Xuzhou Fly Dream Electronic Science and Techonology F6TB 2.4G transmitter system User Manual F6TA Manual v3 2

Download:
Mirror Download [FCC.gov]
Document ID	1923338
Application ID	XV+Jcv286CtUelgGZu2X0g==
Document Description	User Manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	135.6kB (1695030 bits)
Date Submitted	2013-03-22 00:00:00
Date Available	2013-03-22 00:00:00
Creation Date	2013-03-19 14:50:42
Producing Software	Acrobat Distiller 7.0 (Windows)
Document Lastmod	2013-03-21 15:29:17
Document Title	F6TA Manual v3.2.pdf
Document Creator	PScript5.dll Version 5.2
Document Author:	Administrator

F6TB Manual
2.4G transmitter system
www.fd-rc.com
Contents
1 Preface……………………………………………………………………………3
1.1 Important statement………………………………………………………3
1.2 Safety notice………………………………………………………………3
1.3 Attention before flight………………………………………………3
2 Item specification and features………………………………………………4
2.1 Packing list………………………………………………………………4
2.2 Transmitter F6TB………………………………………………………4
2.3 Receiver IS-6R…………………………………………………………4
3 Operation panel………………………………………………………………………5
3.1 Front of F6TB……………………………………………………………5
3.2 Back of F6TB……………………………………………………………5
4 System manual…………………………………………………………………………6
4.1 Model choice………………………………………………………………6
4.2 Channel reverse……………………………………………………………6
4.3 D/R setting………………………………………………………………7
4.4 Power supply setting……………………………………………………8
4.5 Bind setting………………………………………………………………8
5 S enio r menu… … …… … …… … … …… … …… … …… …… …… … … …… … …… ..9
5 . 1 T i m e r s e t t i n g … … … … … … … … … … … … … … … … … … … … … … … … ..9
5 . 2 T r a n s m i t t i n g p o w e r s e t t i n g … … … … … … … … … … … … … … … ..9
6 Mode choices……………………………………………………………………10
6.1 Hand type choice…………………………………………………………10
6.2 Country and area choice………………………………………………11
Failsafe…………………………………………………………………………11
8 Simulator
FLY-DREAM
mode…………………………………………………………………11
WWW.FD-RC.COM
1 Preface
1.1 Important statement
1) The transmitter is suitable for experienced pilots beyond 14 years old.
2) Flying the model aircraft in approved ground is a must.
3) We are not responsible any safety caused by operation, usage or control once the
transmitter is sold out.
4) We consign our distributors to offer technical support and service after sale. Please contact
the local distributors for problem solutions cause by usage, operation, maintenance, etc.
1.2 Safety notice
1) Far away from obstacle and people
RC aircraft in flights is uncertain of flight speed and status, which potential risk exists in when
flying. Please keep your radio controlled aircraft far away from people, high buildings,
high-tension line, etc, and avoid operating in rain, storms, thunder and lightening.
2) Far away from humidity environment
Radio system should be kept away from humidity and vapor because it is composed of
complicated precise electronic elements and mechanical parts.
3) Proper operation
Use original spare parts to upgrade, modify or maintain your equipment in order to assure its
safety. Please operate your equipment within the range of functions permitted. It is forbidden to
use out of the safety laws or regulations.
4) Safety operation
Operate your equipment according to your body status and flight skills. Fatigue, listlessness and
misoperation will increase the possibilities of accidental hazard.
5) Far away from heat sources
The inside of the transmitter is composed of precise electronic components and mechanical
parts. Keep it far away from heat sources and sunshine to avoid distortion, or even damage
caused by high temperature and Max. operation temperation: +55 degree
6) Supply power correct
Please read the voltage range of transmitter and receiver from the manual, don’t use the voltage
beyond the range to supply power to transmitter and receiver.
1.3
Attention before flight
1) Ensure the battery packs of both transmitter and receiver are fully saturated.
2) Please ensure that the transmitter and receiver binding success, and the receiver has been
set up in accordance with the failsafe.
3) Ensure both the throttle stick and the throttle trim of your F6TB stay at the lowest positions
before operation.
4) When starting your flight, turn on your F6TB first, and connect the battery to the aircraft last.
When turning off the aircraft, disconnect the battery first, and turn off your F6TB last.
5) Ensure whether the directions and actions of all the servos in your RC aircraft are correct
when executing commands of the transmitter. Using broken servos will result in unforeseen
dangers.
FLY-DREAM
WWW.FD-RC.COM
User
manual
2 Item specification and features
Transmitter
2.1 Packing list
2.2 Transmitter F6TB
Channel
Frequency range
Spread Spectrum
1-20CH
2.404GHz- 2.480GHz Rated voltage
FHSS
Operating current
6.0V
”P$
1) The first choice transmitter for fixed wing plane.
2) To break the traditional, realize a second to switch from left to right quickly
3) Perfect design accord with human body engineering, the unique handle design, hold it
more comfortable.
4) Antenna is stretchable, easy to carry and convenient to packing
5) Clear and legibility of the code screen, easy and convenient to debug
6) The system adopts 2.4G FHSS, compatible with FLY-DREAM V3 system.
7) High frequency output power can be adjusted, more humanized and more environmental
protection
8) Save eight of fixed wing plane.
9) Digital electronic trim, position display, electronic voice prompt.
FLY-DREAM
WWW.FD-RC.COM
3 Operation panel
3.1 Front of F6TB
3.2 Back of F6TB
FLY-DREAM
WWW.FD-RC.COM
4 System menu
4.1 Model choice
Press the button of “Enter” and gets into model choice interface, screen will display as:
You can change the model No. by “UP” and “down”, and gets into channel reverse interface.
Press “Exit” button exit setting.
U-32 display on the screen is the version of transmitter
V3.2.
4.2 Channel reverse
Press “ENTER” and gets into “channel reverse setting” interface, screen display as :
Press “DOWN”
Press “UP”
Change channel by press “DOWN”, press “UP” change channel reverse setting.Please save the
setting after confirm, and gets into “Dual rate setting”. Press “EXIT” to exit the setting.
FLY-DREAM
WWW.FD-RC.COM
4.3 D/R setting
Press the button “ENTER” gets into “D/R setting” interface, csreen will display as :
Press “UP” or
“DOWN”
Press “EXIT”
Press ”EXIT” button to change the channel No., Press ”UP” or ”DOWN” change rudder value.Aft
er confirm press ”ENTER” button save setting, and enter ”D/R setting”interface.
F6TB transmitter can adjust three channels of small rudder proportion (CH1,CH2...CH20) .
During use, you can through the “D/R” switch on the left of transmitter to realize the small and big
rudder change. Please note that, when clicked “D/R” switch, the rudder of three channels
change at the same time; Switch up is big rudder, switch down is under small rudder.
FLY-DREAM
WWW.FD-RC.COM
4.4
Power supply setting
Press “ENTER” gets into “low power setting” interface,screen display as:
Press “UP” or
“DOWN”
Press “UP” or “DOWN” key to change low power supply scheme, F6TB can choose 1 s lithium
battery (1 c. LP), 2 s lithium batteries (2 c. LP) or 4 cell dry battery, nickel metal hydride, nickel
cadmium battery (4 c. NH). Different low power supply scheme, the system will automatically
adjust alarm voltage value; make sure that the users' battery won’t over discharge. After confirm
press “ENTER” save the setting and gets into “Bind” interface. Press “EXIT” button exit setting
4.5 Bind setting
Press”ENTER” button and gets into “Bind “ interface,screen display as:
Press “UP” or
“DOWN”
Press “UP” or “DOWN” gets into the bind settings, screen four eight segment code position in
turn display “-”, the transmitter stops working, start to transmit code information. Hold the button
under “V3” of IS-6R and supply power to it, the red LED receiver on lights up, released the button
before the red LED off, the red LED will flash 6 times, suggests that bind success. Press the
“EXIT” three times, transmitter will exit bind setting and gets into normal working state. Supply
power to receiver again, receiver gets into normal working.
Notice: Once the receiver was bind, it will be automatic initialization; the earlier failsafe
information will be cleared, so after bind please reset the failsafe.
FLY-DREAM
WWW.FD-RC.COM
Press “ENTER”
5 Senior menu
Press “ENTER” and turn on the transmitter gets into senior menu.You can set timer and power.
Press “EXIT”
5.1 Timer setting
After into the senior menu, press “ENTER” button get into “timer setting” interface, screen
display model number and timing time (unit for minutes). Such as: the current screen display :
1-01, indicating that the model NO. 1 time for 01 minute. Press the “UP” or “DOWN” key to
change timing, press “ENTER” key to change model number.
After finished, press “EXIT” save the setting and back to senior menu interface. Switch down the
timer, screen will display as follow:
Put up the throttle stick, at the beginning of timer; Throttle stick in idle, pause timer; Timing to the
set value, the remote control buzzer will slow ring alarm; switch up the timer, closed down the
timer.
5.2 Transmit power setting
After into senior menu, press “EXIT” into “Transmit power ”
FLY-DREAM
WWW.FD-RC.COM
6 Mode choices
Press “ENTER” and “EXIT” at the same time turn on the transmitter then into mode choice
interface, you can choose “hand type choice” and “country and area choice” two settng.
Press “ENTER”
Press “EXIT”
6.1 Hand Type Choice
After into”Mode choice” interface, press “ENTER” into “hand type choice” interface,screen
display the current hand mode. Press “UP”or “DOWN” change hand mode.Press “EXIT” save
setting and back to the senior menu interface.
There are four kind of hand model for choosing(F6TB)
Make the switch on the back of F6TB to MODE1 mode, press “UP” or “DOWM” can choose
Mode1 or Mode3, Make the switch on the back of F6TB to MODE2 mode, press “UP” or
“DOWN” buttons can choose Mode2 or Mode4
After finished, press “EXIT” button save the setting and back to “Mode choices” interface.
Switch to
MODE1
Press “UP” or
“DOWN”
Switch to
MODE2
Press “UP” or
“ DOWN”
FLY-DREAM
10
WWW.FD-RC.COM
6.2 Country and area choice
After into “mode choice”interface, press “EXIT” button into “Country and area choice”
interface,screen display the current country. Press UP and DOWN buttons can choose
countries.
Four eight segment code position shows “CU - 0”, said the international general range.
Four eight segment code position shows “CU - 1”, said France frequency range.
After finished the choice, press “ENTER” button save the setting and back to “Mode choices”
main interface.
Press “UP”
or “ DOWN”
7 Failsafe
Failsafe function is used for various reasons (such as: electromagnetic interference, distance too
far, transmitter without electricity, etc.) and lead to the receiver loss control. Set the failsafe,
when the receiver lost signal, it will make the servo position or ESC output returns to the pre-set
value automatically, which protect the model maximum
Setting:
1) After succeed binding of IS-6R, turn on F6TB.
2) Press and hold the button on the receiver (under the symbol of “Thumb”), connect the
receiver to the battery. The LED on the receiver will light (about 1s) and then go out (about
1s),At this time (when the LED off) remove your hand from the receiver button. If you didn’t
remove your hand in time , please operate again as above.
3) Move the joystick on your transmitter to where you want the surfaces / motor etc to be in the
event of lost signal. Press the button on the receiver .The LED will flash several times; this
shows the receiver has remembered the position which you have set. In the rare event that
your system losses signal, all channels will return to the position which you have set.
4) Turn off the power to the receiver. Failsafe is now set.
8 Simulator mode
Insert one side of simulator 3.5 audio nipple into F6TB “D.S.C” hole, the screen will display as:
The RF function of F6TB is closed, the transmitter output PPM signal to simulator for computer
simulation of flight.
FLY-DREAM
11
WWW.FD-RC.COM
FCC WARNING
Caution: Any changes or modi?cations to this device not explicitly approved by
manufacturer could void your authority to operate this equipment.
This device complies with part 15 of the FCC Rules. Operation is subject to the
following two conditions: (1) This device may not cause harmful interference, and (2)
this device must accept any interference received, including interference that may cause
undesired operation.
Control Information
This device is in accordance with the requirements in Radio / Telecommunications Terminal
Equipment Directive 1995/5/EC.
This device complies with the requirements in EMC Electromagnetic Compatibility Directive
2004/108/EC and Low Voltage Directive 2006/95/EC.
FLY-DREAM
12
WWW.FD-RC.COM

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.4
Linearized                      : No
XMP Toolkit                     : 3.1-702
Modify Date                     : 2013:03:21 15:29:17+08:00
Create Date                     : 2013:03:19 14:50:42+08:00
Metadata Date                   : 2013:03:21 15:29:17+08:00
Creator Tool                    : PScript5.dll Version 5.2
Format                          : application/pdf
Title                           : F6TA Manual v3.2.pdf
Creator                         : Administrator
Document ID                     : uuid:6041c9cc-9fa2-4587-9853-2b5bb4343a6a
Instance ID                     : uuid:76d2ebe4-ff0e-461e-8cbe-07d34eacd5b2
Producer                        : Acrobat Distiller 7.0 (Windows)
Has XFA                         : No
Page Count                      : 12
Author                          : Administrator

EXIF Metadata provided by EXIF.tools