XAC Automation XC50 Cradle User Manual rev 3

Download:
Mirror Download [FCC.gov]
Document ID	3622271
Application ID	zSUZZ5ODxpsfiCrMyyJfvw==
Document Description	Users Manual rev 3.pdf
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	68.07kB (850931 bits)
Date Submitted	2017-10-30 00:00:00
Date Available	2018-04-28 00:00:00
Creation Date	2017-10-26 21:49:46
Producing Software	Acrobat Distiller 7.0 (Windows)
Document Lastmod	2017-10-27 16:24:30
Document Title	Microsoft Word - Installation Guide_XC50_certification_Modify modem to RJ45 del Figure 4 Type C connector_20171026-1
Document Creator	PScript5.dll Version 5.2.2
Document Author:	ninlin

TERMIINAL PAYM
MENT CRAD
DLE
XC50
INSTTALLATIO
ON GUIDE
1. PACKAGE CONTENT
„
XC50
„
Power adaptor
2. DEVICE OVERVIEW
XC50 Key Buttons & Interface Ports (Figure 1):
REAR
Figure 1
BACK AREA
COM1
COM2
USB
RJ45
Reset Button
„
Paper Roll
FRONT
Figure 2
Figure 3
FRONT AREA
Charging Contact
LED
Paper Roll
BOTTOM
Figure 4
BOTTOM AREA
DC JACK
■ XC50 Power spec:
Input: 12V DC, 3A
■ Power Adapter spec:
Input: 100 ~240 ac
Output: 12V DC, 3A
This symbol is intended to alert the user before starting using the POS.
Caution: This product shall be only used with a certified power supply unit which was
investigated according to the standard ofIEC 60950‐1, UL 60950‐1 and CAN/CSA C22.2 No.
60950‐1‐07, CSA C22.2 No. 60950‐1, and marked “I.T.E. LPS”, and with operating temperature:
minimum 40°C, output rated: 12V DC, minimum 3 A.
„
Operating Temperature: 0oC to 40oC
3. POWER ON/OFF THE DEVICE
To power on the device: Plug in the DC JACK
To power off the device: Plug off the DC JACK
Figure 5
4. LED BEHAVIORS
Insert Power adapter and device will power up, there is a LED status:
„
Location:
Top right corner (Figure 6)
Figure 6
„
Solid Red – XC50 is powered up and under booting process
„
Solid Green – XC50 booting process is successfully completed
„
Blinking Red –Firmware update process
„
Red Light On –Error status (system errors and firmware upgrade failed)
„
Solid Orange – For printer status
5. LOADING THE PAPER
Gently pop the printer cover’s latch; then pull the cover (Figure 7). Load a roll of thermal paper
into the printer. Load it so that the print‐side of the paper will feed out facing the operator.
Close the cover by pressing on the center of the printer cover. Use the serrated bar to tear off
any excess paper.
Figure 7
Federal Communication Commission Interference Statement
This device complies with Part 15 of the FCC Rules. Operation is subject to the following
two conditions: (1) This device may not cause harmful interference, and (2) this device
must accept any interference received, including interference that may cause undesired
operation.
This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This
equipment generates, uses and can radiate radio frequency energy and, if not installed and
used in accordance with the instructions, may cause harmful interference to radio
communications.
However, there is no guarantee that interference will not occur in a
particular installation.
If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by one of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that
to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
FCC Caution: Any changes or modifications not expressly approved by the party
responsible for compliance could void the user's authority to operate this equipment.
This transmitter must not be co-located or operating in conjunction with any other antenna
or transmitter.
Radiation Exposure Statement:
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled
environment. This equipment should be installed and operated with minimum distance
20cm between the radiator & your body.
Note: The country code selection is for non-US model only and is not available to all US
model. Per FCC regulation, all WiFi product marketed in US must fixed to US operation
channels only.
XAC Automation Corporation
886-3-577-2738
The above information is the exclusive intellectual property of XAC Automation Corporation and shall not be
disclosed, distributed or reproduced without permission of XAC Automation Corporation.

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.6
Linearized                      : Yes
Encryption                      : Standard V2.3 (128-bit)
User Access                     : Print, Extract
XMP Toolkit                     : Adobe XMP Core 4.0-c316 44.253921, Sun Oct 01 2006 17:14:39
Producer                        : Acrobat Distiller 7.0 (Windows)
Creator Tool                    : PScript5.dll Version 5.2.2
Modify Date                     : 2017:10:27 16:24:30+08:00
Create Date                     : 2017:10:26 21:49:46+08:00
Metadata Date                   : 2017:10:27 16:24:30+08:00
Format                          : application/pdf
Title                           : Microsoft Word - Installation Guide_XC50_certification_Modify modem to RJ45 del Figure 4 Type C connector_20171026-1
Creator                         : ninlin
Document ID                     : uuid:09ceac14-6535-46ba-af84-a58a57047874
Instance ID                     : uuid:6e065751-ec4d-4880-a19c-b92846656f57
Page Count                      : 8
Author                          : ninlin

EXIF Metadata provided by EXIF.tools