YONGNUO PHOTOGRAPHIC EQUIPMENT RF605C Wireless Flash Trigger User Manual PMZ SMS 021 605 V1 1

SHENZHEN YONGNUO PHOTOGRAPHIC EQUIPMENT CO., LTD Wireless Flash Trigger PMZ SMS 021 605 V1 1

Contents

User manual part 2

Shutter release function Connect the shutter connecting cable: need to use(or purchase additional)the corresponding type of the LS-2.5 series shutter connecting cable. As the picture 1 shown, use the shutter connecting cable to connect between the camera shutter socket and transceivers. 1.RF-602 mode: Supports wireless shutter release, the transmitter set to “TX”stauts,the receiver set to “RX”.2.RF-603 mode: Supports wired shutter/wireless shutter release, all transceivers set to “TRX”stauts.As the picture 2 shown, half press the multifunction button on the transceiver(transmitter), the camera will focus. The focus light bright (Green),full press the button, the camera will shoot, meanwhile the shutter indicator light bright (Red).In RF-603 mode, single transceiver can be used as wired shutter release (as the picture 3 shown).8Picture1 Picture2 Picture3
Function extension2.Wireless remote shooting and sync trigger the flash: Multiple RF605 combination, it need LS-2.5 shutter connecting cable and multiple RF605 transmitters. To realize this function, all the transceivers need to set in RF-603"TRX" status. 1).Install one transceiver on the hot shoe of the camera, and connect the shutter socket with the shutter connecting cable to the camera.2).Fix and install the receivers and flash.3).Handhold one transceiver as remote control transmitter, full press the multifunction button to remote shooting, the flash will sync flash in triggering.91.Use the PC interface to trigger other types of flashes: realize the function need to additional purchase the Yongnuo LS-PC series connecting cable according to different interfaces.As the picture shown, connect the receiver and flash through the PC cable, the flash will sync flash in triggering.
1.Unable to power on or wireless trigger the flash FMake sure the equipment with adequate power, the transceiver use the same channel and communication mode. FWhen set in TX status , press the testing button to test flash, in RX and TRX status could not test flash. FMake sure the flash is ready and the flash has set in manual (M) mode. FMake sure the transceiver, camera and flash in normal contact, or it will lead to triggering problem. 2.Unable to awake the flash FWhen using the non specialized transmitter, it need to half press the button of transmitter to awake the flash when the transmitter set in TX state. If the flash could not be awaken, it need to manual awake the flash or turn off the power saving mode.3. The shutter could not be releasedFWhen part of the cameras could not find the focus, it could not proceed to shoot even if receiving the shooting signal. The focus mode of camera should be adjusted to “M”. 10Troubleshooting
Type: FSK 2.4GHz wireless remote control systemTransmission distance: 100mChannels:16 channelsGroup:6 GroupsShutter release: half-press, full-pressShutter interface: 2.5mm socketStudio flash light interface: standard PC socketMax Sync Speed: 1/320 secondBattery: AAA×2(3V )Stand-by time: about 90 hours in TX status, about 30 hours in TRX (RX) status. Size : 85MM x 41MM x 35MMThe functions of this user manual are based on test conditions of our company. Further notice will not be given if the design and specifications change.The YONGNUO logo in this manual includes the registered trademark or trademark of Shenzhen Yongnuo Photography Equipment Co.,Ltd in China or/and other countries(regions).All other trademarks are the property of their respective owners.Specification11
FCCID:2ACYP‐RF605CThisdevicecomplieswithPart15oftheFCCRules.Operationissubjecttothefollowingtwoconditions:(1)thisdevicemaynotcauseharmfulinterference,and(2)thisdevicemustacceptanyinterferencereceived,includinginterferenceChangesormodificationsnotexpresslyapprovedbythepartyresponsibleforcompliancecouldvoidtheuser'sauthoritytooperatetheequipment。Note:ThisequipmenthasbeentestedandfoundtocomplywiththelimitsforaClassBdigitaldevice,pursuanttopart15oftheFCCRules.Theselimitsaredesignedtoprovidereasonableprotectionagainstharmfulinterferenceinaresidentialinstallation.Thisequipmentgenerates,usesandcanradiateradiofrequencyenergyand,ifnotinstalledandusedinaccordancewiththeinstructions,maycauseharmfulinterferencetoradiocommunications.However,thereisnoguaranteethatinterferencewillnotoccurinaparticularinstallation.Ifthisequipmentdoescauseharmfulinterferencetoradioortelevisionreception,whichcanbedeterminedbyturningtheequipmentoffandon,theuserisencouragedtotrytocorrecttheinterferencebyoneormoreofthefollowingmeasures:—Reorientorrelocatethereceivingantenna.—Increasetheseparationbetweentheequipmentandreceiver.—Connecttheequipmentintoanoutletonacircuitdifferentfromthattowhichthereceiverisconnected.—Consultthedealeroranexperiencedradio/TVtechnicianforhelp.

Navigation menu