Yaesu Musen 0F444X11 Bluetooth Headset User Manual BH 2 080220 pmd

Yaesu Musen Co., Ltd. Bluetooth Headset BH 2 080220 pmd

Manual 1

Controls & ConnectionsMicrophonePOWER switchVOLUME (–) switchPress this switch while pressing and holding the PTTswitch, to decreases the microphone gain.VOLUME (+) switchPress this switch while pressing and holding the PTTswitch, to increases the microphone gain.LED IndicatorBlinking Blue: When the BH-2 Bluetooth® Headset iscorrectly recognized by the transceiver.Blinking Red: When the BH-2 Bluetooth® Headset isnot correctly recognized by the trans-ceiver.Blinking Red/Blue: Battery Voltage is Low.PTT switchPress this key to transmit. Release this key to return toreceive (Depends on transceiver settings).SPEAKEREarhookYou can wear the BH-2 on your left or right ear.“BH-2” Bluetooth® Head SetWhen the optional BU-1 Bluetooth® Adapter Unit is installed in the Transceiver*, you may use the optional BH-2 Bluetooth® Headset as a wireless link to send and receive audio to the Transceiver*.* Check with your Vertex Standard Dealer or Catalog for applicable models.Wearing the BH-21. Open the earhook.2. Loop the earhook over your ear.3. Press the BH-2 to your ear.4. Adjust the flexible boom microphoneby bending the boom towards yourmouth.The BH-2 comes ready to fit the left ear. You may changethe BH-2 to fit the right ear in the following procedure.1. Remove the Earhook by pushing it out with a pointedobject.2. Insert the Earhook from the other side.PairingBefore you can use your BH-2 for the first time, the BH-2and the transceiver must be paired.Refer to the Transceiver’s Operating Manual for Pairing in-structions.PPlease bring the BH-2 and the Transceiver close togetherwhen doing Pairing.1. Make sure that the BH-2 is off.2. Press and hold the POWER switch for five seconds, untilthe LED indicator blinks red/blue alternately.When the BH-2 is correctly recognized (Requires a 20 to 30seconds) by the transceiver, the LED indicator will blinkblue.Effective Communications RangeThe communications range between the BH-2 and theTransceiver is around 10m (33 ft).Obstacles between the BH-2 and the Transceiver maydecreas the communications distance.When you move out of range, the beeper sounds a lowpitch tone. When you move back into range, the beepersounds a high pitch tone.Turning ON and OFFTTTTTo turn the o turn the o turn the o turn the o turn the BH-2 ON ON ON ON ONPress and hold the POWER switch for three seconds, un-til the BH-2’s LED indicator glows red, and the beepersounds a high pitch tone.When the BH-2 is correctly recognized by the transceiver,the LED indicator will blink blue.PWhen the BH-2 is not correctly recognized by the trans-ceiver, the LED indicator will blink red.TTTTTo turn the o turn the o turn the o turn the o turn the BH-2 OFF OFF OFF OFF OFFPress and hold the POWER switch for five seconds, untilthe BH-2’s red LED indicator blinks rapidly, the beepersounds two brief tones, and the BH-2 turns off.LED indicatorPOWER SwitchPOWER SwitchFor more comfort when wearing the BH-2, affix the sup-plied sponge on the speaker and press the supplied spongeball onto the earhook, and adjust as necessary.OperationTTTTTransmissionransmissionransmissionransmissionransmissionPress the PTT switch to transmit, and release the switchto return to receive (Depends on transceiver settings).Adjusting the VAdjusting the VAdjusting the VAdjusting the VAdjusting the Volume levelolume levelolume levelolume levelolume levelAdjust the receiver audio level, using the VOLUME (–) or(+) switch.When the audio level reaches the maximumor minimun, the beeper sounds two brief tones.VOLUME (+): Adjusts the receiver audio level upward.VOLUME (–): Adjusts the receiver audio level downward.Microphone Gain SettingMicrophone Gain SettingMicrophone Gain SettingMicrophone Gain SettingMicrophone Gain SettingPress and hold the PTT switch, while using the VOLUME(+) or (–) switch to select a comfortable Microphone gainlevel (Five steps). When the microphone gain reaches themaximum or minimun, the beeper sounds a high pitch tone.VOLUME (+): Sets the MIC gain upward.VOLUME (–): Sets the MIC gain downward.BatteryWhen the battery voltage becomes low, the BH-2’s LED indi-cator will blink red/blue alternately, and the beeper soundsa low pitch tone.If the battery has never been used, or its charge is depleted,it may be charged by connecting to the Charger Sleeve* orCharger Cradle*, as shown in the illustration.Please refer to the transceiver’s manual for installation ofthe Charger Sleeve.* Check with your Vertex Standard Dealer or Catalog for appli-cable models.1. Insert the BH-2 into the Charger Sleeve or Charger Cradle.NoteNoteNoteNoteNote: The BH-2 is automatically set to “sleep” mode,when it is inserted into the Charger Sleeve orCharger Cradle.When it is disconnect from the Charger Sleeve orCharger Cradle, the BH-2 will be active again.2. If the BH-2 is inserted correctly, the LED indicator willglow Red. A fully discharged battery will be charged com-pletely in 3 hours. When charging is finished, the LEDindicator will glow blue.BH-2 is not designed to attach to a motorcycle helmet.Specifications are subject to change without notice.VOLUME (+) SwitchVOLUME (–) SwitchPTT SwitchBattery saverBattery saverBattery saverBattery saverBattery saverIf there has been no signal or key button activity for 20 sec-onds, the Battery Save automatically puts the BH-2 in “sleep”mode, to conserve battery life.When a signal is received or the PTT key is pressed theBH-2 will be active again.Refer to the Transceiver’s Manual for Battery saver instructions.SpecificationsBluetooth specification Ver1.2Bluetooth profiles HSPRadio Frequency 2402 MHz - 2480 MHzModulation method GFSKTransmitter output power 0 dBm Class 2Receiver sensitivity <-80 dBmDistance (open area) 32 ft (10 meters)Audio format SBCAudio frequency range 100 Hz - 20 kHzPower supply Rechargeable Lithium-PolymerBattery life 6 hoursButton/Switch Power On/Off, Volume Up/Down, PTTLED indicators Power on: Flash blue twiceUnlink: Flash redLink: Flash bluePairing: Red and Blue blinkingBattery low: Flash red and bluePower off: Flash red 3 timesOperating temperature 32 °F to 104 °F (0 °C to 40 °C)Operating humidity 5 - 90 %Certification FCC, CE, BQBReplacement PartsExample:Use the “CAB-1” Example:Use the “CD-40”Ear hook ................. S8002323Ear hook sponge ..... S8002325Speaker sponge ....... S8002324Wind Screen ........... S8002322EAF44U760

Navigation menu