XAC Automation E25C PINPAD User Manual

XAC Automation Corporation PINPAD

User Manual.pdf

d CHIP AND PIN MOBILE PAYMENT DEVICE XCE-25-C INSTALLATION GUIDE
1. BEFORE STARTING There is a micro USB port (Figure 1) covered under the protection cover (Figure 2); this port is used for battery charging, debugging, firmware update and key injection. NOTE: The battery of xCE-25-C is built-in and rechargeable. Figure 1 Figure 2  Operating Temperature: 0oC to 40oC  Battery Pack: 3.7V, 1050mAh  Input: 5V, 500mA 2. POWER ON/OFF THE DEVICE To power on the device, press and hold the Power key for five seconds until the green LED light flashes and the screen shows words. Once it is powered on, the LED will blink every five seconds to indicate it is active. To power off the device, press and hold the Power key for five seconds until the screen become blank. Figure 3 NOTE: xCE-25-C will power off itself automatically if unused for 5 minutes.
3. CONNECTING TO SMART DEVICES Once xCE-25-C is powered on Bluetooth will be searchable. From the smart device’s Bluetooth settings, pair and connect to xCE-25-C. 4. USING THE MAGNETIC CARD READER Find the magnetic card reader slot on the right side of the device (Figure 4). Swipe the card through the slot with magnetic stripe side facing the same direction as the keypad (Figure 5). Figure 4 Figure 5 5. USING THE IC CARD READER Find the IC card reader slot on the bottom of the device (Figure 6). Insert an IC card into the slot with the chip side facing the same direction as the keypad (Figure 7). Figure 6 Figure 7 6. USING THE KEY PAD Press Cancel(X) key to terminate any current function and press the Enter(O) key to confirm a value or an option. Press the numeric key to enter the desirable numbers. Press the letter B should press 2 number key twice, then the screen displays “B” (Figure 8). Figure 8
7. USING THE CONTACTLESS CARD READER Contactless reader antenna is around the display and PIN pad. It will light up with LED signal when terminal is powered on and that means reader is working normally. Put contactless card to approach the antenna of card reader (Figure 9) for reading the card data during transaction. Figure 9
Federal Communication Commission Interference Statement This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures: - Reorient or relocate the receiving antenna. - Increase the separation between the equipment and receiver. - Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. - Consult the dealer or an experienced radio/TV technician for help. FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment.
This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. Radiation Exposure Statement: The product comply with the FCC portable RF exposure limit set forth for an uncontrolled environment and are safe for intended operation as described in this manual. The further RF exposure reduction can be achieved if the product can be kept as far as possible from the user body or set the device to lower output power if such function is available. The above information is the exclusive intellectual property of XAC Automation Corporation and shall not be disclosed, distributed or reproduced without permission of XAC Automation Corporation. XAC AUTOMATION CORP. shall not be held liable for technical and editorial omissions or errors made herein; nor for incidental or consequential damages resulting from the furnishing, performance or use of his material. XAC Automation Corporation 886-3-577-2738 www.xac.com.tw

Navigation menu