Wistron NeWeb XRBH-1 BLE Module User Manual XRBH 1 BLE module V04
Wistron NeWeb Corporation BLE Module XRBH 1 BLE module V04
User manual
| Download: |  |
| Mirror Download [FCC.gov] | |
| Document ID | 3389570 |
| Application ID | UcXQtQsBqGpAms2dGUpbmw== |
| Document Description | User manual |
| Short Term Confidential | No |
| Permanent Confidential | No |
| Supercede | No |
| Document Type | User Manual |
| Display Format | Adobe Acrobat PDF - pdf |
| Filesize | 29.48kB (368475 bits) |
| Date Submitted | 2017-05-14 00:00:00 |
| Date Available | 2017-05-14 00:00:00 |
| Creation Date | 2017-05-08 13:39:10 |
| Producing Software | GPL Ghostscript 9.04 |
| Document Lastmod | 2017-05-08 13:39:10 |
| Document Title | XRBH-1_BLE_module_User Manual_V04 |
| Document Creator | PDFCreator Version 1.2.3 |
| Document Author: | 10407032 |
XRBH-1 User Manual (V0.4) Model Name: Description: XRBH-1 BLE MODULE BLE module compatible This document contains proprietary information which is the property of Wistron NeWeb Corporation and is strictly confidential and shall not be disclosed to others in whole or in part, reproduced, copied, or used as basic for design, manufacturing or sale of apparatus without the written permission of Wistron NeWeb Corporation. Revision History Edition # V0.1 V0.2 V0.3 V0.4 Reason for revision Initial Document (Draft version) Add Module Dimension Modify FCC Warning Message Modify Max Transmit Power BLE module Delivery Specification Issue date 2017/04/06 2017/04/11 2017/04/12 2017/05/08 V0.4 NRF52832 Block Diagram BLE module Delivery Specification V0.4 Specification CATEGORIES FEATURE Bluetooth® V4.2 (Single Mode/Bluetooth Smart) Frequency 2.402 - 2.480 GHz Wireless Specificiation Max Transmit Power 4dBm +/- 1.0 dBm Receive Sensitivity -96dBm (Low power mode) Raw Data Rates 1 Mbps (over the air) Total 30 lines – multi function UART TX, RX Default 115200, N, ,8, 1 Host Interfaces Encryption Memory Physical From 1,200 to 115,200bps GPIOs 30 SPI 3 lines I2C 2 lines ADC 8 lines (plus ADC reference) AES 128 bit using AES encryption Flash 512KB RAM 64KB Dimensions 14mm x 9.8mm x 2.3mm RF 32MHz crystal embedded RTC 32.768KHz crystal embedded Clock Management Environmental Miscellaneous Operating Temperature -10° to +65° C Storage Temperature -10 ˚C to +65 ˚C Lead Free Lead-free and RoHS compliant BLE module Delivery Specification V0.4 Electrical characteristics DC/DC mode Symbol Minimum Typical Maximum Unit VCC 1.8 3.6 Power consumption Symbol Description Typical Unit IOFF System off current consumption 0.7 uA IIDLE 3V ON, all blocks idle 1.9 uA BLE module Delivery Specification V0.4 Mechanical Dimension BLE module Delivery Specification V0.4 BLE module Delivery Specification V0.4 Recommend Land Pattern BLE module Delivery Specification V0.4 PIN Define Pin number Name Function SWCLK Digital input SWDIO Digital I/O P0.21/RESET Digital I/O P0.22 Digital I/O P0.20/ TRACECLK P0.18/ TRACEDATA[0] Digital I/O Description Serial Wire Debug clock input for debug and programming. Serial Wire Debug I/O for debug and programming. General purpose I/O pin. Configurable as pin reset. General purpose I/O pin. General purpose I/O pin. Trace port clock output. General purpose I/O pin. Digital I/O Trace port output. Single Wire Output. P0.19 Digital I/O General purpose I/O pin. P0.17 Digital I/O General purpose I/O pin. 10 P0.16/ TRACEDATA[1] Digital I/O General purpose I/O pin. Trace port output. 11 P0.11 Digital I/O General purpose I/O pin 12 P0.13 Digital I/O General purpose I/O pin 13 14 15 P0.15/ TRACEDATA[2] NFC2/P0.10 P0.14/ TRACEDATA[3] 16 P0.12 18 NFC1/P0.09 20 P0.07 BLE module Delivery Specification Digital I/O General purpose I/O pin. Trace port output. NFC input NFC antenna connection. Digital I/O General purpose I/O pin Digital I/O General purpose I/O pin. Trace port output. Digital I/O General purpose I/O pin NFC input NFC antenna connection. Digital I/O General purpose I/O pin Digital I/O General purpose I/O pin V0.4 22 P0.08 Digital I/O General purpose I/O pin 24 P0.06 Digital I/O General purpose I/O pin 25 P0.04/AIN2 Digital I/O General purpose I/O pin Analog input SAADC/COMP/LPCOMP input. 26 P0.05/AIN3 Digital I/O General purpose I/O pin. Analog input SAADC/COMP/LPCOMP input. 27 P0.03/AIN1 Digital I/O General purpose I/O pin Analog input SAADC/COMP/LPCOMP input. 29 P0.02/AIN0 Digital I/O General purpose I/O pin Analog input SAADC/COMP/LPCOMP input. 31 P0.31/AIN7 Digital I/O General purpose I/O pin Analog input SAADC/COMP/LPCOMP input. 32 P0.30/AIN6 Digital I/O General purpose I/O pin Analog input SAADC/COMP/LPCOMP input. 33 P0.29/AIN5 Digital I/O General purpose I/O pin Analog input SAADC/COMP/LPCOMP input. 35 P0.26 Digital I/O General purpose I/O pin 36 P0.27 Digital I/O General purpose I/O pin 37 P0.28/AIN4 Digital I/O General purpose I/O pin Analog input SAADC/COMP/LPCOMP input. 38 P0.25 Digital I/O General purpose I/O pin 39 P0.23 Digital I/O General purpose I/O pin. 40 P0.24 Digital I/O General purpose I/O pin. GND Ground Ground VCC Power input +1.7V to +3.6V 1, 17, 19, 21, 23, 34,41,42,43 28,30 BLE module Delivery Specification V0.4 Antenna Type Antenna Vendor WNC Antenna Type PCB ANTENNA Antenna Specification BLE module Delivery Specification 10 V0.4 Test condition BLE module Delivery Specification 11 V0.4 BLE module Delivery Specification 12 V0.4 FCC Compliance Statement (1) (2) FCC Label Compliance Statement: This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation. FEDERAL COMMUNICATIONS COMMISSION INTERFERENCE STATEMENT: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: - Reorient or relocate the receiving antenna. - Increase the separation between the equipment and receiver. - Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. - Consult the dealer or an experienced radio/ TV technician for help. End Product Labeling: The final end product must be labeled in a visible area with the following: “Contains FCC ID: NKR-XRBH-1” ”. The grantee's FCC ID can be used only when all FCC compliance requirements are met. (3) BLE module Delivery Specification 13 V0.4 (4) (5) (6) Radiation Exposure Statement This device is intended only for OEM integrators under the following conditions: 1) this equipment complies with FCC radiation exposure limits set forth for uncontrolled equipment and meets the FCC RF exposure guidelines in Supplement C to DET 65 RF exposure rules. This equipment has very low levels of RF energy that are deemed to comply without testing of specific absorption ration (SAR), and 2) The transmitter module may not be co-located with any other transmitter or antenna. As long as 2 conditions above are met, further transmitter test will not be required. However, the OEM integrator is still responsible for testing their end-product for any additional compliance requirements required with this module installed IMPORTANT NOTE: In the event that these conditions can not be met (for example certain laptop configurations or co-location with another transmitter), then the FCC authorization is no longer considered valid and the FCC ID can not be used on the final product. In these circumstances, the OEM integrator will be responsible for re-evaluating the end product (including the transmitter) and obtaining a separate FCC authorization. Radiation Exposure Statement: 1) Any changes or modifications not expressly approved by the grantee of this device could void the user's authority to operate the equipment. 2) This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. Manual Information To the End User: The OEM integrator has to be aware not to provide information to the end user regarding how to install or remove this RF module in the user’s manual of the end product which integrates this module. The end user manual shall include all required regulatory information/warning as show in this manual BLE module Delivery Specification 14 V0.4 本產品符合低功率電波輻射性電機管理辦法 第十二條 ※經型式認證合格之低功率射頻電機，非經許可，公司、商號或使用者均不得擅自變更 頻率、加大功率或變更原設計之特性及功能。 第十四條 ※低功率射頻電機之使用不得影響飛航安全及干擾合法通信；經發現有干擾現象時，應 立即停用，並改善至無干擾時方得繼續使用。 -前項合法通信，指依電信法規定作業之無線電通信。 -低功率射頻電機須忍受合法通信或工業、科學及醫療用電波輻射性電機設備之干擾。 此模組若安裝於其他平台時，該平台標籤需標明： 此平台內建無線模組 BLE module Delivery Specification 15 V0.4
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.4 Linearized : No Page Count : 16 XMP Toolkit : XMP toolkit 2.9.1-13, framework 1.6 Producer : GPL Ghostscript 9.04 Keywords : () Modify Date : 2017:05:08 13:39:10+08:00 Create Date : 2017:05:08 13:39:10+08:00 Creator Tool : PDFCreator Version 1.2.3 About : 2f74e50b-360c-11e7-0000-4bad3d1a8bc.#.2017-05-08T13:39:10+08:00 Document ID : uuid:2f74e50b-360c-11e7-0000-4bad3d1a8bc+c/. Format : application/pdf Title : XRBH-1_BLE_module_User Manual_V04 Creator : 10407032 Description : () Author : 10407032 Subject :EXIF Metadata provided by EXIF.tools