Wistron NeWeb XRBH BLE Module User Manual XRBH BLE module V03

Wistron NeWeb Corporation BLE Module XRBH BLE module V03

User Manual_20160824_v1 - User Manual

XRBH User Manual (V0.2) Model Name: XRBH BLE MODULE Description: BLE module compatible This document contains proprietary information which is the property of Wistron NeWeb Corporation and is strictly confidential and shall not be disclosed to others in whole or in part, reproduced, copied, or used as basic for design, manufacturing or sale of apparatus without the written permission of Wistron NeWeb Corporation.
BLE module Delivery Specification V0.3 1Revision History Edition # Reason for revision Issue date V0.1 Initial Document (Draft version) 2016/07/28 V0.2 Add FCC/NCC Label Compliance Statement 2016/07/29 V0.3 Delete Product Overview 2016/08/01
BLE module Delivery Specification V0.3 2 NRF51822 Block Diagram 1
BLE module Delivery Specification V0.3 3Specification CATEGORIESCATEGORIESCATEGORIESCATEGORIES FEATUREFEATUREFEATUREFEATURE Wireless Specificiation Bluetooth® V4.0 (Single Mode/Bluetooth Smart) Frequency 2.402 - 2.480 GHz Max Transmit Power 2dBm Receive Sensitivity -93dBm (Low power mode) Whisper Mode -30 dBm (Transmit) Link Budget 95 dB (@ 1 Mbps) Raw Data Rates 1 Mbps (over the air) Host Interfaces Total 14 lines – multi function UART TX, RX Default 115200, N, ,8, 1 From 1,200 to 115,200bps GPIOs 14 SPI 3 lines I2C 2 lines ADC 6 lines (plus ADC reference) Encryption AES 128 bit using CCM encryption Memory Flash 256KB RAM 32KB Physical Dimensions 16.5mm x 12mm x 2.65mm Clock Management RF 32MHz crystal embedded RTC 32.768KHz crystal embedded Environmental Operating Temperature -10° to +65° C Storage Temperature -10 ˚C to +65 ˚C Miscellaneous Lead Free Lead-free and RoHS compliant
BLE module Delivery Specification V0.3 4Electrical characteristics Low power mode Symbol Minimum Typical Maximum Unit VCC 1.8 1.8 1.8 V LDO mode Symbol Minimum Typical Maximum Unit VCC 1.8 3 3.6 V Power consumption Symbol Description Typical Unit IOFF System off current consumption 0.6 uA IIDLE 3V ON, all blocks idle 2.6 uA Mechanical Dimension
BLE module Delivery Specification V0.3 5
BLE module Delivery Specification V0.3 6PIN Define Pin number Name Function Description 1 P0.02 AIN3 Digital I/O Analog input General purpose I/O 2 ADC input 3 2 P0.01 AIN2 Digital I/O Analog input General purpose I/O 1 ADC input 2 3 P0.03 AIN4 Digital I/O Analog input General purpose I/O 3 ADC input 4 4 P0.05 AIN6 Digital I/O Analog input General purpose I/O 5 UART RXD 5 P0.04 AIN5 Digital I/O Analog input General purpose I/O 4 UART TXD 6 P0.10 Digital I/O General purpose I/O 10 7 VDD Power Power input 8 DEC2 Power Power supply decoupling 9 P0.06 AIN7 AREF1 Digital I/O Analog input Analog input General purpose I/O 6 ADC input 7 ADC Reference voltage 10 P0.07 Digital I/O General purpose I/O 7 TX_IRQ 11 GND Ground Ground 12 GND Ground Ground 13 SWDCLK Digital input HW debug port Flash programming I/O 14 nRESET SWDIO Digital I/O System reset (low active) HW debug port Flash programming I/O 15 P0.16 Digital I/O General purpose I/O 16 16 P0.15 Digital I/O General purpose I/O 15 17 P0.12 Digital I/O General purpose I/O 12 18 P0.11 Digital I/O General purpose I/O 11 19 P0.09 Digital I/O General purpose I/O 9 20 P0.08 Digital I/O General purpose I/O 8 BLE OTA mode, Low active
BLE module Delivery Specification V0.3 721 RF_OUT RF output port for external antenna 22 GND Ground Ground 23 P0.18 Digital I/O General purpose I/O 18 24 P0.20 Digital I/O General purpose I/O 20 25 P0.17 Digital I/O General purpose I/O 17 26 P0.19 Digital I/O General purpose I/O 19 27 P0.14 Digital I/O General purpose I/O 14
BLE module Delivery Specification V0.3 8Recommend Land Pattern
BLE module Delivery Specification V0.3 9Antenna Type Antenna Vendor YAGEO Antenna Type CHIP ANTENNA Antenna PN ANT3216LL12R2400A Antenna Specification Test condition
BLE module Delivery Specification V0.3 10
BLE module Delivery Specification V0.3 113D Raidation Pattern
BLE module Delivery Specification V0.3 12FCC Compliance Statement (1) FCC Label Compliance Statement: This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation. (2) FEDERAL COMMUNICATIONS COMMISSION INTERFERENCE STATEMENT: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: - Reorient or relocate the receiving antenna. - Increase the separation between the equipment and receiver. - Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. - Consult the dealer or an experienced radio/ TV technician for help. (3) End Product Labeling: This transmitter module is authorized only for use in device where the antenna may be installed such that 20 cm may be maintained between the antenna and users. The final end product must be labeled in a visible area with the following: ““““Contains FCC ID: NKR-XRBH””””. The grantee's FCC ID can be used only when all FCC compliance requirements are met. (4) Radiation Exposure Statement This device is intended only for OEM integrators under the following conditions: 1) The antenna must be installed such that 20 cm is maintained
BLE module Delivery Specification V0.3 13between the antenna and users, and 2) The transmitter module may not be co-located with any other transmitter or antenna. As long as 2 conditions above are met, further transmitter test will not be required. However, the OEM integrator is still responsible for testing their end-product for any additional compliance requirements required with this module installed IMPORTANT NOTE: In the event that these conditions can not be met (for example certain laptop configurations or co-location with another transmitter), then the FCC authorization is no longer considered valid and the FCC ID can not be used on the final product. In these circumstances, the OEM integrator will be responsible for re-evaluating the end product (including the transmitter) and obtaining a separate FCC authorization. (5) Radiation Exposure Statement: 1) Any changes or modifications not expressly approved by the grantee of this device could void the user's authority to operate the equipment. 2) This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body. (6) Manual Information To the End User: The OEM integrator has to be aware not to provide information to the end user regarding how to install or remove this RF module in the user’s manual of the end product which integrates this module. The end user manual shall include all required regulatory information/warning as show in this manual
BLE module Delivery Specification V0.3 14本產品符合低功率電波輻射性電機管理辦法 第十二條 ※經型式認證合格之低功率射頻電機，非經許可，公司、商號或使用者均不得擅自變更頻率、加大功率或變更原設計之特性及功能。 第十四條 ※低功率射頻電機之使用不得影響飛航安全及干擾合法通信；經發現有干擾現象時，應立即停用，並改善至無干擾時方得繼續使用。 -前項合法通信，指依電信法規定作業之無線電通信。 -低功率射頻電機須忍受合法通信或工業、科學及醫療用電波輻射性電機設備之干擾。 此模組若安裝於其他平台時，該平台標籤需標明： 此平台內建無線模組
BLE module Delivery Specification V0.3 15Application Note XRBH has embedded 32MHz crystal, which is difference to the Development Kit. In order to let 32MHz crystal works that you can enable it explicitly with the following code: void Clock_settings_32_MHz_func(void) { // Start 32 MHz crystal oscillator. NRF_CLOCK->XTALFREQ = 0x00; NRF_CLOCK->EVENTS_HFCLKSTARTED = 0; NRF_CLOCK->TASKS_HFCLKSTART = 1; // Wait for the external oscillator to start up. while (NRF_CLOCK->EVENTS_HFCLKSTARTED == 0) { \ // Do nothing. } }

Navigation menu