WiFi module User Manual rev
Document ID3361267
Application IDwZlTrPTEaFtwbB+RJUbfaQ==
Document DescriptionUser Manual rev.pdf
Short Term ConfidentialNo
Permanent ConfidentialNo
SupercedeNo
Document TypeUser Manual
Display FormatAdobe Acrobat PDF - pdf
Filesize14.1kB (176274 bits)
Date Submitted2017-04-18 00:00:00
Date Available2017-10-15 00:00:00
Creation Date2017-04-13 18:57:25
Producing SoftwareGPL Ghostscript 9.04
Document Lastmod2017-04-13 18:57:25
Document TitleDNSA-144 Product Spec & manual - BV - 20170413 _FCC_
Document CreatorPDFCreator Version 1.2.3
Document Author: tting

11a/b/g/n IoT WiFi module
DNSA-144
User Manual
Copyright Statement
No part of this publication may be reproduced, stored in a retrieval system, or transmitted in any form or by any means,
whether electronic, mechanical, photocopying, recording or otherwise without the prior writing of the publisher.
All copyright reserved.
The information contained herein is the exclusive property of WNC and shall not be distributed, reproduced, or disclosed in whole or in part without prior written permission of WNC.
1/9
Revision History
Rev.
V0.3
History
- Initial version
Date
2015/2/26
Author
V0.4
- Update the mechanical dimension
2015/11/27
TT
TT
The information contained herein is the exclusive property of WNC and shall not be distributed, reproduced, or disclosed in whole or in part without prior written permission of WNC.
2/9
Federal Communication Commission Interference Statement
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC
Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will
not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which
can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of
the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that
to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the
user's authority to operate this equipment.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may
not cause harmful interference, and (2) this device must accept any interference received, including interference that may
cause undesired operation.
IMPORTANT NOTE:
Radiation Exposure Statement:
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment
should be installed and operated with minimum distance 20cm between the radiator & your body.
This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.
Country Code selection feature to be disabled for products marketed to the US/CANADA
This device is intended only for OEM integrators under the following conditions:
1) The antenna must be installed such that 20 cm is maintained between the antenna and users, and
2) The transmitter module may not be co-located with any other transmitter or antenna,
3) For all products market in US, OEM has to limit the operation channels in CH1 to CH11 for 2.4G band by supplied
firmware programming tool. OEM shall not supply any tool or info to the end-user regarding to Regulatory Domain
change.
As long as 3 conditions above are met, further transmitter test will not be required. However, the OEM integrator is still
responsible for testing their end-product for any additional compliance requirements required with this module installed
IMPORTANT NOTE
In the event that these conditions can not be met (for example certain laptop configurations or co-location with another
transmitter), then the FCC authorization is no longer considered valid and the FCC ID can not be used on the final product. In
these circumstances, the OEM integrator will be responsible for re-evaluating the end product (including the transmitter) and
obtaining a separate FCC authorization.
End Product Labeling
This transmitter module is authorized only for use in device where the antenna may be installed such that 20 cm may be
maintained between the antenna and users. The final end product must be labeled in a visible area with the following:
“Contains FCC ID: NKR-DNSA144”.
Manual Information to the End User
The OEM integrator has to be aware not to provide information to the end user regarding how to install or remove this RF
module in the user’s manual of the end product which integrates this module.
The end user manual shall include all required regulatory information/warning as show in this manual.
The information contained herein is the exclusive property of WNC and shall not be distributed, reproduced, or disclosed in whole or in part without prior written permission of WNC.
3/9
Contents
1.
KEY FEATURES ................................................................................................................................................................ 7
2.
ELECTRICAL SPECIFICATION ............................................................................................................................................ 8
3.
MECHANICAL DIMENSION AND DRAWING ................................................................................. 錯誤! 尚未定義書籤。
4.
REGULATORY & ENVIRONMENT ..................................................................................................................................... 9
5.
PACKAGE INFORMATION ................................................................................................................................................ 9
6.
ORDER INFORMATION.................................................................................................................................................. 20
The information contained herein is the exclusive property of WNC and shall not be distributed, reproduced, or disclosed in whole or in part without prior written permission of WNC.
4/9
1. Key Features
QCA4004 IoE solution
Internal PA and LNA, with external RF Switch for Antenna Diversity
2.4GHz and 5GHz Dual band IEEE 802.11a/b/g/n, single stream 1x1
11n support HT20 and HT40 Bandwidth
1 On board dual-band printed Antenna and optional U.FL antenna connectors.
GPIO voltage is flexible, can between 1.8~3.3V
Single power supply: 3.3V, Low Power Consumption, also support Green Tx and very low power sleep
mode for mobile battery operation application. Can be wake up and go to sleep quickly.
42mm x 20mm size, 2-layer, single side component
Operation temperature: -40~+85 degrees C(Industry Class Version); 0~+85 degrees C(Commercial
Class Version)
TCP/IP offload, include Encryption
QCA4004 has Hardware Wake Up Manager allow chip go to sleep and wake up later automatically.
This feature can reduce normal operation power consumption.
SPI Slave interface to the MCU.
DNSA-144 also can be host-less mode(stand-alone). Allow user to run tiny size application.
The information contained herein is the exclusive property of WNC and shall not be distributed, reproduced, or disclosed in whole or in part without prior written permission of WNC.
5/9
3. Electrical Specification
General DC electrical characteristics
These conditions apply to all DC characteristics unless otherwise specified:
Temp = 25 °C, VDD33= 3.3 V
Table 4: DC electrical characteristics for digital I/Os
Power Consumption
Vcc=3.3V, Room temperature
Condition
2.4G 11g continue Tx@6M_17dBm
2.4G 11n continue Tx@HT40MCS7_11dBm
2.4G 11b/g and 11n HT20 continue Rx
2.4G 11n HT40 continue Rx
5.18G 1a continue Tx@6M_14dBm
5.18G 11n continue Tx@HT40MCS7_6dBm
5.18G 11a and 11n HT20 continue Rx
5.18G 11n HT40 continue Rx
Average
900
630
314
340
947
660
320
342
Unit
mWatt
Note A: External IO voltage (DVDD_GPIO) can be 1.8~3.3V.
Note B: QCA4004 need 3.3V and 1.2V supply. For 1.2V supply there are 2 methods: Switching and LDO.
Inside the QCA4004, there is embedded a switching regulator to convert 3.3V to 1.2V for its chip core
voltage supply. Also it has a LDO driver to act as 3.3V->1.2V LDO driver (might need external transistor). In
The information contained herein is the exclusive property of WNC and shall not be distributed, reproduced, or disclosed in whole or in part without prior written permission of WNC.
6/9
this table we consider to use switching regulator method to have better power efficiency. The tradeoff is
we have to add a power inductor near QCA4004 chip. Also shielding height has to be caution to prevent
the inductor magnetic field interaction with the iron material in the shielding.
Absolute Rating
Symbol
Description
Range
Unit
VDDIO
All IO supply voltage
-0.3~+4.0
Volt
3.3V
All 3.3V net
-0.3~+4.0
Volt
Min Digital IO
All Digital IO pins
-0.3
Volt
Max Digital IO
All Digital IO pins
(VDDIO+0.3)
Volt
RFin
Max Input RF signal
10
dBm
Tstorage
Storage Temperature
-40~+135
℃
ESD-HBM
Human Body Model, all pins
ESD-CDM-nonRF
Charged Device Model, non-RF pins
Volt
500
Volt
ESD-CDM-RF
Charged Device Model, RF pins
400
Volt
Note: This table is the level that could permanent cause damage to the module. For normal operating,
please use below table for design consideration.
Recommend Operating Condition
Symbol
Description
Range
Unit
VDDIO_GPIO
All IO supply voltage
1.8~3.4
Volt
3.3V
All 3.3V net
3.15~3.45
Volt
Min Digital IO
All Digital IO pins
-0.2
Volt
Max Digital IO
All Digital IO pins
(VDDIO+0.2)
Volt
SPI slave interface electrical timing diagram
The information contained herein is the exclusive property of WNC and shall not be distributed, reproduced, or disclosed in whole or in part without prior written permission of WNC.
7/9
Fig.4: SPI salve timing
Table 4: SPI slave port timing (48 MHz reference clock)
RF path:
A. There is a SPDT RFSW to do the diversity between 2 RF ports during normal mode.
B. For Port0, there are 2 options, U.FL0 or printed antenna by a jumper capacitor.
C. If using on board printed antenna: Please do not cover or put anything close to the printed
antenna otherwise the radiation efficiency will be degraded. Also keep clean underneath the
printed antenna area.
D. For Port1, there are 2 options as well, U.FL1 or RF PAD by another jumper capacitor.
E. RF PAD: Ideally, this can bridge the RF signal to the device outside the board. Application board
designer must be caution on the impedance control of the RF pad and 50 Ohm trace at platform
board.
F. DNSA-144 MP version might remove the unused U.FL connector.
Fig. 9: Module Land Footprint [unit:mm]
The information contained herein is the exclusive property of WNC and shall not be distributed, reproduced, or disclosed in whole or in part without prior written permission of WNC.
8/9
Soldering Reflow Profile: Using WNC’s internal SMT line profile. Solder paste: SAC305.
Lead Free Solder
Profile Type Selection
(Sn3.0Ag0.5Cu)
Lead Free
Temperature
<3 ℃/sec
Max. Rising Slope
Profile Parameter
Setting
Time
Soaking Time
140~190 ℃
70~105sec
Wetting Time
217 ℃
70~90sec
Peak Temperature
230~250 ℃
Over Wetting Time
230 ℃
40~60sec
Table 5: Reference soldering profile for customer to mount the module.
4. Regulatory & Environment
Pre-certified FCC
Regulatory Compliance:
Environment policy: All material used inside this module is Lead Free, RoHS compliant.
5. Package Information
80 pcs DNSA-144 * 10 Trays = 800 pcs/SET
800 pcs * 3 SETS(33 Trays) = 2,400 pcs/CARTON
PS Tray Max. Temp is 75℃
6. Order Information
Model
Description
DNSA-144(I)
I-temp standard, SPI, Printing ANT ver.
DNSA-144(I_UFL)
I-temp standard, SPI, U.FL antenna conn. ver.
7. Driver/Utility Installation
The driver should have been installed before the TV is shipped from the manufacturer. You can start
using its network function without installing driver or utility.
The information contained herein is the exclusive property of WNC and shall not be distributed, reproduced, or disclosed in whole or in part without prior written permission of WNC.
9/9

Source Exif Data:
File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.4
Linearized                      : No
Page Count                      : 9
XMP Toolkit                     : XMP toolkit 2.9.1-13, framework 1.6
About                           : 7f7169ea-2293-11e7-0000-b40929846a1.
Producer                        : GPL Ghostscript 9.04
Keywords                        : ()
Modify Date                     : 2017:04:13 18:57:25+08:00
Create Date                     : 2017:04:13 18:57:25+08:00
Creator Tool                    : PDFCreator Version 1.2.3
Document ID                     : uuid:7f7169ea-2293-11e7-0000-b40929846a1%C c..
Format                          : application/pdf
Title                           : DNSA-144 Product Spec & manual - BV - 20170413 _FCC_
Creator                         : tting
Description                     : ()
Author                          : tting
Subject                         : 
EXIF Metadata provided by EXIF.tools
FCC ID Filing: NKR-DNSA144

Navigation menu