YUXINXIN ELECTRONICS 20151216 Digital Wireless TV Headphone User Manual

Download:
Mirror Download [FCC.gov]
Document ID	2939485
Application ID	SDtu8U2M848Srh5x93Kiog==
Document Description	User Manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	69.7kB (871223 bits)
Date Submitted	2016-03-23 00:00:00
Date Available	2016-03-23 00:00:00
Creation Date	2016-01-14 10:30:29
Producing Software	Acrobat Distiller 10.0.0 (Macintosh)
Document Lastmod	2016-01-14 10:30:29
Document Title	User Manual
Document Creator	Adobe Graphics Manager
Document Author:	mac-mini

Fold
Digital Wireless
TV Headphones
ENJOY THE SHOW-WITHOUT
DISTURBING OTHERS
Fold
Fold
LITHIUM-ION BATTERY
WARNINGS
• Reorient or relocate the
receiving antenna.
LOCATION OF PARTS AND
CONTROLS
This device contains a non-removable
lithium-ion battery. The battery must be
recycled or disposed of properly.
Contact your local waste management
office for information on battery
recycling or disposal.
• Increase the distance between
the equipment and receiver.
1. Headphones
2. Transmitter
3. Power On/Off switch
4. BASS/NORMAL Switch (RF mode)
5. Volume Up Button
6. SCAN Button
7. Volume Down Button
8. Power/RF Reception LED
9. AUX-IN Port
10. Charging Contacts
11. Charging Contacts/Pins
12. CHARGE LED
13. POWER LED
14. DC-In Port
15. Audio-In Port
16. SCAN Button
17. Power ON/OFF Switch
18. AC/DC Adapter
19. Audio Cable
20. 3.5mm(female)-to-RCA(male)
Y-Cable
FCC INFORMATION
This equipment has been tested
and found to comply with the
limits for a Class B Digital Device,
pursuant to Part 15 of the FCC
Rules. These limits are designed to
provide reasonable protection against
harmful interference in a residential
installation. This equipment generates,
uses, and can radiate radio frequency
energy and, if not installed and used
in accordance with the instructions,
may cause harmful interference to
radio communications. However, there
is no guarantee that interference will
not occur in a particular installation.
If this equipment does cause harmful
interference to radio or television
reception, which can be determined
by turning the equipment off and
on, the user is encouraged to try to
correct the interference by one or
more of the following measures:
• Connect the equipment to an outlet
on a circuit different from that to
which the receiver is connected.
• Consult the dealer or an
experienced radio/TV technician
for help.
This equipment complies with
Part 15 of the FCC Rules.
Operation is subject to the
following two conditions:
1. This equipment may not cause
harmful interference.
2. This equipment must accept any
interference received, including
interference that may cause
undesired operation.
Modifications not authorized by the
manufacturer may void the user’s
authority to operate this device.
This equipment complies with FCC RF
radiation exposure limits set forth for
an uncontrolled environment. This
transmitter must not be co-located or
operating in conjunction with any other
antenna or transmitter.
FCCID: ZRH-20151216
Fold
Fold
LOCATION OF PARTS AND
CONTROLS (HEADPHONES)
LOCATION OF PARTS AND
CONTROLS (TRANSMITTER)
LOCATION OF PARTS AND
CONTROLS (ACCESSORIES)
11
18
12 13
19
20
10
14 151617
311672
Merrimack, New Hampshire, USA 03054
800-846-3000 • Brookstone.com
Fold
CHARGING THE HEADPHONES
TRANSMITTER SET UP
1. For first time use, charge the
headphones for 12 hours.
2. To charge the headphones, ensure
the headphones are OFF by sliding
the Power Switch to OFF on
headphones until the Power LED is
OFF. Place the headphones on the
top of transmitter ensuring the
charging contacts are aligned. The
transmitter’s CHARGE LED will blink
BLUE to show the headphones are
charging. When the headphones
are fully charged, the CHARGE LED
is solid BLUE.
1. Plug the AC/DC power adapter into
the DC Port located on the rear of
the transmitter. Plug the other end
of the AC/DC power adapter into
an electrical wall outlet.
2. Slide the Power Switch to ON . The
transmitter’s Power LED is solid
RED.
3. Connect the transmitter to an audio
source using the included RCA and
audio cables.
Note:
If CHARGE LED disappears, please
check if the charging contacts of both
the headphones and transmitter are
well aligned.
Fold
Fold
USING THE HEADPHONES
WITH TRANSMITTER
USING THE HEADPHONES
WITH WIRED CONNECTION
TROUBLE SHOOTING
NO SOUND
1. To turn the headphones on, slide the
Power Switch to ON. The Power/RF
LED is in solid RED.
2. The headphones will automatically
sync to the transmitter. When the
headphones are attempting to set up
a connection with the transmitter, the
Power/RF LED will blink RED.
When the headphones and
transmitter are synced, the
headphones’ LED is solid BLUE.
3. Use the Volume buttons on the
headphones and the audio source
to change the volume.
4. Slide the BASS/NORMAL Switch to
BASS for bass boost function under
RF wireless mode.
Note: It has no bass boost function
under wired connection.
5. After 5 minutes of no audio signal
detected, the Power/RF LED turns
solid RED.
6. To turn the headphones off, slide
the Power Switch to OFF. The
Power/RF LED will light off.
1. Connect the headphones directly
to an audio source by plugging one
end of a 3.5mm-to -3.5mm cable (
included) into the AUX-IN Port at the
bottom of the headphones and other
end into the audio source.
2. Use the volume controls on the audio
source to change the volume.
• Ensure the AC/DC adapter is
securely plugged into the transmitter.
• Ensure the headphones are
powered on.
• Ensure the headphones and the
transmitter are synced.
• The headphones may need to be
charged.
• The headphones may need to move
closer to the transmitter.
• Ensure the audio device is switched
ON.
• The volume of the audio device may
need to be increased.
• If there is interference or poor signal
reception, audio from the headphones
will mute and the Power/RF LED is
solid RED. Press the SCAN Buttons
on transmitter and on headphones
at same time for 10 seconds until the
headphones’ LED turn SOLID BLUE
again.
CARE AND STORAGE
1. Dust the headphones and transmitter
with a soft, dry cloth.
2. Store the headphones and transmitter
in a cool, dry place.
SPECIFICATIONS
Power Supply (Transmitter):
DC 5V, 300mA
Power Supply (Headphones):
3.7V 900mAh
Frequency: 2.4-2.48 GHz Digital
Transmission mode: GFSK
Range: Up to 100ft (approx. 30m)
S/N Radio: 75dB
Frequency Response: 30Hz~20KHz
Charging Time: Approx. 4 hours
(subsequent uses after first initial
charge of 12 hours)
Battery Life: Approx. 12 hours

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.6
Linearized                      : Yes
Author                          : mac-mini
Create Date                     : 2016:01:14 10:30:29+08:00
Modify Date                     : 2016:01:14 10:30:29+08:00
Title                           : 
XMP Toolkit                     : Adobe XMP Core 5.2-c001 63.139439, 2010/09/27-13:37:26
Metadata Date                   : 2016:01:14 10:30:29+08:00
Creator Tool                    : Adobe Graphics Manager
Format                          : application/pdf
Creator                         : mac-mini
Document ID                     : uuid:cce4ecf9-b237-3243-a4b0-65f9cd3920ca
Instance ID                     : uuid:0f919491-5eb5-5145-bf3c-904f37c61376
Producer                        : Acrobat Distiller 10.0.0 (Macintosh)
Page Count                      : 2

EXIF Metadata provided by EXIF.tools