YUXINXIN ELECTRONICS 20151215 Wireless TV Earphones User Manual

SHENZHEN YUXINXIN ELECTRONICS CO.,LTD Wireless TV Earphones Users Manual

Users Manual

Fold Fold Fold Fold FoldLOCATION OF PARTS AND CONTROLS  1. Earphones2. Transmitter3. Volume Dial4. Power Switch5. Tone Dial6. Balance Knob7. LINE-IN Port8. Battery Door Cover9. MIC-IN Port10. CHANNEL Button11. Power LED12. RF Reception LED13. Power Switch14. DC-IN Port15. AUDIO- IN Port16. MIC-IN Port17. SCAN Button18. Charging Pins/Contacts19. Power LED20. Audio LED21. Microphone22. Li-ion Rechargeable Battery23. AC/DC Adapter24. Audio Cable25. 3.5mm(female)-to-RCA(male)Y-CableWireless TV EarphonesENJOY THE SHOW-WITHOUTDISTURBING OTHERSLITHIUM-ION BATTERY WARNINGSThis device contains a non-removable lithium-ion battery. The battery must berecycled or disposed of properly. Contact your local waste management office for information on battery recycling or disposal.FCC INFORMATIONThis equipment has been tested and found to comply with the limits for a Class B Digital Device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined  by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:•    Reorient or relocate thereceiving antenna.•    Increase the distance betweenthe equipment and receiver.•    Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.•    Consult the dealer or an experienced radio/TV technician for help.This device complies with  Part 15 of the FCC Rules.  Operation is subject to the  following two conditions:1.  This equipment may not cause harmful interference.2.  This equipment must accept any interference received, including interference that may cause undesired operation.Modifications not authorized by themanufacturer may void the user’sauthority to operate this device. This equipment complies with FCC RFradiation exposure limits set forth for an uncontrolled environment. This  transmitter must not be co-located or operating in conjunction with any otherantenna or transmitter.FCCID: ZRH-20151215Merrimack, New Hampshire, USA 03054 800-846-3000 • Brookstone.comLOCATION OF PARTS AND CONTROLS (EARPHONES) LOCATION OF PARTS AND CONTROLS (TRANSMITTER) LOCATION OF PARTS AND CONTROLS (ACCESSORIES) 2324252122201918171615141354310987611 1212311673
dloFdloFdloFCHARGING THE EARPHONES1. Carefully open the Battery Door Coverand insert the Li-ion Battery (included)according to the polarity markings.Replace the Battery Door Cover.TROUBLE SHOOTING NO SOUND• Ensure the AC/DC adapter is securelyplugged into the transmitter.• Ensure the earphones arepowered on.• Ensure the earphones and thetransmitter are synced.• The earphones may need to becharged.• The earphones may need to movecloser to the transmitter.• Ensure the audio device isswitched ON.• The volume of the audio device mayneed to be increased. • If there is interference or poor signalreception, audio from the earphoneswill mute and the Power LED will flashRED. Press the SCAN Buttons on transmitter and CHANNEL Buttonon earphones at the same time for 10 seconds until the earphones’ RF LED turn SOLID BLUE again.USING THE EARPHONESWITH THE DIRECT PLUG1. Connect the earphones directlyto an audio source by plugging oneend of a 3.5mm-to-3.5mm cable(included) into the AUX-IN Port at the bottom of the earphones and other end into the audio source.2. Use the volume controls on the audiosource to change the volume.Note:When using a 3.5mm-to 3.5mm cable,the two LEDs are off.TRANSMITTER SET UP1. Plug the AC/DC power adapter intothe DC Port located on the rear of the transmitter. Plug the other end of the AC/DC power adapter into an electrical wall outlet.2. Slide the Power Switch to ON . Thetransmitter’s Power LED is solidGREEN.NOTE: If the earphones are dockedon the transmitter and in low battery,the transmitter’s Power LED is solidORANGE. The earphones are beingcharged.3. Connect the transmitter to an audiosource using the included RCA andaudio cables.4. When the transmitter receives an audio signal, the AUDIO LED is solidGREEN. If no audio signal is detected, theAUDIO LED is solid ORANGE.NOTE:Plug in the included external microphone in the MIC-IN Port at the rear of the transmitter to perform monitoring function. CARE AND STORAGE1. Dust the earphones and transmitterwith a soft, dry cloth.2. Store the earphones and transmitterin a cool, dry place.SPECIFICATIONSPower Supply (Transmitter):DC 5V, 500mA Power Supply (Earphones):3.7V 420mAhFrequency: 2.402-2.480 GHz Digital Transmission mode: GFSKRange: Up to 100ft/30m & 75ft/25m with some obstructions S/N Ratio: 75dBFrequency Response: 30Hz~20KHz Charging Time: Approx. 3 hours(subsequent uses after first initial charge of 12 hours)Battery Life: Approx. 8 hoursUSING THE EARPHONESWITH TRANSMITTER1. To turn the earphones on, slide thePower Switch to ON. The Power LED is solid RED.2. The earphones will automaticallysync to the transmitter when the transmitter is with audio signal in. When the earphones are attempting to set up a connection with the transmitter, the Power LED will blinkRED. When the earphones and transmitter are synced, the earphones’ RF LED is solid BLUE and the transmitter’s AUDIO LED is GREEN.3. Use the Volume Dial on theearphones and the audio sourceto  change the volume.4. Adjust the Tone Dial to your desiredbass performance.5. Use the Balance Knob to adjustsound clarity of the right and leftchannels.6. After 5 minutes of no audio signaldetected, the AUDIO LED on transmitter turns solid ORANGE should be earphones power LEDblinking RED.7. To turn the earphones off, slide the Power Switch to OFF. The LEDswill turn off.2. For first time use, charge the Earphones for at least 12 hours. To charge earphones, ensure the earphones are OFF by sliding thePower Switch to OFF on earphonesuntil the two LEDs are off. Place theearphones on the top of transmitterensuring the charging contacts are aligned.  When the earphones are fully charged the Power LED is solidGREEN.Note:Insert the external microphone to the MIC-IN Port at the bottom of the earphones, audio signal will be pausedand now the earphones perform as a hearing aid device. Audio signal resumewhen the microphone is unplugged.

Navigation menu