User Manual
| Download: |  |
| Mirror Download [FCC.gov] | |
| Document ID | 360449 |
| Application ID | fW+GjMlK0aGcJlc5vWjHeQ== |
| Document Description | User Manual |
| Short Term Confidential | No |
| Permanent Confidential | No |
| Supercede | No |
| Document Type | User Manual |
| Display Format | Adobe Acrobat PDF - pdf |
| Filesize | 105.3kB (1316214 bits) |
| Date Submitted | 2003-09-26 00:00:00 |
| Date Available | 2003-09-26 00:00:00 |
| Creation Date | 2003-08-12 22:46:50 |
| Producing Software | Acrobat Distiller 5.0 (Windows) |
| Document Lastmod | 2003-08-28 15:16:54 |
| Document Title | Microsoft Word - TAGLINK - user manual.doc |
| Document Creator | PScript5.dll Version 5.2 |
| Document Author: | bruce |
User Manual - INTRODUCTION TAG LINK The eXI Tag Link device automates tag administration by providing a localized eLink between the Halo or Assetrac application software and the targeted tag device. The Tag Link communicates directly with the system computer through a serial port and may be powered by an internal 9 volt battery or accessory AC wall adapter. The Tag Link enables the software application to transparently interact with the tags. Tag Link Views PHOTO ILLUS: TAG LINK WITH PTAG WITH LED HIGHLIGHTED PHOTO ILLUS: TAG LINK WITH MOTHER TAG Copyright 2003 - eXI Wireless Systems Inc. Page XX 980-000003 – 002. R1.01 User Manual - INTRODUCTION Tag Link Range The communication range for Tag Link is designed to be typically less than 12 inches. Therefore, it is recommended that the tags be located within 6 to 12 inches of Tag Link. Those tags with ‘off body’ sensor must be placed on the front panel in the marked area. This will assure that the alarm TIC message is not transmitted. Tag Link Functions The following table lists the functions that are performed transparently in response to commands from the application software: COMMAND TAG LINK ACTION LED Power Up Powers up from sleep mode none Power Down Return to sleep mode immediately or after 30 seconds if no application command none Check RF Noise Measures and reports interference at 307 kHz Green Flashes Red Flashes Measures and reports interference at 433.92 MHz Test Tag TIF Interrogates tag and returns ID and tag status See next table Test Tag TIC Tag Link waits for TIC signal from specified tag See next table Set TLM Tag Link issues eLink TLM set command See next table Disable TLM Tag Link issues eLink TLM disable command See next table Check TLM Tag Link queries tag and reports rate to application See next table Assign MTAG Reads Mother Tag ID and assigns dynamic ID See next table MTAG Bond Sends baby tag ID(s) to Mother Tag, Mother Tag is then bonded to the assigned tag(s) See next table Each operation is performed for a maximum of 10 seconds. During application the following audio-visual signals are output: ACTION BEEPER Command received Very short beep Command succeeded Longer beep Command failed 4 short beeps Copyright 2003 - eXI Wireless Systems Inc. Page XX LED’s None random Both briefly on 980-000003 – 002. R1.01 User Manual - SUPERVISOR Restricted Rights eXI's commercial software and commercial computer software documentation is provided to United States Government agencies in accordance with the terms of this Agreement, and per subparagraph "(c)" of the "Commercial Computer Software - Restricted Rights" clause at FAR 52.227-19 (June 1987). For DOD agencies, the restrictions set forth in the "Technical Data-Commercial Items" clause at DFARS 252.227-7015 (Nov 1995) shall also apply. FCC Regulations This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for Class B Digital Device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures. • • • • Reorient or relocate the receiving antenna Increase the separation between the equipment and receiver Connect the equipment into an outlet on a circuit different from that to which the receiver is connected Consult the dealer or an experienced radio/TV technician for help Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. Model No.: Tag Link FCC ID: HE7TGL eXI Wireless Systems CANADA: 287710217261A * This device complies with Part 15 of the FCC Rules. Operation is subject to the following two rules: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation. Made in Canada Copyright 2003 - eXI Wireless Systems Inc. Page 137 980-000003 – 002. R1.01
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.4 Linearized : No Create Date : 2003:08:12 22:46:50Z Modify Date : 2003:08:28 15:16:54-07:00 Page Count : 3 Creation Date : 2003:08:12 22:46:50Z Mod Date : 2003:08:28 14:07:19-07:00 Producer : Acrobat Distiller 5.0 (Windows) Author : bruce Metadata Date : 2003:08:28 14:07:19-07:00 Creator : bruce Title : Microsoft Word - TAGLINK - user manual.docEXIF Metadata provided by EXIF.tools