XAC Automation E25CMFI PINPAD User Manual VU1 228 160309 Installation Guide xCE E25C
XAC Automation Corporation PINPAD VU1 228 160309 Installation Guide xCE E25C
User Manual rev.pdf
d
CHIP AND PIN MOBILE PAYMENT DEVICE
XCE_E25C / XCE-25-C
INSTALLATION GUIDE
1.
B
EFORE
S
TARTING
On the top of xCE_E25C (also called xCE-25-C), there is a micro USB port and reset pin hole
(Figure 1) covered under the protection cover (Figure 2); this port is used for battery charging,
debugging, firmware update and key injection.
NOTE: The battery of xCE_E25C is built-in and rechargeable.
Figure 1 Figure 2
Operating Temperature: 0
o
C to 40
o
C
Battery Pack: 3.7V, 1050mAh
Input: 5V, 500mA
2.
P
OWER
O
N
/O
FF THE
D
EVICE
Pressing the power button once, battery capacity will be displayed.
To power on the device, press and hold the Power key for five seconds until the buzzer sound
is heard, and screen is activated.
To power off the device, press and hold the Power key for five seconds until the buzzer sound
is heard, and screen becomes blank.
Figure 3
NOTE: xCE_E25C will power off itself automatically if unused for 5 minutes.
3.
C
ONNECTING TO
S
MART
D
EVICES
Once xCE_E25C is powered on, Bluetooth will be searchable. From the connecting device’s
Bluetooth settings, pair and connect to xCE_E25C.
4.
U
SING THE
M
AGNETIC
C
ARD
R
EADER
Find the magnetic card reader slot on the right side of the device (Figure 4). Swipe the card
through the slot with magnetic stripe side facing the same direction as the keypad (Figure 5).
Figure 4 Figure 5
5.
U
SING THE
IC
C
ARD
R
EADER
Find the IC card reader slot on the bottom of the device (Figure 6). Insert an IC card into the
slot with the chip side facing the same direction as the keypad (Figure 7).
Figure 6 Figure 7
6.
U
SING THE
C
ONTACTLESS
C
ARD
R
EADER
Place the contactless card on top of the contactless logo (Figure 8).
Figure 8
7.
U
SING THE
K
EY
P
AD
Press Cancel(X) key to terminate any current function and press the Enter(O) key to confirm a
value or an option. Press the numeric key to enter the desirable numbers.
F
EDERAL
C
OMMUNICATION
C
OMMISSION
I
NTERFERENCE
S
TATEMENT
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two
conditions: (1) This device may not cause harmful interference, and (2) this device must accept
any interference received, including interference that may cause undesired operation.
Note:This equipment has been tested and found to comply with the limits for a Class A digital
device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference when the equipment is operated in a commercial
environment. This equipment generates, uses, and can radiate radio frequency energy and, if
not installed and used in accordance with the instruction manual, may cause harmful
interference to radio communications. Operation of this equipment in a residential area is likely
to cause harmful interference in which case the user will be required to correct the interference
at his own expense.
FCC Caution: Any changes or modifications not expressly approved by the party responsible for
compliance could void the user's authority to operate this equipment.
This transmitter must not be co-located or operating in conjunction with any other antenna or
transmitter.
Radiation Exposure Statement:
The product comply with the FCC portable RF exposure limit set forth for an uncontrolled
environment and are safe for intended operation as described in this manual. The further RF
exposure reduction can be achieved if the product can be kept as far as possible from the user
body or set the device to lower output power if such function is available.
CAUTION
RISK OF EXPLOSION IF BATTERY IS REPLACED BY AN INCORRECT TYPE. DISPOSE OF
USED BATTERIES ACCORDING TO THE INSTRUCTIONS.
The above information is the exclusive intellectual property of XAC Automation Corporation and shall not be disclosed,
distributed or reproduced without permission of XAC Automation Corporation.
XAC AUTOMATION CORP. shall not be held liable for technical and editorial omissions or errors made herein; nor for
incidental or consequential damages resulting from the furnishing, performance or use of his material.
XAC Automation Corporation
886-3-577-2738
www.xac.com.tw