Xilinx Ml605 Users Manual UG534 Hardware, User Guide
ML605 to the manual 1170a4f4-6444-4052-a950-f66e3c686daf
2015-02-03
: Xilinx Xilinx-Ml605-Users-Manual-473575 xilinx-ml605-users-manual-473575 xilinx pdf
Open the PDF directly: View PDF 
.
Page Count: 92
| Download | |
| Open PDF In Browser | View PDF |
ML605 Hardware
User Guide
User Guide [optional]
UG534 (v1.2.1) January 21, 2010 [optional]
Xilinx is disclosing this user guide, manual, release note, and/or specification (the "Documentation") to you solely for use in the development
of designs to operate with Xilinx hardware devices. You may not reproduce, distribute, republish, download, display, post, or transmit the
Documentation in any form or by any means including, but not limited to, electronic, mechanical, photocopying, recording, or otherwise,
without the prior written consent of Xilinx. Xilinx expressly disclaims any liability arising out of your use of the Documentation. Xilinx reserves
the right, at its sole discretion, to change the Documentation without notice at any time. Xilinx assumes no obligation to correct any errors
contained in the Documentation, or to advise you of any corrections or updates. Xilinx expressly disclaims any liability in connection with
technical support or assistance that may be provided to you in connection with the Information.
THE DOCUMENTATION IS DISCLOSED TO YOU “AS-IS” WITH NO WARRANTY OF ANY KIND. XILINX MAKES NO OTHER
WARRANTIES, WHETHER EXPRESS, IMPLIED, OR STATUTORY, REGARDING THE DOCUMENTATION, INCLUDING ANY
WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE, OR NONINFRINGEMENT OF THIRD-PARTY
RIGHTS. IN NO EVENT WILL XILINX BE LIABLE FOR ANY CONSEQUENTIAL, INDIRECT, EXEMPLARY, SPECIAL, OR INCIDENTAL
DAMAGES, INCLUDING ANY LOSS OF DATA OR LOST PROFITS, ARISING FROM YOUR USE OF THE DOCUMENTATION.
© 2009–2010 Xilinx, Inc. XILINX, the Xilinx logo, Virtex, Spartan, ISE, and other designated brands included herein are trademarks of Xilinx
in the United States and other countries. All other trademarks are the property of their respective owners. PCI, PCI Express, PCIe, and
PCI-X are trademarks of PCI-SIG.
Revision History
The following table shows the revision history for this document.
Date
Version
8/17/09
1.0
Initial Xilinx release.
11/17/09
1.1
•
•
•
•
Updated Figure 1-1, Figure 1-2, Figure 1-3, Figure 1-11, and Figure 1-14.
Added Figure 1-7, Figure 1-8, Figure 1-10, and Figure 1-13.
Updated Table 1-15 and Table 1-18.
Updated Appendix B, “VITA 57.1 FMC LPC (J63) and HPC (J64) Connector Pinout”
and Appendix C, “ML605 Master UCF.”
• Minor typographical edits.
01/15/10
1.2
• Updated Figure 1-2, Figure 1-3, Figure 1-17, Table 1-3, Table 1-8, Table 1-9, Table A-1,
and Table A-2. Miscellaneous typographical edits.
1/21/10
1.2.1
ML605 Hardware User Guide
Revision
• Corrected typos in Table 1-31 and Figure 1-28.
www.xilinx.com
UG534 (v1.2.1) January 21, 2010
Table of Contents
Preface: About This Guide
Guide Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Additional Documentation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Additional Support Resources . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Chapter 1: ML605 Evaluation Board
Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Additional Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Block Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Related Xilinx Documents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Detailed Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
1. Virtex-6 XC6VLX240T-1FFG1156 FPGA . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
I/O Voltage Rails . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2. 512 MB DDR3 Memory SODIMM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3. 128 Mb Platform Flash XL. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4. 32 MB Linear BPI Flash . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
ML605 Flash Boot Options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
5. System ACE CF and CompactFlash Connector . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
6. USB JTAG . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
7. Clock Generation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Oscillator (Differential) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Oscillator Socket (Single-Ended, 2.5V) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
SMA Connectors (Differential) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
8. Multi-Gigabit Transceivers (GTX MGTs) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
9. PCI Express Endpoint Connectivity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
10. SFP Module Connector . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
11. 10/100/1000 Tri-Speed Ethernet PHY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
SGMII GTX Transceiver Clock Generation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
12. USB-to-UART Bridge . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
13. USB Controller . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
14. DVI Codec . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
15. IIC Bus . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
8 Kb NV Memory . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
16. Status LEDs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Ethernet PHY Status LEDs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
FPGA INIT and DONE LEDs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
17. User I/O . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
User LEDs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
User Pushbutton Switches . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
User DIP Switch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
User SMA GPIO . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
LCD Display (16 Character x 2 Lines) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
18. Switches . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Power On/Off Slide Switch SW2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
ML605 Hardware User Guide
UG534 (v1.2.1) January 21, 2010
www.xilinx.com
13
13
14
15
20
20
21
24
26
27
27
27
29
31
32
35
36
37
39
40
41
42
44
45
46
47
47
48
49
50
51
52
53
53
3
FPGA_PROG_B Pushbutton SW4 (Active-Low) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
SYSACE_RESET_B Pushbutton SW3 (Active-Low) . . . . . . . . . . . . . . . . . . . . . . . . . . . .
System ACE CF CompactFlash Image Select DIP Switch S1 . . . . . . . . . . . . . . . . . . . . . .
Mode, Osc Enable, Boot EEPROM Select, and Addr Select DIP Switch S2 . . . . . . . . . . .
19. VITA 57.1 FMC HPC Connector . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
20. VITA 57.1 FMC LPC Connector . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
21. Power Management . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
AC Adapter and Input Power Jack/Switch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Onboard Power Regulation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
22. System Monitor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
54
54
55
56
57
63
65
65
66
68
Configuration Options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 73
Appendix A: Default Switch and Jumper Settings
Appendix B: VITA 57.1 FMC LPC (J63) and HPC (J64) Connector Pinout
Appendix C: ML605 Master UCF
Appendix D: References
4
www.xilinx.com
ML605 Hardware User Guide
UG534 (v1.2.1) January 21, 2010
Preface
About This Guide
This manual accompanies the Virtex®-6 FPGA ML605 Evaluation Board and contains
information about the ML605 hardware and software tools.
Guide Contents
This manual contains the following chapters:
•
Chapter 1, “ML605 Evaluation Board,” provides an overview of the embedded
development board and details the components and features of the ML605 board.
•
Appendix A, “Default Switch and Jumper Settings.”
•
Appendix B, “VITA 57.1 FMC LPC (J63) and HPC (J64) Connector Pinout.”
•
Appendix C, “ML605 Master UCF.”
•
Appendix D, “References.”
Additional Documentation
The following documents are also available for download at
http://www.xilinx.com/support/documentation/virtex-6.htm.
•
Virtex-6 Family Overview
The features and product selection of the Virtex-6 family are outlined in this overview.
•
Virtex-6 FPGA Data Sheet: DC and Switching Characteristics
This data sheet contains the DC and Switching Characteristic specifications for the
Virtex-6 family.
•
Virtex-6 FPGA Packaging and Pinout Specifications
This specification includes the tables for device/package combinations and maximum
I/Os, pin definitions, pinout tables, pinout diagrams, mechanical drawings, and
thermal specifications.
•
Virtex-6 FPGA Configuration Guide
This all-encompassing configuration guide includes chapters on configuration
interfaces (serial and SelectMAP), bitstream encryption, boundary-scan and JTAG
configuration, reconfiguration techniques, and readback through the SelectMAP and
JTAG interfaces.
•
Virtex-6 FPGA Clocking Resources User Guide
This guide describes the clocking resources available in all Virtex-6 devices, including
the MMCM and PLLs.
ML605 Hardware User Guide
UG534 (v1.2.1) January 21, 2010
www.xilinx.com
5
Preface: About This Guide
•
Virtex-6 FPGA Memory Resources User Guide
The functionality of the block RAM and FIFO are described in this user guide.
•
Virtex-6 FPGA SelectIO Resources User Guide
This guide describes the SelectIO™ resources available in all Virtex-6 devices.
•
Virtex-6 FPGA GTX Transceivers User Guide
This guide describes the GTX transceivers available in all Virtex-6 FPGAs except the
XC6VLX760.
•
Virtex-6 FPGA Embedded Tri-Mode Ethernet MAC User Guide
This guide describes the dedicated Tri-Mode Ethernet Media Access Controller
available in all Virtex-6 FPGAs except the XC6VLX760.
•
Virtex-6 FPGA DSP48E1 Slice User Guide
This guide describes the architecture of the DSP48E1 slice in Virtex-6 FPGAs and
provides configuration examples.
•
Virtex-6 FPGA System Monitor User Guide
The System Monitor functionality available in all Virtex-6 devices is outlined in this
guide.
•
Virtex-6 FPGA PCB Design Guide
This guide provides information on PCB design for Virtex-6 devices, with a focus on
strategies for making design decisions at the PCB and interface level.
Additional Support Resources
To search the database of silicon and software questions and answers or to create a
technical support case in WebCase, see the Xilinx website at:
http://www.xilinx.com/support.
6
www.xilinx.com
ML605 Hardware User Guide
UG534 (v1.2.1) January 21, 2010
Chapter 1
ML605 Evaluation Board
Overview
The ML605 board enables hardware and software developers to create or evaluate designs
targeting the Virtex®-6 XC6VLX240T-1FFG1156 FPGA.
The ML605 provides board features common to many embedded processing systems.
Some commonly used features include: a DDR3 SODIMM memory, an 8-lane PCI
Express® interface, a tri-mode Ethernet PHY, general purpose I/O, and a UART.
Additional user desired features can be added through mezzanine cards attached to the
onboard high-speed VITA-57 FPGA Mezzanine Connector (FMC) high pin count (HPC)
expansion connector, or the onboard VITA-57 FMC low pin count (LPC) connector.
“Features,” page 8 provides a general listing of the board features with details provided in
“Detailed Description,” page 11.
Additional Information
Additional information and support material is located at:
•
http://www.xilinx.com/ml605
This information includes:
•
Current version of this user guide in PDF format
•
Example design files for demonstration of Virtex-6 FPGA features and technology
•
Demonstration hardware and software configuration files for the System ACE™ CF
controller, Platform Flash configuration storage device, and linear flash chip
•
Reference design files
•
Schematics in PDF and DxDesigner formats
•
Bill of materials (BOM)
•
Printed-circuit board (PCB) layout in Allegro PCB format
•
Gerber files for the PCB (Many free or shareware Gerber file viewers are available on
the internet for viewing and printing these files.)
•
Additional documentation, errata, frequently asked questions, and the latest news
For information about the Virtex-6 family of FPGA devices, including product highlights,
data sheets, user guides, and application notes, see the Virtex-6 FPGA documentation page
at http://www.xilinx.com/support/documentation/virtex-6.htm.
ML605 Hardware User Guide
UG534 (v1.2.1) January 21, 2010
www.xilinx.com
7
Chapter 1: ML605 Evaluation Board
Features
The ML605 provides the following features:
•
1. Virtex-6 XC6VLX240T-1FFG1156 FPGA
•
2. 512 MB DDR3 Memory SODIMM
•
3. 128 Mb Platform Flash XL
•
4. 32 MB Linear BPI Flash
•
5. System ACE CF and CompactFlash Connector
•
6. USB JTAG
•
7. Clock Generation
•
•
8
♦
Fixed 200 MHz oscillator (differential)
♦
Socketed 2.5V oscillator (single-ended)
♦
SMA connectors (differential)
♦
SMA connectors for MGT clocking
8. Multi-Gigabit Transceivers (GTX MGTs)
♦
FMC - HPC connector
♦
FMC - LPC connector
♦
SMA
♦
PCIe
♦
SFP Module connector
♦
Ethernet PHY SGMII interface
9. PCI Express Endpoint Connectivity
♦
Gen1 8-lane (x8)
♦
Gen2 4-lane (x4)
•
10. SFP Module Connector
•
11. 10/100/1000 Tri-Speed Ethernet PHY
•
12. USB-to-UART Bridge
•
13. USB Controller
•
14. DVI Codec
•
15. IIC Bus
♦
IIC EEPROM - 1 KB
♦
DDR3 SODIMM socket
♦
DVI CODEC
♦
DVI connector
♦
FMC HPC connector
♦
FMC LPC connector
♦
SFP module connector
www.xilinx.com
ML605 Hardware User Guide
UG534 (v1.2.1) January 21, 2010
Overview
•
•
•
16. Status LEDs
♦
Ethernet status
♦
FPGA INIT
♦
FPGA DONE
♦
System ACE CF Status
17. User I/O
♦
USER LED Group 1 - GPIO (8)
♦
USER LED Group 2 - directional (5)
♦
User pushbuttons - directional (5)
♦
CPU reset pushbutton
♦
User DIP switch - GPIO (8-pole)
♦
User SMA GPIO connectors (2)
♦
LCD character display (16 characters x 2 lines)
18. Switches
♦
Power on/off slide switch
♦
System ACE CF reset pushbutton
♦
System ACE CF bitstream image select DIP switch
♦
Configuration MODE DIP switch
•
19. VITA 57.1 FMC HPC Connector
•
20. VITA 57.1 FMC LPC Connector
•
21. Power Management
•
♦
PMBus voltage and current monitoring via TI power controller
♦
22. System Monitor
Configuration Options
♦
3. 128 Mb Platform Flash XL
♦
4. 32 MB Linear BPI Flash
♦
5. System ACE CF and CompactFlash Connector
♦
6. USB JTAG
ML605 Hardware User Guide
UG534 (v1.2.1) January 21, 2010
www.xilinx.com
9
Chapter 1: ML605 Evaluation Board
Block Diagram
Figure 1-1 shows a high-level block diagram of the ML605 and its peripherals.
X-Ref Target - Figure 1-1
JTAG USB Mini-B
USB JTAG Circuit
System ACE CF
S.A. CompactFlash
S.A. 8-bit MPU I/F
VITA 57.1 FMC
HPC Connector
BANK32
Platform Flash
Linear BPI Flash
BANK12, 13 BANK15,16
BANK14,22 BANK34,116
BANK23,24
BANK112,113
BANK0
BANK24
BANK34
SYSMON I/F
INIT, DONE LEDs
PROG PB, MODE SW
IIC Bus
IIC EEPROM
FMC HPC
DDR3 SODIMM IIC
FMC LPC
BANK33
BANK34
BANK32
DVI Codec
VGA Video
DVI Video Connector
VITA 57.1 FMC
LPC Connector
Virtex-6
FPGA
XC6VLX240T - 1FFG1156
10/100/1000
Ethernet PHY
MII/GMII/RMII
SODIMM Socket
204-pin, DDR3
Decoupling Caps
MEM Vterm
Regulator
BANK33
BANK116
BANK 25, 35
BANK 26, 36
BANK114
BANK115
BANK14, 33, 36
User LED/SW
User DIP SW
User LCD
BANK24,34
200 MHz LVDS Clock
SMA Clock
User S.E. 2.5V Clock
BANK14
USB Controller
Host Type “A”
Peripheral Mini-B
Connectors
BANK24
SFP Module
Connector
SGMII
PCIe X8 Edge Connector
MGT SMA REF Clock
MGT RX/TX SMA Port
CP2103 USB-TO-UART
Bridge
USB Mini-B
UG534_01_092709
Figure 1-1:
ML605 High-Level Block Diagram
Related Xilinx Documents
Prior to using the ML605 Evaluation Board, users should be familiar with Xilinx resources.
See Appendix D, “References” for a direct link to Xilinx documentation. See the following
locations for additional documentation on Xilinx tools and solutions:
10
•
ISE: www.xilinx.com/ise
•
EDK: www.xilinx.com/edk
•
Intellectual Property: www.xilinx.com/ipcenter
•
Answer Browser: www.xilinx.com/support
www.xilinx.com
ML605 Hardware User Guide
UG534 (v1.2.1) January 21, 2010
Detailed Description
Detailed Description
Figure 1-2 shows a board photo with numbered features corresponding to Table 1-1 and
the section headings in this document.
X-Ref Target - Figure 1-2
20
17a
18a
13
19
13
21c
10
7b
17d
7c
17e
18d
18c
16c
23
16b
21d
5
2
18b
12
7d
6
16a
1
22
21a
21b
11
8
3
17f
14
17c
21a
8
4
17b
7a
9
(on backside)
15
Figure 1-2:
UG534_02_123009
ML605 Board Photo
The numbered features in Figure 1-2 correlate to the features and notes listed in Table 1-1.
Table 1-1:
Number
ML605 Features
Feature
Notes
Schematic
Page
1
Virtex-6 FPGA
XC6VLX240T-1FFG1156
2
DDR3 SODIMM
Micron 512 MB MT4JSF6464HY-1G1
15
3
128 Mb Platform Flash XL
Xilinx XCF128X-FTG64C
25
4
Linear BPI Flash
Numonyx JS28F256P30T95
26
5
System ACE CF controller, CF
connector
Xilinx XCCACE-TQ144I
(bottom of board)
13
6
JTAG cable connector (USB
Mini-B)
USB JTAG download circuit
46
ML605 Hardware User Guide
UG534 (v1.2.1) January 21, 2010
www.xilinx.com
2 - 12
11
Chapter 1: ML605 Evaluation Board
Table 1-1:
ML605 Features (Cont’d)
Notes
Schematic
Page
200 MHz OSC, oscillator socket, SMA
connectors
30
a. 200 MHz oscillator (on
backside)
Epson 200 MHz 2.5V LVDS OSC
30
b. Oscillator socket, singleended
MMD Components 66 MHz 2.5V
30
c. SMA connectors
SMA pair
30
d. MGT REFCLK SMA
connectors
SMA pair
30
Number
Feature
Clock generation
7
8
GTX RX/TX port
SMA x4
30
9
PCIe Gen1 (8-lane),
Gen2 (4-lane)
Card edge connector, 8-lane
21
10
SFP connector and cage
AMP 136073-1
23
11
Ethernet (10/100/1000) with
SGMII
Marvell M88E1111 EPHY
24
12
USB Mini-B, USB-to-UART
bridge
Silicon Labs CP2103GM bridge
33
13
USB-A Host, USB Mini-B
peripheral connectors
Cypress CY7C67300-100AXI
controller
27
14
Video - DVI connector
Chrontel CH7301C-TF Video codec
15
IIC NV EEPROM, 8 Kb
(on backside)
ST Microelectronics M24C08WDW6TP
Status LEDs
a. Ethernet status
Right-angle link rate and direction
LEDs
24
b. FPGA INIT, DONE
Init (red), Done (green)
31
c. System ACE CF status
Status (green), Error (red)
13
User I/O
12
32
13, 24, 31
16
17
28, 29
31
a. User LEDs, green (8)
User I/O (active-High)
30, 31, 33
b. User pushbuttons, N.O.
momentary (5)
User I/O (active-High)
31
c. User LEDs, green (5)
User I/O (active-High)
31
d. User DIP switch (8-pole) User I/O (active-High)
31
e. User GPIO SMA
connectors
SMA pair
30
f. LCD 16 character x 2 line
display
Displaytech S162D BA BC
33
www.xilinx.com
ML605 Hardware User Guide
UG534 (v1.2.1) January 21, 2010
Detailed Description
Table 1-1:
ML605 Features (Cont’d)
Number
Feature
Notes
Switches
18
Schematic
Page
13, 25, 39
a. Power On/Off
Slide switch
39
b. FPGA_PROG_B
pushbutton
active-Low
13
c. System ACE CF Image
Select
4-pole DIP switch (active-High)
25
d. Mode Switch
6-pole DIP switch (active-High)
25
19
FMC - HPC connector
Samtec ASP-134486-01
16 -19
20
FMC - LPC connector
Samtec ASP-134603-01
20
Power management
a. PMBus controllers
b. Voltage regulators
35 - 44
2 x TI UCD9240PFC
2 x PTD08A020W, 3 x PTD08A010W
21
35, 40
36-38, 43,
44
c. 12V power input
connector
6-pin Molex mini-fit connector
39
d. 12V power input
connector
4-pin ATX disk type connector
39
22
System Monitor Interface
connector
2x6 DIP male pin header
34
23
System ACE Error DS30 LED
disable jumper J69
Jumper on = enable LED
Jumper off = disable LED
13
1. Virtex-6 XC6VLX240T-1FFG1156 FPGA
A Virtex-6 XC6VLX240T-1FFG1156 FPGA is installed on the embedded development
board.
Keep-Out areas and drill holes are defined around the FPGA to support an Ironwood
Electronics SG-BGA-6046 FPGA socket.
References
See the Virtex-6 FPGA Data Sheet. [Ref 4]
Configuration
The ML605 supports configuration in the following modes:
•
Slave SelectMAP (using Platform Flash XL with the onboard 47 MHz oscillator)
•
Master BPI-Up (using Linear BPI Flash device)
•
JTAG (using the included USB-A to Mini-B cable)
•
JTAG (using System ACE CF and CompactFlash card)
ML605 Hardware User Guide
UG534 (v1.2.1) January 21, 2010
www.xilinx.com
13
Chapter 1: ML605 Evaluation Board
The ML605 supports Master BPI-Up, JTAG, and Slave SelectMAP. These are selected by
setting M[2:0] options 010, 101 and 110 shown in Table 1-2.
Table 1-2:
Virtex-6 FPGA Configuration Modes
M[2:0]
Bus Width(1)
CCLK Direction
Master Serial(2)
000
1
Output
Master SPI(2)
001
1
Output
Master BPI-Up(2)
010
8, 16
Output
Master BPI-Down(2)
011
8, 16
Output
Master SelectMAP(2)
100
8, 16
Output
JTAG
101
1
Input (TCK)
Slave SelectMAP
110
8, 16, 32
Input
Slave Serial(3)
111
1
Input
Configuration Mode
Notes:
1. The parallel configuration modes bus is auto-detected by the configuration logic.
2. In Master configuration mode, the CCLK pin is the clock source for the Virtex-6 FPGA internal
configuration logic. The Virtex-6 FPGA CCLK output pin must be free from reflections to avoid
double-clocking the internal configuration logic. See the Virtex-6 FPGA Configuration User Guide for
more details. [Ref 5]
3. This is the default setting due to internal pull-up termination on mode pins.
For an overview on configuring the FPGA, see “Configuration Options,” page 73.
Note: The mode switches are part of DIP switch S2. The default mode setting (see Table A-1,
page 75) is M[2:0]=010, which selects Master BPI-Up at board power-on. Switch S1 position 4 must
be OFF to disable the System ACE controller from attempting to boot if a CF card is present.
References
See the Virtex-6 FPGA Configuration User Guide for detailed configuration information.
[Ref 5]
I/O Voltage Rails
There are 16 I/O banks available on the Virtex-6 device. The voltage applied to the FPGA
I/O banks used by the ML605 board is summarized in Table 1-3.
Table 1-3:
Voltage Rails
U1 FPGA Bank
14
I/O Rail
Voltage
Bank 0
VCC2V5_FPGA
2.5V
Bank 12(1)
FMC_VIO_B_M2C
2.5V
Bank 13
VCC2V5_FPGA
2.5V
Bank 14
VCC2V5_FPGA
2.5V
Bank 15
VCC2V5_FPGA
2.5V
Bank 16
VCC2V5_FPGA
2.5V
Bank 22
VCC2V5_FPGA
2.5V
Bank 23
VCC2V5_FPGA
2.5V
www.xilinx.com
ML605 Hardware User Guide
UG534 (v1.2.1) January 21, 2010
Detailed Description
Table 1-3:
Voltage Rails (Cont’d)
U1 FPGA Bank
I/O Rail
Voltage
Bank 24
VCC2V5_FPGA
2.5V
Bank 25
VCC1V5_FPGA
1.5V
Bank 26
VCC1V5_FPGA
1.5V
Bank 32
VCC2V5_FPGA
2.5V
Bank 33
VCC2V5_FPGA
2.5V
Bank 34
VCC2V5_FPGA
2.5V
Bank 35
VCC1V5_FPGA
1.5V
Bank 36
VCC1V5_FPGA
1.5V
Notes:
1. The VITA 57.1 specification stipulates that the Bank 12 voltage named
FMC_VIO_B_M2C is supplied by the FMC card plugged onto the relevant
FMC connector (ML605 J64). FMC_VIO_B_M2C cannot exceed the base
board (ML605) Vadj of the FMC connector. The ML605 FMC Vadj
maximum is 2.5V.
References
See the Xilinx Virtex-6 FPGA documentation for more information at
http://www.xilinx.com/support/documentation/virtex-6.htm.
2. 512 MB DDR3 Memory SODIMM
A 512MB DDR3 SODIMM is provided as a flexible and efficient form-factor volatile
memory for user applications. The ML605 SODIMM socket is wired to support a
maximum SODIMM size of 2 GB.
The ML605 DDR3 64-bit wide interface has been tested to 800 MT/s.
The DDR3 interface is implemented in FPGA banks 25, 26, 35, and 36. DCI VRP/N resistor
connections are only implemented banks 26 and 36. DCI functionality in banks 25 and 35 is
achieved in the UCF by cascading DCI between adjacent banks as follows:
CONFIG DCI_CASCADE = "36 35";
CONFIG DCI_CASCADE = "26 25";
Table 1-4 shows the connections and pin numbers for the DDR3 SODIMM.
Table 1-4:
DDR3 SODIMM Connections
J1 SODIMM
U1 FPGA Pin
ML605 Hardware User Guide
UG534 (v1.2.1) January 21, 2010
Schematic Net Name
Pin Number
Pin Name
L14
DDR3_A0
98
A0
A16
DDR3_A1
97
A1
B16
DDR3_A2
96
A2
E16
DDR3_A3
95
A3
D16
DDR3_A4
92
A4
J17
DDR3_A5
91
A5
www.xilinx.com
15
Chapter 1: ML605 Evaluation Board
Table 1-4:
DDR3 SODIMM Connections (Cont’d)
J1 SODIMM
U1 FPGA Pin
16
Schematic Net Name
Pin Number
Pin Name
A15
DDR3_A6
90
A6
B15
DDR3_A7
86
A7
G15
DDR3_A8
89
A8
F15
DDR3_A9
85
A9
M16
DDR3_A10
107
A10/AP
M15
DDR3_A11
84
A11
H15
DDR3_A12
83
A12_BC_N
J15
DDR3_A13
119
A13
D15
DDR3_A14
80
A14
C15
DDR3_A15
78
A15
K19
DDR3_BA0
109
BA0
J19
DDR3_BA1
108
BA1
L15
DDR3_BA2
79
BA2
J11
DDR3_D0
5
DQ0
E13
DDR3_D1
7
DQ1
F13
DDR3_D2
15
DQ2
K11
DDR3_D3
17
DQ3
L11
DDR3_D4
4
DQ4
K13
DDR3_D5
6
DQ5
K12
DDR3_D6
16
DQ6
D11
DDR3_D7
18
DQ7
M13
DDR3_D8
21
DQ8
J14
DDR3_D9
23
DQ9
B13
DDR3_D10
33
DQ10
B12
DDR3_D11
35
DQ11
G10
DDR3_D12
22
DQ12
M11
DDR3_D13
24
DQ13
C12
DDR3_D14
34
DQ14
A11
DDR3_D15
36
DQ15
G11
DDR3_D16
39
DQ16
F11
DDR3_D17
41
DQ17
D14
DDR3_D18
51
DQ18
C14
DDR3_D19
53
DQ19
www.xilinx.com
ML605 Hardware User Guide
UG534 (v1.2.1) January 21, 2010
Detailed Description
Table 1-4:
DDR3 SODIMM Connections (Cont’d)
J1 SODIMM
U1 FPGA Pin
ML605 Hardware User Guide
UG534 (v1.2.1) January 21, 2010
Schematic Net Name
Pin Number
Pin Name
G12
DDR3_D20
40
DQ20
G13
DDR3_D21
42
DQ21
F14
DDR3_D22
50
DQ22
H14
DDR3_D23
52
DQ23
C19
DDR3_D24
57
DQ24
G20
DDR3_D25
59
DQ25
E19
DDR3_D26
67
DQ26
F20
DDR3_D27
69
DQ27
A20
DDR3_D28
56
DQ28
A21
DDR3_D29
58
DQ29
E22
DDR3_D30
68
DQ30
E23
DDR3_D31
70
DQ31
G21
DDR3_D32
129
DQ32
B21
DDR3_D33
131
DQ33
A23
DDR3_D34
141
DQ34
A24
DDR3_D35
143
DQ35
C20
DDR3_D36
130
DQ36
D20
DDR3_D37
132
DQ37
J20
DDR3_D38
140
DQ38
G22
DDR3_D39
142
DQ39
D26
DDR3_D40
147
DQ40
F26
DDR3_D41
149
DQ41
B26
DDR3_D42
157
DQ42
E26
DDR3_D43
159
DQ43
C24
DDR3_D44
146
DQ44
D25
DDR3_D45
148
DQ45
D27
DDR3_D46
158
DQ46
C25
DDR3_D47
160
DQ47
C27
DDR3_D48
163
DQ48
B28
DDR3_D49
165
DQ49
D29
DDR3_D50
175
DQ50
B27
DDR3_D51
177
DQ51
G27
DDR3_D52
164
DQ52
A28
DDR3_D53
166
DQ53
www.xilinx.com
17
Chapter 1: ML605 Evaluation Board
Table 1-4:
DDR3 SODIMM Connections (Cont’d)
J1 SODIMM
U1 FPGA Pin
18
Schematic Net Name
Pin Number
Pin Name
E24
DDR3_D54
174
DQ54
G25
DDR3_D55
176
DQ55
F28
DDR3_D56
181
DQ56
B31
DDR3_D57
183
DQ57
H29
DDR3_D58
191
DQ58
H28
DDR3_D59
193
DQ59
B30
DDR3_D60
180
DQ60
A30
DDR3_D61
182
DQ61
E29
DDR3_D62
192
DQ62
F29
DDR3_D63
194
DQ63
E11
DDR3_DM0
11
DM0
B11
DDR3_DM1
28
DM1
E14
DDR3_DM2
46
DM2
D19
DDR3_DM3
63
DM3
B22
DDR3_DM4
136
DM4
A26
DDR3_DM5
153
DM5
A29
DDR3_DM6
170
DM6
A31
DDR3_DM7
187
DM7
E12
DDR3_DQS0_N
10
DQS0_N
D12
DDR3_DQS0_P
12
DQS0_P
J12
DDR3_DQS1_N
27
DQS1_N
H12
DDR3_DQS1_P
29
DQS1_P
A14
DDR3_DQS2_N
45
DQS2_N
A13
DDR3_DQS2_P
47
DQS2_P
H20
DDR3_DQS3_N
62
DQS3_N
H19
DDR3_DQS3_P
64
DQS3_P
C23
DDR3_DQS4_N
135
DQS4_N
B23
DDR3_DQS4_P
137
DQS4_P
A25
DDR3_DQS5_N
152
DQS5_N
B25
DDR3_DQS5_P
154
DQS5_P
G28
DDR3_DQS6_N
169
DQS6_N
H27
DDR3_DQS6_P
171
DQS6_P
D30
DDR3_DQS7_N
186
DQS7_N
www.xilinx.com
ML605 Hardware User Guide
UG534 (v1.2.1) January 21, 2010
Detailed Description
Table 1-4:
DDR3 SODIMM Connections (Cont’d)
J1 SODIMM
U1 FPGA Pin
Schematic Net Name
Pin Number
Pin Name
C30
DDR3_DQS7_P
188
DQS7_P
F18
DDR3_ODT0
116
ODT0
E17
DDR3_ODT1
120
ODT1
E18
DDR3_RESET_B
30
RESET_B
K18
DDR3_S0_B
114
S0_B
K17
DDR3_S1_B
121
S1_B
D17
DDR3_TEMP_EVENT
198
EVENT_B
B17
DDR3_WE_B
113
WE_B
C17
DDR3_CAS_B
115
CAS_B
L19
DDR3_RAS_B
110
RAS_B
M18
DDR3_CKE0
73
CKE0
M17
DDR3_CKE1
74
CKE1
H18
DDR3_CLK0_N
103
CK0_N
G18
DDR3_CLK0_P
101
CK0_P
L16
DDR3_CLK1_N
104
CK1_N
K16
DDR3_CLK1_P
102
CK1_P
The Memory Interface Generator (MIG) tool guidelines specify a set of U1 FPGA “No
Connect” pins. These should be added to the UCF as CONFIG PROHIBIT pins as follows:
CONFIG
CONFIG
CONFIG
CONFIG
PROHIBIT
PROHIBIT
PROHIBIT
PROHIBIT
=
=
=
=
H22;
F21;
B20;
F19;
CONFIG
CONFIG
CONFIG
CONFIG
PROHIBIT
PROHIBIT
PROHIBIT
PROHIBIT
=
=
=
=
C13;
M12;
L13;
K14;
CONFIG
CONFIG
CONFIG
CONFIG
PROHIBIT
PROHIBIT
PROHIBIT
PROHIBIT
=
=
=
=
F25;
C29;
C28;
D24;
References
See the Micron Technology, Inc. for more information [Ref 22].
In addition, see the Virtex-6 FPGA Memory Interface Solutions User Guide [Ref 6] and the
Virtex-6 FPGA Memory Resources User Guide [Ref 9].
ML605 Hardware User Guide
UG534 (v1.2.1) January 21, 2010
www.xilinx.com
19
Chapter 1: ML605 Evaluation Board
3. 128 Mb Platform Flash XL
A 128 Mb Xilinx XCF128X-FTG64C Platform Flash XL device is used with an onboard
47 MHz oscillator (X4) to configure the FPGA in less than 100 ms from power valid as
required by the PCI Express Card Electromechanical Specification. This allows the PCIe
interface to be recognized and enumerated when plugged into a host PC.
To achieve the fastest configuration speed, the FPGA mode pins are set to Slave SelectMAP
and the onboard 47 MHz clock source external to the FPGA is used for configuration.
Configuration DIP switch S2, switch 1, controls the 47 MHz oscillator enable as outlined in
“18. Switches,” page 53.
See S2 switch setting details in Table 1-26, page 56. Also, see the “FPGA Design
Considerations for the Configuration Flash,” page 23 for FPGA design recommendations.
4. 32 MB Linear BPI Flash
A Numonyx JS28F256P30 Linear BPI Flash memory (P30) on the ML605 provides 32 MB of
non-volatile storage that can be used for configuration as well as software storage. The
Linear BPI Flash shares the dual use configuration pins in parallel with the XCF128
Platform Flash XL.
The P30_CS net is used to select the P30 or the XCF128. Power-on configuration is selected
by the P30_CS net which is tied to a dip switch S2 (selects pullup/pulldown) and is also
wired to an FPGA non-config pin. The dip switch allows power selection for the
configuration device P30 or XCF128XL. The dip switch selection can be overridden by the
FPGA after configuration by controlling the logic level of the P30_CS signal.
See S2 switch setting details in Table 1-26, page 56. For an overview on configuring the
FPGA, see “Configuration Options,” page 73.
Figure 1-3 shows a block diagram for the Platform Flash and BPI Flash.
X-Ref Target - Figure 1-3
U27
S1 Switch 4
OFF = Disable System ACE,
enable U4/U27 flash boot
ON = Enable System ACE boot when
CF card is present
PLATFORM
FLASH
FPGA U1
Bank 34
FLASH_A[22:0]
A
D
CE
S2 SWITCH 6
ON = U4 BPI Upper Half
OFF = U4 BPI Lower Half
FPGA U1
Bank 24
510
BPI
FLASH
S2-2
2
11
1
S2 SWITCH 2
ON = U4 BOOT
OFF = U27 BOOT
4.7K
VCC2V5
510
P30_CS_SEL
(FPGA U1 pin AJ12)
VCC2V5
U4
FLASH_A[23]
FLASH_D[15:0]
FPGA U1
VCC2V5
Bank 24
U10
6
PLATFLASH_FCS_B
S2-6
6
7
A
D
A23
E
4.7K
VCC2V5
4
FLASH_CE_B
3
FPGA_FCS_B FPGA U1
Bank 24
UG534_03_011110
Figure 1-3:
20
Platform Flash and BPI Flash Block Diagram
www.xilinx.com
ML605 Hardware User Guide
UG534 (v1.2.1) January 21, 2010
Detailed Description
ML605 Flash Boot Options
The ML605 has two parallel wired flash memory devices as shown in Figure 1-3. At ML605
power-up, before FPGA configuration, DIP switch S2 switch 2 selects which flash device,
U4 (BPI) or U27 (Platform Flash), provides the boot bitstream. Typically S2 switch 2 will be
open/OFF to select the U27 Platform Flash. Given that the mode switches (S2 switch
3/M0, switch 4/M1 and switch 5/M2) are set to Slave SelectMAP mode, then U27, driven
at 47 MHz, can load a PCIe core bitstream before a host PC motherboard can scan its PCIe
slots.When S2 switch 2 is closed/ON at power up, the FPGA will be configured from the
BPI flash device U4. Note that U4 address bit A23 is switched by S2 switch 6, which allows
the lower or upper half of U4 to be chosen as a data source.
Table 1-5 shows the connections and pin numbers for the boot flash devices.
Table 1-5:
Platform Flash and BPI Flash Connections
U4 BPI Flash
U1 FPGA Pin
U27 Platform Flash
Schematic Net Name
Pin Number
Pin Name
Pin Number
Pin Name
AL8
FLASH_A0
29
A1
A1
A00
AK8
FLASH_A1
25
A2
B1
A01
AC9
FLASH_A2
24
A3
C1
A02
AD10
FLASH_A3
23
A4
D1
A03
C8
FLASH_A4
22
A5
D2
A04
B8
FLASH_A5
21
A6
A2
A05
E9
FLASH_A6
20
A7
C2
A06
E8
FLASH_A7
19
A8
A3
A07
A8
FLASH_A8
8
A9
B3
A08
A9
FLASH_A9
7
A10
C3
A09
D9
FLASH_A10
6
A11
D3
A10
C9
FLASH_A11
5
A12
C4
A11
D10
FLASH_A12
4
A13
A5
A12
C10
FLASH_A13
3
A14
B5
A13
F10
FLASH_A14
2
A15
C5
A14
F9
FLASH_A15
1
A16
D7
A15
AH8
FLASH_A16
55
A17
D8
A16
AG8
FLASH_A17
18
A18
A7
A17
AP9
FLASH_A18
17
A19
B7
A18
AN9
FLASH_A19
16
A20
C7
A19
AF10
FLASH_A20
11
A21
C8
A20
AF9
FLASH_A21
10
A22
A8
A21
AL9
FLASH_A22
9
A23
G1
A22
AA23
FLASH_A23
26
A24
NC
A23
ML605 Hardware User Guide
UG534 (v1.2.1) January 21, 2010
www.xilinx.com
21
Chapter 1: ML605 Evaluation Board
Table 1-5:
Platform Flash and BPI Flash Connections (Cont’d)
U4 BPI Flash
U1 FPGA Pin
U27 Platform Flash
Schematic Net Name
Pin Number
Pin Name
Pin Number
Pin Name
AF24
FLASH_D0
34
DQ0
F2
DQ00
AF25
FLASH_D1
36
DQ1
E2
DQ01
W24
FLASH_D2
39
DQ2
G3
DQ02
V24
FLASH_D3
41
DQ3
E4
DQ03
H24
FLASH_D4
47
DQ4
E5
DQ04
H25
FLASH_D5
49
DQ5
G5
DQ05
P24
FLASH_D6
51
DQ6
G6
DQ06
R24
FLASH_D7
53
DQ7
H7
DQ07
G23
FLASH_D8
35
DQ8
E1
DQ08
H23
FLASH_D9
37
DQ9
E3
DQ09
N24
FLASH_D10
40
DQ10
F3
DQ10
N23
FLASH_D11
42
DQ11
F4
DQ11
F23
FLASH_D12
48
DQ12
F5
DQ12
F24
FLASH_D13
50
DQ13
H5
DQ13
L24
FLASH_D14
52
DQ14
G7
DQ14
M23
FLASH_D15
54
DQ15
E7
DQ15
J26
FLASH_WAIT
56
WAIT
NA(1)
NA(1)
AF23
FPGA_FWE_B
14
/WE
G8
/W
AA24
FPGA_FOE_B
32
/OE
F8
/G
K8
FPGA_CCLK
NA(1)
NA(1)
F1
K
AC23
PLATFLASH_L_B
NA(1)
NA(1)
H1
/L
Y24
FPGA_FCS_B(2)
NA(1)
NA(1)
NA(1)
NA(1)
NA(1)
PLATFLASH_FCS_B(3)
NA(1)
NA(1)
B4
/E
NA(1)
FLASH_CE_B(4)
30
/OE
NA(1)
NA(1)
Notes:
1.
2.
3.
4.
22
Not Applicable
FPGA control flash memory select signal connected to pin U10.3
Platform Flash select signal connected to pin U10.6
BPI Flash select signal connected to pin U10.4
www.xilinx.com
ML605 Hardware User Guide
UG534 (v1.2.1) January 21, 2010
Detailed Description
FPGA Design Considerations for the Configuration Flash
After FPGA configuration, the FPGA design can disable the configuration flash or access
the configuration flash to read/write code or data.
When the FPGA design does not use the configuration flash, the FPGA design must drive
the FPGA FCS_B pin High in order to disable the configuration flash and put the flash into
a quiescent, low-power state. Otherwise, the Platform Flash XL, in particular, can continue
to drive its array data onto the data bus causing unnecessary switching noise and power
consumption.
For FPGA designs that access the flash for reading/writing stored code or data, connect
the FPGA design or EDK embedded memory controller (EMC) peripheral to the flash
through the pins defined in Table 1-5, page 21.
The Platform Flash XL defaults to a synchronous read mode. Typically, the Platform Flash
XL requires an initialization procedure to put the Platform Flash XL into the common,
asynchronous read mode before accessing stored code or data. To put the Platform Flash
XL into asynchronous read mode, apply the Set Configuration Register command
sequence. See the Platform Flash XL High-Density Configuration and Storage Device Data Sheet
for details on the Set Configuration Register command. [Ref 17]
References
See the Numonyx StrataFlash Embedded Memory Data Sheet. [Ref 24]
Visit the Xilinx Platform Flash product page and click the Resources tab for more
information.
Also, see the Platform Flash XL High-Density Configuration and Storage Device Data Sheet
[Ref 17] and the Virtex-6 Configuration User Guide [Ref 10].
ML605 Hardware User Guide
UG534 (v1.2.1) January 21, 2010
www.xilinx.com
23
Chapter 1: ML605 Evaluation Board
5. System ACE CF and CompactFlash Connector
The Xilinx System ACE CompactFlash (CF) configuration controller allows a Type I or
Type II CompactFlash card to program the FPGA through the JTAG port. Both hardware
and software data can be downloaded through the JTAG port. The System ACE CF
controller supports up to eight configuration images on a single CompactFlash card. The
configuration address switches allow the user to choose which of the eight configuration
images to use.
The CompactFlash (CF) card shipped with the board is correctly formatted to enable the
System ACE CF controller to access the data stored in the card. The System ACE CF
controller requires a FAT16 file system, with only one reserved sector permitted, and a
sector-per-cluster size of more than one (UnitSize greater than 512). The FAT16 file system
supports partitions of up to 2 GB. If multiple partitions are used, the System ACE CF
directory structure must reside in the first partition on the CompactFlash, with the
xilinx.sys file located in the root directory. The xilinx.sys file is used by the System
ACE CF controller to define the project directory structure, which consists of one main
folder containing eight sub-folders used to store the eight ACE files containing the
configuration images. Only one ACE file should exist within each sub-folder. All folder
names must be compliant to the DOS 8.3 short file name format. This means that the folder
names can be up to eight characters long, and cannot contain the following reserved
characters: < > " / \ |. This DOS 8.3 file name restriction does not apply to the actual ACE
file names. Other folders and files may also coexist with the System ACE CF project within
the FAT16 partition. However, the root directory must not contain more than a total of 16
folder and/or file entries, including deleted entries. When ejecting or unplugging the
CompactFlash device, it is important to safely stop any read or write access to the
CompactFlash device to avoid data corruption.
System ACE CF error and status LEDs indicate the operational state of the System ACE CF
controller:
•
A blinking red error LED indicates that no CompactFlash card is present.
•
A solid red error LED indicates an error condition during configuration.
•
A blinking green status LED indicates a configuration operation is ongoing.
•
A solid green status LED indicates a successful download.
Note: Jumper J69 can be removed to disable the Red Error LED circuit. It is recommended that this
jumper is installed during operations utilizing the CompactFlash card.
Every time a CompactFlash card is inserted into the System ACE CF socket, a
configuration operation is initiated. Pressing the System ACE CF reset button re-programs
the FPGA.
Note: System ACE CF configuration is enabled by way of DIP switch S1. See “18. Switches,”
page 53 for more details.
The System ACE CF MPU port is connected to the FPGA. This connection allows the FPGA
to use the System ACE CF controller to reconfigure the system or access the CompactFlash
card as a generic FAT file system.
24
www.xilinx.com
ML605 Hardware User Guide
UG534 (v1.2.1) January 21, 2010
Detailed Description
Table 1-6 lists the System ACE CF connections.
Table 1-6:
System ACE CF Connections
U19 XCCACETQ144I
U1 FPGA Pin
Schematic Net Name
Pin Number
Pin Name
AM15
SYSACE_D0
66
MPD00
AJ17
SYSACE_D1
65
MPD01
AJ16
SYSACE_D2
63
MPD02
AP16
SYSACE_D3
62
MPD03
AG16
SYSACE_D4
61
MPD04
AH15
SYSACE_D5
60
MPD05
AF16
SYSACE_D6
59
MPD06
AN15
SYSACE_D7
58
MPD07
AC15
SYSACE_MPA00
70
MPA00
AP15
SYSACE_MPA01
69
MPA01
AG17
SYSACE_MPA02
68
MPA02
AH17
SYSACE_MPA03
67
MPA03
AG15
SYSACE_MPA04
45
MPA04
AF15
SYSACE_MPA05
44
MPA05
AK14
SYSACE_MPA06
43
MPA06
AJ15
SYSACE_MPBRDY
39
MPBRDY
AJ14
SYSACE_MPCE
42
MPCE
L9
SYSACE_MPIRQ
41
MPIRQ
AL15
SYSACE_MPOE
77
MPOE
AL14
SYSACE_MPWE
76
MPWE
AC8
SYSACE_CFGTDI
81
CFGTDI
AE8
FPGA_TCK
80
CFGTCK
AD8
FPGA_TDI
82
CFGTDO
AF8
FPGA_TMS
85
CFGTMS
AE16
CLK_33MHZ_SYSACE(1)
93
CLK
Notes:
1. The System ACE CF clock is sourced from U28 32.000 MHz osc.
References
See the System ACE CF product page and the System ACE CompactFlash Solution Data Sheet.
[Ref 18]
ML605 Hardware User Guide
UG534 (v1.2.1) January 21, 2010
www.xilinx.com
25
Chapter 1: ML605 Evaluation Board
6. USB JTAG
JTAG configuration is provided through onboard USB-to-JTAG configuration logic where
a computer host accesses the ML605 JTAG chain through a Type-A (computer host side) to
Type-Mini-B (ML605 side) USB cable.
The JTAG chain of the board is illustrated in Figure 1-4. JTAG configuration is allowable at
any time under any mode pin setting. JTAG initiated configuration takes priority over the
mode pin settings.
X-Ref Target - Figure 1-4
J17
USB Mini-B
J22
J18
FMC HPC
TDI
3.3V
FMC LPC
TDI
TDO
J64
2.5V
System ACE CF
TDO
TSTTDI
J63
CFGTDO
FPGA
TDI
U1
U19
TSTTDO
CFGTDI
TDO
UG534_04_081309
Figure 1-4:
JTAG Chain Diagram
FMC bypass jumpers J17 and J18 must be connected between pins 1-2 (bypass) to enable
JTAG access to the FPGA on the basic ML605 board (without FMC expansion modules
installed), as shown in Figure 1-5 and Figure 1-6. When either or both VITA 57.1 FMC
expansion connectors are populated with an expansion module that has a JTAG chain, the
respective jumper(s) must be set to connect pins 2-3 in order to include the FMC expansion
module's JTAG chain in the main ML605 JTAG chain.
X-Ref Target - Figure 1-5
J17
1
FMC_TDI_BUF
Bypass FMC HPC J64 = Jumper 1-2
2
FMC_LPC_TDI
Include FMC HPC J64 = Jumper 2-3
3
FMC_HPC_TDO
H - 1x3
UG534_05_081309
Figure 1-5:
VITA 57.1 FMC HPC (J64) JTAG Bypass Jumper J17
X-Ref Target - Figure 1-6
J18
1
FMC_LPC_TDI
Bypass FMC LPC J63 = Jumper 1-2
2
SYSACE_TDI
Include FMC LPC J63 = Jumper 2-3
3
FMC_LPC_TDO
H - 1x3
UG534_06_081309
Figure 1-6:
26
VITA 57.1 FMC LPC (J63) JTAG Bypass Jumper J18
www.xilinx.com
ML605 Hardware User Guide
UG534 (v1.2.1) January 21, 2010
Detailed Description
The JTAG chain can be used to program the FPGA and access the FPGA for hardware and
software debug.
The JTAG connector (USB Mini-B J22) allows a host computer to download bitstreams to
the FPGA using the Xilinx iMPACT software tool. In addition, the JTAG connector allows
debug tools such as the ChipScope™ Pro Analyzer tool or a software debugger to access
the FPGA. The iMPACT software tool can also program the BPI flash via the USB J22
connection. iMPACT can download a temporary design to the FPGA through the JTAG.
This provides a connection within the FPGA from the FPGA's JTAG port to the FPGA's BPI
interface. Through the connection made by the temporary design in the FPGA, iMPACT
can indirectly program the BPI flash or the Platform Flash XL from the JTAG USB J22
connector.
For an overview on configuring the FPGA, see “Configuration Options,” page 73.
7. Clock Generation
There are three FPGA fabric clock sources available on the ML605.
Oscillator (Differential)
The ML605 has one 2.5V LVDS differential 200 MHz oscillator (U11) soldered onto the
board and wired to an FPGA global clock input.
•
Crystal oscillator: Epson EG-2121CA-200.0000M-LHPA
•
PPM frequency jitter: 50 ppm
For more details, see the Epson EG-2121CA data sheet. [Ref 25].
Oscillator Socket (Single-Ended, 2.5V)
One populated single-ended clock socket (X5) is provided for user applications. The option
of 3.3V or 2.5V power may be selected via a 0 ohm resistor selection. The X5 socket is
populated with a 66 MHz 2.5V single-ended MMD Components MBH2100H-66.000 MHz
oscillator.
For more details, see the MMD Components MBH Series Data Sheet. [Ref 26]
ML605 Hardware User Guide
UG534 (v1.2.1) January 21, 2010
www.xilinx.com
27
Chapter 1: ML605 Evaluation Board
X-Ref Target - Figure 1-7
Silkscreened outline
has beveled corner
Socket has notch
in crossbar
UG534_07_092109
Figure 1-7: ML605 Oscillator Socket Pin 1 Location Identifiers
28
www.xilinx.com
ML605 Hardware User Guide
UG534 (v1.2.1) January 21, 2010
Detailed Description
X-Ref Target - Figure 1-8
Oscillator body has
one square corner
Oscillator top has
corner dot marking
UG534_08_092109
Figure 1-8:
ML605 Oscillator Pin 1 Location Identifiers
SMA Connectors (Differential)
A high-precision clock signal can be provided to the FPGA using differential clock signals
through the onboard 50-ohm SMA connectors J58(P)/J55(N).
ML605 Hardware User Guide
UG534 (v1.2.1) January 21, 2010
www.xilinx.com
29
Chapter 1: ML605 Evaluation Board
GTX SMA Clock
The ML605 includes a pair of SMA connectors for a GTX (MGT) Clock as described in
Figure 1-9 and Table 1-7.
X-Ref Target - Figure 1-9
C61 1
0.1UF
10V 2
X5R
J30 32K10K-400E3
SMA_REFCLK_C_N1
SMA_REFCLK_N
SMA_REFCLK_P
GND1
GND2
GND3
SIG GND4
GND5
GND6
GND7
2
3
4
5
6
7
8
C62 1
0.1UF
10V 2
X5R
J31 32K10K-400E3
SMA_REFCLK_C_P1
GND1
GND2
GND3
SIG GND4
GND5
GND6
GND7
2
3
4
5
6
7
8
UG534_09_081309
Figure 1-9:
Table 1-7:
30
GTX SMA Clock
GTX SMA Clock Connections
U1 FPGA Pin
Schematic Net Name
SMA Pin
F5
SMA_REFCLK_N
J30.1
F6
SMA_REFCLK_P
J31.1
www.xilinx.com
ML605 Hardware User Guide
UG534 (v1.2.1) January 21, 2010
Detailed Description
8. Multi-Gigabit Transceivers (GTX MGTs)
The ML605 provides access to 20 MGTs.
•
Eight (8) of the MGTs are wired to the PCIe x8 Endpoint (P1) edge connector fingers
•
Eight (8) of the MGTs are wired to the FMC HPC connector (J64)
•
One (1) MGT is wired to SMA connectors (J26, J27)
•
One (1) MGTs is wired to the FMC LPC connector (J63)
•
One (1) MGT is wired to the SFP Module connector (P4)
•
One (1) MGT is used for an SGMII connection to the Ethernet PHY (U80)
X-Ref Target - Figure 1-10
Note: xxxMHz = user specified frequency
SGMII 125 MHz LVDS
SMA xxx MHz LVDS
REFCLK0
REFCLK1
GTX_X0Y17
FMC#2 LPC xxxMHz GBTCLK0 LVDS
AC coupling on Mezz
BANK_116
GTX_X0Y19
GTX_X0Y18
GTX_X0Y16
GTX_X0Y14
REFCLK0
100 MHz LVDS
REFCLK1
GTX_X0Y13
100 MHz in from
PCIe Fingers
ICS
854104
GTX_X0Y12
GTX_X0Y11
GTX_X0Y10
No Connect
REFCLK0
No Connect
No Connect
REFCLK1
GTX_X0Y09
BANK_114
(HCSL)
250 MHz LVDS
ICS874001
BANK_115
GTX_X0Y15
GTX_X0Y08
GTX_X0Y06
(LVDS)
REFCLK0
FMC#1 HPC CLK2_M2C
(LVDS)
ICS
854104
REFCLK1
GTX_X0Y05
To FPGA CLK2_M2C_IO CC pin
BANK_113
GTX_X0Y07
FMC#1 HPC xxx MHz LVDS GBTCLK0
AC coupling on Mezz
GTX_X0Y04
GTX_X0Y02
(LVDS)
REFCLK0
FMC#1 HPC CLK3_M2C
(LVDS)
ICS
854104
REFCLK1
GTX_X0Y01
To FPGA CLK3_M2C_IO CC pin
GTX_X0Y00
BANK_112
GTX_X0Y03
FMC#1 HPC xxx MHz LVDS GBTCLK1
AC coupling on Mezz
SGMII
SMA
SFP
FMC#2
PCIe Lane1
PCIe Lane 2
PCIe Lane 3
PCIe Lane 4
PCIe
PCIe Lane 5
PCIe Lane 6
PCIe Lane 7
PCIe Lane 8
FMC#1
FMC#1
FMC#1
FMC#1
PCIe
FMC#1
FMC#1
FMC#1
FMC#1
UG534_10_101409
Figure 1-10:
MGT Clocking
References
See the Virtex-6 FPGA GTX Transceivers User Guide. [Ref 12]
ML605 Hardware User Guide
UG534 (v1.2.1) January 21, 2010
www.xilinx.com
31
Chapter 1: ML605 Evaluation Board
9. PCI Express Endpoint Connectivity
The 8-lane PCIe edge connector performs data transfers at the rate of 2.5 GT/s for a Gen1
application and 5.0 GT/s for a Gen2 application. The Virtex FPGA GTX MGTs are used for
the multi-gigabit per second serial interfaces.
The ML605 board trace impedance on all PCIe lanes supports both Gen1 and Gen2
applications. The ML605 supports up to Gen1 x8 and Gen2 x4 as shipped with a -1 speed
grade for the LX240T device.
Figure 1-11, page 32 is a diagram of the PCIe MGT bank 114 and 115 clocking.
X-Ref Target - Figure 1-11
Note: PCIe edge connector signal nomenclature is
from perspective of the system/motherboard.
P1
U14
U9
Q1/NQ1 PCIE_100M_MGT1_P/N CLK/NCLK Q/NQ
REFCLK+,-
PCIE_CLK_Q0_P/N CLK/NCLK
Q0/NQ0
ICS874001
ICS854104
PCIE_100M_MGT0_C_P/N
PCIE_250M_MGT1_C_P/N
PCIE_100M_MGT0_P/N
PCIE_250M_MGT1_P/N
U1
U1
Bank 115
Bank 114
MGTREFCLK0 P/N
MGTREFCLK0 P/N
PERp,n[7:0]
PETp,n[7:0]
MGTTX
P/N[3:0]
PCIe
8-Lane
Edge
Connector
MGTRX
P/N[3:0]
MGTTX
P/N[7:4]
MGTRX
P/N[7:4]
PCIE_TX[7:0]_P/N
PCIE_RX[7:0]_P/N
UG534_11_100809
Figure 1-11:
PCIe MGT Banks 114 and 115 Clocking
PCIe lane width/size is selected via jumper J42 as shown in Figure 1-12. The default lane
size selection is 1-lane (J42 pins 1 and 2 jumpered).
X-Ref Target - Figure 1-12
J42
PCIE_PRSNT_X1
1
2
PCIE_PRSNT_X4
3
4
5
6
PCIE_PRSNT_X8
H-2X3
Figure 1-12:
32
PCIE_PRSNT_B
UG534_12_111709
PCIe Lane Size Select Jumper J42
www.xilinx.com
ML605 Hardware User Guide
UG534 (v1.2.1) January 21, 2010
Detailed Description
Table 1-8 shows the PCIe connector (P1) that provides up to 8-lane access through the GTX
transceivers to the Virtex-6 FPGA integrated Endpoint block for PCIe designs.
Table 1-8:
PCIe Edge Connector Connections
P1 PCIe Edge Connector
U1 FPGA
Pin
Schematic Net Name
F1
Description
Pin Number
Pin Name
PCIE_TXO_P
A16
PERp0
F2
PCIE_TXO_N
A17
PERn0
H1
PCIE_TX1_P
A21
PERp1
H2
PCIE_TX1_N
A22
PERn1
K1
PCIE_TX2_P
A25
PERp2
K2
PCIE_TX2_N
A26
PERn2
M1
PCIE_TX3_P
A29
PERp3
M2
PCIE_TX3_N
A30
PERn3
P1
PCIE_TX4_P
A35
PERp4
P2
PCIE_TX4_N
A36
PERn4
T1
PCIE_TX5_P
A39
PERp5
T2
PCIE_TX5_N
A40
PERn5
V1
PCIE_TX6_P
A43
PERp6
V2
PCIE_TX6_N
A44
PERn6
Y1
PCIE_TX7_P
A47
PERp7
Y2
PCIE_TX7_N
A48
PERn7
J3
PCIE_RXO_P
B14
PETp0
J4
PCIE_RXO_N
B15
PETn0
K5
PCIE_RX1_P
B19
PETp1
K6
PCIE_RX1_N
B20
PETn1
L3
PCIE_RX2_P
B23
PETp2
L4
PCIE_RX2_N
B24
PETn2
N3
PCIE_RX3_P
B27
PETp3
N4
PCIE_RX3_N
B28
PETn3
R3
PCIE_RX4_P
B33
PETp4
R4
PCIE_RX4_N
B34
PETn4
U3
PCIE_RX5_P
B37
PETp5
U4
PCIE_RX5_N
B38
PETn5
W3
PCIE_RX6_P
B41
PETp6
W4
PCIE_RX6_N
B42
PETn6
ML605 Hardware User Guide
UG534 (v1.2.1) January 21, 2010
www.xilinx.com
Package
Placement
Integrated Endpoint block
transmit pair
GTXE1_X0Y15
Integrated Endpoint block
transmit pair
GTXE1_X0Y14
Integrated Endpoint block
transmit pair
GTXE1_X0Y13
Integrated Endpoint block
transmit pair
GTXE1_X0Y11
Integrated Endpoint block
transmit pair
GTXE1_X0Y10
Integrated Endpoint block
transmit pair
GTXE1_X0Y9
Integrated Endpoint block
transmit pair
GTXE1_X0Y8
Integrated Endpoint block
transmit pair
GTXE1_X0Y7
Integrated Endpoint block
receive pair
GTXE1_X0Y15
Integrated Endpoint block
receive pair
GTXE1_X0Y14
Integrated Endpoint block
receive pair
GTXE1_X0Y13
Integrated Endpoint block
receive pair
GTXE1_X0Y11
Integrated Endpoint block
receive pair
GTXE1_X0Y10
Integrated Endpoint block
receive pair
GTXE1_X0Y9
Integrated Endpoint block
receive pair
GTXE1_X0Y8
33
Chapter 1: ML605 Evaluation Board
Table 1-8:
PCIe Edge Connector Connections (Cont’d)
P1 PCIe Edge Connector
U1 FPGA
Pin
Schematic Net Name
AA3
Description
Pin Number
Pin Name
PCIE_RX7_P
B45
PETp7
AA4
PCIE_RX7_N
B46
PETn7
P6
PCIE_100M_MGT0_P
U14.16
Q0
P5
PCIE_100M_MGT0_N
U14.15
NQ0
V6
PCIE_250M_MGT1_P
U9.18
Q
V5
PCIE_250M_MGT1_N
U9.17
NQ
U14.6
PCIE_CLK_QO_P
A13
REFCLK+
U14.7
PCIE_CLK_QO_N
A14
REFCLK-
Integrated Endpoint block
differential clock pair from PCIe
edge connector
J42.2,4,6
PCIE_PRSNT_B
A1
PRSNT#1
J42 Lane Size Select jumper
AD22
PCIE_WAKE_B
B11
WAKE#
Integrated Endpoint block wake
signal, not connected on ML605
board
AE13
PCIE_PERST_B
A11
PERST
Integrated Endpoint block reset
signal
Integrated Endpoint block
receive pair
Sourced from U14 ICS854104
clock driver
Sourced from U9 ICS874001
clock multiplier/driver
Package
Placement
GTXE1_X0Y7
GTXE1_X0Y6
GTXE1_X0Y4
Notes:
1.
2.
3.
4.
5.
PCIE_TXn_P/N pairs are capacitively coupled to FPGA
PCIE_100M_MGT0_P/N pairs are capacitively coupled to FPGA
PCIE_250M_MGT1_P/N pairs are capacitively coupled to FPGA
PCIE_PERST_B is level-shifted by U32
For ML605, access is through MGT Banks 114 and 115
The PCIe interface obtains its power from the DC power supply provided with the ML605
or through the 12V ATX power supply connector. The PCIe edge connector is not used for
any power connections.
The board can be powered by one of two 12V sources; J60, a 6-pin (2x3) molex-type
connector and J25, a 4-pin (inline) ATX disk drive type connector.
The 6-pin molex-type connector provides 60W (12V @ 5A) from the AC power adapter
provided with the board while the 4-pin ATX disk drive connector is provided for users
who want to power their board while it is installed inside a PC chassis.
For applications requiring additional power, such as the use of expansion cards drawing
significant power, a larger AC adapter might be required. If a different AC adapter is used,
its load regulation should be better than ±10%.
ML605 power switch SW2 turns the board on and off by controlling the 12V supply to the
board.
Caution! Never apply power to the power brick connector (J60) and the 4-pin ATX disk drive
connector (J25) at the same time as this will result in damage to the board. See Figure 1-23,
page 53. Never connect an auxiliary PCIe 6-pin molex power connector to J60 6-pin molex on
the ML605 board as this could result in damage to the PCIe motherboard and/or ML605 board.
The 6-pin molex connector is marked with a no PCIe power label to warn users of the potential
hazard.
34
www.xilinx.com
ML605 Hardware User Guide
UG534 (v1.2.1) January 21, 2010
Detailed Description
References
See the following websites for more Virtex-6 FPGA Integrated Endpoint Block for PCI
Express information:
•
http://www.xilinx.com/products/ipcenter/V6_PCI_Express_Block.htm
•
http://www.xilinx.com/support/documentation/ipbusinterfacei-o_pciexpress_v6pciexpressendpointblock.htm
In addition, see the PCI Express specifications for more information. [Ref 27]
10. SFP Module Connector
The board contains a small form-factor pluggable (SFP) connector and cage assembly that
accepts SFP modules. The SFP interface is connected to MGT Bank 116 on the FPGA. The
SFP module serial ID interface is connected to the "SFP" IIC bus (see “15. IIC Bus,” page 42
for more information). The control and status signals for the SFP module are connected to
jumpers and test points as described in Table 1-9. The SFP module connections are shown
in Table 1-10, page 36.
Table 1-9:
SFP Module Control and Status
SFP Control/Status
Signal
Board Connection
Test Point J52
SFP_TX_FAULT
High = Fault
Low = Normal Operation
Jumper J65
SFP_TX_DISABLE
Off = SFP Disabled
On = SFP Enabled
Test Point J53
SFP_MOD_DETECT
High = Module Not Present
Low = Module Present
Jumper J54
SFP_RT_SEL
Jumper Pins 1-2 = Full Bandwidth
Jumper Pins 2-3 = Reduced Bandwidth
Test Point J51
SFP_LOS
High = Loss of Receiver Signal
Low = Normal Operation
ML605 Hardware User Guide
UG534 (v1.2.1) January 21, 2010
www.xilinx.com
35
Chapter 1: ML605 Evaluation Board
Table 1-10:
SFP Module Connections
P4 SFP Module Connector
U1 FPGA Pin
Schematic Net Name
Pin Number
Pin Name
E3
SFP_RX_P
13
RDP_13
E4
SFP_RX_N
12
RDN_12
C3
SFP_TX_P
18
TDP_18
C4
SFP_TX_N
19
TDN_19
V23
SFP_LOS
8
LOS
AP12
SFP_TX_DISABLE(1)
3
TX_DISABLE
Notes:
1. The SFP TX Disable pin 3 is driven by transistor Q22, the base of which is driven
by the FPGA signal SFP_TX_DISABLE_FPGA.
11. 10/100/1000 Tri-Speed Ethernet PHY
The ML605 utilizes the onboard Marvell Alaska PHY device (88E1111) for Ethernet
communications at 10, 100, or 1000 Mb/s. The board supports MII, GMII, RGMII, and
SGMII interfaces from the FPGA to the PHY (Table 1-11). The PHY connection to a userprovided Ethernet cable is through a Halo HFJ11-1G01E RJ-45 connector with built-in
magnetics.
Table 1-11:
PHY Default Interface Mode
Jumper Settings
Mode
J66
J67
J68
GMII/MII to copper
(default)
Jumper over pins 1-2
Jumper over pins 1-2
No jumper
SGMII to copper,
no clock
Jumper over pins 2-3
Jumper over pins 2-3
No jumper
RGMII
Jumper over pins 1-2
No jumper
Jumper on
On power-up, or on reset, the PHY is configured to operate in GMII mode with PHY
address 0b00111 using the settings shown in Table 1-12. These settings can be overwritten
via software commands passed over the MDIO interface.
Table 1-12:
Pin
36
Board Connections for PHY Configuration Pins
Connection on
Bit[2]
Bit[1]
Bit[0]
Board
Definition and Value Definition and Value Definition and Value
CFG0
VCC 2.5V
PHYADR[2] = 1
PHYADR[1] = 1
PHYADR[0] = 1
CFG1
Ground
ENA_PAUSE = 0
PHYADR[4] = 0
PHYADR[3] = 0
CFG2
VCC 2.5V
ANEG[3] = 1
ANEG[2] = 1
ANEG[1] = 1
CFG3
VCC 2.5V
ANEG[0] = 1
ENA_XC = 1
DIS_125 = 1
CFG4
VCC 2.5V
HWCFG_MD[2] = 1
HWCFG_MD[1] = 1
HWCFG_MD[0] = 1
www.xilinx.com
ML605 Hardware User Guide
UG534 (v1.2.1) January 21, 2010
Detailed Description
Table 1-12:
Board Connections for PHY Configuration Pins (Cont’d)
Connection on
Bit[2]
Bit[1]
Bit[0]
Board
Definition and Value Definition and Value Definition and Value
Pin
CFG5
VCC 2.5V
DIS_FC = 1
DIS_SLEEP = 1
HWCFG_MD[3] = 1
CFG6
PHY_LED_RX
SEL_BDT = 0
INT_POL = 1
75/50 OHM = 0
SGMII GTX Transceiver Clock Generation
An Integrated Circuit Systems ICS844021I chip generates a high-quality, low-jitter, 125MHz LVDS clock from an inexpensive 25-MHz crystal oscillator. This clock is sent to the
GTX driving the SGMII interface. Series AC coupling capacitors are also present to allow
the clock input of the FPGA to set the common mode voltage.
X-Ref Target - Figure 1-13
VDDA_SGMIICLK
SGMIICLK_XTAL_OUT
3
SGMIICLK_XTAL_IN
4
1
Q0
GND
X3
1 R132
DNP
1%
2 1/16W
VDD
XTAL_OUT
NQ0
XTAL_IN
OE
C56 1
0.1UF
10V
2
X5R
VDDA
2
8
7
SGMIICLK_QO_C_P
6
SGMIICLK_QO_C_N
SGMIICLK_QO_N
5
U82
25.000MHZ
GND_SGMIICLK
SGMIICLK_QO_P
C55 1
0.1UF
10V
2
X5R
C348
33PF
2 50V
NPO
1
1
C347
33PF
2 50V
NPO
VDD_SGMIICLK
ICS84402II
125.00 MHz Clock
UG534_13_111709
Figure 1-13:
Ethernet SGMII Clock - 125 MHz
Table 1-13 shows the connections and pin numbers for the PHY.
Table 1-13:
Ethernet PHYConnections
U80 M88E1111
U1 FPGA Pin
Schematic Net Name
Pin Number
Pin Name
AN14
PHY_MDIO
33
MDIO
AP14
PHY_MDC
35
MDC
AH14
PHY_INT
32
INT_B
AH13
PHY_RESET
36
RESET_B
AL13
PHY_CRS
115
CRS
AK13
PHY_COL
114
COL
AP11
PHY_RXCLK
7
RXCLK
AG12
PHY_RXER
8
RXER
AM13
PHY_RXCTL_RXDV
4
RXDV
AN13
PHY_RXD0
3
RXD0
AF14
PHY_RXD1
128
RXD1
AE14
PHY_RXD2
126
RXD2
AN12
PHY_RXD3
125
RXD3
ML605 Hardware User Guide
UG534 (v1.2.1) January 21, 2010
www.xilinx.com
37
Chapter 1: ML605 Evaluation Board
Table 1-13:
Ethernet PHYConnections (Cont’d)
U80 M88E1111
U1 FPGA Pin
Schematic Net Name
Pin Number
Pin Name
AM12
PHY_RXD4
124
RXD4
AD11
PHY_RXD5
123
RXD5
AC12
PHY_RXD6
121
RXD6
AC13
PHY_RXD7
120
RXD7
AH12
PHY_TXC_GTXCLK
14
GTXCLK
AD12
PHY_TXCLK
10
TXCLK
AH10
PHY_TXER
13
TXER
AJ10
PHY_TXCTL_TXEN
16
TXEN
AM11
PHY_TXD0
18
TXD0
AL11
PHY_TXD1
19
TXD1
AG10
PHY_TXD2
20
TXD2
AG11
PHY_TXD3
24
TXD3
AL10
PHY_TXD4
25
TXD4
AM10
PHY_TXD5
26
TXD5
AE11
PHY_TXD6
28
TXD6
AF11
PHY_TXD7
29
TXD7
A3
SGMII_TX_P
113
SIN_P
A4
SGMII_TX_N
112
SIN_N
B5
SGMII_RX_P
107
SOUT_P
B6
SGMII_RX_N
105
SOUT_N
References
See the Marvell Alaska Gigabit Ethernet Transceivers product page for more information.
[Ref 28]
Also, see the LogiCORE™ IP Tri-Mode Ethernet MAC User Guide. [Ref 19]
38
www.xilinx.com
ML605 Hardware User Guide
UG534 (v1.2.1) January 21, 2010
Detailed Description
12. USB-to-UART Bridge
The ML605 contains a Silicon Labs CP2103GM USB-to-UART bridge device (U34) which
allows connection to a host computer with a USB cable. The USB cable is supplied in this
evaluation kit (Type A end to host computer, Type Mini-B end to ML605 connector J21).
Table 1-14 details the ML605 J21 pinout.
Xilinx UART IP is expected to be implemented in the FPGA fabric (for instance, Xilinx XPS
UART Lite. The FPGA supports the USB-to-UART bridge using four signal pins: Transmit
(TX), Receive (RX), Request to Send (RTS), and Clear to Send (CTS).
Silicon Labs provides royalty-free Virtual COM Port (VCP) drivers which permit the
CP2103GM USB-to-UART bridge to appear as a COM port to host computer
communications application software (for example, HyperTerm or TeraTerm). The VCP
device driver must be installed on the host PC prior to establishing communications with
the ML605. Refer to the evaluation kit Getting Started Guide for driver installation
instructions.
Table 1-14:
USB Type B Pin Assignments and Signal Definitions
USB Connector
Pin
Signal Name
Description
1
VBUS
+5V from host system (not used)
2
USB_DATA_N
Bidirectional differential serial data (N-side)
3
USB_DATA_P
Bidirectional differential serial data (P-side)
4
GROUND
Signal ground
Table 1-15:
USB-to-UART Connections
U1 FPGA Pin
UART function
in FPGA
Schematic Net
Name
U34 CP2103GM
Pin
UART Function
in CP2103GM
T24
RTS, output
USB_1_CTS
22
CTS, input
T23
CTS, input
USB_1_RTS
23
RTS, output
J25
TX, data out
USB_1_RX
24
RXD, data in
J24
RX, data in
USB_1_TX
25
TXD, data out
References
Refer to the Silicon Labs website for technical information on the CP2103GM and the VCP
drivers.
In addition, see some of the Xilinx UART IP specifications at:
•
http://www.xilinx.com/support/documentation/ip_documentation/xps_uartlite.pdf
•
http://www.xilinx.com/support/documentation/ip_documentation/xps_uart16550.pdf
ML605 Hardware User Guide
UG534 (v1.2.1) January 21, 2010
www.xilinx.com
39
Chapter 1: ML605 Evaluation Board
13. USB Controller
The ML605 provides USB support via a Cypress CY7C67300 EZ-Host™ Programmable
Embedded USB Host and Peripheral Controller (U81). The host port is a USB Type-A
connector (J5). A USB keyboard (without an internal USB hub) will be able to connect to
this USB Host port to demonstrate functionality. The peripheral port is a USB Type MiniB (J20).
Table 1-16:
USB Controller Connections
U81 USB Controller
U1 FPGA
Pin
Schematic Net Name
Y32
Pin
Number
Pin Name
USB_A0_LS
52
GPIO19_A0_CS0_52
W26
USB_A1_LS
50
50_GPIO20_A1_CS1
W27
USB_CS_B_LS
49
49_GPIO21_CS_N
R33
USB_D0_LS
94
GPIO0_D0_94
R34
USB_D1_LS
93
GPIO1_D1_93
T30
USB_D2_LS
92
GPIO2_D2_92
T31
USB_D3_LS
91
GPIO3_D3_91
T29
USB_D4_LS
90
GPIO4_D4_90
V28
USB_D5_LS
89
GPIO5_D5_89
V27
USB_D6_LS
87
GPIO6_D6_87
U25
USB_D7_LS
86
GPIO7_D7_86
Y28
USB_D8_LS
66
GPIO8_D8_MISO_66
W32
USB_D9_LS
65
GPIO9_D9_nSSI_65
W31
USB_D10_LS
61
GPIO10_D10_SCK_61
Y29
USB_D11_LS
60
GPIO11_D11_MOSI_60
W29
USB_D12_LS
59
GPIO12_D12_59
Y34
USB_D13_LS
58
GPIO13_D13_58
Y33
USB_D14_LS
57
GPIO14_D14_57
Y31
USB_D15_LS
56
GPIO15_D15_SSI_N_56
Y27
USB_INT_LS
46
46_GPIO24_INT_IORDY_IRQ0
W25
USB_RD_B_LS
47
47_GPIO23_RD_N_IOR
T25
USB_RESET_B_LS
85
RESET_N_85
V25
USB_WR_B_LS
48
48_GPIO22_WR_N_IOW
References
See the Cypress CY7C67300 Data Sheet for more information. [Ref 29]
In addition, see the USB Specifications for more information. [Ref 30]
The FPGA requires implementation of a peripheral controller in order to communicate
with the Cypress USB device. See the XPS External Peripheral Controller (EPC) v1.02a Data
Sheet for more information. [Ref 20]
40
www.xilinx.com
ML605 Hardware User Guide
UG534 (v1.2.1) January 21, 2010
Detailed Description
14. DVI Codec
The ML605 features a DVI connector (P3) to support an external video monitor. The DVI
circuitry utilizes a Chrontel CH7301C (U38) capable of 1600 X 1200 resolution with 24-bit
color. The video interface chip drives both the digital and analog signals to the DVI
connector. A DVI monitor can be connected to the board directly. A VGA monitor can also
be connected to the board using the supplied DVI-to-VGA adaptor. The Chrontel
CH7301C is controlled by way of the video IIC bus.
The DVI connector (Table 1-17) supports the IIC protocol to allow the board to read the
monitor's configuration parameters. These parameters can be read by the FPGA using the
DVI IIC bus (see “15. IIC Bus,” page 42).
Table 1-17:
DVI Controller Connections
U38 Chrontel CH7301C
U1 FPGA Pin Schematic Net Name
Pin Number
Pin Name
AJ19
DVI_D0
63
D0
AH19
DVI_D1
62
D1
AM17
DVI_D2
61
D2
AM16
DVI_D3
60
D3
AD17
DVI_D4
59
D4
AE17
DVI_D5
58
D5
AK18
DVI_D6
55
D6
AK17
DVI_D7
54
D7
AE18
DVI_D8
53
D8
AF18
DVI_D9
52
D9
AL16
DVI_D10
51
D10
AK16
DVI_D11
50
D11
AD16
DVI_DE
2
DE
AN17
DVI_H
4
H
AP17
DVI_RESET_B_LS
13
RESET_B
AD15
DVI_V
5
V
AC17
DVI_XCLK_N
56
XCLK_N
AC18
DVI_XCLK_P
57
XCLK_P
No Connect
DVI_GPIO0
8
GPIO0
No Connect
DVI_GPIO1
7
GPIO1
ML605 Hardware User Guide
UG534 (v1.2.1) January 21, 2010
www.xilinx.com
41
Chapter 1: ML605 Evaluation Board
15. IIC Bus
The ML605 implements four IIC bus interfaces at the FPGA.
The "MAIN" IIC bus hosts four items:
•
FPGA U1 Bank 34 "MAIN" IIC interface
•
8Kb NV Memory U6
•
FMC HPC connector J64
•
DDR3 SODIMM Socket J1
The "DVI" IIC bus hosts two items:
•
FPGA U1 Bank 34 "DVI" IIC interface
•
DVI codec U38 and DVI connector J63
The "LPC" IIC bus hosts two items:
•
FPGA U1 Bank 33 "LPC" IIC interface
•
FMC LPC connector J63
The "SFP" IIC bus hosts two items:
•
FPGA U1 Bank 13 "SFP" IIC interface
•
SFP module connector P4
The ML605 IIC bus topology is shown in Figure 1-14.
42
www.xilinx.com
ML605 Hardware User Guide
UG534 (v1.2.1) January 21, 2010
Detailed Description
X-Ref Target - Figure 1-14
U1
IIC_SDA_MAIN_LS
FPGA IIC
INTERFACE
BANK 34
BANK 13
BANK 34
IIC_SCL_MAIN_LS
IIC_SDA_SFP
IIC_SCL_SFP
IIC_SDA_DVI
LEVEL
SHIFTER
IIC_SCL_DVI
FMC_LPC_IIC_SDA_LS
BANK 33
FMC_LPC_IIC_SCL_LS
LEVEL
SHIFTER
J63
FMC LPC
COLUMN C
2 Kb EEPROM on
any FMC LPC
Mezzanine Card
Addr: 0b1010001
LEVEL
SHIFTER
LEVEL
SHIFTER
FMC_LPC_IIC_SCL
FMC_LPC_IIC_SDA
U6
ST MICRO
M24C08-WDW6TP
Addr: 0b1010100
through
0b1010111
J64
FMC HPC
COLUMN C
2 Kb EEPROM on
any FMC LPC
Mezzanine Card
Addr: 0b1010000
J1
P3
DVI CONN
DDR3 SODIMM
IIC_SCL_MAIN
SOCKET
Addr: 0b1010011
IIC_SDA_MAIN 2 Kb EEPROM
Addr: 0b0011011
Temperature Sensor
P4
SFP_MOD_DEF2
SFP MODULE
CONNECTOR
SFP_MOD_DEF1
Addr: 0b1010000
IIC_CLK_DVI_F
IIC_SDA_DVI_F
Addr: 0b1010000
U38
DVI CODEC
CHRONTEL
CH730C-TF
Addr: 0b1110110
UG534_14_092109
Figure 1-14:
ML605 Hardware User Guide
UG534 (v1.2.1) January 21, 2010
IIC Bus Topology
www.xilinx.com
43
Chapter 1: ML605 Evaluation Board
8 Kb NV Memory
The ML605 hosts an 8 Kb ST Microelectronics M24C08-WDW6TP IIC parameter storage
memory device (U6). The IIC address of U7 is 0b1010100, and U6 is not write protected
(WP pin 7 is tied to GND).
The IIC memory is shown in Figure 1-15.
X-Ref Target - Figure 1-15
VCC3V3
5%
R414
0
5%
1/16W
2
1
2
1
2
R413
0
5%
1/16W
IIC SCL MAIN
IIC SDA MAIN
0
R414
1
VCC3V3
U6
6
SCL
5
SDA
WP
1
A0
2
A1
3 A2
8
VCC
GND 4
VCC3V3
7
1
C65
X5R
10V
0.1UF
2
M24C08-WDW6TP
1
2
IIC Address = 0b1010100
R305
DNP
1%
1/16W
UG534_15_072109
Figure 1-15:
Table 1-18:
IIC Memory U6
IIC Memory Connections
IIC Memory U6
FPGA U1 Pin
Schematic Net Name
Pin Number
Pin Name
Not Applicable
Tied to GND
1
A0
Not Applicable
Tied to GND
2
A1
Not Applicable
Pulled up (0 ohm) to VCC3V3
3
A2
N10
IIC_SDA_MAIN
5
SDA
P11
IIC_SCL_MAIN
6
SCL
Tied to GND
7
WP
Not Applicable
References
See the ST Micro M24C08 Data Sheet for more information. [Ref 31]
In addition, see the Xilinx XPS IIC Bus Interface (v2.00a) Data Sheet. [Ref 21]
44
www.xilinx.com
ML605 Hardware User Guide
UG534 (v1.2.1) January 21, 2010
Detailed Description
16. Status LEDs
Table 1-19 defines the status LEDs.
Table 1-19:
Status LEDs
Designator
Signal Name
Color
Label
Description
DS1
SYSACE_STAT_LED
GREEN
System ACE CF
Status LED
System ACE CF Status
DS2
TI_PWRGOOD and
MGT_TI_PWRGOOD
GREEN
POWER GOOD
Both UCD9240 controllers
report power good
DS13
FPGA_DONE
GREEN
DONE
FPGA configured successfully
DS23
LED_GRN
GREEN
STATUS
LED_RED
RED
USB JTAG Connection Status
(Dual LED)
DS25
12V
GREEN
12V
12V Power On
DS27
MGT_AVCC
GREEN
AVCC GD
MGT AVCC Power On
DS28
MGT_AVTT
GREEN
MGT_AVTT
MGT AVTT Power On
DS29
DDR3_VTTDDR_PWRGOOD
GREEN
DDR3 PWR GD
DDR3 VTTDDR Power Good
DS30
SYSACE_ERR_LED
RED
System ACE CF
Error LED
System ACE CF Error
DS31
FPGA_INIT_B
RED
INIT
FPGA Initialization in progress
DS32
DVI_GPIO1_FMC_C2M_PG
FMC PWR GD
FMC Power Good
ML605 Hardware User Guide
UG534 (v1.2.1) January 21, 2010
GREEN
www.xilinx.com
45
Chapter 1: ML605 Evaluation Board
Ethernet PHY Status LEDs
The Ethernet PHY status LEDs are mounted to be visible when the ML605 board is
installed into a PC motherboard. They are mounted in right-angle, plastic housings and
can be seen on the connector end of the board. This cluster of six LEDs is installed adjacent
to the RJ45 Ethernet jack P2.
X-Ref Target - Figure 1-16
Direction
Indicator
Link Rate
(Mbps)
10
100
1000
DUP
TX
RX
P2
End view of ML605 Ethernet jack and
status LEDs when installed vertically
in a PC chassis
UG534_16_101209
Figure 1-16:
46
Ethernet PHY Status LEDs
www.xilinx.com
ML605 Hardware User Guide
UG534 (v1.2.1) January 21, 2010
Detailed Description
FPGA INIT and DONE LEDs
The typical Xilinx FPGA power up and configuration status LEDs are present on the
ML605.
The red INIT LED DS31 comes on momentarily after the FPGA powers up and during its
internal power-on process. The DONE LED DS13 comes on after the FPGA programming
bitstream has been downloaded and the FPGA successfully configured.
X-Ref Target - Figure 1-17
VCC2V5
VCC2V5
1
2
R419
330
5%
1/16W
Q14
FPGA INIT B
2
FPGA_DONE
1
R3
27.4
1%
1/16W
LED-GRN-SMT
DS13
2
2
LED-RED-SMT
DS31
1
1
1
2
3
NDS336P
1
2
R4
27.4
1%
1/16W
UG534_17_011310
Figure 1-17:
Table 1-20:
FPGA INIT and DONE LEDs
FPGA INIT and DONE LED Connections
FPGA U1 Pin
Schematic Net Name
Controlled LED
P8
FPGA_INIT_B
DS31 INIT, Red
R8
FPGA_DONE
DS13 DONE, Green
17. User I/O
The ML605 provides the following user and general purpose I/O capabilities:
•
User LEDs (8) with parallel wired GPIO male pin header
•
User Pushbutton (5) switches with associated direction LEDs
•
CPU Reset pushbutton switch
•
User DIP switch (8-pole)
•
User SMA GPIO
•
LCD Display (16 char x 2 lines)
ML605 Hardware User Guide
UG534 (v1.2.1) January 21, 2010
www.xilinx.com
47
Chapter 1: ML605 Evaluation Board
User LEDs
The ML605 provides two groups of active-High LEDs as described in Figure 1-18 and
Table 1-21.
X-Ref Target - Figure 1-18
J62
GPIO_LED_0
GPIO_LED_1
1
2
GPIO_LED_2
GPIO_LED_3
3
4
GPIO_LED_4
GPIO_LED_5
5
6
GPIO_LED_6
7
GPIO_LED_7
8
1
2
1
2
2
2
1
R8
27.4
1%
1/16W
2
2
1
1
1
R11
27.4
1%
1/16W
2
LED-GRN-SMT
DS12
2
2
1
R10
27.4
1%
1/16W
LED-GRN-SMT
DS11
2
1
R9
27.4
1%
1/16W
LED-GRN-SMT
DS9
1
DS10
2
1
1
1
R7
27.4
1%
1/16W
LED-GRN-SMT
2
1
LED-GRN-SMT
DS15
2
1
R6
27.4
1%
1/16W
LED-GRN-SMT
DS14
2
R5
27.4
1%
1/16W
LED-GRN-SMT
DS22
1
LED-GRN-SMT
1
DS21
2
H-1X8
R12
27.4
1%
1/16W
2
GPIO_LED_C
GPIO_LED_W
GPIO_LED_E
GPIO_LED_S
2
1 R16
27.4
1%
1/16W 2
1
27.4
1%
1/16W 2
LED-GRN-SMT
DS16
1
GPIO_LED_C_R
LED-GRN-SMT
1
GPIO_LED_W_R
2
2
1 R15
27.4
1%
1/16W 2
DS17
2
1
GPIO_LED_E_R
1 R14
27.4
1%
1/16W 2
LED-GRN-SMT
DS19
LED-GRN-SMT
1
DS18
2
1 R13
GPIO_LED_S_R
LED-GRN-SMT
DS20
1
GPIO_LED_N_R
This group of LEDs is mounted
adjacent to their respective “direction”
pushbuttons, as seen on the right side
of the LCD on the board photo (Figure
1-2).
2
GPIO_LED_N
R17
27.4
1%
1/16W
UG534_18_081109
Figure 1-18:
User LEDs and GPIO Connector, Directional LEDs
Note: See “User Pushbutton Switches,” page 49 for more details about the LEDs.
48
www.xilinx.com
ML605 Hardware User Guide
UG534 (v1.2.1) January 21, 2010
Detailed Description
Table 1-21:
User LED Connections
FPGA U1 Pin Schematic Net Name GPIO J62 Pin
Controlled LED
AC22
GPIO_LED_0
1
DS12
AC24
GPIO_LED_1
2
DS11
AE22
GPIO_LED_2
3
DS9
AE23
GPIO_LED_3
4
DS10
AB23
GPIO_LED_4
5
DS15
AG23
GPIO_LED_5
6
DS14
AE24
GPIO_LED_6
7
DS22
AD24
GPIO_LED_7
8
DS21
AP24
GPIO_LED_C
–
DS16
AD21
GPIO_LED_W
–
DS17
AE21
GPIO_LED_E
–
DS19
AH28
GPIO_LED_S
–
DS18
AH27
GPIO_LED_N
–
DS20
User Pushbutton Switches
The ML605 provides six active-High pushbutton switches:
•
SW5, SW6, SW7, SW8 and SW9, arranged in a diamond configuration to depict
“directional” headings North, South, East, West and Center respectively
•
SW10 CPU Reset pushbutton
The six pushbuttons all have the same active-High topology as the sample shown in
Figure 1-19. The five directional pushbuttons are assigned as GPIO and the sixth is assigned
as CPU_RESET. Figure 1-19 and Table 1-22, page 50 describe the pushbutton switches.
X-Ref Target - Figure 1-19
VCC1V5
Pushbutton
2
P4
P2
P3
4
3
4.7K
R401
2
CPU RESET
P1
1
1
5%
1/16W
sw10
UG534_19_072109
Figure 1-19:
ML605 Hardware User Guide
UG534 (v1.2.1) January 21, 2010
User Pushbutton Switch (Typical)
www.xilinx.com
49
Chapter 1: ML605 Evaluation Board
Table 1-22:
User Pushbutton Switch Connections
Pushbutton
Switch Pin
U1 FPGA Pin
Schematic Net Name
A19
GPIO_SW_N
SW5.2
A18
GPIO_SW_S
SW6.2
G17
GPIO_SW_E
SW7.2
H17
GPIO_SW_W
SW8.2
G26
GPIO_SW_C
SW9.2
H10
CPU_RESET
SW10.2
User DIP Switch
The ML605 includes an active-High eight pole DIP switch as described in Figure 1-20 and
Table 1-23.
X-Ref Target - Figure 1-20
VCC1V5
SW1
16
15
14
13
12
11
10
9
1
2
3
4
5
6
7
8
5%
SDMX-8-X
4.7K
2
4.7K
5%
1 RP7
3
4.7K
5%
1 RP7
4
4.7K
5%
5
1 RP7
10
5%
5%
9
5%
RP7
6
4.7K
RP7
6
4.7K
RP7
6
4.7K
RP7
6
4.7K
1 RP7
5%
7
8
GPIO DIP SW1
GPIO DIP SW2
GPIO DIP SW3
GPIO DIP SW4
GPIO DIP SW5
GPIO DIP SW6
GPIO DIP SW7
GPIO DIP SW8
UG534_20_072109
Figure 1-20:
Table 1-23:
50
User 8-pole DIP Switch
User DIP Switch Connections
U1 FPGA Pin
Schematic Net Name
DIP Switch Pin
D22
GPIO_DIP_SW1
SW1.1
C22
GPIO_DIP_SW2
SW1.2
L21
GPIO_DIP_SW3
SW1.3
L20
GPIO_DIP_SW4
SW1.4
C18
GPIO_DIP_SW5
SW1.5
B18
GPIO_DIP_SW6
SW1.6
K22
GPIO_DIP_SW7
SW1.7
K21
GPIO_DIP_SW8
SW1.8
www.xilinx.com
ML605 Hardware User Guide
UG534 (v1.2.1) January 21, 2010
Detailed Description
User SMA GPIO
The ML605 includes an pair of SMA connectors for GPIO as described in Figure 1-21 and
Table 1-24.
X-Ref Target - Figure 1-21
J56 32K10K-400E3
2
GND1
3
GND2
4
GND3
1
5
SIG GND4
6
GND5
7
GND6
8
GND7
USER SMA GPIO N
USER SMA GPIO P
J76 32K10K-400E3
2
GND1
3
GND2
4
GND3
1
5
SIG GND4
6
GND5
7
GND6
8
GND7
UG534_21_072109
Figure 1-21: User SMA GPIO
Table 1-24:
User SMA Connections
U1 FPGA Pin
Schematic Net Name
SMA Pin
W34
USER_SMA_GPIO_N
J56.1
V34
USER_SMA_GPIO_P
J57.1
ML605 Hardware User Guide
UG534 (v1.2.1) January 21, 2010
www.xilinx.com
51
Chapter 1: ML605 Evaluation Board
LCD Display (16 Character x 2 Lines)
The ML605 board has a 16-character x 2-line LCD (Display Tech S162D BA BC, installed
onto J41 2x7 header) on the board to display text information. Potentiometer R270 adjusts
the contrast of the LCD. A ST2378E (U33) 2.5V-to-5V level-shifter is used to shift the
voltage level between the FPGA and the LCD. The data interface to the LCD is connected
to the FPGA to support 4-bit mode only. The LCD module has a connector that allows the
LCD to be removed from the board to access to the components below it.
Caution! Care should be taken not to scratch or damage the surface of the LCD window.
X-Ref Target - Figure 1-22
VCC5
VCC5
NC
NC
LCD_E
LCD_RS
LCD_DB6
LCD_DB4
NC
NC
LCD_RW
LCD_VEE
2
4
6
8
10
12
14
1
1
3
5
7
9
11
13
32
32
6.81K
1%
1
LCD_DB7
LCD_DB5
2
R158
J41
R270
0-2K
1/2W
20%
32
2
3
SSW-107-01-T-D
silkscreen:
“LCD Contrast”
UG534_22_073109
Figure 1-22:
Table 1-25:
52
LCD Header J41 and Contrast Trimpot R270
LCD Header Connections
U1 FPGA Pin
Schematic Net Name
J41 Pin
AD14
LCD_DB4_LS
4
AK11
LCD_DB5_LS
3
AJ11
LCD_DB6_LS
2
AE12
LCD_DB7_LS
1
AC14
LCD_RW_LS
10
T28
LCD_RS_LS
11
AK12
LCD_E_LS
9
www.xilinx.com
ML605 Hardware User Guide
UG534 (v1.2.1) January 21, 2010
Detailed Description
18. Switches
The ML605 Evaluation board includes the following switches:
•
Power On/Off Slide Switch SW2
•
FPGA_PROG_B SW4 (active-Low)
•
SYSACE_RESET_B SW3 (active-Low)
•
System ACE CF CompactFlash Image Select DIP Switch S1 (active-High)
•
MODE, Boot EEPROM Select and CCLK Osc Enable DIP switch S2 (active-High)
Power On/Off Slide Switch SW2
SW2 is the ML605 board main power on/off switch. Sliding the switch actuator from the
off to on position applies 12V power from either J60 (6-pin Mini-Fit) or J25 (4-pin ATX)
power connector to the VCC12_P power plane via the 1mΩ 1% 3W series current sense
resistor R346. See “22. System Monitor,” page 68 for further details on 12V input current
sensing. Green LED DS25 will illuminate when the ML605 board power is on. See section
“21. Power Management,” page 65 for details on the onboard power system.
X-Ref Target - Figure 1-23
VCC12_P
J60
12v
12v
N/C
N/C
NC
2
3
4
2
5
4
NC
1
NC
2
3
+
C280
330UF
6
6
I2 I2
1
E1
E2
E1
E2
3W
0.001R
0.5%
Y14880R00100B09R
2
SW2
1201M2S3ABE2
CAUTION!
PCIe
DO NOT plug a PC ATX power supply 6-pin connector into
the J60 connector on the ML605 board. The ATX 6-pin
connector has a different pinout than J60 and will damage
the ML605 board and void the board warranty.
Power
ATX Peripheral Cable Connector
can plug into J25 when ML605 is
in PC and the desk top AC adapter
(brick) is not used.
J25
COM
COM
5V
1
39-30-1060
12V
R322
1.00K
1%
1/16W
DS25
16V
ELEC
5
I1 I1
NC
2
COM
R346
1
VCC12_P_IN
1
LED-GRN-SMT
COM
DPDT
1
DO NOT plug an auxilliary PCIe 6-pin molex power
connector into the J60 connector as this could damage the
PCIe motherboard and/or the ML605 board. J60 is marked
with a NO PCIE POWER label to warn users of the potential hazard.
2
3
4
NC
DO NOT apply power to J60 and the 4-pin ATX disk drive
connector J25 at the same time as this will damage the
ML605 board.
350211-1
UG534_23 _081209
Figure 1-23:
ML605 Hardware User Guide
UG534 (v1.2.1) January 21, 2010
Power On/Off Slide Switch SW2
www.xilinx.com
53
Chapter 1: ML605 Evaluation Board
FPGA_PROG_B Pushbutton SW4 (Active-Low)
This switch grounds the FPGA's PROG_B pin when pressed. This action clears the FPGA.
See the Virtex-6 FPGA Data Sheet for more information on clearing the contents of the
FPGA. [Ref 4]
X-Ref Target - Figure 1-24
RP4
1
4.7K
4
5%
VCC2V5
FPGA PROG
Pushbutton
FPGA_PROG_B
1
2
P1
P4
P2
P3
4
3
SW4
Silkscreen:
PROG
UG534_24_073109
Figure 1-24:
FPGA PROG_B Pushbutton SW4
SYSACE_RESET_B Pushbutton SW3 (Active-Low)
When the System ACE CF configuration mode pin is high (enabled by closing DIP switch
S1 switch 4), the System ACE CF controller configures the FPGA from the CompactFlash
card when a card is inserted or the SYSACE RESET button is pressed. See “5. System ACE
CF and CompactFlash Connector,” page 24 for more details.
X-Ref Target - Figure 1-25
silkscreen:
“SYSACE RESET”
SYSACE_RESET_B
Pushbutton
1
2
P1
P4
P2
P3
4
3
SW3
UG534_25_073109
Figure 1-25: System ACE CF RESET_B Pushbutton SW3
54
www.xilinx.com
ML605 Hardware User Guide
UG534 (v1.2.1) January 21, 2010
Detailed Description
System ACE CF CompactFlash Image Select DIP Switch S1
System ACE CF CompactFlash (CF) image select DIP switch S1, switches 1–3, select which
CF resident bitstream image is downloaded to the FPGA (Figure 1-26). S1 switches 1–3
offer eight binary addresses. When ON (High), the S1 switch 4 enables the System ACE CF
controller to configure the FPGA from the CF card when a card is inserted or when the
SYSACE RESET button is pressed. See “5. System ACE CF and CompactFlash Connector,”
page 24 for more details about the System ACE controller.
X-Ref Target - Figure 1-26
1
SYSACE_CFGMODEPIN
SYSACE_CFGADDR2
SYSACE_CFGADDR1
SYSACE_CFGADDR0
1
1%
1/16W
1
1%
1.00K
1/16W
1
2
R58
R61
1
2
2
1%
1.00K
1/16W
1.00K
2
R59
SDMX-4-X
1%
1.00K
1/16W
5%
R55
4
3
2
1
R60
1 2 3 4
5%
R64
S1
5
6
7
8
ON
5%
5%
R62
2
R63
2
2
510
510
1/16W
1/16W
1
510
1/16W
1
510
1/16W
VCC2V5
UG534_26_110409
Figure 1-26:
System ACE CF CompactFlash Image Select DIP Switch S1
Note: S1 switch 4 is the System ACE controller enable switch. When ON, this switch allows the
System ACE to boot at power-on if it finds a CF card present. In order to boot from BPI Flash U4 or
Xilinx Platform Flash (U27) without System ACE contention, S1 switch 4 must be OFF.
ML605 Hardware User Guide
UG534 (v1.2.1) January 21, 2010
www.xilinx.com
55
Chapter 1: ML605 Evaluation Board
Mode, Osc Enable, Boot EEPROM Select, and Addr Select DIP Switch S2
DIP switch S2 is a multi-purpose selector switch (Figure 1-27 and Table 1-27, page 57).
FPGA Mode: S2 switches 3, 4, and 5 control the FPGA mode (Table 1-26).
Oscillator Enable: S2 switch 1, CCLK_EXTERNAL, controls the enable pin of the 47 MHz
oscillator SiT8102 (X4). When switch 1 is closed (CCLK_EXTERNAL High), X4 drives a
47 MHz clock onto the FPGA_CCLK signal.
Boot EEPROM Select: S2 switch 2 is used to select the between the Xilinx Platform Flash or
the Numonyx Linear BPI Flash for the FPGA boot memory device.
Upper or Lower Address Select: S2 switch 6 is used to select the upper or lower half of
flash memory U4 as the source of the FPGA bitstream image. When FLASH_A23 is High,
the upper half of the address is selected. When FLASH_A23 is Low, the lower half of the
address is selected.
X-Ref Target - Figure 1-27
S2
R43
2
2
2
5%
1/16w
4.7K
2
5%
2
5%
2
1/16w
1
5%
1
1/16w
1
1/16w
1
5%
1
1/16w
1
1/16w
4.7K
R50
R53
4.7K
R54
4.7K
R55
4.7K
SDMX-6-X
4.7K
R56
FLASH_A23
FPGA_M2
FPGA_M1
FPGA_M0
P30_CS_SEL
CCLK EXTERNAL
5%
5 6
6
5
4
3
2
1
1 2 3 4
7
8
9
10
11
12
ON
R57
5%
2
5%
R52
5%
R51
1/16W
510
1
2
2
5%
1/16W
1/16W
1
510
1
510
1/16W
VCC2V5
UG534_27_110409
Figure 1-27:
Multi-Purpose Select DIP Switch S2
Table 1-26 shows the FPGA configuration modes controlled by S2 switches 3, 4, and 5.
Table 1-26:
ML605 Configuration Modes
Configuration Mode
56
M[2:0]
Bus Width
CCLK
Master BPI-Up
010
8, 16
Output
JTAG
101
1
Input (TCK)
Slave SelectMAP
110
8, 16, 32
Input
www.xilinx.com
ML605 Hardware User Guide
UG534 (v1.2.1) January 21, 2010
Detailed Description
Table 1-27:
Switch S2 Configuration Details
Switch
Configuration Mode/Method
Switch
Net Name
JTAG
System ACE CF
Slave SelectMAP
Platform Flash XL
Master BPI
P30 Linear Flash
S2.1
CCLK_EXTERNAL
Off
On
Off
S2.2
P30_CS_SEL
On(1)
Off
On
S2.3
FPGA_M0
On
Off
Off
S2.4
FPGA_M1
Off
On
On
S2.5
FPGA_M2
On
On
Off
S2.6
FLASH_A23
Off
Don't Care
Off(2)
Notes:
1. In JTAG mode, S2.2 is shown as ON for FPGA access to the P30 Linear Flash. Alternatively, set S2.2 to
OFF for FPGA access to the Platform Flash XL.
2. In Master BPI mode, S2.6 is shown as OFF for selecting initial configuration from BPI address
0x000000. Alternatively, set S2.6 to ON to select initial configuration from BPI address 0x800000.
See “3. 128 Mb Platform Flash XL,” page 20 and “4. 32 MB Linear BPI Flash,” page 20 for
details.
19. VITA 57.1 FMC HPC Connector
The ML605 implements both the High Pin Count (HPC, J64) and Low Pin Count (LPC, J63)
connector options of VITA 57.1.1 FMC specification. This section discusses the FMC HPC
J64 connector.
The FMC standard calls for two connector densities: a High Pin Count (HPC) and a Low
Pin Count (LPC) implementation. A common 10 x 40 position (400 pin locations) connector
form factor is used for both versions. The HPC version is fully populated with 400 pins
present, and the LPC version is partially populated with 160 pins.
The 10 x 40 rows of a FMC HPC connector provides connectivity for:
•
160 single-ended or 80 differential user-defined signals
•
10 MGTs
•
2 MGT clocks
•
4 differential clocks
•
159 ground, 15 power connections
Of the above signal and clock connectivity capability, the ML605 implements the following
subset:
•
78 differential user defined pairs:
♦
34 LA pairs
♦
24 HA pairs
♦
20 HB pairs
•
8 MGTs
•
2 MGT clocks
•
4 differential clocks
ML605 Hardware User Guide
UG534 (v1.2.1) January 21, 2010
www.xilinx.com
57
Chapter 1: ML605 Evaluation Board
Note: The ML605 board VADJ voltage for the FMC HPC and LPC connectors (J64 and J63) is fixed
at 2.5V (non-adjustable). The 2.5V rail cannot be turned off. The ML605 VITA 57.1 FMC interfaces
are compatible with 2.5V mezzanine cards capable of supporting 2.5V VADJ.
Table 1-28 shows the VITA 57.1 FMC HPC connections. The connector pinout is in
Appendix B, “VITA 57.1 FMC LPC (J63) and HPC (J64) Connector Pinout.”
Any signal named FMC_HPC_xxxx that is wired between a U1 FPGA pin and some other
device does not appear in this table.
Table 1-28:
J64 FMC
HPC Pin
58
VITA 57.1 FMC HPC Connections
Schematic Net Name
U1 FPGA
Pin
J64 FMC
HPC Pin
Schematic Net Name
U1 FPGA
Pin
A2
FMC_HPC_DP1_M2C_P
AE3
B12
FMC_HPC_DP7_M2C_P
AP5
A3
FMC_HPC_DP1_M2C_N
AE4
B13
FMC_HPC_DP7_M2C_N
AP6
A6
FMC_HPC_DP2_M2C_P
AF5
B16
FMC_HPC_DP6_M2C_P
AM5
A7
FMC_HPC_DP2_M2C_N
AF6
B17
FMC_HPC_DP6_M2C_N
AM6
A10
FMC_HPC_DP3_M2C_P
AG3
B20
FMC_HPC_GBTCLK1_M2C_P
AK6
A11
FMC_HPC_DP3_M2C_N
AG4
B21
FMC_HPC_GBTCLK1_M2C_N
AK5
A14
FMC_HPC_DP4_M2C_P
AJ3
B32
FMC_HPC_DP7_C2M_P
AP1
A15
FMC_HPC_DP4_M2C_N
AJ4
B33
FMC_HPC_DP7_C2M_N
AP2
A18
FMC_HPC_DP5_M2C_P
AL3
B36
FMC_HPC_DP6_C2M_P
AN3
A19
FMC_HPC_DP5_M2C_N
AL4
B37
FMC_HPC_DP6_C2M_N
AN4
A22
FMC_HPC_DP1_C2M_P
AD1
A23
FMC_HPC_DP1_C2M_N
AD2
A26
FMC_HPC_DP2_C2M_P
AF1
A27
FMC_HPC_DP2_C2M_N
AF2
A30
FMC_HPC_DP3_C2M_P
AH1
A31
FMC_HPC_DP3_C2M_N
AH2
A34
FMC_HPC_DP4_C2M_P
AK1
A35
FMC_HPC_DP4_C2M_N
AK2
A38
FMC_HPC_DP5_C2M_P
AM1
A39
FMC_HPC_DP5_C2M_N
AM2
C2
FMC_HPC_DP0_C2M_P
AB1
D4
FMC_HPC_GBTCLK0_M2C_P
AD6
C3
FMC_HPC_DP0_C2M_N
AB2
D5
FMC_HPC_GBTCLK0_M2C_N
AD5
C6
FMC_HPC_DP0_M2C_P
AC3
D8
FMC_HPC_LA01_CC_P
AK19
C7
FMC_HPC_DP0_M2C_N
AC4
D9
FMC_HPC_LA01_CC_N
AL19
C10
FMC_HPC_LA06_P
AG20
D11
FMC_HPC_LA05_P
AG22
C11
FMC_HPC_LA06_N
AG21
D12
FMC_HPC_LA05_N
AH22
www.xilinx.com
ML605 Hardware User Guide
UG534 (v1.2.1) January 21, 2010
Detailed Description
Table 1-28:
J64 FMC
HPC Pin
VITA 57.1 FMC HPC Connections (Cont’d)
Schematic Net Name
U1 FPGA
Pin
J64 FMC
HPC Pin
Schematic Net Name
U1 FPGA
Pin
C14
FMC_HPC_LA10_P
AM20
D14
FMC_HPC_LA09_P
AM18
C15
FMC_HPC_LA10_N
AL20
D15
FMC_HPC_LA09_N
AL18
C18
FMC_HPC_LA14_P
AN19
D17
FMC_HPC_LA13_P
AP19
C19
FMC_HPC_LA14_N
AN20
D18
FMC_HPC_LA13_N
AN18
C22
FMC_HPC_LA18_CC_P
AH25
D20
FMC_HPC_LA17_CC_P
AN27
C23
FMC_HPC_LA18_CC_N
AJ25
D21
FMC_HPC_LA17_CC_N
AM27
C26
FMC_HPC_LA27_P
AP30
D23
FMC_HPC_LA23_P
AL26
C27
FMC_HPC_LA27_N
AP31
D24
FMC_HPC_LA23_N
AM26
C30
IIC_SCL_MAIN_LS(1)
AK9
D26
FMC_HPC_LA26_P
AM25
C31
IIC_SDA_MAIN_LS(1)
AE9
D27
FMC_HPC_LA26_N
AL25
D29
FMC_HPC_TCK_BUF(2)
D30
FMC_TDI_BUF(2)
J17.1
D31
FMC_HPC_TDO(2)
J17.3
D33
FMC_TMS_BUF(2)
U88.17
U88.15
E2
FMC_HPC_HA01_CC_P
AD29
F1
FMC_HPC_PG_M2C_LS(1)
E3
FMC_HPC_HA01_CC_N
AC29
F4
FMC_HPC_HA00_CC_P
AE33
E6
FMC_HPC_HA05_P
AB27
F5
FMC_HPC_HA00_CC_N
AF33
E7
FMC_HPC_HA05_N
AC27
F7
FMC_HPC_HA04_P
AB28
E9
FMC_HPC_HA09_P
AB30
F8
FMC_HPC_HA04_N
AC28
E10
FMC_HPC_HA09_N
AB31
F10
FMC_HPC_HA08_P
AG31
E12
FMC_HPC_HA13_P
AE31
F11
FMC_HPC_HA08_N
AF31
E13
FMC_HPC_HA13_N
AD31
F13
FMC_HPC_HA12_P
AD32
E15
FMC_HPC_HA16_P
AC33
F14
FMC_HPC_HA12_N
AE32
E16
FMC_HPC_HA16_N
AB33
F16
FMC_HPC_HA15_P
AB32
E18
FMC_HPC_HA20_P
V32
F17
FMC_HPC_HA15_N
AC32
E19
FMC_HPC_HA20_N
V33
F19
FMC_HPC_HA19_P
U33
E21
FMC_HPC_HB03_P
AL30
F20
FMC_HPC_HA19_N
U32
E22
FMC_HPC_HB03_N
AM31
F22
FMC_HPC_HB02_P
AP32
E24
FMC_HPC_HB05_P
AN33
F23
FMC_HPC_HB02_N
AP33
E25
FMC_HPC_HB05_N
AN34
F25
FMC_HPC_HB04_P
AM33
E27
FMC_HPC_HB09_P
AL34
F26
FMC_HPC_HB04_N
AL33
ML605 Hardware User Guide
UG534 (v1.2.1) January 21, 2010
www.xilinx.com
J27
59
Chapter 1: ML605 Evaluation Board
Table 1-28:
J64 FMC
HPC Pin
60
VITA 57.1 FMC HPC Connections (Cont’d)
Schematic Net Name
U1 FPGA
Pin
J64 FMC
HPC Pin
Schematic Net Name
U1 FPGA
Pin
E28
FMC_HPC_HB09_N
AK34
F28
FMC_HPC_HB08_P
AK33
E30
FMC_HPC_HB13_P
AH33
F29
FMC_HPC_HB08_N
AK32
E31
FMC_HPC_HB13_N
AH32
F31
FMC_HPC_HB12_P
AJ31
E33
FMC_HPC_HB19_P
AL31
F32
FMC_HPC_HB12_N
AJ32
E34
FMC_HPC_HB19_N
AK31
F34
FMC_HPC_HB16_P
AH29
F35
FMC_HPC_HB16_N
AH30
AP25
G2
FMC_HPC_CLK1_M2C_P
AP20
H2
FMC_HPC_PRSNT_M2C_L(1)
G3
FMC_HPC_CLK1_M2C_N
AP21
H4
FMC_HPC_CLK0_M2C_P
K24
G6
FMC_HPC_LA00_CC_P
AF20
H5
FMC_HPC_CLK0_M2C_N
K23
G7
FMC_HPC_LA00_CC_N
AF21
H7
FMC_HPC_LA02_P
AC20
G9
FMC_HPC_LA03_P
AC19
H8
FMC_HPC_LA02_N
AD20
G10
FMC_HPC_LA03_N
AD19
H10
FMC_HPC_LA04_P
AF19
G12
FMC_HPC_LA08_P
AK22
H11
FMC_HPC_LA04_N
AE19
G13
FMC_HPC_LA08_N
AJ22
H13
FMC_HPC_LA07_P
AK21
G15
FMC_HPC_LA12_P
AM21
H14
FMC_HPC_LA07_N
AJ21
G16
FMC_HPC_LA12_N
AL21
H16
FMC_HPC_LA11_P
AM22
G18
FMC_HPC_LA16_P
AP22
H17
FMC_HPC_LA11_N
AN22
G19
FMC_HPC_LA16_N
AN23
H19
FMC_HPC_LA15_P
AM23
G21
FMC_HPC_LA20_P
AK23
H20
FMC_HPC_LA15_N
AL23
G22
FMC_HPC_LA20_N
AL24
H22
FMC_HPC_LA19_P
AN25
G24
FMC_HPC_LA22_P
AP27
H23
FMC_HPC_LA19_N
AN24
G25
FMC_HPC_LA22_N
AP26
H25
FMC_HPC_LA21_P
AN29
G27
FMC_HPC_LA25_P
AN28
H26
FMC_HPC_LA21_N
AP29
G28
FMC_HPC_LA25_N
AM28
H28
FMC_HPC_LA24_P
AN30
G30
FMC_HPC_LA29_P
AL28
H29
FMC_HPC_LA24_N
AM30
G31
FMC_HPC_LA29_N
AK28
H31
FMC_HPC_LA28_P
AK27
G33
FMC_HPC_LA31_P
AL29
H32
FMC_HPC_LA28_N
AJ27
G34
FMC_HPC_LA31_N
AK29
H34
FMC_HPC_LA30_P
AJ24
G36
FMC_HPC_LA33_P
AH23
H35
FMC_HPC_LA30_N
AK24
G37
FMC_HPC_LA33_N
AH24
H37
FMC_HPC_LA32_P
AG25
H38
FMC_HPC_LA32_N
AG26
www.xilinx.com
ML605 Hardware User Guide
UG534 (v1.2.1) January 21, 2010
Detailed Description
Table 1-28:
J64 FMC
HPC Pin
VITA 57.1 FMC HPC Connections (Cont’d)
Schematic Net Name
U1 FPGA
Pin
J64 FMC
HPC Pin
Schematic Net Name
U1 FPGA
Pin
J2
FMC_HPC_CLK3_M2C_P(2)
U84.6
K4
FMC_HPC_CLK2_M2C_P(2)
U83.6
J3
FMC_HPC_CLK3_M2C_N(2)
U84.7
K5
FMC_HPC_CLK2_M2C_N(2)
U83.7
J6
FMC_HPC_HA03_P
AA25
K7
FMC_HPC_HA02_P
AB25
J7
FMC_HPC_HA03_N
Y26
K8
FMC_HPC_HA02_N
AC25
J9
FMC_HPC_HA07_P
AA26
K10
FMC_HPC_HA06_P
AA28
J10
FMC_HPC_HA07_N
AB26
K11
FMC_HPC_HA06_N
AA29
J12
FMC_HPC_HA11_P
AG33
K13
FMC_HPC_HA10_P
AD34
J13
FMC_HPC_HA11_N
AG32
K14
FMC_HPC_HA10_N
AC34
J15
FMC_HPC_HA14_P
AA30
K16
FMC_HPC_HA17_CC_P
V30
J16
FMC_HPC_HA14_N
AA31
K17
FMC_HPC_HA17_CC_N
W30
J18
FMC_HPC_HA18_P
T33
K19
FMC_HPC_HA21_P
U31
J19
FMC_HPC_HA18_N
T34
K20
FMC_HPC_HA21_N
U30
J21
FMC_HPC_HA22_P
U28
K22
FMC_HPC_HA23_P
U26
J22
FMC_HPC_HA22_N
V29
K23
FMC_HPC_HA23_N
U27
J24
FMC_HPC_HB01_P
AN32
K25
FMC_HPC_HB00_CC_P
AF30
J25
FMC_HPC_HB01_N
AM32
K26
FMC_HPC_HB00_CC_N
AG30
J27
FMC_HPC_HB07_P
AJ34
K28
FMC_HPC_HB06_CC_P
AF26
J28
FMC_HPC_HB07_N
AH34
K29
FMC_HPC_HB06_CC_N
AE26
J30
FMC_HPC_HB11_P
AJ29
K31
FMC_HPC_HB10_P
AF28
J31
FMC_HPC_HB11_N
AJ30
K32
FMC_HPC_HB10_N
AF29
J33
FMC_HPC_HB15_P
AE28
K34
FMC_HPC_HB14_P
AE27
J34
FMC_HPC_HB15_N
AE29
K35
FMC_HPC_HB14_N
AD27
J36
FMC_HPC_HB18_P
AD25
K37
FMC_HPC_HB17_CC_P
AG27
J37
FMC_HPC_HB18_N
AD26
K38
FMC_HPC_HB17_CC_N
AG28
Notes:
1. Signals ending with _LS are not directly connected to the FMC HPC connector. _LS signals are connected between the listed U1
FPGA pin and a level shifter device. The signal connected between the shifted side of said device and the FMC HPC pin listed has
the same signal name, without the _LS on the end.
2. These signals do not connect to U1 FPGA pins. The pin numbers in the right-hand column identify the device and pin these signals
are connected to (U88.17 = U88 pin 17, and so on).
ML605 Hardware User Guide
UG534 (v1.2.1) January 21, 2010
www.xilinx.com
61
Chapter 1: ML605 Evaluation Board
Table 1-29:
Power Supply Voltages for HPC Connector
Voltage Supply
VADJ
62
Allowable
Voltage Range
No Pins Max Amps Tolerance
Max Capacitive
Load
Fixed 2.5V
4
4
+/- 5%
1000 uF
VIO_B_M2C
0-VADJ
2
1.15
+/- 5%
500 uF
VREF_A_M2C
0-VADJ
1
1 mA
+/- 2%
10 uF
VREF_B_M2C
0-VIO_B_M2C
1
1 mA
+/- 2%
10 uF
3P3VAUX
3.3V
1
20 mA
+/- 5%
150 uF
3P3V
3.3V
4
3
+/- 5%
1000 uF
12P0V
12V
2
1
+/- 5%
1000 uF
www.xilinx.com
ML605 Hardware User Guide
UG534 (v1.2.1) January 21, 2010
Detailed Description
20. VITA 57.1 FMC LPC Connector
The ML605 implements both the High Pin Count (HPC, J64) and Low Pin Count (LPC, J63)
connector options of VITA 57.1.1 FMC specification. This section discusses the FMC LPC
J63 connector.
The FMC standard calls for two connector densities: a High Pin Count (HPC) and a Low
Pin Count (LPC) implementation. A common 10 x 40 position (400 pin locations) connector
form factor is used for both versions. The HPC version is fully populated with 400 pins
present, and the LPC version is partially populated with 160 pins.
The 10 x 40 rows of a FMC LPC connector provides connectivity for:
•
68 single-ended or 34 differential user defined signals
•
1 MGT
•
1 MGT clock
•
2 differential clocks
•
61 ground, 10 power connections
Of the above signal and clock connectivity capability, the ML605 implements the full set:
•
34 differential user-defined pairs:
♦
34 LA pairs
•
1 MGT
•
1 MGT clock
•
2 differential clocks
Signaling Speed Ratings:
•
Single-ended: 9 GHz / 18 Gb/s
•
Differential
♦
Optimal Vertical: 9 GHz / 18 Gb/s
♦
Optimal Horizontal: 16 GHz / 32 Gb/s
♦
High Density Vertical 7 GHz / 15 Gb/s
Mechanical specifications:
•
Samtec SEAM/SEAF Series
•
1.27mm x 1.27mm (0.050" x 0.050") pitch
The Samtec connector system is rated for signaling speeds up to 9 GHz (18 Gb/s) based on
a -3 dB insertion loss point within a two-level signaling environment.
Note: The ML605 board VADJ voltage for the FMC HPC and LPC connectors (J64 and J63) is fixed
at 2.5V (non-adjustable). The 2.5V rail cannot be turned off. The ML605 VITA 57.1 FMC interfaces
are compatible with 2.5V mezzanine cards capable of supporting 2.5V VADJ.
ML605 Hardware User Guide
UG534 (v1.2.1) January 21, 2010
www.xilinx.com
63
Chapter 1: ML605 Evaluation Board
Table 1-30 shows the VITA 57.1 FMC LPC connections. The connector pinout is in
Appendix B, “VITA 57.1 FMC LPC (J63) and HPC (J64) Connector Pinout.”
Any signal named FMC_LPC_xxxx that is wired between a U1 FPGA pin and some other
device does not appear in this table..
Table 1-30:
J63 FMC
LPC Pin
64
VITA 57.1 FMC LPC Connections
Schematic Net Name
U1 FPGA
Pin
J63 FMC
LPC Pin
Schematic Net Name
U1 FPGA
Pin
C2
FMC_LPC_DP0_C2M_P
D1
D4
FMC_LPC_GBTCLK0_M2C_P
M6
C3
FMC_LPC_DP0_C2M_N
D2
D5
FMC_LPC_GBTCLK0_M2C_N
M5
C6
FMC_LPC_DP0_M2C_P
G3
D8
FMC_LPC_LA01_CC_P
F31
C7
FMC_LPC_DP0_M2C_N
G4
D9
FMC_LPC_LA01_CC_N
E31
C10
FMC_LPC_LA06_P
K33
D11
FMC_LPC_LA05_P
H34
C11
FMC_LPC_LA06_N
J34
D12
FMC_LPC_LA05_N
H33
C14
FMC_LPC_LA10_P
F30
D14
FMC_LPC_LA09_P
L25
C15
FMC_LPC_LA10_N
G30
D15
FMC_LPC_LA09_N
L26
C18
FMC_LPC_LA14_P
C33
D17
FMC_LPC_LA13_P
D34
C19
FMC_LPC_LA14_N
B34
D18
FMC_LPC_LA13_N
C34
C22
FMC_LPC_LA18_CC_P
L29
D20
FMC_LPC_LA17_CC_P
N28
C23
FMC_LPC_LA18_CC_N
L30
D21
FMC_LPC_LA17_CC_N
N29
C26
FMC_LPC_LA27_P
R31
D23
FMC_LPC_LA23_P
R28
C27
FMC_LPC_LA27_N
R32
D24
FMC_LPC_LA23_N
R27
D26
FMC_LPC_LA26_P
L33
D27
FMC_LPC_LA26_N
M32
G2
FMC_LPC_CLK1_M2C_P
F33
H2
FMC_LPC_PRSNT_M2C_L
AD9
G3
FMC_LPC_CLK1_M2C_N
G33
H4
FMC_LPC_CLK0_M2C_P
A10
G6
FMC_LPC_LA00_CC_P
K26
H5
FMC_LPC_CLK0_M2C_N
B10
G7
FMC_LPC_LA00_CC_N
K27
H7
FMC_LPC_LA02_P
G31
G9
FMC_LPC_LA03_P
J31
H8
FMC_LPC_LA02_N
H30
G10
FMC_LPC_LA03_N
J32
H10
FMC_LPC_LA04_P
K28
G12
FMC_LPC_LA08_P
J30
H11
FMC_LPC_LA04_N
J29
G13
FMC_LPC_LA08_N
K29
H13
FMC_LPC_LA07_P
G32
G15
FMC_LPC_LA12_P
E32
H14
FMC_LPC_LA07_N
H32
G16
FMC_LPC_LA12_N
E33
H16
FMC_LPC_LA11_P
D31
G18
FMC_LPC_LA16_P
A33
H17
FMC_LPC_LA11_N
D32
G19
FMC_LPC_LA16_N
B33
H19
FMC_LPC_LA15_P
C32
www.xilinx.com
ML605 Hardware User Guide
UG534 (v1.2.1) January 21, 2010
Detailed Description
Table 1-30:
J63 FMC
LPC Pin
VITA 57.1 FMC LPC Connections (Cont’d)
Schematic Net Name
U1 FPGA
Pin
J63 FMC
LPC Pin
Schematic Net Name
U1 FPGA
Pin
G21
FMC_LPC_LA20_P
P29
H20
FMC_LPC_LA15_N
B32
G22
FMC_LPC_LA20_N
R29
H22
FMC_LPC_LA19_P
M30
G24
FMC_LPC_LA22_P
N27
H23
FMC_LPC_LA19_N
N30
G25
FMC_LPC_LA22_N
P27
H25
FMC_LPC_LA21_P
R26
G27
FMC_LPC_LA25_P
P31
H26
FMC_LPC_LA21_N
T26
G28
FMC_LPC_LA25_N
P30
H28
FMC_LPC_LA24_P
N32
G30
FMC_LPC_LA29_P
N34
H29
FMC_LPC_LA24_N
P32
G31
FMC_LPC_LA29_N
P34
H31
FMC_LPC_LA28_P
N33
G33
FMC_LPC_LA31_P
M31
H32
FMC_LPC_LA28_N
M33
G34
FMC_LPC_LA31_N
L31
H34
FMC_LPC_LA30_P
M26
G36
FMC_LPC_LA33_P
K32
H35
FMC_LPC_LA30_N
M27
G37
FMC_LPC_LA33_N
K31
H37
FMC_LPC_LA32_P
N25
H38
FMC_LPC_LA32_N
M25
References
See the data sheet for the ROHS compliant FMC HPC Samtec SEARAY connector (carrier
side socket ASP-134486-01; module side plug ASP-134488-01), and the high-speed
characterization report for this connector system on the Samtec website. [Ref 32]
21. Power Management
AC Adapter and Input Power Jack/Switch
The ML605 is powered from a 12V source that is connected through a 6-pin (2X3) rightangle Mini-Fit type connector J60. The AC-to-DC power supply included in the kit has a
mating 6-pin plug.
When the ML605 is installed into a table top or tower PC's PCIe slot, the ML605 is typically
powered from the PC ATX power supply. One of the ATX hard disk type 4-pin power
connectors is plugged into ML605 connector J25. The ML605 can be powered with the AC
power adapter even when plugged into a PC PCIe motherboard slot; however, users are
cautioned not to also connect an ATX 4-pin power connector to J25. See the caution notes
below and in Figure 1-23, page 53.
Caution! DO NOT plug a PC ATX power supply 6-pin connector into ML605 connector J60.
The ATX 6-pin connector has a different pinout than ML605 J60, and connecting the ATX 6-pin
connector will damage the ML605 and void the board warranty.
Caution! DO NOT apply power to J60 and the 4-pin ATX disk drive connector J25 at the same
time as this will damage the ML605 board. Refer to Figure 1-23, page 53 for details.
The ML605 power can be turned on or off through the board mounted slide switch SW2.
When the switch is in the on position, a green LED (DS25) is illuminated.
ML605 Hardware User Guide
UG534 (v1.2.1) January 21, 2010
www.xilinx.com
65
Chapter 1: ML605 Evaluation Board
Onboard Power Regulation
Figure 1-28 shows the ML605 onboard power supply architecture. The ML605 uses power
solutions from Texas Instruments.
X-Ref Target - Figure 1-28
12V
PWR Jack
J25/J60
Power Supply
Linear Regulator TL1963
5.0V@1.5A max
U8
Power Controller 1
UCD9240PFC
VCC5
U24
Switching Module PTD08A020W
1.00V@20A max
U42
VCCINT
Switching Module PTD08A010W
2.50V@10A max
U91
VCCAUX
Switching Module PTD08A020W
2.5V@20A max
U43
VCC2V5, FPGA_VCC2V5
Linear Regulator TL1963A
1.8V@500mA max
U79
Power Controller 2
UCD9240PFC
VCC1V8
U25
Switching Regulator UCD7230RG
1.00V@6A max
U35
MGT_AVCC
Switching Regulator UCD7230RG
1.20V@6A max
U36
MGT_AVTT
Switching Module PTD08A010W
1.5V@10A max
U20
VCC1V5, FPGA_VCC1V5
Switching Module PTD08A010W
3.3V@10A max
U21
VCC3V3
Sink/Source DDR Regulator
Linear Regulator TPS51200
0.75V@3A max
U17
VTTDDR
UG534_28_012010
Figure 1-28:
66
ML605 Onboard Power Regulators
www.xilinx.com
ML605 Hardware User Guide
UG534 (v1.2.1) January 21, 2010
Detailed Description
Table 1-31:
Onboard Power System Devices
Device Type
Reference
Designator
Description
Power Rail
Net Name
Power Rail Schematic
Voltage
Page
UCD9240PFC
U24
PMBus Controller - Core (Addr = 52)
35
PTD08A020W
U42
20A 0.6V - 3.6V Adj. Switching Regulator
VCCINT_FPGA
1.00V
36
PTD08A020W
U43
20A 0.6V - 3.6V Adj. Switching Regulator
VCC2V5_FPGA
2.50V
37
PTD08A010W
U91
10A 0.6V - 3.6V Adj. Switching Regulator
VCCAUX
2.50V
38
UCD9240PFC
U25
PMBus Controller - Aux (Addr = 53)
UCD7230RGWR
U35
6A 0.6V - 3.6V Adj. Switching Regulator
MGT_AVCC
1.00V
41
UCD7230RGWR
U36
6A 0.6V - 3.6V Adj. Switching Regulator
MGT_AVTT
1.20V
42
PTD08A010W
U20
10A 0.6V - 3.6V Adj. Switching Regulator
VCC_1V5
1.50V
43
PTD08A010W
U21
10A 0.6V - 3.6V Adj. Switching Regulator
VCC_3V3
3.30V
44
TPS79518DCQR
U79
500mA Fixed Linear Regulator
VCC_1V8
1.80V
45
TPS512300DRCT
U17
3A DDR3 VTERM Tracking Linear
Regulator
VTTDDR
0.75V
45
TPS512300DRCT
U17
10mA Tracking Reference output
VTTVREF
0.75V
45
TL1963
U8
1.5A Fixed Linear Regulator
VCC5
5.00V
35
40
Voltage and current monitoring and control are available for selected power rails through
Texas Instruments’ Fusion Digital Power™ graphical user interface (GUI). Both onboard
TI power controllers are wired to the same PMBus. The PMBus connector, J3, is provided
for use with the TI USB Interface Adapter PMBus pod and associated TI GUI.
References
For more detailed information about this technology and the various power management
controllers and regulator modules offered by Texas Instruments, visit
http://www.ti.com/ww/en/analog/digital-power/index.html.
ML605 Hardware User Guide
UG534 (v1.2.1) January 21, 2010
www.xilinx.com
67
Chapter 1: ML605 Evaluation Board
22. System Monitor
The System Monitor provides information regarding the FPGA on-chip temperature and
power supply conditions via JTAG and an internal FPGA interface. The System Monitor
can also be used to monitor external analog signals via 17 external analog input channels.
For more information regarding this functionality, which is featured on every Virtex-6
family member, see http://www.xilinx.com/systemmonitor.
This section provides a brief overview of the System Monitor related functionality that is
supported on the ML605.
Reference and Power Supply
The System Monitor has dedicated analog power supply pins and supports the use of an
external 1.25V reference IC (U23) for the analog-to-digital conversion process. An option
(using jumper J19) to select an on-chip reference is also provided; however, the highest
accuracy over a temperature range of -40°C to +125°C is obtained using an external
reference. Figure 1-29 illustrates the power supply and reference options on the ML605.
For a more detailed discussion of these requirements, see the Virtex-6 FPGA System Monitor
User Guide. [Ref 15]
X-Ref Target - Figure 1-29
VCC2V5
Analog Supply Filter
1
2
SYSMON_AVDD
C78
X5R
10V
0.1UF
C190
X5R
6.3V
1UF
J19
3
VCC5
SYSMON_VREFP
2
AGND
U23
1
REF3012
REF3012AIDBZT
1
IN
2
OUT
C383
X5R
10V
0.1UF
1.25V
GND
Ferrie Bead
C191
X5R
6.3V
1UF
C79
X5R
10V
0.1UF
3
AGND
GND
AGND
Jumper on pins 1-2
Default Setting:
1-2 Select External Reference
2-3 Select On-Chip Reference
UG534_29_081209
Figure 1-29:
68
System Monitor External Reference
www.xilinx.com
ML605 Hardware User Guide
UG534 (v1.2.1) January 21, 2010
Detailed Description
System Monitor Header (J35)
Figure 1-30 shows the pinout for the System Monitor 12-pin header. The header provides
user access to the analog power supply (AVdd) and the 1.25V reference shown in
Figure 1-29, page 68. Access to the FPGA thermal diode and dedicated analog input
channel (Vp/Vn) is also provided on this header. The header can be used to connect user
specific analog signals and sensors to the system monitor.
The kelvin points for a 5 milliohm current sensing shunt in the FPGA 1V Vccint core supply
are also available on this header. By connecting header pins 9 to 11 and 10 to 12 using
jumpers, the system monitor can be used to monitor the FPGA core current and power
consumption. This can be used to collect useful power information about a particular
design or implementation.
X-Ref Target - Figure 1-30
NC
1
2
FPGA
Thermal Diode
access
FPGA_DX_P
NC
3
4
FPGA_DX_N
5
6
7
8
9
10
11
12
System Monitor
Header J35
1.25V Reference
Anti-alias Filter
SYSMON_VP
C169
X7R
16V
0.01UF
R233
100
1%
1/16W
SYSMON_VN
Vccint_shunt_P
R232
100
1%
1/16W
Vccint_shunt_N
SYSMON_AVDD
AGND
To Measure VCCINT Current:
Jumper on 9-11, 10-12
Dedicated Analog Inputs
Connect Vccint shunt to Vp,Vn
UG534_37 _081209
Figure 1-30:
ML605 Hardware User Guide
UG534 (v1.2.1) January 21, 2010
System Monitor Header (J35)
www.xilinx.com
69
Chapter 1: ML605 Evaluation Board
ML605 Board Power Monitor
In addition to monitoring the FPGA core supply power consumption, two auxiliary analog
input channels (of the 16 that are available) are used to implement a power monitor for the
entire ML605 board. The board power is monitored at the 12V power input connector.
Figure 1-31 shows how the power monitor is implemented and connected to the System
Monitor auxiliary input channels 12 and 13. A simple resistor divider is used to monitor
the 12V supply voltage and to provide a reference voltage to an instrumentation amplifier
(InAmp). The voltage on the auxiliary channel 12 is equal to supply voltage divided by 24
(~ 0.5V).
The InAmp is used to amplify (by a factor of 50) the voltage dropped across a 2 milliohm
current sense shunt. The voltage at the output of the InAmp is proportional to the current.
The voltage on auxiliary channel 13 = Current (amps) x 0.002 x 50. (e.g., 5A = 0.5V).
X-Ref Target - Figure 1-31
12V Supply Monitor
2mΩ ±1%
R1
R2
K1 K2
100nF
11.5kΩ ±0.5%
~0.5V
499Ω ±0.5%
IN+
IN-
V+
INA213
REF
SC70-6
Package
50V/V
OUT
~470Ω
10nF
1kΩ
10nF
VAUXP[13]
Current Channel
GND
1kΩ
10nF
~470Ω
VAUXN[13]
1kΩ
VAUXP[12]
10nF
1kΩ
Figure 1-31:
70
Voltage Channel
VAUXN[12]
UG534_38 _081209
ML605 12V Power Monitor
www.xilinx.com
ML605 Hardware User Guide
UG534 (v1.2.1) January 21, 2010
Detailed Description
Fan Controller
In highly demanding situations, active thermal management in the form of a heat sink and
fan may be required. In order to support this, drive circuitry for an external fan has been
provided on the ML605. A fan with tach output can be connect at header J59 as shown in
Figure 1-32. The fan PWM signal is generated by the FPGA and the tach input can be used
to close the control loop and regulate the fan speed. Alternatively, the FPGA temperature
as recorded by the System Monitor can be used to close the PWM control loop for the fan.
X-Ref Target - Figure 1-32
VCC12_P
R367
10.0K
1%
1/16W
GND
1
12V
2
SM_FAN_TACH
3
R358
4.75K
1%
2
D16
VCC2V5
1N4148
1
Tach
R368
10.0K
1%
1/16W
J59
R369
10.0K
1%
1/16W
2
Q24
SM_FAN_PWM
4
0
1
NDT3055L
3
UG534_39 _081209
Figure 1-32:
ML605 Hardware User Guide
UG534 (v1.2.1) January 21, 2010
www.xilinx.com
ML605 Fan Driver
71
Chapter 1: ML605 Evaluation Board
FPGA Power Supply Margining
The PMBus (IIC), which provides access to the 2 x UDC9240 power controllers, can also be
accessed via FPGA I/O in addition to a dedicated header (J3), see Figure 1-33. A full
description of the UDC9240 functionality is outside the scope of this user guide. However,
this useful feature can be used, for example, to margin the FPGA and board power
supplies when evaluating a design. The System Monitor provides accurate measurements
of the on-chip supply voltages as the FPGA supplies are margined. The PMBus (and fan)
connections are shown in Figure 1-33.
X-Ref Target - Figure 1-33
TI_V3P3
PMBus Connector
R301
100K
5%
J3
NC
NC
NC
1
3
5
7
9
R299
100K
5%
R300
100K
5%
UDC9240
NC
NC
2
4
6
8
10
PMBUS_ALERT
PMBUS_DATA
PMBUS_CLK
PMBUS_CTRL
35
20
19
36
DGND1
9240
R335
1.0M
5%
AGND1
BANK 34
6vlx240tff1156
IO_L11N_SRCC_34_AJ9
IO_L11P_SRCC_34_AH9
IO_L10N_MRCC_34_AB10
IO_L10P_MRCC_34_AC10
IO_L9N_MRCC_34_M10
IO_L9P_MRCC_34_L10
AJ9
AH9
AB10
AC10
M10
L10
PMBUS_CTRL_LS
PMBUS_ALERT_LS
PMBUS_DATA_LS
PMBUS_CLK_LS
SM_FAN_TACH
SM_FAN_PWM
UG534_35_081209
Figure 1-33: UDC9240 PMBus Access
System Monitor ML605 Demonstration Design
The various features described in this section are easily evaluated using a MicroBlaze™
based reference designed provided with the ML605 Evaluation Board. This reference
design supports a UART based interface using a terminal program such as Hyperterminal
to provide information on the FPGA power supplies, temperature, and power
consumption. In addition, the UART interface can be used to margin the FPGA supplies
over the PMBus.
The System Monitor functionality can also be accessed at any time via JTAG using the
ChipScope Pro Analyzer tool without design modifications or cores inserted into a user
design. The ChipScope Pro Analyzer tool automatically connects to the System Monitor
via a JTAG cable after a connection is established.
References
For more information on using the System Monitor and an overview of the tool support for
this feature, see the Virtex-6 FPGA System Monitor User Guide. [Ref 15]
72
www.xilinx.com
ML605 Hardware User Guide
UG534 (v1.2.1) January 21, 2010
Configuration Options
Configuration Options
The FPGA on the ML605 Evaluation Board can be configured by the following methods:
•
“3. 128 Mb Platform Flash XL,” page 20
•
“4. 32 MB Linear BPI Flash,” page 20
•
“5. System ACE CF and CompactFlash Connector”
•
“6. USB JTAG,” page 26
For more information, see the Virtex-6 FPGA Configuration User Guide at
http://www.xilinx.com/support/documentation/user_guides/ug360.pdf.
Table 1-32:
Mode Switch S2 Settings
Mode Pins (M2,M1,M0)
Configuration Mode
110
Slave SelectMAP
010
BPI Mode
101
JTAG
With the mode set to JTAG 101, the ML605 will not attempt to boot or load a bitstream
from either of the Flash devices. If a CompactFlash (CF) card is installed in the CF socket
U73, System ACE CF will attempt to load a bitstream from the CF card image address
pointed to by the image select switch S1. With no CF card present, the ML605 can be
configured via the onboard JTAG controller and USB download cable as described above.
With the mode set to either Slave SelectMAP 110, or BPI Mode 010, the FPGA will attempt
to configure itself from the selected Flash device as described in “3. 128 Mb Platform Flash
XL,” page 20.
Note: S1 switch 4 is the System ACE controller enable switch. When ON, this switch allows the
System ACE to boot at power-on if it finds a CF card present. In order to boot from BPI Flash U4 or
Xilinx Platform Flash (U27) without System ACE contention, S1 switch 4 must be OFF.
ML605 Hardware User Guide
UG534 (v1.2.1) January 21, 2010
www.xilinx.com
73
Chapter 1: ML605 Evaluation Board
74
www.xilinx.com
ML605 Hardware User Guide
UG534 (v1.2.1) January 21, 2010
Appendix A
Default Switch and Jumper Settings
Table A-1:
Default Switch Settings
REFDES
SW2
Function/Type
Board power slide-switch
Default
off
User GPIO 8-pole DIP switch
SW1
8
off
7
off
6
off
5
off
4
off
3
off
2
off
1
off
System ACE CF configuration and image select 4-pole DIP switch
S1
4
SysACE Mode = 1 (1)
off
3
SysAce CFGAddr 2 = 0
off
2
SysAce CFGAddr 1 = 0
off
1
SysAce CFGAddr 0 = 0
off
FPGA mode, boot PROM select and FPGA CCLK select 6-pole DIP
switch
S2
6
FLASH_A23 = 0
off
5
M2 = 0
off
4
M1 = 1
M[2:0] = 010 = Master BPI-Up
on
3
M0 = 0
off
2
CS_SEL = 1 = boot from BPI Flash
on
1
EXT_CCLK = 0
off
Notes:
1. S1 position 4 is the System ACE controller enable switch. When ON, this switch allows the System
ACE to boot at power on if it finds a CF card present. In order to boot from BPI Flash or Xilinx Platform
Flash without System ACE contention, S1 switch 4 must be OFF.
ML605 Hardware User Guide
UG534 (v1.2.1) January 21, 2010
www.xilinx.com
75
Appendix A: Default Switch and Jumper Settings
Table A-2:
Default Jumper Settings
Jumper REFDES
Function
Default
J69
System ACE CF Error LED Enable
Jump 1-2
J66
pins 1-2: GMII/MII to Cu
pins 2-3: SGMII to Cu, no clk
Jump 1 - 2
J67
pins 1-2: GMII/MII to Cu
pins 2-3: SGMII to Cu, no clk
Jump 1 - 2
J68
J66 pins 1-2, J68 ON: RGMII, modified MII in Cu
no jumper
J18
exclude FMC LPC connector
Jump 1 - 2
J17
exclude FMC LPC connector
Jump 1 - 2
J19
Test_mon_vrefp sourced by U23, REF3012
Jump 1 - 2
J35
measure voltage on R-kelvin on 12V rail
GMII:
FMC Bypass:
System Monitor:
Jump 9 - 11,
Jump 10 - 12
SFP Module:
J54
Full BW
Jump 1 - 2
J65
SFP Enable
Jump 1 - 2
1 lane
Jump 1 - 2
PCIe Lane Size:
J42
76
www.xilinx.com
ML605 Hardware User Guide
UG534 (v1.2.1) January 21, 2010
Appendix B
VITA 57.1 FMC LPC (J63) and HPC (J64)
Connector Pinout
Figure B-1 shows the pinout of the FMC LPC connector. Pins marked NC are not
connected.
X-Ref Target - Figure B-1
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
K
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
J
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
H
VR EF _A_M2C
PR SNT_M2C_L
GND
CLK0_M2C _P
CLK0_M2C _N
GND
LA02_P
LA02_N
GND
LA04_P
LA04_N
G ND
LA07_P
LA07_N
G ND
LA11_P
LA11_N
G ND
LA15_P
LA15_N
G ND
LA19_P
LA19_N
G ND
LA21_P
LA21_N
G ND
LA24_P
LA24_N
G ND
LA28_P
LA28_N
G ND
LA30_P
LA30_N
G ND
LA32_P
LA32_N
G ND
V ADJ
G
GND
C LK 1_M2C_P
C LK 1_M2C_N
GND
GND
LA00_P _C C
LA00_N_C C
GND
LA03_P
LA03_N
GND
LA08_P
LA08_N
GND
LA12_P
LA12_N
GND
LA16_P
LA16_N
GND
LA20_P
LA20_N
GND
LA22_P
LA22_N
GND
LA25_P
LA25_N
GND
LA29_P
LA29_N
GND
LA31_P
LA31_N
GND
LA33_P
LA33_N
GND
VADJ
G ND
Figure B-1:
ML605 Hardware User Guide
UG534 (v1.2.1) January 21, 2010
F
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
E
D
NC
P G_C2M
NC
G ND
NC
G ND
NC G BT CLK0_M2C _P
NC G BT CLK0_M2C _N
NC
G ND
NC
G ND
NC
LA01_P _C C
NC
LA01_N_C C
NC
GND
NC
LA05_P
NC
LA05_N
NC
GND
NC
LA09_P
NC
LA09_N
NC
GND
NC
LA13_P
NC
LA13_N
NC
GND
NC
LA17_P _C C
NC
LA17_N_C C
NC
GND
NC
LA23_P
NC
LA23_N
NC
GND
NC
LA26_P
NC
LA26_N
NC
GND
NC
T CK
NC
TDI
NC
TDO
NC
3P3VAUX
NC
TMS
NC
TR ST _L
NC
G A1
NC
3P 3V
NC
GND
NC
3P3V
NC
GND
NC
3P 3V
C
G ND
DP 0_C2M_P
DP 0_C2M_N
GND
GND
DP 0_M2C_P
DP 0_M2C_N
G ND
G ND
LA06_P
LA06_N
GND
G ND
LA10_P
LA10_N
G ND
GND
LA14_P
LA14_N
G ND
G ND
LA18_P _C C
LA18_N_C C
GND
G ND
LA27_P
LA27_N
G ND
GND
S CL
S DA
GND
G ND
GA0
12P0V
GND
12P0V
G ND
3P3V
GND
B
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
A
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
FMC LPC Connector Pinout
www.xilinx.com
77
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
K
VR EF _B _M2C
GND
GND
CLK2_M2C _P
CLK2_M2C _N
GND
HA02_P
HA02_N
GND
HA06_P
HA06_N
G ND
HA10_P
HA10_N
G ND
HA17_P _C C
HA17_N_C C
G ND
HA21_P
HA21_N
G ND
HA23_P
HA23_N
G ND
HB00_P _C C
HB00_N_C C
G ND
HB06_P _C C
HB06_N_C C
G ND
HB10_P
HB10_N
G ND
HB14_P
HB14_N
G ND
HB17_P _C C
HB17_N_C C
G ND
V IO_B _M2C
J
GND
C LK 3_M2C_P
C LK 3_M2C_N
GND
GND
HA03_P
HA03_N
GND
HA07_P
HA07_N
GND
HA11_P
HA11_N
GND
HA14_P
HA14_N
G ND
HA18_P
HA18_N
GND
HA22_P
HA22_N
GND
HB01_P
HB01_N
G ND
HB07_P
HB07_N
G ND
HB11_P
HB11_N
GND
HB15_P
HB15_N
GND
HB18_P
HB18_N
G ND
VIO_B_M2C
GND
H
V RE F_A_M2C
P RS NT _M2C _L
G ND
C LK 0_M2C_P
C LK 0_M2C_N
GND
LA02_P
LA02_N
GND
LA04_P
LA04_N
GND
LA07_P
LA07_N
GND
LA11_P
LA11_N
GND
LA15_P
LA15_N
GND
LA19_P
LA19_N
GND
LA21_P
LA21_N
GND
LA24_P
LA24_N
GND
LA28_P
LA28_N
GND
LA30_P
LA30_N
GND
LA32_P
LA32_N
G ND
V ADJ
G
G ND
CLK1_M2C _P
CLK1_M2C _N
G ND
G ND
LA00_P _C C
LA00_N_C C
GND
LA03_P
LA03_N
GND
LA08_P
LA08_N
GND
LA12_P
LA12_N
GND
LA16_P
LA16_N
GND
LA20_P
LA20_N
GND
LA22_P
LA22_N
GND
LA25_P
LA25_N
GND
LA29_P
LA29_N
GND
LA31_P
LA31_N
GND
LA33_P
LA33_N
GND
VADJ
G ND
F
PG _M2C
GND
GND
HA00_P _C C
HA00_N_C C
G ND
HA04_P
HA04_N
GND
HA08_P
HA08_N
GND
HA12_P
HA12_N
GND
HA15_P
HA15_N
GND
HA19_P
HA19_N
GND
HB02_P
HB02_N
GND
HB04_P
HB04_N
GND
HB08_P
HB08_N
GND
HB12_P
HB12_N
GND
HB16_P
HB16_N
GND
HB20_P
HB20_N
GND
VADJ
E
GND
HA01_P _C C
HA01_N_C C
G ND
G ND
HA05_P
HA05_N
GND
HA09_P
HA09_N
GND
HA13_P
HA13_N
GND
HA16_P
HA16_N
GND
HA20_P
HA20_N
GND
HB03_P
HB03_N
GND
HB05_P
HB05_N
GND
HB09_P
HB09_N
GND
HB13_P
HB13_N
GND
HB19_P
HB19_N
GND
HB21_P
HB21_N
GND
V ADJ
GND
D
P G_C2M
G ND
G ND
GB TC LK 0_M2C_P
GB TC LK 0_M2C_N
GND
GND
LA01_P _C C
LA01_N_C C
GND
LA05_P
LA05_N
GND
LA09_P
LA09_N
GND
LA13_P
LA13_N
GND
LA17_P _C C
LA17_N_C C
GND
LA23_P
LA23_N
GND
LA26_P
LA26_N
GND
T CK
TDI
TDO
3P3VAUX
TMS
TR ST _L
G A1
3P 3V
GND
3P3V
G ND
3P3V
C
G ND
DP 0_C2M_P
DP 0_C2M_N
G ND
G ND
DP0_M2C _P
DP0_M2C _N
G ND
G ND
LA06_P
LA06_N
GND
G ND
LA10_P
LA10_N
G ND
GND
LA14_P
LA14_N
G ND
G ND
LA18_P _C C
LA18_N_C C
GND
G ND
LA27_P
LA27_N
G ND
GND
S CL
S DA
GND
G ND
GA0
12P0V
GND
12P0V
G ND
3P 3V
G ND
B
RE S1
G ND
G ND
DP 9_M2C_P
DP 9_M2C_N
GND
GND
DP 8_M2C_P
DP 8_M2C_N
GND
GND
DP7_M2C _P
DP 7_M2C_N
GND
GND
DP 6_M2C_P
DP6_M2C _N
GND
GND
GB TC LK 1_M2C_P
GB TC LK 1_M2C_N
G ND
G ND
DP9_C 2M_P
DP 9_C2M_N
GND
GND
DP 8_C2M_P
DP8_C 2M_N
GND
GND
DP7_C 2M_P
DP 7_C2M_N
G ND
G ND
DP6_C 2M_P
DP6_C 2M_N
GND
GND
RE S0
A
GND
DP 1_M2C_P
DP 1_M2C_N
G ND
G ND
DP2_M2C _P
DP2_M2C _N
G ND
G ND
DP3_M2C _P
DP3_M2C _N
GND
G ND
DP4_M2C _P
DP4_M2C _N
G ND
GND
DP5_M2C _P
DP5_M2C _N
G ND
G ND
DP 1_C2M_P
DP 1_C2M_N
GND
G ND
DP2_C 2M_P
DP2_C 2M_N
G ND
GND
DP3_C 2M_P
DP3_C 2M_N
GND
G ND
DP 4_C2M_P
DP 4_C2M_N
GND
GND
DP5_C 2M_P
DP5_C 2M_N
GND
Appendix B: VITA 57.1 FMC LPC (J63) and HPC (J64) Connector Pinout
Figure B-2 shows the pinout of the FMC HPC connector.
X-Ref Target - Figure B-2
Figure B-2: FMC HPC Connector Pinout
78
www.xilinx.com
ML605 Hardware User Guide
UG534 (v1.2.1) January 21, 2010
Appendix C
ML605 Master UCF
The UCF template is provided for designs that target the ML605. Net names provided in
the constraints below correlate with net names on the ML605 Rev. D schematic. On
identifying the appropriate pins, the net names below should be replaced with net names
in the user RTL. See the Constraints Guide for more information.
Users can refer to the UCF files generated by tools such as MIG (Memory Interface
Generator for memory interfaces) and BSB (Base System Builder) for more detailed
information concerning the I/O standards required for each particular interface. The FMC
connectors J63 and J64 are connected to 2.5V Vcco banks. Because each user’s FMC card
implements customer-specific circuitry, the FMC bank I/O standards must be uniquely
defined by each customer.
NET
NET
##
NET
NET
NET
NET
NET
NET
NET
NET
NET
NET
NET
NET
NET
NET
NET
NET
NET
NET
NET
NET
NET
NET
NET
NET
NET
NET
NET
NET
NET
NET
NET
NET
NET
NET
"CLK_33MHZ_SYSACE"
"CPU_RESET"
LOC = "AE16";
LOC = "H10";
## 93
## 2
on U19
on SW10 pushbutton (active-High)
"DDR3_A0"
"DDR3_A1"
"DDR3_A2"
"DDR3_A3"
"DDR3_A4"
"DDR3_A5"
"DDR3_A6"
"DDR3_A7"
"DDR3_A8"
"DDR3_A9"
"DDR3_A10"
"DDR3_A11"
"DDR3_A12"
"DDR3_A13"
"DDR3_A14"
"DDR3_A15"
"DDR3_BA0"
"DDR3_BA1"
"DDR3_BA2"
"DDR3_CAS_B"
"DDR3_CKE0"
"DDR3_CKE1"
"DDR3_CLK0_N"
"DDR3_CLK0_P"
"DDR3_CLK1_N"
"DDR3_CLK1_P"
"DDR3_D0"
"DDR3_D1"
"DDR3_D2"
"DDR3_D3"
"DDR3_D4"
"DDR3_D5"
"DDR3_D6"
"DDR3_D7"
LOC
LOC
LOC
LOC
LOC
LOC
LOC
LOC
LOC
LOC
LOC
LOC
LOC
LOC
LOC
LOC
LOC
LOC
LOC
LOC
LOC
LOC
LOC
LOC
LOC
LOC
LOC
LOC
LOC
LOC
LOC
LOC
LOC
LOC
##
##
##
##
##
##
##
##
##
##
##
##
##
##
##
##
##
##
##
##
##
##
##
##
##
##
##
##
##
##
##
##
##
##
on
on
on
on
on
on
on
on
on
on
on
on
on
on
on
on
on
on
on
on
on
on
on
on
on
on
on
on
on
on
on
on
on
on
ML605 Hardware User Guide
UG534 (v1.2.1) January 21, 2010
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
"L14";
"A16";
"B16";
"E16";
"D16";
"J17";
"A15";
"B15";
"G15";
"F15";
"M16";
"M15";
"H15";
"J15";
"D15";
"C15";
"K19";
"J19";
"L15";
"C17";
"M18";
"M17";
"H18";
"G18";
"L16";
"K16";
"J11";
"E13";
"F13";
"K11";
"L11";
"K13";
"K12";
"D11";
98
97
96
95
92
91
90
86
89
85
107
84
83
119
80
78
109
108
79
115
73
74
103
101
104
102
5
7
15
17
4
6
16
18
www.xilinx.com
J1
J1
J1
J1
J1
J1
J1
J1
J1
J1
J1
J1
J1
J1
J1
J1
J1
J1
J1
J1
J1
J1
J1
J1
J1
J1
J1
J1
J1
J1
J1
J1
J1
J1
79
Appendix C: ML605 Master UCF
NET
NET
NET
NET
NET
NET
NET
NET
NET
NET
NET
NET
NET
NET
NET
NET
NET
NET
NET
NET
NET
NET
NET
NET
NET
NET
NET
NET
NET
NET
NET
NET
NET
NET
NET
NET
NET
NET
NET
NET
NET
NET
NET
NET
NET
NET
NET
NET
NET
NET
NET
NET
NET
NET
NET
NET
NET
NET
NET
NET
NET
NET
NET
NET
NET
80
"DDR3_D8"
"DDR3_D9"
"DDR3_D10"
"DDR3_D11"
"DDR3_D12"
"DDR3_D13"
"DDR3_D14"
"DDR3_D15"
"DDR3_D16"
"DDR3_D17"
"DDR3_D18"
"DDR3_D19"
"DDR3_D20"
"DDR3_D21"
"DDR3_D22"
"DDR3_D23"
"DDR3_D24"
"DDR3_D25"
"DDR3_D26"
"DDR3_D27"
"DDR3_D28"
"DDR3_D29"
"DDR3_D30"
"DDR3_D31"
"DDR3_D32"
"DDR3_D33"
"DDR3_D34"
"DDR3_D35"
"DDR3_D36"
"DDR3_D37"
"DDR3_D38"
"DDR3_D39"
"DDR3_D40"
"DDR3_D41"
"DDR3_D42"
"DDR3_D43"
"DDR3_D44"
"DDR3_D45"
"DDR3_D46"
"DDR3_D47"
"DDR3_D48"
"DDR3_D49"
"DDR3_D50"
"DDR3_D51"
"DDR3_D52"
"DDR3_D53"
"DDR3_D54"
"DDR3_D55"
"DDR3_D56"
"DDR3_D57"
"DDR3_D58"
"DDR3_D59"
"DDR3_D60"
"DDR3_D61"
"DDR3_D62"
"DDR3_D63"
"DDR3_DM0"
"DDR3_DM1"
"DDR3_DM2"
"DDR3_DM3"
"DDR3_DM4"
"DDR3_DM5"
"DDR3_DM6"
"DDR3_DM7"
"DDR3_DQS0_N"
LOC
LOC
LOC
LOC
LOC
LOC
LOC
LOC
LOC
LOC
LOC
LOC
LOC
LOC
LOC
LOC
LOC
LOC
LOC
LOC
LOC
LOC
LOC
LOC
LOC
LOC
LOC
LOC
LOC
LOC
LOC
LOC
LOC
LOC
LOC
LOC
LOC
LOC
LOC
LOC
LOC
LOC
LOC
LOC
LOC
LOC
LOC
LOC
LOC
LOC
LOC
LOC
LOC
LOC
LOC
LOC
LOC
LOC
LOC
LOC
LOC
LOC
LOC
LOC
LOC
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
"M13";
"J14";
"B13";
"B12";
"G10";
"M11";
"C12";
"A11";
"G11";
"F11";
"D14";
"C14";
"G12";
"G13";
"F14";
"H14";
"C19";
"G20";
"E19";
"F20";
"A20";
"A21";
"E22";
"E23";
"G21";
"B21";
"A23";
"A24";
"C20";
"D20";
"J20";
"G22";
"D26";
"F26";
"B26";
"E26";
"C24";
"D25";
"D27";
"C25";
"C27";
"B28";
"D29";
"B27";
"G27";
"A28";
"E24";
"G25";
"F28";
"B31";
"H29";
"H28";
"B30";
"A30";
"E29";
"F29";
"E11";
"B11";
"E14";
"D19";
"B22";
"A26";
"A29";
"A31";
"E12";
##
##
##
##
##
##
##
##
##
##
##
##
##
##
##
##
##
##
##
##
##
##
##
##
##
##
##
##
##
##
##
##
##
##
##
##
##
##
##
##
##
##
##
##
##
##
##
##
##
##
##
##
##
##
##
##
##
##
##
##
##
##
##
##
##
21
23
33
35
22
24
34
36
39
41
51
53
40
42
50
52
57
59
67
69
56
58
68
70
129
131
141
143
130
132
140
142
147
149
157
159
146
148
158
160
163
165
175
177
164
166
174
176
181
183
191
193
180
182
192
194
11
28
46
63
136
153
170
187
10
www.xilinx.com
on
on
on
on
on
on
on
on
on
on
on
on
on
on
on
on
on
on
on
on
on
on
on
on
on
on
on
on
on
on
on
on
on
on
on
on
on
on
on
on
on
on
on
on
on
on
on
on
on
on
on
on
on
on
on
on
on
on
on
on
on
on
on
on
on
J1
J1
J1
J1
J1
J1
J1
J1
J1
J1
J1
J1
J1
J1
J1
J1
J1
J1
J1
J1
J1
J1
J1
J1
J1
J1
J1
J1
J1
J1
J1
J1
J1
J1
J1
J1
J1
J1
J1
J1
J1
J1
J1
J1
J1
J1
J1
J1
J1
J1
J1
J1
J1
J1
J1
J1
J1
J1
J1
J1
J1
J1
J1
J1
J1
ML605 Hardware User Guide
UG534 (v1.2.1) January 21, 2010
NET
NET
NET
NET
NET
NET
NET
NET
NET
NET
NET
NET
NET
NET
NET
NET
NET
NET
NET
NET
NET
NET
NET
##
NET
NET
NET
NET
NET
NET
NET
NET
NET
NET
NET
NET
NET
NET
NET
NET
NET
NET
NET
##
NET
NET
NET
NET
NET
NET
NET
NET
NET
NET
NET
NET
NET
NET
NET
NET
NET
NET
NET
NET
NET
"DDR3_DQS0_P"
"DDR3_DQS1_N"
"DDR3_DQS1_P"
"DDR3_DQS2_N"
"DDR3_DQS2_P"
"DDR3_DQS3_N"
"DDR3_DQS3_P"
"DDR3_DQS4_N"
"DDR3_DQS4_P"
"DDR3_DQS5_N"
"DDR3_DQS5_P"
"DDR3_DQS6_N"
"DDR3_DQS6_P"
"DDR3_DQS7_N"
"DDR3_DQS7_P"
"DDR3_ODT0"
"DDR3_ODT1"
"DDR3_RAS_B"
"DDR3_RESET_B"
"DDR3_S0_B"
"DDR3_S1_B"
"DDR3_TEMP_EVENT"
"DDR3_WE_B"
LOC
LOC
LOC
LOC
LOC
LOC
LOC
LOC
LOC
LOC
LOC
LOC
LOC
LOC
LOC
LOC
LOC
LOC
LOC
LOC
LOC
LOC
LOC
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
"D12";
"J12";
"H12";
"A14";
"A13";
"H20";
"H19";
"C23";
"B23";
"A25";
"B25";
"G28";
"H27";
"D30";
"C30";
"F18";
"E17";
"L19";
"E18";
"K18";
"K17";
"D17";
"B17";
##
##
##
##
##
##
##
##
##
##
##
##
##
##
##
##
##
##
##
##
##
##
##
12
27
29
45
47
62
64
135
137
152
154
169
171
186
188
116
120
110
30
114
121
198
113
"DVI_D0"
"DVI_D1"
"DVI_D2"
"DVI_D3"
"DVI_D4"
"DVI_D5"
"DVI_D6"
"DVI_D7"
"DVI_D8"
"DVI_D9"
"DVI_D10"
"DVI_D11"
"DVI_DE"
"DVI_GPIO1_FMC_C2M_PG_LS"
"DVI_H"
"DVI_RESET_B_LS"
"DVI_V"
"DVI_XCLK_N"
"DVI_XCLK_P"
LOC
LOC
LOC
LOC
LOC
LOC
LOC
LOC
LOC
LOC
LOC
LOC
LOC
LOC
LOC
LOC
LOC
LOC
LOC
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
"AJ19";
"AH19";
"AM17";
"AM16";
"AD17";
"AE17";
"AK18";
"AK17";
"AE18";
"AF18";
"AL16";
"AK16";
"AD16";
"K9";
"AN17";
"AP17";
"AD15";
"AC17";
"AC18";
##
##
##
##
##
##
##
##
##
##
##
##
##
##
##
##
##
##
##
63
62
61
60
59
58
55
54
53
52
51
50
2
18
4
2
5
56
57
on
on
on
on
on
on
on
on
on
on
on
on
on
on
on
on
on
on
on
U38
U38
U38
U38
U38
U38
U38
U38
U38
U38
U38
U38
U38
U32
U38
U32
U38
U38
U38
(thru series R111 47.5
(thru series R110 47.5
(thru series R109 47.5
(thru series R108 47.5
(thru series R107 47.5
(thru series R106 47.5
(thru series R105 47.5
(thru series R104 47.5
(thru series R103 47.5
(thru series R102 47.5
(thru series R101 47.5
(thru series R100 47.5
(thru series R112 47.5
(not wired to U38)
(thru series R113 47.5
(DVI_RESET_B pin 13 on
(thru series R114 47.5
"FLASH_A0"
"FLASH_A1"
"FLASH_A2"
"FLASH_A3"
"FLASH_A4"
"FLASH_A5"
"FLASH_A6"
"FLASH_A7"
"FLASH_A8"
"FLASH_A9"
"FLASH_A10"
"FLASH_A11"
"FLASH_A12"
"FLASH_A13"
"FLASH_A14"
"FLASH_A15"
"FLASH_A16"
"FLASH_A17"
"FLASH_A18"
"FLASH_A19"
"FLASH_A20"
LOC
LOC
LOC
LOC
LOC
LOC
LOC
LOC
LOC
LOC
LOC
LOC
LOC
LOC
LOC
LOC
LOC
LOC
LOC
LOC
LOC
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
"AL8";
"AK8";
"AC9";
"AD10";
"C8";
"B8";
"E9";
"E8";
"A8";
"A9";
"D9";
"C9";
"D10";
"C10";
"F10";
"F9";
"AH8";
"AG8";
"AP9";
"AN9";
"AF10";
##
##
##
##
##
##
##
##
##
##
##
##
##
##
##
##
##
##
##
##
##
29
25
24
23
22
21
20
19
8
7
6
5
4
3
2
1
55
18
17
16
11
on
on
on
on
on
on
on
on
on
on
on
on
on
on
on
on
on
on
on
on
on
U4,
U4,
U4,
U4,
U4,
U4,
U4,
U4,
U4,
U4,
U4,
U4,
U4,
U4,
U4,
U4,
U4,
U4,
U4,
U4,
U4,
A1
B1
C1
D1
D2
A2
C2
A3
B3
C3
D3
C4
A5
B5
C5
D7
D8
A7
B7
C7
C8
ML605 Hardware User Guide
UG534 (v1.2.1) January 21, 2010
www.xilinx.com
on
on
on
on
on
on
on
on
on
on
on
on
on
on
on
on
on
on
on
on
on
on
on
J1
J1
J1
J1
J1
J1
J1
J1
J1
J1
J1
J1
J1
J1
J1
J1
J1
J1
J1
J1
J1
J1
J1
on
on
on
on
on
on
on
on
on
on
on
on
on
on
on
on
on
on
on
on
on
ohm)
ohm)
ohm)
ohm)
ohm)
ohm)
ohm)
ohm)
ohm)
ohm)
ohm)
ohm)
ohm)
ohm)
U38)
ohm)
U27
U27
U27
U27
U27
U27
U27
U27
U27
U27
U27
U27
U27
U27
U27
U27
U27
U27
U27
U27
U27
81
Appendix C: ML605 Master UCF
NET
NET
NET
NET
NET
NET
NET
NET
NET
NET
NET
NET
NET
NET
NET
NET
NET
NET
NET
NET
NET
NET
NET
NET
NET
##
##
NET
NET
NET
NET
NET
NET
NET
NET
NET
NET
NET
NET
NET
NET
NET
NET
NET
NET
NET
NET
NET
NET
NET
NET
NET
NET
NET
NET
NET
NET
NET
NET
NET
NET
NET
NET
NET
NET
82
"FLASH_A21"
"FLASH_A22"
"FLASH_A23"
"FLASH_D0"
"FLASH_D1"
"FLASH_D2"
"FLASH_D3"
"FLASH_D4"
"FLASH_D5"
"FLASH_D6"
"FLASH_D7"
"FLASH_D8"
"FLASH_D9"
"FLASH_D10"
"FLASH_D11"
"FLASH_D12"
"FLASH_D13"
"FLASH_D14"
"FLASH_D15"
"FLASH_WAIT"
"FPGA_FWE_B"
"FPGA_FOE_B"
"FPGA_CCLK"
"PLATFLASH_L_B"
"FPGA_FCS_B"
"FMC_HPC_CLK0_M2C_N"
"FMC_HPC_CLK0_M2C_P"
"FMC_HPC_CLK1_M2C_N"
"FMC_HPC_CLK1_M2C_P"
"FMC_HPC_CLK2_M2C_IO_N"
"FMC_HPC_CLK2_M2C_IO_P"
"FMC_HPC_CLK2_M2C_MGT_C_N"
"FMC_HPC_CLK2_M2C_MGT_C_P"
"FMC_HPC_CLK3_M2C_IO_N"
"FMC_HPC_CLK3_M2C_IO_P"
"FMC_HPC_CLK3_M2C_MGT_C_N"
"FMC_HPC_CLK3_M2C_MGT_C_P"
"FMC_HPC_DP0_C2M_N"
"FMC_HPC_DP0_C2M_P"
"FMC_HPC_DP0_M2C_N"
"FMC_HPC_DP0_M2C_P"
"FMC_HPC_DP1_C2M_N"
"FMC_HPC_DP1_C2M_P"
"FMC_HPC_DP1_M2C_N"
"FMC_HPC_DP1_M2C_P"
"FMC_HPC_DP2_C2M_N"
"FMC_HPC_DP2_C2M_P"
"FMC_HPC_DP2_M2C_N"
"FMC_HPC_DP2_M2C_P"
"FMC_HPC_DP3_C2M_N"
"FMC_HPC_DP3_C2M_P"
"FMC_HPC_DP3_M2C_N"
"FMC_HPC_DP3_M2C_P"
"FMC_HPC_DP4_C2M_N"
"FMC_HPC_DP4_C2M_P"
"FMC_HPC_DP4_M2C_N"
"FMC_HPC_DP4_M2C_P"
"FMC_HPC_DP5_C2M_N"
"FMC_HPC_DP5_C2M_P"
"FMC_HPC_DP5_M2C_N"
"FMC_HPC_DP5_M2C_P"
"FMC_HPC_DP6_C2M_N"
"FMC_HPC_DP6_C2M_P"
LOC = "AF9";
LOC = "AL9";
LOC = "AA23";
LOC = "AF24";
LOC = "AF25";
LOC = "W24";
LOC = "V24";
LOC = "H24";
LOC = "H25";
LOC = "P24";
LOC = "R24";
LOC = "G23";
LOC = "H23";
LOC = "N24";
LOC = "N23";
LOC = "F23";
LOC = "F24";
LOC = "L24";
LOC = "M23";
LOC = "J26";
LOC = "AF23";
LOC = "AA24";
LOC = "K8";
LOC = "AC23";
LOC = "Y24";
LOC
LOC
LOC
LOC
LOC
LOC
LOC
LOC
LOC
LOC
LOC
LOC
LOC
LOC
LOC
LOC
LOC
LOC
LOC
LOC
LOC
LOC
LOC
LOC
LOC
LOC
LOC
LOC
LOC
LOC
LOC
LOC
LOC
LOC
LOC
LOC
LOC
LOC
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
"K23";
"K24";
"AP21";
"AP20";
"AC30";
"AD30";
"AB5";
"AB6";
"AF34";
"AE34";
"AH5";
"AH6";
"AB2";
"AB1";
"AC4";
"AC3";
"AD2";
"AD1";
"AE4";
"AE3";
"AF2";
"AF1";
"AF6";
"AF5";
"AH2";
"AH1";
"AG4";
"AG3";
"AK2";
"AK1";
"AJ4";
"AJ3";
"AM2";
"AM1";
"AL4";
"AL3";
"AN4";
"AN3";
## 10 on U4, A8 on U27
## 9 on U4, G1 on U27
## 26 on U4
## 34 on U4 (thru series R215
## 36 on U4 (thru series R216
## 39 on U4 (thru series R217
## 41 on U4 (thru series R218
## 47 on U4 (thru series R219
## 49 on U4 (thru series R220
## 51 on U4 (thru series R221
## 53 on U4 (thru series R222
## 35 on U4 (thru series R223
## 37 on U4 (thru series R224
## 40 on U4 (thru series R225
## 42 on U4 (thru series R226
## 48 on U4 (thru series R227
## 50 on U4 (thru series R228
## 52 on U4 (thru series R229
## 54 on U4 (thru series R230
## 56 on U4
## 14 on U4, G8 on U27
## 32 on U4, F8 on U27
##
F1 on U27
##
H1 on U27
## 30 on U4, B4 on U27 (U10 and
select either U4 or U27)
##
##
##
##
##
##
##
##
##
##
##
##
##
##
##
##
##
##
##
##
##
##
##
##
##
##
##
##
##
##
##
##
##
##
##
##
##
##
H5
H4
G3
G2
15
16
2
2
J3
J2
2
2
C3
C2
C7
C6
A23
A22
A3
A2
A27
A26
A7
A6
A31
A30
A11
A10
A35
A34
A15
A14
A39
A38
A19
A18
B37
B36
www.xilinx.com
on
on
on
on
on
on
on
on
on
on
on
on
on
on
on
on
on
on
on
on
on
on
on
on
on
on
on
on
on
on
on
on
on
on
on
on
on
on
J64
J64
J64
J64
U83
U83
series
series
J64
J64
series
series
J64
J64
J64
J64
J64
J64
J64
J64
J64
J64
J64
J64
J64
J64
J64
J64
J64
J64
J64
J64
J64
J64
J64
J64
J64
J64
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
ohm),
ohm),
ohm),
ohm),
ohm),
ohm),
ohm),
ohm),
ohm),
ohm),
ohm),
ohm),
ohm),
ohm),
ohm),
ohm),
F2
E2
G3
E4
E5
G5
G6
H7
E1
E3
F3
F4
F5
H5
G7
E7
on
on
on
on
on
on
on
on
on
on
on
on
on
on
on
on
U27
U27
U27
U27
U27
U27
U27
U27
U27
U27
U27
U27
U27
U27
U27
U27
switch S2.2 setting
C399 0.1uF
C398 0.1uF
C397 0.1uF
C396 0.1uF
ML605 Hardware User Guide
UG534 (v1.2.1) January 21, 2010
NET
NET
NET
NET
NET
NET
NET
NET
NET
NET
NET
NET
NET
NET
NET
NET
NET
NET
NET
NET
NET
NET
NET
NET
NET
NET
NET
NET
NET
NET
NET
NET
NET
NET
NET
NET
NET
NET
NET
NET
NET
NET
NET
NET
NET
NET
NET
NET
NET
NET
NET
NET
NET
NET
NET
NET
NET
NET
NET
NET
NET
NET
NET
NET
NET
"FMC_HPC_DP6_M2C_N"
"FMC_HPC_DP6_M2C_P"
"FMC_HPC_DP7_C2M_N"
"FMC_HPC_DP7_C2M_P"
"FMC_HPC_DP7_M2C_N"
"FMC_HPC_DP7_M2C_P"
"FMC_HPC_GBTCLK0_M2C_N"
"FMC_HPC_GBTCLK0_M2C_P"
"FMC_HPC_GBTCLK1_M2C_N"
"FMC_HPC_GBTCLK1_M2C_P"
"FMC_HPC_HA00_CC_N"
"FMC_HPC_HA00_CC_P"
"FMC_HPC_HA01_CC_N"
"FMC_HPC_HA01_CC_P"
"FMC_HPC_HA02_N"
"FMC_HPC_HA02_P"
"FMC_HPC_HA03_N"
"FMC_HPC_HA03_P"
"FMC_HPC_HA04_N"
"FMC_HPC_HA04_P"
"FMC_HPC_HA05_N"
"FMC_HPC_HA05_P"
"FMC_HPC_HA06_N"
"FMC_HPC_HA06_P"
"FMC_HPC_HA07_N"
"FMC_HPC_HA07_P"
"FMC_HPC_HA08_N"
"FMC_HPC_HA08_P"
"FMC_HPC_HA09_N"
"FMC_HPC_HA09_P"
"FMC_HPC_HA10_N"
"FMC_HPC_HA10_P"
"FMC_HPC_HA11_N"
"FMC_HPC_HA11_P"
"FMC_HPC_HA12_N"
"FMC_HPC_HA12_P"
"FMC_HPC_HA13_N"
"FMC_HPC_HA13_P"
"FMC_HPC_HA14_N"
"FMC_HPC_HA14_P"
"FMC_HPC_HA15_N"
"FMC_HPC_HA15_P"
"FMC_HPC_HA16_N"
"FMC_HPC_HA16_P"
"FMC_HPC_HA17_CC_N"
"FMC_HPC_HA17_CC_P"
"FMC_HPC_HA18_N"
"FMC_HPC_HA18_P"
"FMC_HPC_HA19_N"
"FMC_HPC_HA19_P"
"FMC_HPC_HA20_N"
"FMC_HPC_HA20_P"
"FMC_HPC_HA21_N"
"FMC_HPC_HA21_P"
"FMC_HPC_HA22_N"
"FMC_HPC_HA22_P"
"FMC_HPC_HA23_N"
"FMC_HPC_HA23_P"
"FMC_HPC_HB00_CC_N"
"FMC_HPC_HB00_CC_P"
"FMC_HPC_HB01_N"
"FMC_HPC_HB01_P"
"FMC_HPC_HB02_N"
"FMC_HPC_HB02_P"
"FMC_HPC_HB03_N"
ML605 Hardware User Guide
UG534 (v1.2.1) January 21, 2010
LOC
LOC
LOC
LOC
LOC
LOC
LOC
LOC
LOC
LOC
LOC
LOC
LOC
LOC
LOC
LOC
LOC
LOC
LOC
LOC
LOC
LOC
LOC
LOC
LOC
LOC
LOC
LOC
LOC
LOC
LOC
LOC
LOC
LOC
LOC
LOC
LOC
LOC
LOC
LOC
LOC
LOC
LOC
LOC
LOC
LOC
LOC
LOC
LOC
LOC
LOC
LOC
LOC
LOC
LOC
LOC
LOC
LOC
LOC
LOC
LOC
LOC
LOC
LOC
LOC
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
"AM6";
"AM5";
"AP2";
"AP1";
"AP6";
"AP5";
"AD5";
"AD6";
"AK5";
"AK6";
"AF33";
"AE33";
"AC29";
"AD29";
"AC25";
"AB25";
"Y26";
"AA25";
"AC28";
"AB28";
"AC27";
"AB27";
"AA29";
"AA28";
"AB26";
"AA26";
"AF31";
"AG31";
"AB31";
"AB30";
"AC34";
"AD34";
"AG32";
"AG33";
"AE32";
"AD32";
"AD31";
"AE31";
"AA31";
"AA30";
"AC32";
"AB32";
"AB33";
"AC33";
"W30";
"V30";
"T34";
"T33";
"U32";
"U33";
"V33";
"V32";
"U30";
"U31";
"V29";
"U28";
"U27";
"U26";
"AG30";
"AF30";
"AM32";
"AN32";
"AP33";
"AP32";
"AM31";
##
##
##
##
##
##
##
##
##
##
##
##
##
##
##
##
##
##
##
##
##
##
##
##
##
##
##
##
##
##
##
##
##
##
##
##
##
##
##
##
##
##
##
##
##
##
##
##
##
##
##
##
##
##
##
##
##
##
##
##
##
##
##
##
##
B17
B16
B33
B32
B13
B12
D5
D4
B21
B20
F5
F4
E3
E2
K8
K7
J7
J6
F8
F7
E7
E6
K11
K10
J10
J9
F11
F10
E10
E9
K14
K13
J13
J12
F14
F13
E13
E12
J16
J15
F17
F16
E16
E15
K17
K16
J19
J18
F20
F19
E19
E18
K20
K19
J22
J21
K23
K22
K26
K25
J25
J24
F23
F22
E22
www.xilinx.com
on
on
on
on
on
on
on
on
on
on
on
on
on
on
on
on
on
on
on
on
on
on
on
on
on
on
on
on
on
on
on
on
on
on
on
on
on
on
on
on
on
on
on
on
on
on
on
on
on
on
on
on
on
on
on
on
on
on
on
on
on
on
on
on
on
J64
J64
J64
J64
J64
J64
J64
J64
J64
J64
J64
J64
J64
J64
J64
J64
J64
J64
J64
J64
J64
J64
J64
J64
J64
J64
J64
J64
J64
J64
J64
J64
J64
J64
J64
J64
J64
J64
J64
J64
J64
J64
J64
J64
J64
J64
J64
J64
J64
J64
J64
J64
J64
J64
J64
J64
J64
J64
J64
J64
J64
J64
J64
J64
J64
83
Appendix C: ML605 Master UCF
NET
NET
NET
NET
NET
NET
NET
NET
NET
NET
NET
NET
NET
NET
NET
NET
NET
NET
NET
NET
NET
NET
NET
NET
NET
NET
NET
NET
NET
NET
NET
NET
NET
NET
NET
NET
NET
NET
NET
NET
NET
NET
NET
NET
NET
NET
NET
NET
NET
NET
NET
NET
NET
NET
NET
NET
NET
NET
NET
NET
NET
NET
NET
NET
NET
84
"FMC_HPC_HB03_P"
"FMC_HPC_HB04_N"
"FMC_HPC_HB04_P"
"FMC_HPC_HB05_N"
"FMC_HPC_HB05_P"
"FMC_HPC_HB06_CC_N"
"FMC_HPC_HB06_CC_P"
"FMC_HPC_HB07_N"
"FMC_HPC_HB07_P"
"FMC_HPC_HB08_N"
"FMC_HPC_HB08_P"
"FMC_HPC_HB09_N"
"FMC_HPC_HB09_P"
"FMC_HPC_HB10_N"
"FMC_HPC_HB10_P"
"FMC_HPC_HB11_N"
"FMC_HPC_HB11_P"
"FMC_HPC_HB12_N"
"FMC_HPC_HB12_P"
"FMC_HPC_HB13_N"
"FMC_HPC_HB13_P"
"FMC_HPC_HB14_N"
"FMC_HPC_HB14_P"
"FMC_HPC_HB15_N"
"FMC_HPC_HB15_P"
"FMC_HPC_HB16_N"
"FMC_HPC_HB16_P"
"FMC_HPC_HB17_CC_N"
"FMC_HPC_HB17_CC_P"
"FMC_HPC_HB18_N"
"FMC_HPC_HB18_P"
"FMC_HPC_HB19_N"
"FMC_HPC_HB19_P"
"FMC_HPC_LA00_CC_N"
"FMC_HPC_LA00_CC_P"
"FMC_HPC_LA01_CC_N"
"FMC_HPC_LA01_CC_P"
"FMC_HPC_LA02_N"
"FMC_HPC_LA02_P"
"FMC_HPC_LA03_N"
"FMC_HPC_LA03_P"
"FMC_HPC_LA04_N"
"FMC_HPC_LA04_P"
"FMC_HPC_LA05_N"
"FMC_HPC_LA05_P"
"FMC_HPC_LA06_N"
"FMC_HPC_LA06_P"
"FMC_HPC_LA07_N"
"FMC_HPC_LA07_P"
"FMC_HPC_LA08_N"
"FMC_HPC_LA08_P"
"FMC_HPC_LA09_N"
"FMC_HPC_LA09_P"
"FMC_HPC_LA10_N"
"FMC_HPC_LA10_P"
"FMC_HPC_LA11_N"
"FMC_HPC_LA11_P"
"FMC_HPC_LA12_N"
"FMC_HPC_LA12_P"
"FMC_HPC_LA13_N"
"FMC_HPC_LA13_P"
"FMC_HPC_LA14_N"
"FMC_HPC_LA14_P"
"FMC_HPC_LA15_N"
"FMC_HPC_LA15_P"
LOC
LOC
LOC
LOC
LOC
LOC
LOC
LOC
LOC
LOC
LOC
LOC
LOC
LOC
LOC
LOC
LOC
LOC
LOC
LOC
LOC
LOC
LOC
LOC
LOC
LOC
LOC
LOC
LOC
LOC
LOC
LOC
LOC
LOC
LOC
LOC
LOC
LOC
LOC
LOC
LOC
LOC
LOC
LOC
LOC
LOC
LOC
LOC
LOC
LOC
LOC
LOC
LOC
LOC
LOC
LOC
LOC
LOC
LOC
LOC
LOC
LOC
LOC
LOC
LOC
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
"AL30";
"AL33";
"AM33";
"AN34";
"AN33";
"AE26";
"AF26";
"AH34";
"AJ34";
"AK32";
"AK33";
"AK34";
"AL34";
"AF29";
"AF28";
"AJ30";
"AJ29";
"AJ32";
"AJ31";
"AH32";
"AH33";
"AD27";
"AE27";
"AE29";
"AE28";
"AH30";
"AH29";
"AG28";
"AG27";
"AD26";
"AD25";
"AK31";
"AL31";
"AF21";
"AF20";
"AL19";
"AK19";
"AD20";
"AC20";
"AD19";
"AC19";
"AE19";
"AF19";
"AH22";
"AG22";
"AG21";
"AG20";
"AJ21";
"AK21";
"AJ22";
"AK22";
"AL18";
"AM18";
"AL20";
"AM20";
"AN22";
"AM22";
"AL21";
"AM21";
"AN18";
"AP19";
"AN20";
"AN19";
"AL23";
"AM23";
##
##
##
##
##
##
##
##
##
##
##
##
##
##
##
##
##
##
##
##
##
##
##
##
##
##
##
##
##
##
##
##
##
##
##
##
##
##
##
##
##
##
##
##
##
##
##
##
##
##
##
##
##
##
##
##
##
##
##
##
##
##
##
##
##
E21
F26
F25
E25
E24
K29
K28
J28
J27
F29
F28
E28
E27
K32
K31
J31
J30
F32
F31
E31
E30
K35
K34
J34
J33
F35
F34
K38
K37
J37
J36
E34
E33
G7
G6
D9
D8
H8
H7
G10
G9
H11
H10
D12
D11
C11
C10
H14
H13
G13
G12
D15
D14
C15
C14
H17
H16
G16
G15
D18
D17
C19
C18
H20
H19
www.xilinx.com
on
on
on
on
on
on
on
on
on
on
on
on
on
on
on
on
on
on
on
on
on
on
on
on
on
on
on
on
on
on
on
on
on
on
on
on
on
on
on
on
on
on
on
on
on
on
on
on
on
on
on
on
on
on
on
on
on
on
on
on
on
on
on
on
on
J64
J64
J64
J64
J64
J64
J64
J64
J64
J64
J64
J64
J64
J64
J64
J64
J64
J64
J64
J64
J64
J64
J64
J64
J64
J64
J64
J64
J64
J64
J64
J64
J64
J64
J64
J64
J64
J64
J64
J64
J64
J64
J64
J64
J64
J64
J64
J64
J64
J64
J64
J64
J64
J64
J64
J64
J64
J64
J64
J64
J64
J64
J64
J64
J64
ML605 Hardware User Guide
UG534 (v1.2.1) January 21, 2010
NET
NET
NET
NET
NET
NET
NET
NET
NET
NET
NET
NET
NET
NET
NET
NET
NET
NET
NET
NET
NET
NET
NET
NET
NET
NET
NET
NET
NET
NET
NET
NET
NET
NET
NET
NET
NET
NET
##
NET
NET
NET
NET
NET
NET
NET
NET
NET
NET
NET
NET
NET
NET
NET
NET
NET
NET
NET
NET
NET
NET
NET
NET
NET
NET
"FMC_HPC_LA16_N"
"FMC_HPC_LA16_P"
"FMC_HPC_LA17_CC_N"
"FMC_HPC_LA17_CC_P"
"FMC_HPC_LA18_CC_N"
"FMC_HPC_LA18_CC_P"
"FMC_HPC_LA19_N"
"FMC_HPC_LA19_P"
"FMC_HPC_LA20_N"
"FMC_HPC_LA20_P"
"FMC_HPC_LA21_N"
"FMC_HPC_LA21_P"
"FMC_HPC_LA22_N"
"FMC_HPC_LA22_P"
"FMC_HPC_LA23_N"
"FMC_HPC_LA23_P"
"FMC_HPC_LA24_N"
"FMC_HPC_LA24_P"
"FMC_HPC_LA25_N"
"FMC_HPC_LA25_P"
"FMC_HPC_LA26_N"
"FMC_HPC_LA26_P"
"FMC_HPC_LA27_N"
"FMC_HPC_LA27_P"
"FMC_HPC_LA28_N"
"FMC_HPC_LA28_P"
"FMC_HPC_LA29_N"
"FMC_HPC_LA29_P"
"FMC_HPC_LA30_N"
"FMC_HPC_LA30_P"
"FMC_HPC_LA31_N"
"FMC_HPC_LA31_P"
"FMC_HPC_LA32_N"
"FMC_HPC_LA32_P"
"FMC_HPC_LA33_N"
"FMC_HPC_LA33_P"
"FMC_HPC_PG_M2C_LS"
"FMC_HPC_PRSNT_M2C_L"
LOC
LOC
LOC
LOC
LOC
LOC
LOC
LOC
LOC
LOC
LOC
LOC
LOC
LOC
LOC
LOC
LOC
LOC
LOC
LOC
LOC
LOC
LOC
LOC
LOC
LOC
LOC
LOC
LOC
LOC
LOC
LOC
LOC
LOC
LOC
LOC
LOC
LOC
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
"AN23";
"AP22";
"AM27";
"AN27";
"AJ25";
"AH25";
"AN24";
"AN25";
"AL24";
"AK23";
"AP29";
"AN29";
"AP26";
"AP27";
"AM26";
"AL26";
"AM30";
"AN30";
"AM28";
"AN28";
"AL25";
"AM25";
"AP31";
"AP30";
"AJ27";
"AK27";
"AK28";
"AL28";
"AK24";
"AJ24";
"AK29";
"AL29";
"AG26";
"AG25";
"AH24";
"AH23";
"J27";
"AP25";
##
##
##
##
##
##
##
##
##
##
##
##
##
##
##
##
##
##
##
##
##
##
##
##
##
##
##
##
##
##
##
##
##
##
##
##
##
##
G19
G18
D21
D20
C23
C22
H23
H22
G22
G21
H26
H25
G25
G24
D24
D23
H29
H28
G28
G27
D27
D26
C27
C26
H32
H31
G31
G30
H35
H34
G34
G33
H38
H37
G37
G36
F1
H2
on
on
on
on
on
on
on
on
on
on
on
on
on
on
on
on
on
on
on
on
on
on
on
on
on
on
on
on
on
on
on
on
on
on
on
on
on
on
J64
J64
J64
J64
J64
J64
J64
J64
J64
J64
J64
J64
J64
J64
J64
J64
J64
J64
J64
J64
J64
J64
J64
J64
J64
J64
J64
J64
J64
J64
J64
J64
J64
J64
J64
J64
J64
J64
"FMC_LPC_CLK0_M2C_N"
"FMC_LPC_CLK0_M2C_P"
"FMC_LPC_CLK1_M2C_N"
"FMC_LPC_CLK1_M2C_P"
"FMC_LPC_DP0_C2M_N"
"FMC_LPC_DP0_C2M_P"
"FMC_LPC_DP0_M2C_N"
"FMC_LPC_DP0_M2C_P"
"FMC_LPC_GBTCLK0_M2C_N"
"FMC_LPC_GBTCLK0_M2C_P"
"FMC_LPC_IIC_SCL_LS"
"FMC_LPC_IIC_SDA_LS"
"FMC_LPC_LA00_CC_N"
"FMC_LPC_LA00_CC_P"
"FMC_LPC_LA01_CC_N"
"FMC_LPC_LA01_CC_P"
"FMC_LPC_LA02_N"
"FMC_LPC_LA02_P"
"FMC_LPC_LA03_N"
"FMC_LPC_LA03_P"
"FMC_LPC_LA04_N"
"FMC_LPC_LA04_P"
"FMC_LPC_LA05_N"
"FMC_LPC_LA05_P"
"FMC_LPC_LA06_N"
"FMC_LPC_LA06_P"
LOC
LOC
LOC
LOC
LOC
LOC
LOC
LOC
LOC
LOC
LOC
LOC
LOC
LOC
LOC
LOC
LOC
LOC
LOC
LOC
LOC
LOC
LOC
LOC
LOC
LOC
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
"B10";
"A10";
"G33";
"F33";
"D2";
"D1";
"G4";
"G3";
"M5";
"M6";
"AF13";
"AG13";
"K27";
"K26";
"E31";
"F31";
"H30";
"G31";
"J32";
"J31";
"J29";
"K28";
"H33";
"H34";
"J34";
"K33";
##
##
##
##
##
##
##
##
##
##
##
##
##
##
##
##
##
##
##
##
##
##
##
##
##
##
H5
H4
G3
G2
C3
C2
C7
C6
D5
D4
2
2
G7
G6
D9
D8
H8
H7
G10
G9
H11
H10
D12
D11
C11
C10
on
on
on
on
on
on
on
on
on
on
of
of
on
on
on
on
on
on
on
on
on
on
on
on
on
on
J63
J63
J63
J63
J63
J63
J63
J63
J63
J63
Q26
Q27
J63
J63
J63
J63
J63
J63
J63
J63
J63
J63
J63
J63
J63
J63
ML605 Hardware User Guide
UG534 (v1.2.1) January 21, 2010
www.xilinx.com
85
Appendix C: ML605 Master UCF
NET "FMC_LPC_LA07_N"
NET "FMC_LPC_LA07_P"
NET "FMC_LPC_LA08_N"
NET "FMC_LPC_LA08_P"
NET "FMC_LPC_LA09_N"
NET "FMC_LPC_LA09_P"
NET "FMC_LPC_LA10_N"
NET "FMC_LPC_LA10_P"
NET "FMC_LPC_LA11_N"
NET "FMC_LPC_LA11_P"
NET "FMC_LPC_LA12_N"
NET "FMC_LPC_LA12_P"
NET "FMC_LPC_LA13_N"
NET "FMC_LPC_LA13_P"
NET "FMC_LPC_LA14_N"
NET "FMC_LPC_LA14_P"
NET "FMC_LPC_LA15_N"
NET "FMC_LPC_LA15_P"
NET "FMC_LPC_LA16_N"
NET "FMC_LPC_LA16_P"
NET "FMC_LPC_LA17_CC_N"
NET "FMC_LPC_LA17_CC_P"
NET "FMC_LPC_LA18_CC_N"
NET "FMC_LPC_LA18_CC_P"
NET "FMC_LPC_LA19_N"
NET "FMC_LPC_LA19_P"
NET "FMC_LPC_LA20_N"
NET "FMC_LPC_LA20_P"
NET "FMC_LPC_LA21_N"
NET "FMC_LPC_LA21_P"
NET "FMC_LPC_LA22_N"
NET "FMC_LPC_LA22_P"
NET "FMC_LPC_LA23_N"
NET "FMC_LPC_LA23_P"
NET "FMC_LPC_LA24_N"
NET "FMC_LPC_LA24_P"
NET "FMC_LPC_LA25_N"
NET "FMC_LPC_LA25_P"
NET "FMC_LPC_LA26_N"
NET "FMC_LPC_LA26_P"
NET "FMC_LPC_LA27_N"
NET "FMC_LPC_LA27_P"
NET "FMC_LPC_LA28_N"
NET "FMC_LPC_LA28_P"
NET "FMC_LPC_LA29_N"
NET "FMC_LPC_LA29_P"
NET "FMC_LPC_LA30_N"
NET "FMC_LPC_LA30_P"
NET "FMC_LPC_LA31_N"
NET "FMC_LPC_LA31_P"
NET "FMC_LPC_LA32_N"
NET "FMC_LPC_LA32_P"
NET "FMC_LPC_LA33_N"
NET "FMC_LPC_LA33_P"
NET "FMC_LPC_PRSNT_M2C_L"
##
## NET "FPGA_CCLK"
NET "FPGA_DONE"
NET "FPGA_DX_N"
NET "FPGA_DX_P"
## NET "FPGA_FCS_B"
## NET "FPGA_FOE_B"
## NET "FPGA_FWE_B"
##
NET "FPGA_INIT_B"
86
LOC
LOC
LOC
LOC
LOC
LOC
LOC
LOC
LOC
LOC
LOC
LOC
LOC
LOC
LOC
LOC
LOC
LOC
LOC
LOC
LOC
LOC
LOC
LOC
LOC
LOC
LOC
LOC
LOC
LOC
LOC
LOC
LOC
LOC
LOC
LOC
LOC
LOC
LOC
LOC
LOC
LOC
LOC
LOC
LOC
LOC
LOC
LOC
LOC
LOC
LOC
LOC
LOC
LOC
LOC
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
"H32";
"G32";
"K29";
"J30";
"L26";
"L25";
"G30";
"F30";
"D32";
"D31";
"E33";
"E32";
"C34";
"D34";
"B34";
"C33";
"B32";
"C32";
"B33";
"A33";
"N29";
"N28";
"L30";
"L29";
"N30";
"M30";
"R29";
"P29";
"T26";
"R26";
"P27";
"N27";
"R27";
"R28";
"P32";
"N32";
"P30";
"P31";
"M32";
"L33";
"R32";
"R31";
"M33";
"N33";
"P34";
"N34";
"M27";
"M26";
"L31";
"M31";
"M25";
"N25";
"K31";
"K32";
"AD9";
##
##
##
##
##
##
##
##
##
##
##
##
##
##
##
##
##
##
##
##
##
##
##
##
##
##
##
##
##
##
##
##
##
##
##
##
##
##
##
##
##
##
##
##
##
##
##
##
##
##
##
##
##
##
##
H14
H13
G13
G12
D15
D14
C15
C14
H17
H16
G16
G15
D18
D17
C19
C18
H20
H19
G19
G18
D21
D20
C23
C22
H23
H22
G22
G21
H26
H25
G25
G24
D24
D23
H29
H28
G28
G27
D27
D26
C27
C26
H32
H31
G31
G30
H35
H34
G34
G33
H38
H37
G37
G36
H2
on
on
on
on
on
on
on
on
on
on
on
on
on
on
on
on
on
on
on
on
on
on
on
on
on
on
on
on
on
on
on
on
on
on
on
on
on
on
on
on
on
on
on
on
on
on
on
on
on
on
on
on
on
on
on
LOC
LOC
LOC
LOC
LOC
LOC
LOC
=
=
=
=
=
=
=
"K8";
"R8";
"W17";
"W18";
"Y24";
"AA24";
"AF23";
##
##
##
##
##
##
##
SEE
2
4
2
SEE
SEE
SEE
NET "FLASH_NN" GROUP
on "DONE" LED DS13
on J35
on J35
NET "FLASH_NN" GROUP
NET "FLASH_NN" GROUP
NET "FLASH_NN" GROUP
LOC = "P8";
## 1
www.xilinx.com
J63
J63
J63
J63
J63
J63
J63
J63
J63
J63
J63
J63
J63
J63
J63
J63
J63
J63
J63
J63
J63
J63
J63
J63
J63
J63
J63
J63
J63
J63
J63
J63
J63
J63
J63
J63
J63
J63
J63
J63
J63
J63
J63
J63
J63
J63
J63
J63
J63
J63
J63
J63
J63
J63
J63
on Q14 ("INIT" LED DS31 driver)
ML605 Hardware User Guide
UG534 (v1.2.1) January 21, 2010
NET
NET
NET
NET
NET
NET
NET
NET
##
NET
NET
NET
NET
NET
NET
NET
NET
##
NET
NET
NET
NET
NET
NET
NET
NET
##
NET
NET
NET
NET
NET
##
NET
NET
NET
NET
NET
##
NET
NET
NET
NET
NET
NET
##
NET
NET
NET
NET
NET
NET
NET
##
NET
##
NET
NET
NET
NET
NET
NET
NET
NET
NET
"FPGA_M0"
"FPGA_M1"
"FPGA_M2"
"FPGA_PROG_B"
"FPGA_TCK"
"FPGA_TDI"
"FPGA_TMS"
"FPGA_VBATT"
LOC
LOC
LOC
LOC
LOC
LOC
LOC
LOC
=
=
=
=
=
=
=
=
"U8";
"W8";
"V8";
"L8";
"AE8";
"AD8";
"AF8";
"N8";
##
##
##
##
##
##
##
##
3
4
4
1
80
82
85
1
on
on
on
on
on
on
on
on
S2 DIP switch (active-High)
S2 DIP switch (active-High)
S2 DIP switch (active-High)
SW4 pushbutton (active-Low)
U19
U19
U19
B1 (battery + terminal)
"GPIO_DIP_SW1"
"GPIO_DIP_SW2"
"GPIO_DIP_SW3"
"GPIO_DIP_SW4"
"GPIO_DIP_SW5"
"GPIO_DIP_SW6"
"GPIO_DIP_SW7"
"GPIO_DIP_SW8"
LOC
LOC
LOC
LOC
LOC
LOC
LOC
LOC
=
=
=
=
=
=
=
=
"D22";
"C22";
"L21";
"L20";
"C18";
"B18";
"K22";
"K21";
##
##
##
##
##
##
##
##
1
2
3
4
5
6
7
8
on
on
on
on
on
on
on
on
SW1
SW1
SW1
SW1
SW1
SW1
SW1
SW1
DIP
DIP
DIP
DIP
DIP
DIP
DIP
DIP
"GPIO_LED_0"
"GPIO_LED_1"
"GPIO_LED_2"
"GPIO_LED_3"
"GPIO_LED_4"
"GPIO_LED_5"
"GPIO_LED_6"
"GPIO_LED_7"
LOC
LOC
LOC
LOC
LOC
LOC
LOC
LOC
=
=
=
=
=
=
=
=
"AC22";
"AC24";
"AE22";
"AE23";
"AB23";
"AG23";
"AE24";
"AD24";
##
##
##
##
##
##
##
##
2
2
2
2
2
2
2
2
on
on
on
on
on
on
on
on
LED
LED
LED
LED
LED
LED
LED
LED
DS12,
DS11,
DS9,
DS10,
DS15,
DS14,
DS22,
DS21,
"GPIO_LED_C"
"GPIO_LED_E"
"GPIO_LED_N"
"GPIO_LED_S"
"GPIO_LED_W"
LOC
LOC
LOC
LOC
LOC
=
=
=
=
=
"AP24";
"AE21";
"AH27";
"AH28";
"AD21";
##
##
##
##
##
2
2
2
2
2
on
on
on
on
on
LED
LED
LED
LED
LED
DS16
DS19
DS20
DS18
DS17
"GPIO_SW_C"
"GPIO_SW_E"
"GPIO_SW_N"
"GPIO_SW_S"
"GPIO_SW_W"
LOC
LOC
LOC
LOC
LOC
=
=
=
=
=
"G26";
"G17";
"A19";
"A18";
"H17";
##
##
##
##
##
2
2
2
2
2
on
on
on
on
on
SW9
SW7
SW5
SW6
SW8
pushbutton
pushbutton
pushbutton
pushbutton
pushbutton
"IIC_SCL_DVI"
"IIC_SCL_MAIN_LS"
"IIC_SCL_SFP"
"IIC_SDA_DVI"
"IIC_SDA_MAIN_LS"
"IIC_SDA_SFP"
LOC
LOC
LOC
LOC
LOC
LOC
=
=
=
=
=
=
"AN10";
"AK9";
"AA34";
"AP10";
"AE9";
"AA33";
##
##
##
##
##
##
2
2
2
2
2
2
on
on
on
on
on
on
Q5, 15 on U38
Q19
Q23
Q6, 14 on U38
Q20
Q21
"LCD_DB4_LS"
"LCD_DB5_LS"
"LCD_DB6_LS"
"LCD_DB7_LS"
"LCD_E_LS"
"LCD_RS_LS"
"LCD_RW_LS"
LOC
LOC
LOC
LOC
LOC
LOC
LOC
=
=
=
=
=
=
=
"AD14";
"AK11";
"AJ11";
"AE12";
"AK12";
"T28";
"AC14";
##
##
##
##
##
##
##
4
3
2
1
9
11
10
on
on
on
on
on
on
on
J41
J41
J41
J41
J41
J41
J41
"P30_CS_SEL"
LOC = "AJ12";
## 2
on S2 DIP switch (active-High),1 on U10
"PCIE_100M_MGT0_N"
"PCIE_100M_MGT0_P"
"PCIE_250M_MGT1_N"
"PCIE_250M_MGT1_P"
"PCIE_PERST_B_LS"
"PCIE_RX0_N"
"PCIE_RX0_P"
"PCIE_RX1_N"
"PCIE_RX1_P"
LOC
LOC
LOC
LOC
LOC
LOC
LOC
LOC
LOC
##
##
##
##
##
##
##
##
##
on
on
on
on
on
on
on
on
on
ML605 Hardware User Guide
UG534 (v1.2.1) January 21, 2010
=
=
=
=
=
=
=
=
=
"P5";
"P6";
"V5";
"V6";
"AE13";
"J4";
"J3";
"K6";
"K5";
15
16
18
17
4
B15
B14
B20
B19
www.xilinx.com
switch
switch
switch
switch
switch
switch
switch
switch
1
2
3
4
5
6
7
8
on
on
on
on
on
on
on
on
(active-High)
(active-High)
(active-High)
(active-High)
(active-High)
(active-High)
(active-High)
(active-High)
J62
J62
J62
J62
J62
J62
J62
J62
(active-High)
(active-High)
(active-High)
(active-High)
(active-High)
U14
U14
U9
U9
U32
P1
P1
P1
P1
87
Appendix C: ML605 Master UCF
NET "PCIE_RX2_N"
NET "PCIE_RX2_P"
NET "PCIE_RX3_N"
NET "PCIE_RX3_P"
NET "PCIE_RX4_N"
NET "PCIE_RX4_P"
NET "PCIE_RX5_N"
NET "PCIE_RX5_P"
NET "PCIE_RX6_N"
NET "PCIE_RX6_P"
NET "PCIE_RX7_N"
NET "PCIE_RX7_P"
NET "PCIE_TX0_N"
NET "PCIE_TX0_P"
NET "PCIE_TX1_N"
NET "PCIE_TX1_P"
NET "PCIE_TX2_N"
NET "PCIE_TX2_P"
NET "PCIE_TX3_N"
NET "PCIE_TX3_P"
NET "PCIE_TX4_N"
NET "PCIE_TX4_P"
NET "PCIE_TX5_N"
NET "PCIE_TX5_P"
NET "PCIE_TX6_N"
NET "PCIE_TX6_P"
NET "PCIE_TX7_N"
NET "PCIE_TX7_P"
NET "PCIE_WAKE_B_LS"
##
NET "PHY_COL"
NET "PHY_CRS"
NET "PHY_INT"
NET "PHY_MDC"
NET "PHY_MDIO"
NET "PHY_RESET"
NET "PHY_RXCLK"
NET "PHY_RXCTL_RXDV"
NET "PHY_RXD0"
NET "PHY_RXD1"
NET "PHY_RXD2"
NET "PHY_RXD3"
NET "PHY_RXD4"
NET "PHY_RXD5"
NET "PHY_RXD6"
NET "PHY_RXD7"
NET "PHY_RXER"
NET "PHY_TXCLK"
NET "PHY_TXCTL_TXEN"
NET "PHY_TXC_GTXCLK"
NET "PHY_TXD0"
NET "PHY_TXD1"
NET "PHY_TXD2"
NET "PHY_TXD3"
NET "PHY_TXD4"
NET "PHY_TXD5"
NET "PHY_TXD6"
NET "PHY_TXD7"
NET "PHY_TXER"
##
## NET "PLATFLASH_L_B"
##
NET "PMBUS_ALERT_LS"
NET "PMBUS_CLK_LS"
NET "PMBUS_CTRL_LS"
88
LOC
LOC
LOC
LOC
LOC
LOC
LOC
LOC
LOC
LOC
LOC
LOC
LOC
LOC
LOC
LOC
LOC
LOC
LOC
LOC
LOC
LOC
LOC
LOC
LOC
LOC
LOC
LOC
LOC
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
"L4";
"L3";
"N4";
"N3";
"R4";
"R3";
"U4";
"U3";
"W4";
"W3";
"AA4";
"AA3";
"F2";
"F1";
"H2";
"H1";
"K2";
"K1";
"M2";
"M1";
"P2";
"P1";
"T2";
"T1";
"V2";
"V1";
"Y2";
"Y1";
"AD22";
##
##
##
##
##
##
##
##
##
##
##
##
##
##
##
##
##
##
##
##
##
##
##
##
##
##
##
##
##
B24
B23
B28
B27
B34
B33
B38
B37
B42
B41
B46
B45
A17
A16
A22
A21
A26
A25
A30
A29
A36
A35
A40
A39
A44
A43
A48
A47
B11
on
on
on
on
on
on
on
on
on
on
on
on
on
on
on
on
on
on
on
on
on
on
on
on
on
on
on
on
on
P1
P1
P1
P1
P1
P1
P1
P1
P1
P1
P1
P1
P1
P1
P1
P1
P1
P1
P1
P1
P1
P1
P1
P1
P1
P1
P1
P1
P1
LOC
LOC
LOC
LOC
LOC
LOC
LOC
LOC
LOC
LOC
LOC
LOC
LOC
LOC
LOC
LOC
LOC
LOC
LOC
LOC
LOC
LOC
LOC
LOC
LOC
LOC
LOC
LOC
LOC
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
"AK13";
"AL13";
"AH14";
"AP14";
"AN14";
"AH13";
"AP11";
"AM13";
"AN13";
"AF14";
"AE14";
"AN12";
"AM12";
"AD11";
"AC12";
"AC13";
"AG12";
"AD12";
"AJ10";
"AH12";
"AM11";
"AL11";
"AG10";
"AG11";
"AL10";
"AM10";
"AE11";
"AF11";
"AH10";
##
##
##
##
##
##
##
##
##
##
##
##
##
##
##
##
##
##
##
##
##
##
##
##
##
##
##
##
##
114
115
32
35
33
36
7
4
3
128
126
125
124
123
121
120
9
10
16
14
18
19
20
24
25
26
28
29
13
on
on
on
on
on
on
on
on
on
on
on
on
on
on
on
on
on
on
on
on
on
on
on
on
on
on
on
on
on
U80
U80
U80
U80
U80
U80
U80
U80
U80
U80
U80
U80
U80
U80
U80
U80
U80
U80
U80
U80
U80
U80
U80
U80
U80
U80
U80
U80
U80
LOC = "AC23";
## SEE NET "FLASH_NN" GROUP
LOC = "AH9";
LOC = "AC10";
LOC = "AJ9";
## 2
## 2
## 2
www.xilinx.com
on Q15
on Q18
on Q16
ML605 Hardware User Guide
UG534 (v1.2.1) January 21, 2010
NET
##
NET
NET
NET
NET
NET
NET
##
NET
NET
NET
NET
NET
NET
##
NET
NET
NET
NET
NET
NET
##
NET
NET
##
NET
NET
NET
NET
NET
NET
NET
NET
NET
NET
NET
NET
NET
NET
NET
NET
NET
NET
NET
NET
NET
##
NET
NET
##
NET
NET
NET
NET
##
NET
NET
NET
NET
NET
NET
NET
NET
NET
"PMBUS_DATA_LS"
LOC = "AB10";
## 2
on Q17
"SFP_LOS"
"SFP_RX_N"
"SFP_RX_P"
"SFP_TX_DISABLE_FPGA"
"SFP_TX_N"
"SFP_TX_P"
LOC
LOC
LOC
LOC
LOC
LOC
=
=
=
=
=
=
"V23";
"E4";
"E3";
"AP12";
"C4";
"C3";
##
##
##
##
##
##
8
12
13
1
19
18
on
on
on
on
on
on
P4
P4
P4
Q22
P4
P4
"SGMIICLK_QO_N"
"SGMIICLK_QO_P"
"SGMII_RX_N"
"SGMII_RX_P"
"SGMII_TX_N"
"SGMII_TX_P"
LOC
LOC
LOC
LOC
LOC
LOC
=
=
=
=
=
=
"H5";
"H6";
"B6";
"B5";
"A4";
"A3";
##
##
##
##
##
##
2
2
1
1
1
1
on
on
on
on
on
on
series
series
series
series
series
series
"SMA_REFCLK_N"
"SMA_REFCLK_P"
"SMA_RX_N"
"SMA_RX_P"
"SMA_TX_N"
"SMA_TX_P"
LOC
LOC
LOC
LOC
LOC
LOC
=
=
=
=
=
=
"F5";
"F6";
"D6";
"D5";
"B2";
"B1";
##
##
##
##
##
##
1
1
1
1
1
1
on
on
on
on
on
on
series C61
series C62
series C57
series C58
J27 SMA
J26 SMA
"SM_FAN_PWM"
"SM_FAN_TACH"
LOC = "L10";
LOC = "M10";
## 1
## 2
on Q24
on R368
"SYSACE_CFGTDI"
"SYSACE_D0"
"SYSACE_D1"
"SYSACE_D2"
"SYSACE_D3"
"SYSACE_D4"
"SYSACE_D5"
"SYSACE_D6"
"SYSACE_D7"
"SYSACE_MPA00"
"SYSACE_MPA01"
"SYSACE_MPA02"
"SYSACE_MPA03"
"SYSACE_MPA04"
"SYSACE_MPA05"
"SYSACE_MPA06"
"SYSACE_MPBRDY"
"SYSACE_MPCE"
"SYSACE_MPIRQ"
"SYSACE_MPOE"
"SYSACE_MPWE"
LOC
LOC
LOC
LOC
LOC
LOC
LOC
LOC
LOC
LOC
LOC
LOC
LOC
LOC
LOC
LOC
LOC
LOC
LOC
LOC
LOC
##
##
##
##
##
##
##
##
##
##
##
##
##
##
##
##
##
##
##
##
##
on
on
on
on
on
on
on
on
on
on
on
on
on
on
on
on
on
on
on
on
on
"SYSCLK_N"
"SYSCLK_P"
LOC = "H9";
LOC = "J9";
## 5
## 4
on U11, 5 on U89 (DNP)
on U11, 4 on U89 (DNP)
"USB_1_CTS"
"USB_1_RTS"
"USB_1_RX"
"USB_1_TX"
LOC
LOC
LOC
LOC
=
=
=
=
"T24";
"T23";
"J25";
"J24";
##
##
##
##
22
23
24
25
on
on
on
on
U34
U34
U34
U34
"USB_A0_LS"
"USB_A1_LS"
"USB_CS_B_LS"
"USB_D0_LS"
"USB_D1_LS"
"USB_D2_LS"
"USB_D3_LS"
"USB_D4_LS"
"USB_D5_LS"
LOC
LOC
LOC
LOC
LOC
LOC
LOC
LOC
LOC
=
=
=
=
=
=
=
=
=
"Y32";
"W26";
"W27";
"R33";
"R34";
"T30";
"T31";
"T29";
"V28";
##
##
##
##
##
##
##
##
##
14
2
18
8
14
6
16
4
18
on
on
on
on
on
on
on
on
on
U30
U29
U29
U31
U31
U31
U31
U31
U31
ML605 Hardware User Guide
UG534 (v1.2.1) January 21, 2010
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
"AC8";
"AM15";
"AJ17";
"AJ16";
"AP16";
"AG16";
"AH15";
"AF16";
"AN15";
"AC15";
"AP15";
"AG17";
"AH17";
"AG15";
"AF15";
"AK14";
"AJ15";
"AJ14";
"L9";
"AL15";
"AL14";
81
66
65
63
62
61
60
59
58
70
69
68
67
45
44
43
39
42
41
77
76
www.xilinx.com
C55 0.1uF
C56 0.1uF
C163 0.01uF
C162 0.01uF
C164 0.01uF
C165 0.01uF
0.1uF
0.1uF
0.1uF
0.1uF
U19
U19
U19
U19
U19
U19
U19
U19
U19
U19
U19
U19
U19
U19
U19
U19
U19
U19
U19
U19
U19
89
Appendix C: ML605 Master UCF
NET
NET
NET
NET
NET
NET
NET
NET
NET
NET
NET
NET
NET
NET
##
NET
NET
NET
NET
NET
##
NET
NET
NET
NET
90
"USB_D6_LS"
"USB_D7_LS"
"USB_D8_LS"
"USB_D9_LS"
"USB_D10_LS"
"USB_D11_LS"
"USB_D12_LS"
"USB_D13_LS"
"USB_D14_LS"
"USB_D15_LS"
"USB_INT_LS"
"USB_RD_B_LS"
"USB_RESET_B_LS"
"USB_WR_B_LS"
LOC
LOC
LOC
LOC
LOC
LOC
LOC
LOC
LOC
LOC
LOC
LOC
LOC
LOC
=
=
=
=
=
=
=
=
=
=
=
=
=
=
"V27";
"U25";
"Y28";
"W32";
"W31";
"Y29";
"W29";
"Y34";
"Y33";
"Y31";
"Y27";
"W25";
"T25";
"V25";
##
##
##
##
##
##
##
##
##
##
##
##
##
##
2
12
14
8
12
2
18
4
16
6
6
16
8
4
on
on
on
on
on
on
on
on
on
on
on
on
on
on
U31
U30
U29
U29
U29
U30
U30
U30
U30
U30
U29
U29
U30
U29
"USER_CLOCK"
"USER_SMA_CLOCK_N"
"USER_SMA_CLOCK_P"
"USER_SMA_GPIO_N"
"USER_SMA_GPIO_P"
LOC
LOC
LOC
LOC
LOC
=
=
=
=
=
"U23";
"M22";
"L23";
"W34";
"V34";
##
##
##
##
##
5
1
1
1
1
on
on
on
on
on
X5
J55
J58
J56
J57
"VAUX_CURR_N"
"VAUX_CURR_P"
"VAUX_VOLT_N"
"VAUX_VOLT_P"
LOC
LOC
LOC
LOC
=
=
=
=
"P26";
"P25";
"M28";
"L28";
##
##
##
##
1
1
1
1
on
on
on
on
series
series
series
series
www.xilinx.com
SMA
SMA
SMA
SMA
R373
R370
R371
R372
1.00K
1.00K
1.00K
1.00K
ML605 Hardware User Guide
UG534 (v1.2.1) January 21, 2010
Appendix D
References
This section provides references to documentation supporting Virtex-6 FPGAs, tools, and
IP. For additional information, see www.xilinx.com/support/documentation/index.htm.
Documents supporting the ML605 Evaluation Board:
1.
UG535, ML605 Reference Design User Guide
2.
UG525, Getting Started with the Xilinx Virtex-6 FPGA ML605 Evaluation Kit
3.
DS150, Virtex-6 Family Overview
4.
DS152, Viretx-6 FPGA Data Sheet: DC and Switching Characteristics
5.
UG360, Virtex-6 FPGA Configuration User Guide
6.
UG406, Virtex-6 FPGA Memory Interface Solutions User Guide
7.
UG361, Virtex-6 FPGA SelectIO Resources User Guide
8.
UG362, Virtex-6 FPGA User Guide: Clocking Resources
9.
UG363, Virtex-6 FPGA Memory Resources User Guide
10. UG364, Virtex-6 FPGA Configurable Logic Block User Guide
11. UG365, Virtex-6 FPGA Packaging and Pinout Specifications
12. UG366, Virtex-6 FPGA GTX Transceivers User Guide
13. UG369, Virtex-6 FPGA DSP48E1 Slice User Guide
14. DS186, Virtex-6 FPGA Memory Interface Solutions Data Sheet
15. UG370, Virtex-6 FPGA System Monitor User Guide
16. DS715, Virtex-6 FPGA Integrated Block v1.2 for PCI Express Data Sheet
17. DS617, Platform Flash XL High-Density Configuration and Storage Device Data Sheet
18. DS080, System ACE CompactFlash Solution Data Sheet
19. UG138, LogiCORE™ IP Tri-Mode Ethernet MAC v4.2 User Guide
20. DS581, XPS External Peripheral Controller (EPC) v1.02a Data Sheet
21. DS606, XPS IIC Bus Interface (v2.00a) Data Sheet
ML605 Hardware User Guide
UG534 (v1.2.1) January 21, 2010
www.xilinx.com
91
Appendix D: References
Additional documentation:
22. Micron Technology, Inc., DDR3 SODIMM Specification (MT4JSF6464HY-1G1)
23. Winbond, Serial Flash Memory Data Sheet (W25Q64VSFIG)
24. Numonyx, Embedded Flash Memory Data Sheet (TE28F128J3D-75)
25. Epson Toyocom, Oscillator Data Sheet (EG-2121CA-200.0000M-LHPA)
26. MMD Components, MBH Series Data Sheet (MBH2100H-66.000 MHz)
27. PCI SIG, PCI Express Specifications
28. Marvell, Alaska Gigabit Ethernet Transceivers Product Page
29. Cypress Semiconductor, CY7C67300 Data Sheet
30. USB Implementers Forum, Inc., USB Specifications
31. ST Micro, M24C08 Data Sheet
32. Samtec, Inc.
92
www.xilinx.com
ML605 Hardware User Guide
UG534 (v1.2.1) January 21, 2010
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.4 Linearized : Yes Page Mode : UseOutlines XMP Toolkit : 3.1-701 Producer : Acrobat Distiller 7.0.5 (Windows) Keywords : ML605, Virtex-6, board, PCB Creator Tool : FrameMaker 7.2 Modify Date : 2010:01:20 13:52:43Z Create Date : 2010:01:20 13:47:18Z Format : application/pdf Title : Xilinx UG534 ML605 Hardware, User Guide Creator : Xilinx, Inc. Description : This user guide documents the Virtex-6 FPGA ML605 Evaluation board. Document ID : uuid:23ee55d4-aae7-49d1-b35a-84b1d27306bc Instance ID : uuid:ba21a55f-b9da-4f5d-b352-5afe1ca62532 Page Count : 92 Subject : This user guide documents the Virtex-6 FPGA ML605 Evaluation board. Author : Xilinx, Inc.EXIF Metadata provided by EXIF.tools