YUXINXIN ELECTRONICS 2011071501A Audio Transmitter User Manual Manual

Download:
Mirror Download [FCC.gov]
Document ID	1526944
Application ID	FkoklGlUhrZx3O2Mrf3HyA==
Document Description	Manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	21.16kB (264548 bits)
Date Submitted	2011-08-22 00:00:00
Date Available	2011-08-22 00:00:00
Creation Date	2011-08-03 09:22:08
Producing Software	Acrobat Distiller 8.1.0 (Windows)
Document Lastmod	2011-08-03 09:23:26
Document Title	Manual
Document Creator	Acrobat PDFMaker 8.1 for Word
Document Author:	雨林木风

FM‐8898 ‐ Instruction Manual
Multifunction Wireless Headphones
Features
■Multifunction wireless headphones
■Radio FM built‐in
■Microphone built in receiver
■Room monitoring feature
■Possible to use as wired headphones (without battery)
■Frequency response 20Hz – 20KHz
■Receiver powered from battery or power adaptor (not included)
■Transmission frequency: 88.3 MHz
■Receiver frequency range: 88‐108MHz
■Weight: 173g (without battery)
Package Includes
■ Receiver
■Headphones
■USB power cable
■Jack‐jack audio cable
■Cinch‐jack audio cable
NOTE. Batteries are not included
Preparation
1. Insert 2 AAA batteries according to polarity marks (+/‐) to the compartment located in left
“L” earphone.
2. Use volume knob (2) to switch headphones ON. If power LED (5) is lighting – batteries has been
installed correctly and are in good condition.
3. You can power receiver in 3 ways: from USB port in computer (use attached USB power cable),
from external 4,5V power adaptor (not included in the set) from 2 AAA batteries. Choose one of
ways
4. If You decided to use external power insert power plug into power socket (10).
5. If You decided to use batteries, insert 2 AAA alkaline batteries to the compartment located
on the bottom of receiver. Remember about polarity marks.
IMPORTANT. Do not use external power or USB power, when batteries are inserted in receiver.
1st remove the batteries.
IMPORTANT. Use only alkaline batteries.
Parts Identification
Headphones
1. Battery compartment
2. Volume control and
3. Scan button (SCAN)
4. Reset button (RESET)
5. Power indicator power switch
Receiver
6. Audio socket
7. Power indicator (front)
8. Power and function switch
9. Microphone socket (MIC)
10. Power socket 4,5V DC
11. Microphone (MIC)
12. Output audio cable
13. Battery compartment (bottom)
Operation
Wireless headphones
Set receiver function switch to WIRELESS HEADPHONE position. Connect as shown on picture
“Fig.1”. Switch ON the headphones with pow‐er/volume switch. Push RESET button and then
SCAN button.
Wireless headset (for PC net audio chat)
Set receiver function switch to AUDIO CHAT position. Connect as shown on picture “Fig.2”
including microphone cable to microphone socket in the computer. Place the receiver close to
speaking person (about 1 meter) and aim microphone “Fig.3”. Switch ON the headphones with
power/ volume switch. Push RESET button and then SCAN button.
Monitoring
This mode require battery power for the receiver. Set receiver function switch to MONITORING
position. Place receiver close the person You want to monitored (np. elderly peoples, kids).
Switch ON the headphones with power/volume switch. Push RESET button and then SCAN
button.
Listening radio FM
For listening radio FM receiver is useless. Switch ON the headphones with power/volume switch.
Push RESET button and then SCAN button. Radio will automatically find active radio channel.
To change the station (frequency) push SCAN button again. When the top frequency will be
reached, please push RESET button and SCAN to begging from the start of the frequency scale.
Wired headphones
For using headphones as wired the receiver is useless. Use the audio cable (jack to jack) to
connect headphones to sound source. Battery power in headphones is not necessary.
Note. Always switch off receiver and headphones when not used to save battery.
FCC Part 15
This device complies with Part15 of the FCC Rules. Operation of this product is subject to the following two
conditions:
(1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that may cause undesired
operation.
This equipment has been tested and found to comply within the limits for a class B digital device, pursuant to Part
15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception, which can be determined by turning the equipment
off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
•Reorient or relocate the receiving antenna.
•Increase the separation between the equipment and receiver
.•Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
•Consult the dealer or an experienced technician for help.
FCC warning
Changes or modifications not expressly approved by the party responsible for compliance with the FCC Rules
could void the user’s authority to operate this equipment.

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.6
Linearized                      : No
Tagged PDF                      : Yes
XMP Toolkit                     : Adobe XMP Core 4.0-c320 44.284297, Sun Apr 15 2007 17:19:00
Producer                        : Acrobat Distiller 8.1.0 (Windows)
Company                         : 德普沙井电子城B311柜
Source Modified                 : D:20110803011950
Create Date                     : 2011:08:03 09:22:08+08:00
Creator Tool                    : Acrobat PDFMaker 8.1 for Word
Modify Date                     : 2011:08:03 09:23:26+08:00
Metadata Date                   : 2011:08:03 09:23:26+08:00
Document ID                     : uuid:d27360cc-0926-4d78-b645-7af2ae3f3b28
Instance ID                     : uuid:e984ac20-9f31-4c3e-b087-092606b75cb1
Subject                         : 3
Format                          : application/pdf
Creator                         : 雨林木风
Title                           : 
Has XFA                         : No
Page Count                      : 7
Page Layout                     : OneColumn
Author                          : 雨林木风

EXIF Metadata provided by EXIF.tools