Wooyoung Telecom HL500M LCD Monitor User Manual
Wooyoung Telecom Co., Ltd. LCD Monitor
User Manual
User’s Manual WOO YOUNG Telecom CO.,LTD. FCC STATEMENT This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, with can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one more of the following measures: - Reorient or relocate the receiving antenna. - Increase the separation between the equipment and receiver. - Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. - Consult the dealer or an experienced radio/TV technician for help. - Only shielded interface cable should be used. Finally, any changes or modifications to the equipment by the user not expressly approved by the grantee or manufacturer could void the users authority to operate such equipment. Contents ・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・ ・・・・・・・・・・・・・・・・・・・・・・・・・ ・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・ ・・・・・・・・・・・・・・・・・・・・・・・・ ・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・ 1. Before Setting up Brief Specification of LCD Monitor Precautions Instruetion for Cleaning the Monitor 2. Items 3. Setting up the LCD monitor ・・・・・・・・・・・・・・・・・・・・・・・・・ ・・・・・・・・・・・・・・・・・ 10 ・・ 11 ・・・・・・・・・・・・・・・・・・・・・・・・・・・ 12 ・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・ 13 ・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・ 13 Where is a good place to position the monitor? How to connect the power cord and the several cables to the LCD monitor. Connecting Your LCD Monitor Plug & Play 10 Warm-up Time 4. Adjusting The Monitor ・・・・・・・・・・・・・・・・・・・・・・・・・・・・・ 14 ・・・・・・・・・・・・・・・・・・・・・・・・・・・ 14 ・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・ 14 ・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・ 16 ・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・ 17 ・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・ 17 ・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・ 18 The Function Control Buttons How to use the Hot Key. Main OSD Menu COLOR USER COLOR OSD FUNCTION VIDEO ・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・ 19 Color ・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・ 20 TV ・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・ 21 ・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・ 21 Channel 5. Appendix ・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・ 22 Appendix A. Display Modes ・・・・・・・・・・・・・・・・・・・・・・・・・ 22 Appendix B. 15-pin D-Sub Connector ・・・・・・・・・・・・・・・・・・・・・ 23 ・・・・・・・・・・・・・・・・・・・・・・・・・・・・ 24 ・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・ 25 DPMS Power Saving Mode 6. Troubleshooting 1 Before setting up This is 15.0 inch TFT-LCD monitor. Before setting up the LCD Monitor, please read this manual to help your understanding of the LCD Monitor. Brief Specification of LCD Monitor ● Resolution : 15.0 inch XGA (1024 X 768@75Hz) ● Color display : 16,777,216 colors ● DPMS (Display Power Management Signaling) ● OSD (On Screen Display) ● Auto Configuration : Hot key ● DDC 1/2B : Plug & Play Notice According to PC system, DDC 1/2B may not be supported. If you meet Error message,check your video card which compatibility with DDC. If you eant to know more information, please contact our service center. Precautions Warning : The following information will help you avoid the risk of electric shock, serious injury, and death. Power cord AC outlet Plug the power cord into a properly grounded outlet. There is the risk of electric shock. If you hear a noise or smell smoke from the computer or adaptor, unplug the power cord immediately, and call the service center. There is the risk of electric shock or fire. Do not overload an electrical outlet with too many devices. There is the risk of fire. Do not unplug from the outlet by pulling the power cord or when your hands are wet. There is the risk of electric shock and fire. Do not bend the power cord excessively or place heavy objects on it. Keep children and pets away from the power cord as they may damage the power cord. There is the risk of electric shock and fire. Do not use a damaged power cord or plug. Make sure the plug fits snugly into the outlet. There is the risk of electric shock or fire. Do not expose the monitor to the direct sun light. Keep the monitor away from high temperature, humidity, and dust. ■Operating environment=0~40degrees Celsius ■Operating environment=30~80relative humidity. Do not block the fan louvers. There is the risk of fire or damage to the monitor. Do not allow any object or liquid to enter inside the monitor. There is the risk of electric shock, fire, or damage to the monitor. Do not attempt to disassemble, fix, or modify the monitor. There is the risk of electric shock or fire. Caution : The following information will help you avoid the risk of minor or moderate injury, or damage to the monitor. Use a proper voltage/current level indicated Do not clean the LCD with abrasive chemicals. There is the risk of damage to the LCD. Do not scratch and damage the LCD with sharp objects. Keep the monitor away from objects and electrical appliances that may generate electromagnetic fields. Place the monitor on a flat, stable surface. The monitor may fall and there is the risk of damage or injury Unplug the power cord when the monitor is not in use for a prolonged period of time. Instruction for Cleaning the Monitor Make sure the power cord is unplugged. Do not spill or pour liquid on the monitor. ● Cleaning the LCD panel 1. Use a clean, soft cloth to wipe off dust from the LCD. 2. If still not clean, wipe the LCD with a clean soft cloth with a small amount of glass cleaner? without alcohol or ammonia. ● Cleaning other parts of the monitor 1. Use a clean, soft cloth to wipe off dust from the monitor. 2. If still not clean, wipe the LCD with a clean soft cloth with a small amount of glass cleaner? without alcohol or ammonia. ● Caution Do not use alcohol or ammonia based cleaning products. Abrasive chemicals, such as alcohol or ammonia, may damage the monitor. The company is not responsible for the damages to the monitor caused by the use of alcohol or ammonia based cleaning products. 2 Items User Manual LCD Monitor DC Adapter 15-pin D-Sub Signal Cable Notice RCA Cable Audio Cable S-Video Cable External TV Box Please make sure the following items are included with your monitor. If any items are missing, contact your dealer. 3 Setting up the LCD monitor Where is a good place to position the monitor? Place the LCD monitor on a solid and flat surface. If dropped, the screen can be damaged easily. 10 How to connect the power cord and the several cables to the LCD monitor. No. Name Cable connections No. Name Cable connections PC AUDION IN Speaker Cable VIDEO1 DVD/VCR Cable (Yellow) SPK OUT External Speaker Cable AUDIO(R) Audio output(R) (Red) DC12V DC Adaper AUDIO(L) Audio output(L) (White) PC 15-pin D-Sub Signal Cabie VIDEO2 S-Videl Cable 10 Ext External TV BOX 11 Connecting Your LCD Monitor ●Connecting your PC system 1. Connect the 15-pin D-Sub Signal Cable from PC to No.4. 2. If you use a speaker, connect the Audio Cable from PC to No.1. 3. If you use a headphone and earphone, connect the Headphone Cable from PC to No.2. ● Connecting your AV(DVD, VIDEO, CAMCODER) & TV 1. Connect the DVD/VCR Cable from PC to No.6, No.7 and No.8. 2. Connect the external TV box cable to NO.10. 3. Connect the S-Video cable to NO.9. FCC RF INTERFERENCE STATEMENT NOTE : This equipment tas been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment renerates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to redio commuications. Operation of this equipment in a residential area is likely to cause hamful interference in which case the will be required to correct the interference at his own expense. 12 Connecting for TV ● Connect the external TV Box to Monitors Ext. jack ● Connect the antenna cable to the external TV Box from wall antenna jack same as the below the picture Plug & Play The adoption of the new VESA Plug and Play solution eliminates complicated and time consuming setup. It allows you to install your monitor in a Plug and Play compatible system without the usual hassles and confusion. Your PC system can easily identify and configure itself for use with your display. This monitor automatically tells the PC system its Extended Display Identification Data (EDID) using Display Data Channel (DDC) protocols so the PC system can automatically configure itself to use the flat panel display. Warm-up Time All LCD monitors need time to become thermally stable whenever you turn on the monitor after letting the monitor be turned off for a couple of hours. Therefore, to achieve more accurate adjustments for parameters, allow the LCD monitor to be warmed up for at least 20 minutes before making any screen adjustments. 13 4 Adjusting The Monitor The Function Control Buttons How to use the function Key. You can change the display bnode (PC → Video → S-Video → TV) 1. First click : The OSD main menu appears. 2. Second click : The OSD menu disappears. 1. Select a command function. 2. When you push Auto button, this will optimize image quality automatically. Volume On/Off button. 14 Move the on-screen highlighted command item to the next one. 1. You can adjust the volume 2. Increase / Decrease the current option value. Power On/Off toggle button. 15 Main OSD Menu When you push the menu button, you can see below main OSD menu. PC Menu 1024 X 768 48.4KHz/ 60Hz Brightness : Adjusting Brightness Contrast : Adjusting Contrast H-Position : Adjusting Horizontal position V-Position : Adjusting Vertical position Clock : Adjusting Clock Phase : Adjusting Phase Color : Adjusting Color OSD function : H, V-Position, Language, off timer : Select input Exit Menu 16 COLOR ● ● ● ● The tone of color can be changed form bluish white to reddish white. Color1 - Blue type Color2 - Red type RED, GREEN, BLUE - You can adjust red, green and blue values that you want. Color COLOR 1 COLOR 2 USER COLOR 1024 X 768 48.4KHz/ 60Hz USER COLOR Red Gain / Green Gain / Blue Gain : You can adjust red, green and blue values that you want User Color RED GAIN GREEN GAIN BLUE GAIN EXIT 17 OSD FUNCTION Sets the OSD menu display position. H-Position : Moves the OSD menu to the horizontal direction. V-Position : Moves the OSD menu to the vertical direction. Language : Select OSD language. (English, Espanol, Francais, Deutsch, Italiano) Off timer : OSD display time. OSD function H POSITION V POSITION LANGUAGE OFF TIMER EXIT 18 VIDEO Apply Video function to Monitor. VIDEO Menu S-VIDEO Menu BRIGHTNESS : Adjusting Brightness CONTRAST : Adjusting Contrast COLOR : Adjusting Color OSD FUNCTION : H, V-Position, Language, off timer SELECT INPUT EXIT MENU 19 Color •COLOR : Adjust color intensity of the VIDEO. Color COLOR TINT SHARPNESS EXIT 20 •TINT : Adjust a color tone of the VIDEO. •SHARPNESS : Make image of the VIDEO looked sharper. TV TV Menu Channel: TV의 채널을 수신합니다. Channel Channel AIR/CATV AUTO. SEARCH MANUAL SETTING FINE ADJUSTM ▶ CATV ▶ STOP ▶ 15 ADD ▶0 •AIR/CATV : Select AIR or CATV. •AUTOSEARCH: Search the channel automatically. (SELECT button button : select channel SELECT button (ADD/DEL)) •MANUAL SETTING : Search the channel manually. •FINE ADJUSTM : Adjust image quality of the TV. The mode button can adjust lnput Source by hot key. 주의 In this case, the mode change time spend 2~3sec. 21 5 Appendix Appendix A. Display Modes Mode Resolution 720 X 400 Horizontal Vertical Pixel Clock Sync Frequency(KHz) Frequency(Hz) Frequency(MHz) Polarity(H/V) 31.468 70.087 28.322 -/+ 31.468 59.940 25.175 -/- 35.000 66.670 30.240 -/- 37.500 75.000 31.500 -/- 37.879 60.300 40.000 +/+ 48.077 72.188 50.000 +/+ 46.875 75.000 49.500 +/+ 48.363 60.004 65.000 -/- 56.476 70.000 75.000 -/- 60.023 75.029 78.750 +/+ VGA 640 X 480 SVGA XGA 800 X 600 1024 X 768 ※ The optimal resolution is 1024*768/60Hz. 22 Appendix B. 15-pan D-Sub Connector ● Input signal : Analog RGB ● 15-pin D-Sub connector Pin No. Signal Name Pin No. Signal Name Pin No. Signal Name Analog Red Input Analog Red Ground 11 Ground Analog Green Input Analog Green Ground 12 DDC Data Analog Blue Input Analog Blue Ground 13 Horizontal Sync Ground No Connect 14 Vertical Sync DDC Ground 10 Sync Ground 15 DDC Clock 15pin D-Sub Signal Cable 23 Appendix C. DPMS Power Saving Mode This monitor has a built-in power management system called DPMS Power Saving Mode. This system saves energy by switching your monitor into a low-power mode when it has not been used for a certain period of time. The available modes are “ON”, “Standby”, “Suspend”, and “OFF”. H-sync Signal V-sync RGB ON Active Active Active Stanby mode Inactive Active Blanked Suspend mode Active Inactive Blanked OFF Inactive Inactive Blanked State 24 Power Recovery Consumption Time Under 30Watt LED Color and Operting status Green Amber Less than 5Watt Within 2Sec Amber Amber 6 Troubleshooting What you see Suggested Actions Screen is blank and power indictor is off Ensure that the power cord is firmly connected and the LCD monitor is on. “out of range” message •Check the maximum resolution and the frequency of the video adaptor. •Compare these values with the data in the Display Modes Timing Chart. “No signal input” message •Ensure that the signal cable is firmly connected to the PC or video sources. •Ensure that the PC or video sources are turned on. Image is not stable and may appear to vibrate •Check that the display resolution and frequency from your PC or video board is an available mode for your monitor. On your computer check : Control Panel, Display, Settings •Note : Your monitor supports multiscan display functions within the following frequency domain: The image is too light or too dark •Adjust the Brightness and Contrast. •Refer to the Brightness/Contrast The image color is not good Image is not centered on the screen Screen is blank and power indicator light is steady amber or blinks every 0.5 or 1 seconds •Adjust the Color •Refer to the Color •Executes Auto Configuration. •The monitor is using its power management system. •Move the computer’s mouse or press a key on the keyboard. 25 26 Appendix A. Specifications Type Panel Size Pixel Pitch Display Color Basic Display Resolution Maximum Horizontal Frequency Vertical Sync Signal Connectors Tilting Degree (U/D) Plug&Play Input Output Power Consumption Standby mode Power Management Temperature Environmental Consideration Humidity Outside Dimensions Monitor Weight Carton TFT active matrix 15 inch 304.1mm×228.1mm 0.297mm×0.297mm 8-bit (16,777,216 colors) 1 0 2 4×7 6 8 @ 6 0 H z 1024×768@75Hz 31.5~60KHz 56~75Hz TTL, P. or N. D-Sub 15pin connector Speaker Input / Headphone Output (Audio Cable) Audio Cable RCA Cable S-Video Cable External TV Box Degree VESA DDC 1/2B 90~265VAC Adapter DC 12V, 3A Under 30W 5W less VESA DPMS 0~40°C (32°F~104°F) 90% less 435mm(W)×425mm(H)×241mm(D) 4.0kg 2.5kg ※ The specification of this monitor is subject to be changed without notice to improve performance. WOO YOUNG Telecom CO.,LTD. http://www.wyt.co.kr P/N : 97E9500023
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.2 Linearized : No Creator : .歯. QuarkXPress3.3K Create Date : 2003:03:21 17:19:19 Author : .歯.3 Producer : Acrobat PDFWriter 4.0 for Power Macintosh Modify Date : 2003:03:21 17:21:11-08:00 Page Count : 30EXIF Metadata provided by EXIF.tools