XAVi Technologies XW201M Wireless Mini PCI User Manual

XAVi Technologies Corp. Wireless Mini PCI Users Manual

Users Manual

Hardware Specification for XW201M RF ModuleBlock Diagram: Processor : Atheros AR2414 single chip integrated with the MAC/baseband/radio Memory :I/O Interface : Feature :  Wi-fi Wireless Access Point  IEEE802.11b/g  2.4G Dipole Antenna  Rx Sensitivity Antenna Interface :1x2.4G Dipole Antenna. minpciSerial EEPROM:32K
 Transmit PowerTest Name Data Rate DUT Measured11g RX Sensitivity 6Mbps -88RX Sensitivity 36Mbps -73RX Sensitivity 48Mbps -70RX Sensitivity 54Mbps -6811b RX Sensitivity 1Mbps -90RX Sensitivity 2Mbps -87RX Sensitivity 5.5Mbps -86RX Sensitivity 11Mbps -85Test Name Data Rate DUT Measured11g Transmit power 6Mbps 17 (+1.5/-1.5) dBm Transmit power 36Mbps 16 (+1.5/-1.5) dBm Transmit power 48Mbps 15 (+1.5/-1.5) dBm Transmit power 54Mbps 14 (+1.5/-1.5) dBm 11b Transmit power 1Mbps 17 (+1.5/-1.5) dBm Transmit power 2Mbps 17 (+1.5/-1.5) dBm Transmit power 5.5Mbps 17 (+1.5/-1.5) dBm Transmit power 11Mbps 17 (+1.5/-1.5) dBm Antenna solder here
Federal Communication Commission Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures: - Reorient or relocate the receiving antenna. - Increase the separation between the equipment and receiver. - Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. -Consult the dealer or an experienced radio/TV technician for help. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. IMPORTANT NOTE: This module is intended for OEM integrator. The OEM integrator is still responsible for the FCC compliance requirement of the end product, which integrates this module. 20cm minimum distance has to be able to be maintained between the antenna and the users for the host this module is integrated into. Under such configuration, the FCC radiation exposure limits set forth for an population/uncontrolled environment can be satisfied. Any changes or modifications not expressly approved by the manufacturer could void the user's authority to operate this equipment. USERS MANUAL OF THE END PRODUCT: In the users manual of the end product, the end user has to be informed to keep at least 20cm separation with the antenna while this end product is installed and operated. The end user has to be informed that the FCC radio-frequency exposure guidelines for an uncontrolled environment can be satisfied. The end user has to also be informed that any changes or modifications not expressly approved by the manufacturer could void the user's authority to operate this equipment.ʳIf the size of the end product is smaller than 8x10cm, then additional FCC part 15.19 statement is required to be available in the users manual: This device complies with Part 15 of FCC rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference and (2) this device must accept any interference received, including interference that may cause undesired operation.
LABEL OF THE END PRODUCT: The final end product must be labeled in a visible area with the following " Contains TX FCC ID: RYUXW201M ". If the size of the end product is larger than 8x10cm, then the following FCC part 15.19 statement has to also be available on the label: This device complies with Part 15 of FCC rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference and (2) this device must accept any interference received, including interference that may cause undesired operation.

Navigation menu