Wonde Proud Technology WPBT77X BLUETOOTH GPS RECEIVER User Manual USERS MANUAL

Download:
Mirror Download [FCC.gov]
Document ID	499274
Application ID	kgSLLigRQIT5wDbQz2wJ/A==
Document Description	USERS MANUAL
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	134.36kB (1679538 bits)
Date Submitted	2004-12-21 00:00:00
Date Available	2004-12-21 00:00:00
Creation Date	2004-12-16 09:59:46
Producing Software	Acrobat Distiller 5.0.5 (Windows)
Document Lastmod	2004-12-16 09:59:46
Document Title	USERS MANUAL

*** USER’S MANUAL ***
FCC ID : SRKWPBT77X
The Federal Communication Commission Statement
This equipment has been tested and found to comply with the limits for a Class B Digital Device,
pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment generates, uses and can
radiate radio frequency energy and, if not installed and used in accordance with the instruction, may
cause harmful interference to radio communication.
However, there is no guarantee that
interference will not occur in a particular installation.
If this equipment does cause harmful
interference to radio or television reception, which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the interference by one of more of the following
measures: -
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver
is connected.
Consult the dealer or an experienced Radio/TV technician for help.
Use only shielded cables to connect I/O devices to this equipment. You are cautioned that change
or modifications not expressly approved by the party responsible for compliance could void your
authority to operate the equipment.
THIS DEVICE COMPLIES WITH PART 15 OF FCC RULES. OPERATION IS SUBJECT TO THE
FOLLOWING TWO CONDITIONS: 1.
This device may not cause harmful interference and
2. This device must accept any interference received, including interference that may cause
undesired operation.
Bluetooth GPS Receiver
Contents
1. INTRODUCTION..........................................................................................................................1
1.1. OVERVIEW ...............................................................................................................................1
1.2. MAIN FEATURES.......................................................................................................................1
2. TECHNICAL SPECIFICATIONS .................................……............................................................ 2
3. OPERATION AND TEST.................................................................................................................3
3.1. HARDWARE DESCRIPTION........................................................................................................4
3.2. WHAT DO YOU GET IN THE BOX?..............................................................................................5
3.3. SOFTWARE INSTALL .................................................................................................................5
4. APPENDIX A TEST REFERENCE FOR ONLY..............................................................................10
1. Introduction
1.1. Overview
The BT-77 Bluetooth GPS receiver is a Global Position System Receiver with Bluetooth wireless technology.
This BT GPS receiver allows you to receive GPS data on mobile handhelds wirelessly. By sending GPS
position data over Bluetooth, you can position the receiver for the best possible reception all without wires.
The advent of Bluetooth GPS receiver will become the next level of GPS receivers. The BT GPS receiver integrates
Bluetooth module into GPS device. It shows the high performance, low power consumption,
easily portable, rechargeable & removable battery function and wireless data transmission. If you have a Pocket
PC or other portable devices enabled with Bluetooth function, for example ASUS-620, iPAQ 2210, HP
and Palm , you can take advantage of your device’ s Bluetooth capability to wirelessly add GPS positioning
technology. When you choose suitable navigation software, you can apply to personal, vehicle tracking,
and marine navigation. If you use this Bluetooth GPS receiver, you will ignore the messy cords and antenna
and add the portability of your Pocket PC. In addition, This Bluetooth GPS receiver can change the
exhausted battery to full battery like battery of mobile phone.
1.2.
‹
‹
‹
‹
‹
‹
‹
‹
‹
‹
‹
Main Features
16 Channels “All-In-View” Tracking
Cold/Warm/Hot Start Time: 45/38/10 Seconds : Reacquisition Time: 0.1 seconds
Support Standard NMEA-0183 at 9600 bps baund rate
Compatible with Bluetooth devices with Serial Port Profile (SPP)
Small, sleek, and lightweight design easily fits in your hand
Two LEDs at the top of the device show Bluetooth and GPS. & On/off push button
Fleet management/Asset tracking
Personal/Portable Navigation (PDA, Pocket PC etc.)
Location Based Services enabled devices
Ultra low power-up to 16 hours after fully charged (850mA Li-ion Battery)
High sensitivity-147dBm Integrated GPS receiver, Active antenna, and Bluetooth transceiver
2.TECHNICAL SPECIFICATIONS
General
GPS technology
NEMERIX GPS module
Frequency
L1, 1575.42 MHz
C/A code
1.023 MHz chip rate
Channels
16 channels all in view tracking
Antenna (internal)
Built-in low noise
External Antenna Port active MMCX antenna
Sensitivity
to -147 dBm tracking, superior urban canyon
performance
Accuracy
Position
3 meters CEP (50%),
without SA (horizontal)
7 meters (90%)
0.1 meters/second,
without SA
±100 ns synchronized to
GPS time
Velocity
Time
Datum
Interface
Communication protocol
Communicate with host platform via
Bluetooth (Class 2) serial port profile
Bluetooth communication distance 10M. Typ.
GPS protocol
Default: NMEA-0183 (V3.01)
—GGA, GSA, GSV, RMC,
the update interval 1 second (Default)
Band rate 9600 bps(Data bit : 8,stop bit : 1)
Power
Built-in rechargeable 850mA/h Li-ion
battery and 5V DC input charging circuit
Operation current
45mA (Typical)
Operation time
20hrs, after fully charged, in
Continuous mode
Charging time
2.5hrs. (Typical)
Device Size
WGS-84 (or by demanded)
Accessories
Acquisition Rate
Cold start
Warm start
Hot start
Reacquisition
Dynamic Conditions
Altitude
Velocity
Acceleration
Motional Jerk
3. Operation
and Test
45 sec, average
38 sec, average
10 sec, average
100ms, average
81(L) x 44(W ) x 20(H) mm
3.2 (L)x 1.75 (W) x 0.79 (H) inch
AC adaptor(5.3V output ,500mA)
Environmental
Operating Temperature
-20°C to + 60°C
Relative Humidity 5% to 90% non-condensing
<18,000 meters
<515 meters/second
< 4g
20 meters/second
3.1. Hardware Description
LED2
External
Power Socket
Power
LED1
The Bluetooth GPS has two LED light which each has three colors.
One is GPS (LED2) & Charge status (LED 1) . The status table of LED shows as follows:
LED
Color
Status
RED
Power On
GREEN
Battery is charging until full
LED 1
GREEN (Flashing)
Low Power
BLUE ( Flash quickly)
Detecting satellites , GPS position not fix.
LED 2
BLUE ( Flash slowly)
GPS Position fix , Navigation
3.2. What do you get in the box?
9 BT GPS receiver
9 A Adapter , 5.3V/500mA output
9 A user’s manual ( CD disc )
9 A Li-Polymer rechargeable battery 850mAh
3.3.1 Software Install - Pocket PC CE
iPAQ Bluetooth fuction setup with Pocket PC software
 On the client, make sure the Bluetooth device is available.
<1> Tap Bluetooth pop-up menu,
Turn Bluetooth ON and select Bluetooth manager.
<2> Established new connection , click .
<3> Select “Explore a Bluetooth device “ ,Then,
<4> Tap device , then click “ next “ .
turn Bluetooth GPS on before going next step .
<5>Choose BT_GPS , click it.
<6> Enter passkey “ 0000”. Enter.
<7> Select “SPP slave “ , click “Next” Ш“Finish “ And BT-GPS connection Established successfully.
<9> Tap “ Bluetooth icon “ again ,
and select “ Bluetooth setting “.
3.3.2 Software setup – Navigator (PaPaGo! 5)
<9> Tap “ Serial port “ , Enable service first , then
, set up outbound COM port to be “8”.
<1.> Find Navigator software in programs ,
and tap PaPaGo! 5 Navigator
<2.> Tap “tools” and select “setup”.
 The Navigator of map is Chinese version ,and shows as follow. The English version should be similar with Chinese.
<3.> Tap “GPS” table , as following setup. <4.> Return to PaPaGo main screen .
tap “tools” and select “GPS” Ш “ GPS position “
<5.> GPS position fixed ans start navigating.
Appendix A Test Reference for Only
PC Bluetooth Setup with Widcomm BTW
This software does belong to copyright reserved of Widcomm company and you have to
get the authorized software to use it. The follow method is only for reference.
The Bluetooth Serial Port service allows two Bluetooth devices to establish a wireless
connection through virtual communications ports and then use that connection as if it
were a hardwired serial cable between the devices.
To establish a Bluetooth serial port connection:
Connections are initiated from the client:
<1> On the client, in the Folders pane of My Bluetooth Places, select Entire Bluetooth Neighborhood.
<2> In the right pane of Entire Bluetooth Neighborhood, right-click anywhere except on
a device name and select Refresh from the pop-up menu.
<3> In the Folders pane of My Bluetooth Places, right-click the server you want to establish a
connection with and select Discover Available Services from the popup menu to update the available
services list. The available services will be displayed in the right pane of My Bluetooth Places.
<4> In the right pane of My Bluetooth Places, double-click Bluetooth Serial Port. A dialog box appears
that contains the communications port number assigned to this connection by the client. The
application that will use this connection must be configured to send data to this port.
To close a Bluetooth serial port connection , Connections are normally closed from the client:
.. On the client, in the Folders pane of My Bluetooth Places, select (highlight) the device that is
providing the Bluetooth Serial Port service.
.. In the right pane of My Bluetooth Places, right-click Bluetooth Serial Port and then select
Disconnect Bluetooth Serial Port from the pop-up menu.

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.3
Linearized                      : No
Create Date                     : 2004:12:16 09:59:46+08:00
Modify Date                     : 2004:12:16 09:59:46+08:00
Page Count                      : 12
Creation Date                   : 2004:12:16 01:59:46Z
Mod Date                        : 2004:12:16 01:59:46Z
Producer                        : Acrobat Distiller 5.0.5 (Windows)
Metadata Date                   : 2004:12:16 01:59:46Z

EXIF Metadata provided by EXIF.tools