Xplore Technologies of America HWNVWUNDP-1 Tablet PC with Wireless Wide Area Network Module User Manual Bradstreet SAR en US

Xplore Technologies Corp of America Tablet PC with Wireless Wide Area Network Module Bradstreet SAR en US

Contents

Regulatory Guide

Download: Xplore Technologies of America HWNVWUNDP-1 Tablet PC with Wireless Wide Area Network Module User Manual Bradstreet SAR en US
Mirror Download [FCC.gov]Xplore Technologies of America HWNVWUNDP-1 Tablet PC with Wireless Wide Area Network Module User Manual Bradstreet SAR en US
Document ID1105240
Application IDbiMcVmJNzc5Z56CS0226dA==
Document DescriptionRegulatory Guide
Short Term ConfidentialNo
Permanent ConfidentialNo
SupercedeNo
Document TypeUser Manual
Display FormatAdobe Acrobat PDF - pdf
Filesize39.13kB (489147 bits)
Date Submitted2009-05-04 00:00:00
Date Available2009-05-04 00:00:00
Creation Date2006-06-20 12:19:57
Producing SoftwareAcrobat Distiller 7.0.5 (Windows)
Document Lastmod2009-05-04 11:58:29
Document TitleBradstreet_SAR_en-US.fm
Document CreatorFrameMaker 7.2
Document Author: MPesch

English
Product safety information
Motion™ Tablet PCs and accessories are designed to optimize safety,
minimize strain, and withstand the rigors of portability. However, to
further reduce the risk of personal injury or damage to the unit, certain
precautions should be observed. The information in this document
applies to the Motion Computing J3400 Tablet PCs unless noted
otherwise.
Product mounting and installation disclaimer
Motion Computing shall not be liable under any theory of liability
(including, without limitation, contract, tort or statutory law) for any loss,
damage, personal injury, or other damage of any nature (including,
without limitation, direct, special, incidental or consequential damages)
arising directly or indirectly as a result of improper or inappropriate
placement, installation, or use of its products or any other application. In
order to safely install and use Motion products, full consideration of
occupants, systems (e.g., the location of fuel lines, navigation systems,
brake lines, electrical, drive train or other systems), air-bags and other
back-up, warning or safety equipment is required. Without limiting the
foregoing, Motion specifically disclaims any responsibility for the
placement, use or installation of its products not consistent with (i) the
original manufacturer’s or governmental or regulatory specifications and
recommendations for the environment where the products will be
placed, used or installed, (ii) Motion written product instruction sheets,
or (iii) workmanship standards.
English
Basic personal safety precautions
•
Do not attempt to service the Tablet PC or its components yourself.
Perform only those service installations for which Motion provides
instructions, such as swapping the battery, adding an external
battery, changing the hard disk drive (J3400 only), or changing
memory modules. For a list of serviceable accessories for this
product, see the Motion Web site at www.motioncomputing.com.
•
To avoid personal injury from electric shock or fire:
•
–
Completely power down the Tablet PC when replacing memory
modules, changing the hard disk drive, cleaning the Tablet PC,
its components, or chassis, or performing operations requiring
similar steps. To do this, first turn the power off at the power
switch, remove the battery, then disconnect the AC adapter
from the electrical outlet or from any other type of external
power source, such as an external battery.
–
Do not operate the Tablet PC near water, for example, near a
bathtub, kitchen sink or laundry tub, in a wet basement, by a
swimming pool, or in the rain. The cases, portfolios, and other
accessories currently offered by Motion are not designed to be
water resistant nor water tight. To see the list of accessories for
this product, visit the Motion Web site at
www.motioncomputing.com.
–
Do not connect or disconnect any cables or perform
maintenance or reconfiguration of this product during an
electrical storm.
–
Avoid using the wireless modem, wireless LAN, or wired LAN
during an electrical storm, as a remote risk of electric shock
from lightning exists.
–
Do not push foreign objects into air vents or other openings of
the Tablet PC or accessories, such as the PCA card slots or the
optical disk drive bays. Doing so can short out interior
components and may cause fire or electric shock.
–
When installing memory modules, ground yourself by touching
a grounded conductive surface, such as a device with a
grounded plug. Avoid touching the pins and leads on the
memory module or internal circuitry of the Tablet PC.
If the battery pack leaks and the fluid gets in your eyes, do not rub
them. Instead, rinse your eyes with clean running water and
English
immediately seek medical attention. Otherwise, eye injury may
result.
•
If the battery pack leaks and the fluid gets on your skin or clothing,
immediately wash it away with running water. Otherwise, skin
inflammation can occur.
Environmental
•
The extraction and use of natural resources are required in the
production of the equipment you purchased. The equipment may
contain hazardous substances that could impact health and the
environment if not disposed of using environmental disposal
systems available in your region.
•
To prevent the dissemination of those substances in our
environment and to diminish the impact on the natural resources,
we encourage you to use appropriate take-back environmental
disposal systems. Those disposal systems will reuse or recycle most
of the materials of your end-life equipment in compliance with
current environmental conventions.
•
The crossed-out wheeled bin symbol prompts you to use those
environmental disposal systems.
•
If you need more information about collection, disposal, reuse, and
recycling systems, please contact your local or regional waste
administration.
•
Also, you can contact Motion Computing, Inc. for more information
about the environmental processes for our products.
•
California Proposition 65 notice:
This product contains no known materials at levels which the State
of California has found to cause cancer, birth defects, or other
reproductive harm.
•
Directive 2002/95/EC of the European Parliament and of the Council
of January 2003 on the restriction of the use of certain hazardous
substances in electrical and electronic equipment (RoHS). All Motion
products are compliant to the RoHS directive.
•
Directive 2002/96/EC of the European Parliament and of the Council
of January 2003 on Waste Electrical and Electronic Equipment
(WEEE). All Motion products are compliant to the WEEE directive and
Motion assumes full responsibility for disposal takeback.
English
Setup precautions
•
When setting up the Tablet PC in the J-Series FlexDock, place it on a
level surface so it does not fall over and damage the unit, docking
station, keyboard, connectors, or other components.
•
When using the J3400 Tablet PC docked in the FlexDock, ensure that
foreign objects do not fall into the opening of the battery charging
bay located on the top of the FlexDock. Although there is no safety
risk to the user, foreign objects that have fallen into the battery
charging bay can cause damage to internal components and to
battery packs when battery packs are inserted into the battery
charging bay.
•
When you move the Tablet PC between environments with very
different humidity and/or temperature ranges, allow sufficient time
to adjust to the new humidity or temperature.
•
•
Do not drop the Tablet PC or subject it to other mechanical shocks.
•
See the Installation Instructions before connecting to the power
supply.
•
For important information about mounting and installation of
Tablet PCs, see “Product mounting and installation disclaimer” on
page 1.
Do not apply heavy pressure to the Tablet PC or subject it to strong
impact. Excessive pressure or impact can cause damage to Tablet PC
components or otherwise cause malfunctions.
Tablet PC precautions
•
Do not attempt to service the Tablet PC yourself, disassemble nor
modify it nor its components. You may damage the unit or its
components.
•
Operate the Tablet PC at the recommended temperature range of
+5oC to +35oC (+41oF to +95oF). Store it at a temperature of -20oC to
+60oC (+4oF to +140oF)
•
Certain environments may contain particles or debris that can
adhere to the Tablet PC display or to the Tablet PC pen tip. To avoid
damaging the display, clean it frequently with the cleaning cloth
provided or with a soft cloth. You may spray a window-type cleaner
or apply water to the cloth, but do not spray liquids directly on the
display.
•
Change pen tips regularly, especially if you work in an environment
that contains particles or debris. Dropping the pen onto a rough
English
surface may damage the pen tip or embed particles in it that can
damage the Tablet PC display. For instructions about changing the
pen tips, refer to the Motion Tablet PC User Guide found on the Tablet
PC or go to the Motion Web site at www.motioncomputing.com to
download the latest version of this Guide.
•
Store the pen in the pen bay of the Tablet PC. Carrying it in a pocket,
toolbox, or similar receptacle that contains particles or debris may
damage the pen tip or embed particles in it that can damage the
Tablet PC display.
•
Your J3400 Tablet PC ships with a battery bay cartridge (nonfunctioning) installed in the tablet. Do not discard the battery bay
cartridge. In the event your battery or spare battery becomes
damaged and is being replaced by the manufacturer, you will need
the battery bay cartridge to insert into the battery bay to prevent
foreign objects falling into the battery bay.
•
For audio sound pressure statements, see “Comfort and health” on
page 10.
Tablet PC disposal
•
•
Do not dispose of the unit in general waste.
‘If you are unable to locate a disposal site, contact your reseller or
Motion Computing.
High risk and dangerous activity warning
•
This computer system is not intended to be used as a medical device
or for use in high-risk or dangerous activities, including without
limitation, the operation of nuclear facilities, aircraft navigation or
communications systems, hospital or medical operations, air traffic
control machines, treating, diagnosing, or monitoring patients, or
for any other uses where the failure of the computer system could
lead to death, personal injury, or severe environmental damage.
Cabling and power cord precautions
•
Power cord sets for use in other countries must meet the
requirements of that country. Use the appropriate AC power cord for
your locale. For information about power cord set requirements,
English
contact the Motion Reseller from whom you purchased the product,
or contact Motion Computing if you purchased the product from us.
•
If no power cord was provided for your Tablet PC or for an accessory,
purchase a power cord that is approved for use in your country and
that matches the required voltage / amperage rating of the Tablet
PC.
•
If you use an extension cord with your AC adapter, ensure that the
total ampere rating of the products plugged into the extension cord
does not exceed the ampere rating of the extension cable.
•
When using your power cord, make sure to position it around
objects so it will not be cut or punctured.
Power adapter precautions
•
Use only the AC adapter and power cord approved for this Tablet PC
or Tablet PC accessory. Use of another type of AC adapter may risk
fire or explosion.
•
Place the AC adapter in a ventilated area, such as on a desktop or the
floor, when you use it to run the Tablet PC or to charge the battery.
Do not cover the AC adapter with papers or other items that will
reduce cooling; also, do not use the AC adapter while it is inside a
carrying case.
•
Be sure that nothing rests on the AC adapter's power cable and that
the cable is not located where it can be tripped over or stepped on.
•
Disconnect power cords and cables by grasping the connector, not
by pulling on the cable itself. As you pull out the connector, keep it
evenly aligned to avoid bending any connector pins. Before you
connect a cable, make sure both connectors are correctly aligned.
Battery pack warnings and precautions
•
The Tablet PC contains an internal lithium ion (Li-ion) battery pack.
Replace the internal battery pack only with a Motion battery or a
Motion-recommended equivalent to avoid the risk of fire or
explosion resulting in personal injury.
•
Do not use the battery pack in combination with other types of
battery packs (such as dry-cell battery packs), except for an J3400
additional battery available from Motion Computing, or battery
packs with different capacities or brands. This can result in it being
over-discharged during use or overcharged during recharging,
English
possibly causing it to leak, overheat, emit smoke, burst and/or
ignite.
•
Do not dispose of batteries in a fire. They may explode. Dispose of
used batteries according to the manufacturer's instructions. The
label on the battery lists the manufacturer’s name. See the section
“Battery pack disposal” on page 9 for more information about
battery disposal.
•
Do not use or leave the battery pack near a heat source. Heat can
melt the insulation and damage other safety features, possibly
causing it to leak, overheat, emit smoke, burst and/or ignite.
•
Do not immerse the battery pack in water nor allow it to get wet. Its
protective features can be damaged; it can be charged with
extremely high current and voltage, and abnormal chemical
reactions may occur, possibly causing it to leak, overheat, emit
smoke, burst and/or ignite.
•
Do not disassemble or modify the battery pack. If disassembled, the
battery pack can leak, overheat, emit smoke, burst and/or ignite.
•
Do not connect the positive (+) and negative (-) terminals with a
metal object such as wire. Short-circuiting may occur causing the
battery pack to leak, overheat, emit smoke, burst and/or ignite.
•
Do not pierce the battery pack with a sharp object, strike it with a
hammer, step on it, or throw it. These actions can damage or deform
it, internal short-circuiting can occur, possibly causing it to leak,
overheat, emit smoke, burst and/or ignite.
•
Do not use an apparently deformed or damaged battery pack,
which may leak, overheat, emit smoke, burst and/or ignite.
•
Do not directly solder the battery pack. Heat can melt the insulation
and damage other safety features, possibly causing it to leak,
overheat, emit smoke, burst and/or ignite.
•
Store the battery pack in a location where children cannot reach it.
Make sure children do not remove the battery pack from the Tablet
PC or charger.
•
If the battery pack leaks, gives off a bad odor, generates heat,
becomes discolored or deformed, or in any way appears abnormal
during use, recharging or storage, immediately remove it from the
Tablet PC or charger and stop using it, If this is discovered when you
first use the battery, return it to your Motion reseller or to Motion
Computing, if you bought it directly from us.
•
Do not transport the lithium ion batteries used in your Tablet PC in
checked baggage. You may take up to two spare batteries in carry-on
English
luggage in addition to the one in your Tablet PC. Transporting
batteries in checked baggage or transporting more than two spare
batteries in carry-on baggage violates transportation law.
Remember to remove batteries from the battery charger before
transporting it in carry-on or checked baggage.
•
Your J3400 Tablet PC ships with a battery bay cartridge (nonfunctioning) installed in the tablet. Do not discard the battery bay
cartridge. In the event your battery or spare battery becomes
damaged and is being replaced by the manufacturer, you will need
the battery bay cartridge to insert into the battery bay to prevent
foreign objects falling into the battery bay.
Battery charger precautions
•
Read the documentation supplied with the battery charger. This
provides information about charging and precautions for use.
•
Use only a Motion battery charger to recharge the batteries. It is
specifically designed for that purpose. Charging with a non-Motion
battery charger can result in extremely high current and voltage,
abnormal chemical reactions may occur, possibly causing it to leak,
overheat, emit smoke, burst and/or ignite.
•
Battery charging temperature: The ambient temperature of the
battery being charged should range from 0º C to +40º C (+32º F to
+104º F). Charging the battery outside this range may harm battery
performance or reduce battery life.
•
Do not recharge the battery pack near fire or in extremely hot
weather. Hot temperatures can inhibit recharging or can damage its
built-in protective features. Heat can possibly lead to leakage,
overheating, smoking, bursting and/or igniting.
•
If you transport the battery charger in checked baggage, be sure to
remove the batteries from the charger before packing it.
•
When using the J3400 Tablet PC docked in the FlexDock, ensure that
foreign objects do not fall into the opening of the battery charging
bay located on the top of the FlexDock. Although there is no safety
risk to the user, foreign objects that have fallen into the battery
charging bay can cause damage to internal components and to
battery packs when battery packs are inserted into the battery
charging bay.
English
Battery pack disposal
•
Dispose of the lithium ion battery packs only at approved disposal
sites. To locate an appropriate site, contact the solid waste disposal
officials where you live or look for a rechargeable battery recycling
Web site that lists disposal locations near you.
•
Do not dispose of battery packs in a fire, throw them in a trash
receptacle, put them in a recycling bin not intended for their
disposal, or otherwise discard them in a manner that may result in
their being hazardous to the environment.
Travel precautions
•
For information about transporting batteries, see “Battery Warnings
and Precautions” in this document.
•
When traveling, do not store the Tablet PC in an overhead
compartment or other area where it could slide around, nor check it
in your baggage.
•
Do not put the Tablet PC through a metal detector. You can safely
put it through an X-ray security machine without harming any
components.
•
Be sure to charge the battery before you hand check the Tablet PC.
You may be asked to turn the Tablet PC on at a baggage check point.
•
Ensure that your Tablet PC is configured for air travel prior to
boarding the airplane.
Component replacement precautions
•
Install and use only components sold by Motion Computing in/with
your Tablet PC. Installation or use of non-Motion components may
damage the Tablet PC and/or its components and void the warranty.
•
Components currently available from Motion Computing as user
replaceable parts include an AC power adapter (rated for general
use), memory modules, and an additional battery pack. These
components may change periodically. Contact Motion Computing
for more information or if you have questions about replacing a
specific component.
•
Do not replace nor attempt to service internal Tablet PC
components such as the hard disk drive, Bluetooth card, antennas,
fingerprint module components, etc. Such actions can damage the
Tablet PC and/or its components and void the warranty.
English
Wireless Mini PCI-Express devices
While Motion sells and may recommend certain wireless Mini PCIExpress devices for the Tablet PC, these should only be installed by
Motion or a qualified Motion reseller. Contact Motion Computing or your
authorized Motion reseller for information about Motion-recommended
wireless Mini PCI-Express devices.
Accessory precautions
•
Please read the instructions packaged with your accessories
carefully before setting up or operating them. The Motion accessory
you purchase may include documentation about safety,
precautions, and warnings needed to set up or operate the
accessory. This accessory documentation provides specific
information about functionality, usage limitations, user
serviceability, battery or component disposal, handling precautions,
or electrostatic discharge, etc. for the product.
•
The cases, portfolios, and other accessories currently offered by
Motion are not designed to be water resistant nor water tight. Visit
the Motion Web site to see the most current list of accessories.
Recommended third-party accessories
•
Use only Motion-recommended third-party accessories with a
Motion Tablet PC.
•
If you choose to use a non-Motion-recommended third-party
accessory, it is at your own risk and may damage the Tablet PC and/
or its components and the accessory device and void the warranty.
•
The use of third-party accessories not approved or recommended
by Motion may cause the product to lose the class compliance for
which it was certified.
Comfort and health
HEALTH WARNING: Keyboard use or use of a pointing device may be
linked to serious injuries or disorders. For further information, visit the
Mayo Clinic Web site at www.mayoclinic.org.
10
English
You may help prevent occasional discomfort in your hands, arms,
shoulders, neck, and other parts of your body by:
•
•
Taking frequent breaks to stretch and change your working position.
•
Using the touch pad on a keyboard or the Tablet PC pen, which
change the way you use your hands and wrists; this provides a break
from the keyboard keys or mouse.
•
Excessive sound pressure from earphones or headphones can cause
hearing damage and hearing loss. Adjustments of the volume
control or equalizer to settings other than the default setting can
increase earphone and headphone output voltage and therefore
increase the volume and sound pressure levels to levels above the
healthy range.
Resting your hands and wrists frequently so they have time to
recover from repetitive movements. Use a wrist pad.
If these symptoms persist or continue to occur and include pain,
throbbing, aching, tingling, numbness, burning sensations, or stiffness,
DO NOT IGNORE THESE WARNING SIGNS. PROMPTLY SEE A QUALIFIED
HEALTH PROFESSIONAL.
Regulatory and safety compliance
The following sections describe regulatory and safety compliance by
country and by region.
Note: To determine what regulatory and safety marks apply to a specific
product, component, or accessory, check the product label affixed to the
product or its component.
Federal Communications Commission notice (USA)
Electromagnetic Interference (EMI) is any
electromagnetic disturbance that interrupts, obstructs, or
otherwise degrades or limits the effective performance of
electronics or electrical equipment. These emissions can
potentially disrupt, degrade, or otherwise interfere with
authorized electronic emissions, which may include
television, AM/FM broadcasts, cellular services, radar, airtraffic control, and pagers.
English
11
The FCC Rules and Regulations have established Radio Frequency (RF)
emission limits to provide an interference-free RF spectrum. Many
electronic devices, including computers, generate RF energy incidental
to their intended function and are, therefore, covered by these rules.
Your Motion Tablet PC system, Motion J-Series FlexDock, Motion J-Series
Mobile Keyboard, and all accessories have been designed and found to
meet the regulatory agency limits for Electromagnetic Compatibility
(EMC). EMC is the ability of electronic devices, including computers, to
function properly together in the electronic environment. However,
there is no guarantee that in a specific installation it will not cause
interference. Should this equipment cause harmful interference to radio
or television reception, which can be determined by turning the
equipment off and on, you are encouraged to try to correct the
interference by one or more of the following measures:
•
•
•
•
Reorient the receiving antenna.
Relocate the Tablet PC and the receiver.
Separate the Tablet PC and the receiver.
Plug the Tablet PC and receiver into different circuits.
You may also need to contact a radio/television technician for assistance.
Unintentional Emitter per FCC Part 15
The rating label on Motion Tablet PCs, Motion J-Series FlexDock, Motion
J-Series Mobile Keyboard, and all accessories show which class (A or B)
these devices fall into. Class B devices have an FCC logo (shown here) or
FCC ID on the label. Class A devices do not have an FCC ID on the label.
Once you determine the class of the device, refer to the following
corresponding statement and to the FCC notices in this document.
•
•
Class A is for business or industrial environments.
Class B is for residential environments.
This device complies with Part 15 of the Federal Communications
Commission (FCC) Rules. Operation is subject to the following two
conditions:
•
•
12
This device may not cause harmful interference.
This device must accept any interference received, including
interference that may cause undesired operation.
English
Class A Equipment: This equipment has been tested and found to
comply with the limits for a Class A digital device, pursuant to part 15 of
the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference when the equipment is
operated in a residential environment. This equipment generates, uses,
and can radiate radio frequency energy and, if not installed and used in
accordance with the manufacturer’s instruction manual, may cause
interference with radio communications. Operation of this equipment in
a residential area is likely to cause harmful interference, in which case
you will be required to correct the interference at your own expense.
Class B Equipment: This equipment has been tested and found to
comply with the limits for a Class B digital device, pursuant to part 15 of
the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference when the equipment is
operated in a residential environment. This equipment generates, uses,
and can radiate radio frequency energy and, if not installed and used in
accordance with the manufacturer’s instruction manual, may cause
interference with radio communications. However, there is no guarantee
that interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and
on, you are encouraged to try to correct the interference by one or more
of the following measures:
•
•
•
Reorient or relocate the receiving antenna
•
Consult the dealer or an experienced radio/television technician for
help
Increase the separation between the equipment and the receiver
Connect the equipment into an outlet on a circuit different from
that to which the receiver is connected
The following information is provided on the device or devices covered
in this document in compliance with FCC regulations:
Model number: T008 (Motion J3400 Tablet PC)
Company name: Motion Computing, Inc.
8601 RR 2222 Building II
Austin, Texas 78730
512-637-1100
English
13
Technical standards
The Tablet PC meets the following technical standards:
€
€
€
€
€
€
€
FCC Part 15 B Class B
FCC Part 22 (WWAN)
FCC Part 24 (WWAN)
OET 65 Supplement C
UL 60950-1
Intentional Emitter per FCC Part 15
Embedded in your Tablet PC are various Radio Frequency (RF) wireless
communication devices. It may contain one or more radio type devices
that operate in the following bands:
€
€
€
€
€
450-1550 KHz band
824-960 MHz band
1710-2170 GHz band
All Radio type devices embedded in your Tablet PC have met all the
qualifications for use under FCC regulations and guidelines.
This equipment complies with FCC Radio Frequency Electromagnetic
Signal (RF) exposure limits set forth for an uncontrolled environment of
portable transmission. This product has been evaluated for RF exposure
at a distance of 20 cm (8 inches). Operation at a separation distance less
than 20 cm (8 inches) from the radiating element to nearby persons will
not expose nearby persons to RF levels that exceed the FCC rules for RF
exposure.
Operation of this wireless communication device is subject to the
following two conditions:
€
€
14
This device may not cause harmful interference
This device must accept any interference received, including
interference that may cause undesired operation.
English
FCC CAUTION: Any changes or modification not expressly approved by
the party responsible for compliance could void the user•s authority to
operate this equipment.
FCC Radiation Exposure Statement:
€
€
This equipment complies with FCC radiation exposure limits set
forth for an uncontrolled environment.
. This equipment contains an internal antenna transmitter whose effective use
may be affected if it is co-located or operating in conjunction with any
other antenna or transmitter.
€
This equipment complies with FCC Radio Frequency
Electromagnetic Signal (RF) exposure limits set forth for an
uncontrolled environment of portable transmission. This product
has been evaluated for RF exposure at a distance of 20 cm (8 inches).
Operation at a separation distance less than 20 cm (8 inches) from
the radiating element to nearby persons will not expose nearby
persons to RF levels that exceed the FCC rules for RF exposure.
€
For the measured Specific Absorption Rate (SAR) limits for the J3400
tablet, refer to the table •Measured Specific Absorption Rates (SAR)
for J3400 tabletŽon page 16.
WARNING: Do not attempt to service the wireless communication
device built into the Tablet PC yourself. Such action may void the
warranty on the Tablet PC. Contact your Motion Reseller or Motion
Computing for information about servicing your wireless
communication device.
English
15
Measu red Specif ic Absorption R ates (SAR) for J3400 tablet
Frequency
Ba nd
Mode
Broadband
Broadband
824-960
MHz
Repor ted
SAR L evel
SAR
Cate gory
Is less than the
maximum level Mobile/
Portable
permitted.
North
American
SAR Limit
1.6 W/kg
Euro pean
SAR Limit
2.0 W/kg
Is less than the
Broadband 1710-2170 maximum level Mobile/
Broadband MHz
Portable
permitted.
1.6 W/kg
2.0 W/kg
Note: The Radio Frequency (RF) emitter installed in your Tablet PC must
not be located or operated in conjunction with any other antenna or
transmitter.
16
English
J3400
Internal radio(s) may have an individual FCC Identifier which does not
apply to this configuration. Only the FCC ID (Identifier) shown on the
label(s) located inside the battery bay of the J3400 (Model: T008) Tablet
PC is applicable to this internal radio configuration. The J3400 (Model:
T008) Tablet PC must not be co-located or operating in conjunction with
any other antenna or transmitter than specified in the certification of the
FCC Identifier(s) shown on the label.
Modifications
Any changes or modification not expressly approved by the party
responsible for compliance could void the user•s authority to operate
this equipment. The FCC requires that you be notified that any changes
or modifications made to this device that are not expressly approved by
Motion Computing, Inc. may void your authority to operate the
equipment.
Cables
Connections to this Tablet PC must be made only with shielded cables.
This reduces possible interference with radio communications and
complies with FCC Rules and Regulations for this EMC classification.
Airline travel notice
The FAA requires that you suspend wireless operations before
boarding an airplane. These include both internal and external
wireless devices. Internal wireless connections are indicated by
the wireless LED on the Tablet PC front panel (identified by the
wireless icon shown here). If the LED is ON or blinking, the
wireless connection is enabled. External wireless devices may be
installed in the PC Card slot or attached to the Tablet PC and
must also be disabled. For information about disabling these devices,
see IMPORTANT below.
English
17
To disable external wireless devices installed in the Tablet PC ExpressCard
slot or attached to the Tablet PC, eject the card or unplug the external
device. To disable external devices via the software, see the instructions
that came with the device or contact the device manufacturer.
IC notice (Canada only)
Unintentional Emitter per ICES-003
Motion Computing Tablet PCs are
classified by the Industry Canada
(IC) Interference-causing
Equipment Standard #3 (ICES-003) Issue 3 as a Class B digital device. This
classification is located on the label on the bottom of your Tablet PC.
Canada ICES-003, Class/Classe B
The Tablet PC meets the following technical standards:
€
€
€
€
€
€
IEES-005 Class B
RSS-102
RSS-132
RSS-133
CSA CAN C22.2 No. 60950-1
Look for a statement on the label similar to the following:
Canada ICES-003, Class/Classe B
This Class B (or Class A, if so indicated on the registration label) digital
apparatus meets the requirements of the Canadian Interference-Causing
Equipment Regulations.
Cet appareil numérique de la Classe B (ou Classe A, si ainsi indiqué sur
l•étiquette d•enregistration) respecte toutes les exigences du Règlement
sur le Matériel Brouilleur du Canada.
18
English
Intentional Emitter per RSS 210
Embedded in your Tablet PC are various Radio Frequency (RF) wireless
communication devices. It may contain one or more radio type devices
that operate in the following bands:
€
€
€
€
€
450-1550 KHz band
824-960 MHz band
1710-2170 GHz band
All Radio type devices embedded in your Tablet PC have met all the
qualifications for use under IC regulations and guidelines.
All Radio type devices embedded in your Tablet PC comply with the RSS
210 and RSS-102 standards of the Industry Canada. Operation is subject
to the following two conditions: (1) this device may not cause
interference, and (2) this device must accept any interference, including
interference that may cause undesired operation of this device.
The term •ICŽbefore the equipment certification number only signifies
that the Industry Canada technical specifications were met.
This equipment complies with Industry Canada Radio Frequency
Electromagnetic Signal (RF) exposure limits set forth for an uncontrolled
environment of portable transmission.
L•utilisation de ce dispositif est autorisée seulement aux conditions
suivantes: (1) il ne doit pas produire de brouillage et (2) l•utilsateur du
dispositif doit éntre prét a accepter tout brouillage radioélectrique recu,
meme si ce brouillage est susceptible de compromettre le
fonctionnement du dispositif.
English
19
Conformité Européenne (CE) (European Union)
Unintentional Emitter
The (Conformité Européenne) symbol found on the Tablet PC
indicates compliance to the EMC Directive and the Low
Voltage Directive of the European Union. This means that the
Tablet PC meets the following technical standards:
20
•
EN 55011 (CISPR 11) — Limits and Methods of Measurement of
Radio Interference Characteristics of Industrial, Scientific, And
Medical (ISM) Radio Frequency Equipment
•
EN 55022 (CISPR22) — Limits and Methods of Measurement of Radio
Interference Characteristics of Information Technology Equipment
•
EN 55024 (IEC 61000 4-2, 4-3, 4-3, 4-5, 4-6, 4-8, 4-11) — Information
Technology Equipment-Immunity Characteristics - Limits and
Methods of Measurement
•
BS EN 50332-2 — Sound system equipment. Headphones/
earphones associated with portable audio equipment maximum
sound pressure level measurement methodology and limit
considerations; matching of sets with headphones if either or both
are offered separately.
•
EN 61000 3-2 (IEC 61000 3-2) — Electromagnetic compatibility
(EMC) - Part 3: Limits - Section 2: Limitations for harmonic current
emissions (Equipment input current up to and including 16 A per
phase)
•
EN 61000 3-3 (IEC 61000 3-3) — Electromagnetic compatibility
(EMC) - Part 3: Limits - Section 3: Limitations of voltage fluctuations
and flicker in low-voltage supply systems for equipment with rated
current up to and including 16 A
•
EN60950-1 — Safety of Information Technology Equipment
English
Intentional Emitter
The CE mark shown here is a device ID that
means the product complies with the
essential requirements of the R&TTE
Directive 1999/5/EC with essential test suites.
XXXX
Embedded in your Tablet PC are various Radio Frequency (RF) wireless
communication devices. It may contain one or more radio type devices
that operate in the following bands:
€
€
€
€
€
450-1550 KHz band
824-960 MHz band
1710-2170 GHz band
All Radio type devices embedded in your Tablet PC have met all the
qualifications for use under IC regulations and guidelines and comply
with the following standards:
€
€
€
€
€
€
€
IEC/EN 60950-1 „ Safety of Information Technology Equipment
ETSI EN 300-826 „ General EMC requirements for radio equipment
ETSI EN 301-489 „ Electromagnetic compatibility of (EMC) standard
for radio equipment and services
ETSI EN 50371 „ Basic standard for the measurement of Specific
Absorption Rate related to human exposure to electromagnetic
fields.
ETSI EN 301-511 „ Harmonized EN for Mobile Stations in the GSM
900 and GSM 1800 Bands Covering Essential Requirements Under
Article 3.2 of the R&TTE Directive (1999/5/EC).
ETSI EN 301-908-1 „ Electromagnetic compatibility and Radio
spectrum Matters (ERM); Base Stations (BS), Repeaters and User
Equipment (UE) for IMT-2000 Third-Generation cellular networks;
Part 1: Harmonized EN for IMT-2000, introduction and common
€
English
21
requirements, covering essential requirements of article 3.2 of the
R&TTE Directive.
22
€
EN 301-489-7 „ Electromagnetic Compatibility and Radio Spectrum
Matters (ERM); Electromagnetic Compatibility (EMC) Standard for
Radio Equipment and Services; Part 7: Specific Conditions for Mobile
and Portable Radio and Ancillary Equipment of Digital Cellular Radio
Telecommunications Systems (GSM and DCS).
€
EN 301-489-24 „ Electromagnetic Compatibility and Radio
Spectrum Matters (ERM); Electromagnetic Compatibility (EMC)
Standard for Radio Equipment and Services; Part 24: Specific
Conditions for IMT-2000 CDMA Direct Spread (UTRA) for Mobile and
Portable (UE) Radio and Ancillary Equipment.
English
English
23
Wideband transmission system radio
The Wideband Transmission System Radio in your Tablet PC contains a
custom antenna that complies with the following directives:
English
Deutsch
Français
Hereby, Motion Computing, Inc., declares that this
Wideband Transmission System Radio is in compliance with
the essential requirements and other relevant provisions of
Directive 1999/5/EC and the WIFI ALLIANCE®.
Hiermit erklärt Motion Computing, Inc., dass sich dieser/
diese/dieses Wideband Transmission System Radio in
Übereinstimmung mit den grundlegenden Anforderungen
und den anderen relevanten Vorschriften der Richtlinie
1999/5/EG befindet.
Hiermit erklärt Motion Computing, Inc. die
Übereinstimmung des Gerätes Wideband Data
Transmission System Radio mit den grundlegenden
Anforderungen und den anderen relevanten Festlegungen
der Richtlinie 1999/5/EG.
Par la présente Motion Computing, Inc. déclare que
l'appareil Wideband Data Transmission System Radio est
conforme aux exigences essentielles et aux autres
dispositions pertinentes de la directive 1999/5/CE.
Par la présente, Motion Computing, Inc. déclare que ce
Wideband Data Transmission System Radio est conforme
aux exigences essentielles et aux autres dispositions de la
directive 1999/5/CE qui lui sont applicables.
Other notices and marks
Sound pressure/volume notice
Excessive sound pressure from earphones or headphones can cause
hearing damage and hearing loss. Adjustments of the volume control or
equalizer to settings other than the default setting can increase
earphone and headphone output voltage and therefore increase the
volume and sound pressure levels to levels above the healthy range.
24
English
Battery notice
Motion Computing sealed lithium ion batteries comply with all
applicable shipping regulations as prescribed by industry and legal
standards. This includes compliance with the UN Recommendations on
the Transport of Dangerous Goods; IATA (International Air Transport
Agency) Dangerous Goods Regulations, 44th Edition, 2003, Special
Provisions A45, and applicable U.S. DOT regulations for the safe
transport of lithium ion batteries. Each Motion Computing cell or battery
has been tested under provisions of the UN Manual of Tests and Criteria,
Part III, Sub-section 38.3. Complies with Battery Directive 2006/66/EC.
Laser safety notice
For safety and regulatory information about third-party products that
may contain Class 1 laser equipment, see the documentation shipped
with the product.
Motion CD-ROM and DVD/CD-RW drives are Class 1 laser products. A
Class 1 laser is considered to be incapable of producing damaging
radiation levels and is therefore determined to be eye safe. These lasers
are exempt from most control measures. Many lasers in this class are
lasers which are embedded in an enclosure that prohibits or limits access
to the laser radiation. However, we recommend that you do not stare
into the beam or view it directly with optical instruments.
Wireless notices
In some environments, the use of wireless devices may be restricted.
Such restrictions may apply aboard airplanes, in hospitals, near
explosives, in hazardous locations, etc. If you are uncertain of the policy
that applies to the use of this device, please ask for authorization to use it
prior to turning it on. For instructions for disabling internal and external
wireless devices, see the section “Airline Travel Notice” in this document.
Saudi Arabian Quality Mark
All Motion Tablet PCs and Motion Tablet PC systems meet the Quality
Mark standards issued by the Saudi Arabian Standards Organization
(SASO) in Articles 3 and 12 in Royal Decree No. M/10 dated
1392(H)-03-03.
English
25
Australia Radio Communications (C-Tick) Statement
All Motion Tablet PCs and Motion Tablet PC systems meet
the safety and technical standards set by Australian
Communications and Media Authority (ACMA) and can be
safely connected to the wireless network.
The Tablet PC meets the following technical standards:
•
•
•
•
•
•
AS/NZS 4251
AS/NZS CISPR22
AS/NZS 60950-1
AS/NZS S042.1
AS/NZS S042.3
AS/NZS 4268
Internal Bluetooth module notice
Class B Equipment: This equipment has been tested and found to
comply with the limits for a Class B digital device, pursuant to the
Australian Communications and Media Authority Rules. These limits are
designed to provide reasonable protection against harmful interference
when the equipment is operated in a residential environment. This
equipment generates, uses, and can radiate radio frequency energy and,
if not installed and used in accordance with the manufacturer’s
instruction manual, may cause interference with radio communications.
However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference
to radio or television reception, which can be determined by turning the
equipment off and on, you are encouraged to try to correct the
interference by one or more of the following measures:
26
•
•
•
Reorient or relocate the receiving antenna
•
Consult the dealer or an experienced radio/television technician for
help
Increase the separation between the equipment and the receiver
Connect the equipment into an outlet on a circuit different from
that to which the receiver is connected
English
This device complies with all the essential Australian and New Zealand
Rules for Information Technology Equipment. Operation is subject to the
following two conditions:
€
€
This device may not cause harmful interference
This device must accept any interference received, including
interference that may cause undesired operation
Sound pressure/volume notice
Excessive sound pressure from earphones or headphones can cause
hearing damage and hearing loss. Adjustments of the volume control or
equalizer to settings other than the default setting can increase
earphone and headphone output voltage and therefore increase the
volume and sound pressure levels to levels above the healthy range.
Radio frequency wireless communication devices
Embedded in your Tablet PC are various Radio Frequency (RF) wireless
communication devices. It may contain one or more radio type devices
that operate in the following bands:
€
€
€
€
€
450-1550 KHz band
824-960 MHz band
1710-2170 GHz band
All radio type devices embedded in your Tablet PC have met all the
qualifications for use under IC regulations and guidelines.
English
27
28
English

Source Exif Data:
File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.4
Linearized                      : No
Create Date                     : 2006:06:20 12:19:57Z
Modify Date                     : 2009:05:04 11:58:29-05:00
Page Mode                       : UseOutlines
Producer                        : Acrobat Distiller 7.0.5 (Windows)
Mod Date                        : 2009:05:04 11:58:29-05:00
Creation Date                   : 2006:06:20 12:19:57Z
Author                          : MPesch
Creator Tool                    : FrameMaker 7.2
Metadata Date                   : 2009:05:04 11:58:29-05:00
Document ID                     : uuid:5215104d-6058-4b93-ae7f-8307c0266c85
Instance ID                     : uuid:c6f432d1-f4cf-41b6-b3bc-42501959b9a2
Format                          : application/pdf
Title                           : Bradstreet_SAR_en-US.fm
Creator                         : MPesch
Page Count                      : 28
EXIF Metadata provided by EXIF.tools
FCC ID Filing: Q3QHWNVWUNDP-1

Navigation menu