Wonders Technology DS-1060 BLUETOOTH CLOCK RADIO WITH DUAL ALARM User Manual USERS MANUAL

Wonders Technology Co., Ltd. BLUETOOTH CLOCK RADIO WITH DUAL ALARM USERS MANUAL

USERS MANUAL

Plug the included AC/DC power adapter into the DC POWER INPUT on the unit and an AC power outlet to power the dock.DC IN 5VFM ANT. AUX IN DC OUTPUT 5VAL 1 / AL 2 SLEEP CLK SET/MEM SOURCEVOLUMETUNING++POWERTALK/END PAIRSNOOZE/DIMMERUSB Charging PortICB352BWarning: Changes or modications to this unit not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to  try to correct the interference by one or more of the following measures:•  Reorient or relocate the receiving antenna.•  Increase the separation between the equipment and receiver.•  Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.•  Consult the dealer or an experienced radio/TV technician for help.•  The apparatus shall not be exposed to dripping or splashing and that no objects lled with liquids, such as vases, shall be placed on apparatus. L’appareilnedoitpasêtreexposéauxécoulementsouauxéclaboussuresetaucunobjetnecontenantdeliquide,telqu’unvase,nedoitêtreplacésurl’objet.•  Main plug is used as disconnect device and it should remain readily operable during intended use. In order to disconnect the apparatus from the mains completely, the mains plug should be disconnected form the mains socket outlet completely. Laprisedusecteurnedoitpasêtreobstruéeoudoitêtrefacilementaccessiblependantsonutilisation.Pourêtrecomplètementdéconnectédel’alimentationd’entrée,laprisedoitêtredébranchéedusecteur.•  Battery shall not be exposed to excessive heat such as sunshine, re or the like. Lespilesnedoiventpasêtreexposéesàdefortechaleur,telqu’àlalumièredusoleil,aufeuouautreschosesdesemblable.•  Caution marking is located at the rear or bottom of the apparatus. Attentionmarquageestsituésurlepaneauarrièreouinférieurdel’unité.•  The marking information is located at the rear or bottom of apparatus. Lemarquageestsituésurlepaneauarrièreouinférieurdel’unité.1.  Read these Instructions.2.  Keep these Instructions.3.  Heed all Warnings.4.  Follow all instructions.5.  Do not use this apparatus near water.6.  Clean only with a dry cloth.7.  Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions.8.  Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including ampliers) that produce heat.9.  Do not defeat the safety purpose of the polarized or grounding - type plug. A polarized plug has two blades with one wider than the other. A grounding type plug has two blades and a third grounding prong. The wide blade or the third prong are provided for your safety. When the provided plug does not t into your outlet, consult an electrician for replacement of the obsolete outlet.10.  Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point where they exit from the apparatus.11.  Only use attachments/accessories specied by the manufacturer.12.  Use only with a cart, stand, tripod, bracket, or table specied by the manufacturer, or sold with the apparatus. When a cart is used, use caution when moving the cart/apparatus combination to avoid injury from tip-over. Unplug this apparatus during lightning storms or when unused for long periods of time.13.  Refer all servicing to qualied service personnel. Servicing is required when the apparatus has been damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.• CAUTION: TO PREVENT ELECTRIC SHOCK, MATCH WIDE BLADE OF PLUG TO WIDE SLOT, FULLY INSERT.• WARNING:To reduce the risk of re or electric shock, do not expose this apparatus to rain or moisture.• AVERTISSEMENT: Pour réduire le risque d’incendie ou de choc électrique, ne pas exposer cet appareil sous la pluie et l’humidité.• CAUTION: Use of controls or adjustments or performance of procedures other than those specied may result in hazardous radiation exposure.• WARNING: Changes or modications to this unit not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.• WARNING: Do not place the unit on top of any soft, porous, or sensitive surfaces to avoid damaging the surface. Use a protective barrier between the unit and surface to protect the surface.• WARNING: Use of this unit near uorescent lighting may cause interference regarding use of the remote. If the unit is displaying erratic behavior move away from any uorescent lighting, as it may be the cause.• CAUTION:Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type.• PRÉCAUTION:Dangerd’explosionsilespilessontremplacéesdefaçonincorrect.Remplacerlespilesseulementparlemêmetypedepileoul’équivalent.• WARNING: There is a danger of explosion if you attempt to charge standard Alkaline batteries in the unit. Only use rechargeable NiMH batteries.• WARNING: The remote control’s button cell battery contains mercury. Do not put in the trash, instead recycle or dispose of as hazardous waste• WARNING:Lithium batteries, like all rechargeable batteries are recyclable and should be recycled or disposed of in normal household waste. Contact your local government for disposal or recycling practices in your area. They should never be incinerated since they might explode.• WARNING: Shock hazard - Do Not Open.• AVIS:RISQUEDECHOCÉLECTRIQUE-NEPASOUVRIRMains plug is used as disconnect device and it should remain readily operable during intended use. In order to disconnect the apparatus from the mains completely, the mains plug should be disconnected form the mains socket outlet completely. Laprisedusecteurestutilisépourdéconnecterlesystème.Laprisedusecteurnedoitpasêtreobstruéeoudoitêtrefacilementaccessiblependantsonutilisation.Pourêtrecomplètementdéconnectédel’alimentationd’entrée,laprisedoitêtredébranchéedusecteur.Do not mix old and new batteries.Do not mix alkaline, standard (carbon-zinc), or rechargeable (ni-cad, ni-mh, etc) batteries.Nomezclebateríasviejasynuevas.Nomezclebateríasalcalinas,estándar(carbono-zinc)orecargables(ni-cad,ni-mh,etc.).WARNING: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO USER-SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.ATTENTIONRISQUE D' ÉLECTROCUTIONNE PAS OUVRIRCAUTIONRISK OF ELECTRIC SHOCKDO NOT OPENThe exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance.This symbol indicates that this product incorporates double insulation between hazardous mains voltage and user accessible parts.The lightning ash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated “dangerous voltage” within the product’s enclosure that may be of sufcient magnitude to constitute a risk of electric shock to persons.IMPORTANT SAFETY INSTRUCTIONSIntroduction and SetupFCC WarningsPowerThe battery backup is intended for short power outages only. The clock radio’s primary functions cannot run off of the battery backup alone.Requires a CR2025 battery (pre-installed)LITHIUM BATTERYCR 20253VPUSHOPENLITHIUM BATTERYCR 20253VCR2025PUSHOPENBattery BackupAdditional WarningsWARNINGS AND PRECAUTIONSFor Warranty Information and the most up-to-date version of this User’s Guide, go to www.iLiveElectronics.com  Customer Service: 1-888-999-4215Email Support: prodinfo@dpiinc.com, Email Parts: partsinfo@dpiinc.comCopyright © 2012 Digital Products International (DPI, Inc.) All other trademarks appearing herein are the property of their respective owners. Specications are subject to change without notice.USER’S GUIDEV:557-01ChargingCharging a Device1.  Make sure the unit is plugged into the wall.2.  Using the appropriate USB charging cable (not included), connect one end to the device and the other to the USB Charging Port on the unit.Refer to the user’s manual for your specic device for manufacturers required charging amperage as well as determining the appropriate cable for your device before charging.3.  The device will now charge.DC IN 5VFM ANT. AUX IN DC OUTPUT 5VTuning +/-Press to tune the radio in FM Radio Mode.Press and hold to search for the next available frequency.PowerPress to turn the unit on or off.Clock Set/MemIn off mode, press to set the clock.In FM Radio mode, press and hold to begin saving the current radio station as a preset.SourcePress to switch between FM Radio, Bluetooth and Line In modes.VolumePress to adjust the volume.PairPress and hold to begin pairing a Bluetooth device. Talk/End/Play/PausePress to answer or end a call.Press to play or pause a connected Bluetooth device.Alarm 1/Alarm 2Press to begin setting the alarms.SleepIn FM Radio mode, press to begin setting the sleep timer.Snooze/DimmerPress to delay the alarm.Press to adjust the brightness of the display.Line InBluetooth Clock radio with Dual Alarm
1.  If powered on, press the Power button to turn the unit off.2.  Press the Clock Set/Mem button.3.  Press the Tuning+/- buttons to adjust the hour.The PM indicator will light when the hour is set in the PM.4.  Press the Clock Set/Mem button.5.  Press the Tuning+/- buttons to adjust the minute.6.  Press the Clock Set/Mem button again to nish setting the time.1.  If powered on, press the Power button to turn the unit off.2.  Press and hold the Al1 or Al2 button until the display begins to blink, then release the button.3.  Press the Tuning+/- buttons to adjust the minute.The PM indicator will light when the hour is set in the PM.4.  Press the Tuning+/- buttons to adjust the minute.5.  Press the Al1 or Al2 buttons to switch between Radio and Beep.6.  Once the set alarm time is reached, the alarm will sound.To set the other alarm, follow the above steps and choose the alarm not currently set. 1.  Power on the unit by pressing the Power button. 2.  Press the Source button to switch to FM Radio mode.3.  Press the Tun+ and Tun-buttons to adjust the radio to the desired frequency. 4.  Press and hold the Tun+ and Tun- buttons to search for the next available frequency.5.  Press the Vol+/- buttons to adjust the volume.6.  Turn the radio off by pressing the Power button. Clock and Sleep TimerAlarmRadioSetting the Clock1.  Power on the unit by pressing the Power button. 2.  Press the Source button to switch to FM Radio mode.3.  Press the Sleep button repeatedly to set the sleep timer ( 15, 30, 45, 60, 75, 90  min or OFF ).4.  Once the set sleep time has expired the clock radio will automatically power off.Setting the Sleep TimerSetting the Alarm1.  Follow the instructions for Setting the Alarm.2.  Press the Al1 or Al2 buttons repeatedly until the indicator is no longer lit.Cancelling the AlarmAfter the alarm sounds:Press the Sleep button to delay the alarm for several minutes.ORPress the Power button to turn the alarm off until the set alarm time is reached again.Snooze and Alarm ResetTuning the AM or FM Radio1.  Follow the instructions for Tuning the Radio and Saving a Station as a Preset.2.  Press the Clock Set/Mem button. 3.  Press the Tun+ and Tun-buttons to cycle through preset radio stations.Tuning to a Preset Radio StationAdjust the position of the FM Antenna to improve FM radio reception.Radio ReceptionTo download this User’s Guide in English, Spanish, or French, or to get answers to frequently asked questions, visit the support section  at: www.iLiveElectronics.comPara descargar este Manual del Usuario en inglés, español y francés, o para obtener respuestas a preguntas frecuentes, visite la sección de apoyo en www.iLiveElectronics.comPour télécharger ce guide de l’utilisateur en anglais, espagnol ou français, ou pour obtenir des réponses à des questions fréquemment posées, consultez la rubrique d’assistance sur www.iLiveElectronics.comInternational SupportFor Warranty Information and the most up-to-date version of this User’s Guide, go to www.iLiveElectronics.com  Customer Service: 1-888-999-4215Email Support: prodinfo@dpiinc.com, Email Parts: partsinfo@dpiinc.comCopyright © 2012 Digital Products International (DPI, Inc.) All other trademarks appearing herein are the property of their respective owners. Specications are subject to change without notice.Requires a 3.5mm audio cable (not included)1.  Connect a 3.5mm audio cable to the Line In on the unit and an audio output on an MP3 player or other audio source.2.  Use the native controls on the connected MP3 player or other audio source to play and control audio played through the clock radio.Line InUsing the Line InBluetooth SetupPairing a Bluetooth Device for the First Time1.  Power on the unit by pressing the Power button. 2.  Press the Source button to switch to Bluetooth mode.Bluetooth mode is indicated by “BT” on the display.“PAIR”will ash slowly on the display.3.  Press and hold the Pair button until “PAIR” ashes quickly.When pairing, remain within 3 feet of the unit.4.  Using the native controls on your Bluetooth device, select the “ICB352” in your Bluetooth settings to pair.If your device requests a password, enter the default password “ 0 0 0 0 ”. Refer to the user’s manual for your specic device for instructions on pairing and connecting Bluetooth devices.5.  When successfully paired and connected, the display will show “BT”.After initial pairing, the unit will stay paired unless unpaired manually by the user or erased due to a reset of the device. If your device should become unpaired or you nd it is unable to connect, repeat the above steps.  Note: ICB352 can store up to 8 devices. The ninth paired device will replace the rst stored device in the unit’s memory. The tenth device paired will replace the second stored unit and so on.1.  Follow the instructions in Pairing a Bluetooth Device.2.  When a call is received, a ringtone will sound through the speakers.3.  Press the Play/Pause/Talk/End button to accept the call or accept the call with the native controls on the connected device.4.  The incoming call received through the device will now be heard through the speakers.5.  To end the call, press the Play/Pause/Talk/End button or end the call using the native controls on the connected device.1.  Follow the instructions for Pairing a Bluetooth Device.2.  Use the native controls on the connected Bluetooth Device to select a track.3.  To play or pause the selected track, use the native controls on the connected Bluetooth Device or press the Play/Pause/Talk/End button.4.  Audio played through the connected Bluetooth device will now be heard through the speakers.  Playing Audio WirelesslyUsing the SpeakerphoneSaving a Station as a Preset1.  Follow the instructions for Tuning the FM Radio.2.  Tune to the desired station.3.  Press and hold the Clock Set/Mem button.4.  Press the Tun+/- buttons to choose the preset number.5.  Press and hold the Clock Set/Mem button to save the station as a preset.Up to 20 stations may be saved as presets.
FCC warning:This device complies with Part 15 of the FCC Rules. Operationis subject to the following two conditions: (1) this devicemay not cause harmful interference, and (2) this device mustaccept any interference received, including interferencethat may cause undesired operation.The antenna used for this transmitter must be installed toprovide a separation distance of at least 20 cm from allpersons and must not be co-located or operated in conjunctionwith any other antenna or transmitter.

Navigation menu