Wonde Proud Technology WPBT100NX BLUETOOTH GPS RECEIVER User Manual USERS MANUAL
Wonde Proud Technology Co., Ltd. BLUETOOTH GPS RECEIVER USERS MANUAL
USERS MANUAL
*** USER’S MANUAL *** FCC ID : SRKWPBT100NX The Federal Communication Commission Statement This equipment has been tested and found to comply with the limits for a Class B Digital Device, pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instruction, may cause harmful interference to radio communication. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of more of the following measures: - Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced Radio/TV technician for help. Use only shielded cables to connect I/O devices to this equipment. You are cautioned that change or modifications not expressly approved by the party responsible for compliance could void your authority to operate the equipment. THIS DEVICE COMPLIES WITH PART 15 OF THE FCC RULES. OPERATION IS SUBJECT TO THE FOLLOWING TWO CONDITIONS: (1) THIS DEVICE MAY NOT CAUSE HARMFUL INTERFERENCE, AND (2) THIS DEVICE MUST ACCEPT ANY INTERFERECE RECEIVED, INCLUDING INTERFERENCE THAT MAY CAUSE UNDESIRED OPERATION. 1. This device may not cause harmful interference and 2. This device must accept any interference received, including interference that may cause undesired operation. GPS Bluetooth Receiver User’s Guide Bluetooth GPS Receiver User’s Guide Bluetooth GPS Receiver User’s Guide Table of Contents 1. 2. 3. 4. 5. 6. Read Me First………………………………………………………………………………….. p.3 Box Contents…………………………………………………………………………………… p.3 Getting Started…………………………………………………………………………………. p.3 Hardware Description…………………………………………………………………………. p.7 LED Indicator…………………………………………………………………………………... p.8 Specification……………………………………………………………………………………. p.9 Bluetooth GPS Receiver User’s Guide 1. Read Me First 1. The battery must be charged for at least 8 hours for the ‘INITIAL’ use. The LED1 (ORANGE) will turn off after 3 hours’ charging, please keep on charging for 5 more hours. Thereafter, for each time’s battery charging please fully charge for 3 hours. 2. We strongly recommend that remove the battery if the device will not be used for over 2 weeks. Do not remove the battery within 2 weeks. 3. For fast data tracking purpose staying still before get fixed is recommended. (FIX then GOES!!) 4. Please note that the device will only receive the signal under the open sky. In this case, putting the device under the windshield is recommended. 2. Box Contents 1. 2. 3. 4. 5. 6. GPS Bluetooth Receiver Lithium-ion rechargeable battery Car charger Power adapter Document CD Anti-Slip Rubber Pad 3. Getting Started 1. Install the battery 2. Turn on the GPS Bluetooth receiver. Press the power button for 1 second or until the LED2 (GPS Fix Status) turns into RED and LED4 (Bluetooth Status) turns into Blue. 3. Activate Bluetooth function of your PDA / PC Prior to activating the Bluetooth function of your PDA / PC, please make sure the device is equipped with Bluetooth function, and the driver software has been installed. 4. Activate Bluetooth Manager & Established New Connections. Illustrations using HP 2100 PDA as follows: 1. 2. 3. 4. First, find the device with which you wish to establish connection. Open “Bluetooth Manager” on your pocket PC. Press “New”. Press "Connect”. Bluetooth GPS Receiver User’s Guide BTGPS Click here Click here to select installation Bluetooth GPS Receiver User’s Guide BTGPS **** Enter Pass Key "0000", then Press “Enter” Enter key BTGPS BTGPS Click here Click here Bluetooth GPS Receiver User’s Guide Connection established BTGPS: SPP slave The connection between GPS Bluetooth receiver and PDA has been successfully established 5. Turn off the GPS Bluetooth receiver Press the power button for 1 second, all LEDs will goes off. We recommend that close the E-map before turning off the GPS Bluetooth receiver, in order to avoid any possible PDA /PC freeze. Bluetooth GPS Receiver User’s Guide 4. Hardware Description LED3: Power Status LED1: Charging Status Power Button (GREEN) (ORANGE) LED2: GPS Fix Status Charge Socket (RED) Slip-Resistant LED4: Bluetooth Status (BLUE) Bluetooth GPS Receiver User’s Guide 5. LED Indicator Power on: LED1: Charging Status LED2: GPS Fix Status N/A LED3: Power Status LED4: Bluetooth Status N/A Blue Blinking quickly for the first 5 sec., then blinking slowly (in paring mode) LED3: Power Status LED4: Bluetooth Status N/A Blue Blinking quickly Red (Keep ON) GPS not fixed yet! GPS get fixed/Bluetooth connected: LED1: Charging Status LED2: GPS Fix Status N/A Red Blinking - Low battery: LED3 (GREEN) blinking for every 1 second - Charging: LED1 (ORANGE) ON; the GPS Bluetooth receiver will automatically turns on - Battery is fully charged: LED1 (ORANGE) turns off - GPS Bluetooth receiver will automatically turns off if no Bluetooth connection after 10 minutes Low Battery Charging GPS Bluetooth operates on OS with Bluetooth function that supports SPP In order to avoid any unexpected problem, DO NOT attempt to change the default baudrate Bluetooth GPS Receiver User’s Guide 6. Specification GPS Features Datum Chipset SiRF Star III WGS-84 Frequency L1, 1575.42MHz Dynamic Conditions C/A Code 1.023MHz chip rate Altitude <18,000 m (60,000feet) Channels Supports 20 channels Velocity <515 m/s (1000 knots) Antenna (Internal) Built-in low noise antenna Acceleration <4G Motional Jerk 20m/sec3 max. Sensitivity Interface To – 159dBm Tracking, Superior Urban Canyon Communication Protocol: Communicate with host Performance platform via Bluetooth (class 2) serial port profile Time to First Fix (TTFF) Bluetooth communication distance 10meters (Typical) Cold Start 42 sec, average GPS Protocol: Default: NMEA-0183 - GGA, GSA, GSV, Warm Start 38 sec, average RMC, VTG Hot Start 1 sec, average Data bit: 8, stop bit: 1 (Default) Reacquisition 0.1 sec Device Size and Weight Update rate 1 Hz (max.) 77.05 (L) X 46.10 (W) X 19.50 (H) mm 3.03 (L) X 1.81 (W) X 0.77 (H) inch Accuracy Position 5 – 25m CEP without SA 59g (battery included) Velocity 0.1m/sec, without SA Accessories Time 1μs synchronized to GPS time Car charger (12V in, 5V output) AC adaptor (5.3V output, 500mA) Power Built-in rechargeable 1100mAh Li-ion battery and 5V DC input Operation Current Operation Time Charging time <45mA (Typical) 24hrs, fully charged, in continuous mode Environmental Characteristics Operating Temperature - 10°C to + 60°C Storage Temperature - 20°C to + 85°C 3.0hrs. (Typical) All specifications are subject to change without notice
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.4 Linearized : No Encryption : Standard V1.2 (40-bit) User Access : Print, Fill forms, Extract, Assemble, Print high-res Create Date : 2007:03:27 17:36:33+08:00 Modify Date : 2007:10:08 16:42:45+08:00 Source Modified : D:20070410033229 Tagged PDF : Yes Producer : Acrobat Distiller 7.0 (Windows) Mod Date : 2007:10:08 16:42:45+08:00 Creation Date : 2007:03:27 17:36:33+08:00 Author : abcde Headline : Creator Tool : Acrobat PDFMaker 7.0 for Word Metadata Date : 2007:10:08 16:42:45+08:00 Keywords : Document ID : uuid:cabd4468-5c37-451a-84a9-4eb45053d144 Instance ID : uuid:e911be10-060e-4a82-86e4-b34a053b093c Version ID : 16 Format : application/pdf Title : Microsoft Word - GPS Bluetooth Receiver User's Guide Creator : abcde Subject : Page Count : 11 Page Layout : OneColumn Has XFA : NoEXIF Metadata provided by EXIF.tools