Yaesu Musen 0A300910 ULTRA LOW POWER WIFI MODULE User Manual Operating Manual

Download:
Mirror Download [FCC.gov]
Document ID	3645809
Application ID	p79VLqvQiLZW8d21NcnnWQ==
Document Description	Operating Manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	Yes
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	29.05kB (363160 bits)
Date Submitted	2017-11-20 00:00:00
Date Available	2017-11-20 00:00:00
Creation Date	2017-11-06 10:42:42
Producing Software	Adobe PDF Library 10.0.1
Document Lastmod	2017-11-15 14:39:03
Document Title	Operating Manual
Document Creator	Adobe InDesign CS6 (Windows)

・The antenna cable can be cut and spliced to ease installation. Care must be taken when reconnecting
the antenna cable to protect from water and corrosion.
2. Mount the antenna base to the antenna using the supplied three screws.
3. Screw the antenna base to the mounting bracket or extension pole.
4. Install the mounting bracket or extension pole.
SCU-30
Wireless Access Point
Flush Mounting the antenna
The SCU-30 is wireless access point supplied with 5 feet of cable that plugs into your compatible Standard Horizon VHF radio to wireless connect with the SSM-71H Wireless Remote Access Microphone
RAM4W. Please refer to the STANDARD HORIZON products catalog or web site for compatibility.
NOTE: Before drilling the mounting holes, it is
recommended to verify correct operation in the desired location.
1. To ease installation use the supplied flush
mount template.
2. Apply the flush mounting template sticker.
3. Drill the 0.78” (20 mm) and 0.13” (3.2 mm)
holes, and remove the template.
4. Insert the cable into the 0.78” (20 mm) hole
and route to the transceiver.
5. Apply a small amount or RTV to the underside of the antenna.
6. Place the antenna and screw into place using the supplied screws.
Owner’s Manual
The details of the installation and operation of the SCU-30 are included in the owner’s manual of
the compatible fixed mount radio, or can be downloaded at www.standardhorizon.com.
Safety Precautions (Be Sure to Read)
Be sure to read the safety precautions of Operating Manual of the compatible fixed mount VHF
radio to use this product safely.
Supplied Accessories
Antenna Unit (5 feet cable)..................................................................................................................... 1
Antenna Base (Socket, Part number: RA6054200) ............................................................................... 1
Screws (M3X8 SUS, Part number: U20308020) ................................................................................... 3
Template
cut here
Installing
TEMPLATE for the SCU-30
The SCU-30 is designed to be mounted on a base, installed on an extension pole or flush mounted.
Choose a location for the antenna unit that has not located within 3 feet of radar or other transmitting
antenna. Ensure there are no major obstructions or fixtures in the immediate proximity to the antenna unit. If you are unsure of the location, temporarily mount the antenna to verify correct operation. If
mounted close to a radar, turn on the radar and check the to verify correct operation.
Antenna Unit
Compass Safe Distance
This antenna unit at least 0.2m (0.66 feet) from magnetic compass.
φ3.2 mm [0.13 inch]
Base Mounting the antenna
φ3.2 mm [0.13 inch]
Antenna Base
1. When passing the antenna cable through a mounting
bracket or extension pole, make sure to pass the cable through the antenna base.
NOTES:
・When routing the antenna cable along the outside of
the extension pole, pass the cable through the groove
as shown by the dotted lines in the figure on the right.
(Please cut the blank panel with a long-nose pliers.)
φ20 mm [0.78 inch] or greater
Antenna Cable
φ3.2 mm [0.13 inch]
Pole
cut here
The thread used on the base of antenna (1 inch, 14 TPI)
is an industry standard used on a wide range of commercially available mounting brackets or extension poles.
Due to the manufacturing process of the mounting brackets, the antenna may not tighten all the way down onto all
the threads. This is of no concern however as the antenna must be tightened until the antenna stops rotating.
Use this template to mark the
location where the hole for
the flush mount is to be cut.
Dimensions
Yaesu Musen Co. Ltd is responsible for ensuring that the end-user has no manual instructions to remove or install module.
85 mm
60 mm
The Wireless Networking Module is limited to SCU-30 installation ONLY.
This equipment is defined as a transmitting device designed to be used in other than fixed locations. In this
context, the term “fixed location” means that the device is physically secured at one location and is not able to be
easily moved to another location.
30 mm
This equipment complies with FCC and IC radiation exposure limits set forth for an uncontrolled environment. This
equipment should be installed and operated with minimum distance 20 cm between the radiator and your body.
EU Declaration of Conformity
We, Yaesu Musen Co. Ltd of Tokyo, Japan, hereby declare that this radio equipment SCU-30 is in full compliance with
EU Radio Equipment Directive 2014/53/EU. The full text of the Declaration of Conformity for this product is available
to view at http://www.yaesu.com/jp/red
ATTENTION – Conditions of usage
RF Exposure
This transceiver works on frequencies that are regulated and not
permitted to be used without authorisation in the EU countries shown
in this table. Users of this equipment should check with their local
spectrum management authority for licensing conditions applicable for
this equipment.
The RF output power of the module is 0.095 Watts. This power output is below the RF exposure
threshold for use mobile devices. See FCC document KDB 447498 for additional information.
FCC Notice
Unauthorized changes or modifications to this equipment may void compliance with FCC Rules. Any change or
modification must be approved in writing by STANDARD HORIZON.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part
15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the
following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
THIS DEVICE COMPLIES WITH PART 15 OF THE FCC RULES. OPERATION IS SUBJECT TO THE FOLLOWING TWO
CONDITIONS: (1) THIS DEVICE MAY NOT CAUSE HARMFUL INTERFERENCE, AND (2) THIS DEVICE MUST ACCEPT
ANY INTERFERENCE RECEIVED, INCLUDING INTERFERENCE THAT MAY CAUSE UNDESIRED OPERATION.
Changes or modifications to this device not expressly approved by YAESU U.S.A. could void the User’s authorization to operate this device.
This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to the following
two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device.
Le présent appareil est conforme aux CNR d’Industrie Canada applicables aux appareils radio exempts de licence.
L’exploitation est autorisée aux deux conditions suivantes : (1) l’appareil ne doit pas produire de brouillage, et (2)
l’utilisateur de l’appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d’en
compromettre le fonctionnement.
AT
DK
GR
LU
RO
LI
BE
ES
HR
LV
SK
NO
BG
EE
HU
MT
SI
–
CY
FI
IE
NL
SE
–
CZ
FR
IT
PL
CH
–
DE
UK
LT
PT
IS
–
Disposal of Electrical and Electronic Equipment
Products with the symbol (crossed-out wheeled bin) cannot be disposed as household waste.
Electronic and Electrical Equipment should be recycled at a facility capable of handling these items
and their waste byproducts.
Please contact a local equipment supplier representative or service center for information about the
waste collection system in your country.
Specifications
Supply Voltage:
Power Consumption:
Operating Temperature:
Storage Temperature:
Wireless Networking Module:
Frequency Band:
RF Output Power:
Wireless Networking Standard:
Dimensions:
Weight (approx., without cable):
Cable (approx.):
Normal: 13.8 VDC (Supplied from the transceiver)
1.4 W (Max.)
−4 °F to +140 °F (−20 °C to +60 °C)
−22 °F to +185 °F (−30 °C to +85 °C)
FCC ID: K660A300910, IC: 511B-0A300910*
2412 to 2462 MHz
0.095 W
IEEE 802.11 b/g/n
85 x 30 mm in height (flush mounted) or 60 mm on base mount
2.8 oz (80 g)
5 feet (1.5 m)
* The original Gainspan Corporation grant notes indicate that the module was approved as single modular approval.
The module is only approved for use in mobile configurations.
* This module is for Yaesu Musen Co., Ltd's internal use only for their host, model SCU-30 which is an access point.
YAESU MUSEN CO., LTD.
Tennozu Parkside Building
2-5-8 Higashi-Shinagawa, Shinagawa-ku, Tokyo 140-0002 Japan
YAESU USA
6125 Phyllis Drive, Cypress, CA 90630, U.S.A.
YAESU UK
Unit 12, Sun Valley Business Park, Winnall Close
Winchester, Hampshire, SO23 0LB, U.K.
Printed in Japan
Statements and Requirements
This module has been approved as single modular approval. The module is limited to
installation in mobile or fixed applications according to FCC Rules Part 2.1091(b).
Separate approval is required for all other operating configurations, including portable
configurations with respect to FCC Rules Part 2.1093 and different antenna configurations.
The frequency range of the module is 2412 to 2462 MHz.
The radiated RF power output of the module is 0.095 Watts.
This module is for Yaesu Musen Co., Ltd’s internal use only for their host, model SCU-30 which
is an access point..
The host must have a label indicating the FCC ID of the module and be worded as follows.
Contains FCC ID: K660A300910
For ISED Canada the label must be worded: Contains IC: 511B-0A300910
RF Exposure
The RF output power of the module is 0.095 Watts or 95 mW. This power output is below the
RF exposure threshold for use mobile devices. See FCC document KDB 447498 for additional
information.
Host User Manual
The host user manual must contain wording that directs the user to the fact that:
“OEM integrators are responsible for ensuring that the end-user has no manual instructions to
remove or install module”.
The user manual for the host must contain the following regulatory wording. The wording below
satisfies both the FCC and ISED Canada requirements.
This device complies with part 15 of the FCC and Canadian Rules. Operation is subject to the following
two conditions:
(1) This device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that may cause undesired
operation.
Le présent appareil est conforme aux CNR d’Industrie Canada applicables aux appareils radio exempts
de licence. L’exploitation est autorisée aux deux conditions suivantes :
(1) l’appareil ne doit pas produire de brouillage;
(2) l’utilisateur de l’appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est
susceptible d’en compromettre le fonctionnement.
This equipment has been tested and found to comply within the limits of a Class B digital device pursuant
to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses, and can radiate radio frequency
energy and if not installed and used in accordance with the instructions, may cause harmful interference
to radio communications. However, there is no guarantee that interference will not occur in a particular
installation.
If this equipment does cause harmful interference to radio or television reception (which can be
determined by turning the equipment on and off), the user is encouraged to try to correct the interference
by using one or more of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and the receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help
Caution: Changes or modifications not expressly approved by the party responsible for compliance could
void the user's (or your) authority to operate the equipment.
This Class B digital apparatus meets all requirements of the Canadian Interference-Causing Equipment
Regulations.
Cet appareil numérique de la classe B respecte toutes les exigences du Règlement sur le matériel
brouilleur du Canada

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.6
Linearized                      : No
Create Date                     : 2017:11:06 10:42:42+09:00
Creator                         : Adobe InDesign CS6 (Windows)
Modify Date                     : 2017:11:15 14:39:03-05:00
XMP Toolkit                     : Adobe XMP Core 5.4-c005 78.147326, 2012/08/23-13:03:03
Metadata Date                   : 2017:11:15 14:39:03-05:00
Creator Tool                    : Adobe InDesign CS6 (Windows)
Instance ID                     : uuid:33372366-995a-4a71-a49d-8356ccbd699e
Original Document ID            : xmp.did:DFE581289478E6119530AA8853C7801A
Document ID                     : xmp.id:4F04FABF93C2E71183FAC24494BD7A0A
Rendition Class                 : proof:pdf
Derived From Instance ID        : xmp.iid:4E04FABF93C2E71183FAC24494BD7A0A
Derived From Document ID        : xmp.did:D96ADEB786C2E711AF78DD4EA6307284
Derived From Original Document ID: xmp.did:DFE581289478E6119530AA8853C7801A
Derived From Rendition Class    : default
History Action                  : converted
History Parameters              : from application/x-indesign to application/pdf
History Software Agent          : Adobe InDesign CS6 (Windows)
History Changed                 : /
History When                    : 2017:11:06 10:42:42+09:00
Format                          : application/pdf
Producer                        : Adobe PDF Library 10.0.1
Trapped                         : False
Page Count                      : 4

EXIF Metadata provided by EXIF.tools