Wooyoung Telecom HLM151XAR 15" Color LCD Monitor User Manual HLM151XAR Users manual
Wooyoung Telecom Co., Ltd. 15" Color LCD Monitor HLM151XAR Users manual
User Manual
| Download: |  |
| Mirror Download [FCC.gov] | |
| Document ID | 274607 |
| Application ID | 7Sqof8bBacwnF4Oi4d3qDQ== |
| Document Description | User Manual |
| Short Term Confidential | No |
| Permanent Confidential | No |
| Supercede | No |
| Document Type | User Manual |
| Display Format | Adobe Acrobat PDF - pdf |
| Filesize | 21.38kB (267234 bits) |
| Date Submitted | 2002-10-03 00:00:00 |
| Date Available | 2002-10-03 00:00:00 |
| Creation Date | 2002-10-02 14:56:21 |
| Producing Software | Acrobat Distiller 5.0 (Windows) |
| Document Lastmod | 2002-10-02 14:56:21 |
| Document Title | HLM151XAR Users manual.pdf |
| Document Creator | PScript5.dll Version 5.2 |
| Document Author: | Administrator |
FCC RF INTERFERENCE STATEMENT NOTE : This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures. Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio, TV technical for help. Only shielded interface cable should be used. Finally, any changes or modifications to the equipment by the user not expressly approved by the grantee or manufacturer could void the users authority to operate such equipment, Contents Before Setting up -------------------------------------------------------------------------------------------------------------- Brief Specification of LCD Monitor ----------------------------------------------------------------------------------- ------------------------------------------------------------------------------------------------------------------------ -------------------------------------------------------------------------------------------------------------------------------------- Precautions Items Setting up the LCD monitor ------------------------------------------------------------------------------------------- 8 Where is a good place to position the monitor? -------------------------------------------------------------- Check before connecting the power cord and the signal cable !! ---------------------------------- How to connect the power cord and the signal cable to the LCD monitor. -------------------- ----------------------------------------------------------------------------------------- ------------------------------------------------------------------------------------------------------------------------ Connecting Your LCD Monitor Plug & Play Warm-up Time ------------------------------------------------------------------------------------------------------------------- Adjusting The Monitor --------------------------------------------------------------------------------------------------- 10 The Function Control Buttons ----------------------------------------------------------------------------------------- How to use function control button --------------------------------------------------------------------------------- 10 ------------------------------------------------------------------------------------------------- 11 -------------------------------------------------------------------------------------------------------------- 12 ---------------------------------------------------------------------------------------------------------------------------- 13 How to use the Hot Key. Main OSD Menu COLOR 10 USER COLOR ----------------------------------------------------------------------------------------------------------------- OSD POSITION -------------------------------------------------------------------------------------------------------------- 13 14 VIDEO Appendix ------------------------------------------------------------------------------------------------------------------------------ 15 ---------------------------------------------------------------------------------------------------------------------------- 17 Appendix A. Display Modes ------------------------------------------------------------------------------------------- Appendix B. 15-pin D-Sub Connector ---------------------------------------------------------------------------- Appendix C. DPMS Power Saving Mode Troubleshooting 17 17 ---------------------------------------------------------------------- 18 -------------------------------------------------------------------------------------------------------------- 19 1 Before Setting up This is 15 inch TFT-LCD monitor. Before Setting up the LCD Monitor, Please this manual read help your understanding ok. Brief Specification of LCD Monitor Resolution : 15 inch XGA (1024 X 768 @60Hz) Color display : 16,777,216 colors DPMS (Display Power Management Signaling) OSD (On Screen Display) Auto Configuration : Hot key DDC 1/2B : Plug & Play Speaker : Max 4W [2W X 2W] Notice According to PC system, DDC 1/2B may not be supported. If you meet Display Error message, check your video card which compatibility with DDC. If you want to know more information, please contact our service center. Precautions Check the voltage corresponds to the local electrical supply before connecting the AC power cord, Do not use Ketone type material (ex. Acetone), Ethyl Alcohol, Toluene, Ethyl Acid or Methyl chloride, to clear the panel. It might permanently damage the panel. Never use the damaged AC power cord. Keep it away from stoves, heaters, fireplaces and other sources of heat and magnets. Don’t put your LCD monitor in a location with high humidity and dust. Temperature : 0~40 ˚C Humidity : 90% less Place the LCD monitor on a solid surface. If dropped, the screen can be damaged easily. Don’t touch the screen with a acute nail and pin The LCD monitor consists of electrical devices. If the LCD monitor is damaged, contact immediately our service center. The LCD monitor can be damaged easily by shock. If you don’t use the LCD monitor for a long time, unplug the LCD monitor. Don’t use your LCD monitor in under direct sunlight. 2 Items User Manual LCD Monitor DC Adapter Notice 15-pin D-Sub Signal Cable Please make sure the following items are included with your monitor. If any items are missing, contact your dealer. RCA Cable Audio Cable 3 Setting up the LCD monitor Where is a good place to position the monitor? Place the LCD monitor on a solid and flat surface. If dropped, the screen can be damaged easily. Check before connecting the power cord and the signal cable !! Turn off the PC power before connecting power cord and signal cable to the LCD monitor. How to connect the power cord and the signal cable to the LCD monitor. Rear right side Connecting Your LCD Monitor 1. First, you can connect the power cord to the LCD monitor and AC outlet. 2. You can connect the signal cable to the LCD monitor and the PC system. 3. Connect with the audio cable from PC’S sound card to monitor’s SPK jack. 4. Connect DVD or VCR cable to Video Jack (Video). 5. Connect the Audio cable to Audio Jack (Audio(R), Audio(L)). Plug & Play The adoption of the new VESA( Plug and Play solution eliminates complicated and time consuming setup. It allows you to install your monitor in a Plug and Play compatible system without the usual hassles and confusion. Your PC system can easily identify and configure itself for use with your display. This monitor automatically tells the PC system its Extended Display Identification Data (EDID) using Display Data Channel (DDC) protocols so the PC system can automatically configure itself to use the flat panel display. Warm-up Time All LCD monitors need time to become thermally stable whenever you turn on the monitor. Therefore, to achieve more accurate adjustments for parameters, allow the LCD monitor to be warmed up for at least 20 minutes before making any screen adjustments. 4 Adjusting The Monitor The Function Control Buttons The function control buttons for monitor are located on the bottom side of the LCD monitor. How to use the function control button. Start the Main OSD Menu Adjust values 10 Move to the icon that you want Save Adjust values Select the icon Move the menu bar that you want Move to the EXIT Finish the menu bar Select the menu bar Finish the OSD menu How to use the Hot Key. AUTO : When you push Auto button, this will optimize image quality automatically. VOLUME : When you push the Left/Right button, you can adjust the volume. Notice While menu displays on the screen, don’t use hot key. If you want to use hot key, you must finish the menu status. 11 Main OSD Menu When you push the menu button, you can see below main OSD menu. PC Menu 1024 X 768 48.4KHz/ 60Hz Brightness : Adjusting Brightness Contrast : Adjusting Contrast H-Position : Adjusting Horizontal position V-Position : Adjusting Vertical position Clock : Adjusting Clock Phase : Adjusting Phase Color : Adjusting Color OSD function : H, V-Position, Language, off timer Select input : Select, Video1 Exit Menu 12 Video2 S-Video PC COLOR The tone of color can be changed from bluish white to reddish white. Color1 - Blue type Color2 - Red type User Color - You can select the color. Color Color 1 Color 2 User Color 1024 X 768 48.4KHz/ 60Hz USER COLOR Red Gain / Green Gain / Blue Gain : You can adjust red, green and blue values that you want User Color Red gain Green gain Blue gain Exit 13 OSD FUNCTION Sets the OSD menu display position. H-Position : Moves the OSD menu to the horizontal direction. V-Position : Moves the OSD menu to the vertical direction. Language : Select OSD language. (English, Espanol, Francais, Deutsch, Italiano) Off timer : OSD display time. OSD function H Position V Position Language Off Timer Exit 14 VIDEO Apply Video function to Monitor. VIDEO Menu Brightness : Adjusting Brightness Contrast : Adjusting Contrast Color : Adjusting Color OSD function : H, V-Position, Language, off timer Select input : Select, Video1 Video2 S-Video PC Exit Menu 15 COLOR COLOR : Adjust color intensity of the VIDEO. Color Color Tint Sharpness Exit 16 TINT : Adjust a color tone of the VIDEO. SHARPNESS : Make image of the VIDEO looked sharper. 5 Appendix Appendix A. Display Modes Mode Resolution Horizontal Frequency (KHz) 720 X 400 VGA 640 X 480 SVGA 800 X 600 XGA 1024 X 768 Vertical Pixel Clock Sync Polarity Frequency (Hz) Frequency (MHz) (H/V) 31.468 31.468 35.000 37.500 37.879 48.077 46.875 48.363 56.476 60.023 70.087 59.940 66.670 75.000 60.300 72.188 75.000 60.004 70.000 75.029 28.322 25.175 30.240 31.500 40.000 50.000 49.500 65.000 75.000 78.750 Pin No. Signal Name Pin No. -/+ -/-/-/+/+ +/+ +/+ -/-/+/+ Appendix B. 15-pin D-Sub Connector * Input signal : Analog RGB * 15-pin D-Sub connector Pin No. Signal Name Signal Name Analog Red Input Analog Red Ground 11 Ground Analog Green Input Analog Green Ground 12 DDC Data Analog Blue Input Analog Blue Ground 13 Horizontal Sync Ground No Connect 14 Vertical Sync DDC Ground 10 Sync Ground 15 DDC Clock 17 D-Sub Appendix C. DPMS Power Saving Mode This monitor has a built-in power management system called DPMS Power Saving Mode. This system saves energy by switching your monitor into a low-power mode when it has not been used for a certain period of time. The available modes are “ON”, “Standby”, “Suspend”, and “OFF”. State ON Standby Signal H-sync V-sync RGB Active Active Active Inactive Active Blanked Active Inactive Blanked Inactive Inactive Blanked Power Consumption Under 30Watt Recovery Time LED Color and Operating status Green Amber mode Suspend mode OFF 18 Less than Within 2 3Watt Sec Amber Amber 6 Troubleshooting What you see... Suggested Actions Screen is blank and power indicator is off Ensure that the power cord is firmly connected and the LCD monitor is on. “out of range” message Check the maximum resolution and the frequency of the video adaptor. Compare these values with the data in the Display Modes Timing Chart. “No signal input” message Ensure that the signal cable is firmly connected to the PC or video sources. Ensure that the PC or video sources are turned on. Image is not stable and may appear to vibrate Check that the display resolution and frequency from your PC or video board is an available mode for your monitor. On your computer check : Control Panel, Display, Settings Note : Your monitor supports multiscan display functions within the following frequency domain: Horizontal frequency : 31~60KHz Vertical frequency : 55~75Hz Maximum refresh rate : 1024 X 768 @75Hz The image is too light or too dark Adjust the Brightness and Contrast. Refer to the Brightness/Contrast The image color is not good Adjust the Color Refer to the Color Image is not centered on the screen Executes Auto Configuration. Screen is blank and power indicator light is steady amber or blinks every 0.5 or 1 seconds The monitor is using its power management system. Move the computer’s mouse or press a key on the keyboard. 19 MEMO 20
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.3 Linearized : No Create Date : 2002:10:02 14:56:21-07:00 Modify Date : 2002:10:02 14:56:21-07:00 Page Count : 22 Creation Date : 2002:10:02 21:56:21Z Mod Date : 2002:10:02 21:56:21Z Producer : Acrobat Distiller 5.0 (Windows) Author : Administrator Metadata Date : 2002:10:02 21:56:21Z Creator : Administrator Title : HLM151XAR Users manual.pdfEXIF Metadata provided by EXIF.tools