Users Manual
| Download: |  |
| Mirror Download [FCC.gov] | |
| Document ID | 3005645 |
| Application ID | zwsNKW86WxczIb2HUNU0xA== |
| Document Description | Users Manual |
| Short Term Confidential | No |
| Permanent Confidential | No |
| Supercede | No |
| Document Type | User Manual |
| Display Format | Adobe Acrobat PDF - pdf |
| Filesize | 159.43kB (1992873 bits) |
| Date Submitted | 2016-05-26 00:00:00 |
| Date Available | 2016-05-26 00:00:00 |
| Creation Date | 2016-05-23 17:38:29 |
| Producing Software | Microsoft® Word 2013 |
| Document Lastmod | 2016-05-24 13:40:23 |
| Document Title | Users Manual |
| Document Creator | Microsoft® Word 2013 |
| Document Author: | Administrator |
Gecko Switch Quick Start Guide Using Your Switch Dimmer Button on/off with night light Dip For Finger To Open Button Download our APP for FREE Use your smartphone to turn on/off or adjust brightness using the dimmer, if applicable, of your light.” Gecko Switch Installation Gecko switch & AAA alkaline battery x 2 (come with the box) AAA AAA 3 Steps. 1 Inserting AAA batteries. Move your finger to the semi-circle shaped dip at the bottom of the press button. Use your nail to force open the press button by pulling upwards and out. Inserting two new Alkaline AAA batteries into the recess behind the main switch button of the Gecko Switch. The LED indicator at bottom of Gecko Switch will light up with power. Reattach the main switch button. AAA AAA AAA batteries 2 Linking to the Base Switch (optional) If you buy the Gecko switch with a Base Switch in the same package, they are already linked by default at the factory, so there is no need to manually link these switches. If you bought the Base Switch and Gecko Switch separately or somehow the link was broken, they can be linked manually by holding BOTH the main switch button and the “+” button for 3 seconds to enter pairing mode for both switches. A long beep will sound when successfully linked. 3 seconds Simultaneously Base Gecko 3 Stick the Gecko Switch anywhere you want Remove peel of the Gecko Glue at the back of the Gecko Switch. Then put it anywhere you like. To change location of the Gecko Switch, remove it very, very slowly. Then put it somewhere else. The glue pad can be removed and reused over and over again. Try it! HINT The Gecko Glue can be washed with water to regain its stickiness. Gecko Glue Gecko Glue Troubleshooting Symptom Cannot turn on/off the light LED flashes red Possible Cause Battery dead Link to Base Switch broken. Manually relink. Battery low Specifications Battery: Two Alkaline AAA batteries Bluetooth: Bluetooth 4.0 Operating ambient temperature: 32° to 95° F (0° to 35° C) Relative humidity: 5% to 95% noncondensing Warranty If, within one year from date of purchase, this product should become defective (except battery and glue), due to faulty workmanship or materials, it will be repaired or replaced, without charge. Proof of purchase and a Return Authorization are required. FCC The device is approved by the FCC and it complies with Part 15 of the FCC rules. Its operation is subject to the following two conditions: 1. This device may not cause harmful interference. 2. This device must accept any interference that may cause undesired operation. WARNING Changes or modifications to this unit not expressly approved by the party responsible of compliance could void the user’s authority to operate the equipment. Technical Assistance If you have any questions about the installation or operation of this product, please contact us at: help@ xmtl ab. co m w w w. geckosw i tc h . com Base Switch Quick Start Guide Using Your Switch Dimmer Button on/off with night light Dip For Finger To Open Button Download our APP for FREE Use your smartphone to turn on/off or adjust brightness using the dimmer, if applicable, of your light.” Warranty If, within one year from date of purchase, this product should become defective (except battery and glue), due to faulty workmanship or materials, it will be repaired or replaced, without charge. Proof of purchase and a Return Authorization are required. Specifications Rated: 100-240 VAC, 50/60Hz Max Load: 300 watts Operating ambient temperature: 32° to 95° F (0° to 35° C) Relative humidity: 5% to 95% noncondensing Base Switch Installation Warning Installing the Base Switch is an electrical shock hazard and may result in serious injury or death. If you are unfamiliar or uncomfortable with electrical work, please call a qualified electrician for installation. The Base Switch is designed to function as a standard light switch. It is also compatible with dimmable lights and can act as a dimmer. It is not compatible with 3 way switches. Base switch, wire nuts & screws Voltage detector (come with the box) Screwdriver Smartphone (optional for taking photos) 5 Steps. ON OFF ON ON Turn off power at circuit breaker for the switch you are replacing with the Base Switch. OFF Turning OFF power OFF Removing existing switch Remove the wall plate; use a voltage detector to make sure that the circuit is dead. Unscrew the old switch from the electrical box and pull it out with the wires still attached. Take some pictures of the wires for later reference then remove the wires from the old switch. •Turn Screws To Loosen. OFF •Take photos of the wires •Unscrew terminals OFF OFF 3 Wiring the Base Switch Load Hot(live) Ground Mounting the Base Switch to wallbox Move your finger to the semi-circle shaped dip at the bottom of the press button. Use your nail to force open the press button by pulling upwards and out. Insert the Base Switch into the wallbox. Then screw it in place. Push the main button back into the Base Switch OFF OFF HINT Remember the Base Switch and Gecko Switch is compatible with dimmable light bulbs. ON ON Turn on power at circuit breaker. Click the Base Switch to see if it works! Now you can link it to the Gecko Switch! OFF Turning ON power ON Troubleshooting Symptom Possible Cause Cannot turn on/off the light Wiring error. Burnt out light bulb. Check circuit breaker is turned back on. Light flicks or on/off automatically Using the dimmer function on a light bulb that is not dimmable. Light bulb is less than minimal load required by the base switch. Note that light bulb must be greater than 5 watts. FCC The device is approved by the FCC and it complies with Part 15 of the FCC rules. Its operation is subject to the following two conditions: 1. This device may not cause harmful interference. 2. This device must accept any interference that may cause undesired operation. WARNING Changes or modifications to this unit not expressly approved by the party responsible of compliance could void the user’s authority to operate the equipment. Technical Assistance If you have any questions about the installation or operation of this product, please contact us at: help@xmtl ab. co m w w w. gec kosw i tch . com RF Radiation Exposure Statement This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled environment.
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.6 Linearized : No Tagged PDF : No XMP Toolkit : 3.1-701 Format : application/pdf Creator : Administrator Create Date : 2016:05:23 17:38:29+08:00 Creator Tool : Microsoft® Word 2013 Modify Date : 2016:05:24 13:40:23+08:00 Metadata Date : 2016:05:24 13:40:23+08:00 Producer : Microsoft® Word 2013 Document ID : uuid:111b76a3-8970-49a3-a8e2-89c7f883ad01 Instance ID : uuid:2e5c69f0-6a36-4685-b862-763240485103 Page Count : 14 Language : zh-TW Author : AdministratorEXIF Metadata provided by EXIF.tools