Yaesu Musen 20175X20 scanning receiver User Manual users manual
Yaesu Musen Co., Ltd. scanning receiver users manual
UserManual.wiki
>
Yaesu Musen
>
20175X20 User Manual
>
users manual
Contents
1.
users manual
2.
Operating Manual
users manual
Navigation menu
Upload a User Manual
Namespaces
Wiki Guide
HTML
PDF
Info
Views
User Manual
Discussion / Help
Navigation
![FCC ID: K6620175X20IC ID: 511B-20175X20Operating Manual 3/44Vertex Standard Co., Ltd.PTT (Push To Talk) SwitchPress this switch to transmit, and release it (to receive) after your transmission is completed.MONI SwitchPressing this switch disables the noise squelching action, allowing you to hear very weaksignals near the background noise level temporarily.Press the [F/W] key on the keypad first, then press this switch to “open” the squelchcontinuously. Press this switch again to resume normal (quiet) monitoring.LAMP SwitchPressing this switch illuminates the LCD and keypad for five seconds, after which the back-lighting will automatically turn off.Press the [F/W] key on the keypad first, then press this switch to activate the back-lightinglamp continuously. To turn the lamp off, press this switch again.You can change the primary (press key) function of this switch, if you prefer. See page ?? fordetails.KEYPADThese 16 keys select many of most important operating features on the FT-60R. Thefunctions of the keys are described in detail on the pages to follow.SPEAKERThe internal speaker is located here.MICThe internal microphone is located here.MIC/SP JackThis four-conductor miniature jack provides connection points for microphone audio,earphone audio, PTT, and ground.EXT DC JackThis coaxial DC jack allows connection to an external DC power source (6-16V DC). Thecenter pin of this jack is the Positive (+) connection.Keypad FunctionsKey Press Key Press [F/W] Key + Press and Hold Key[1(SQ TYP)] Frequency entry digit“1”Activates the CTCSSor DCS OperationRecalls the “Weather”broadcast channelbank[2(CODE)] Frequency entry digit“2”Selects the CTCSStone or DCS codenumberActivates the ARTSfeature[3(TX PO)] Frequency entry digit“3”Selects the desiredtransmit power outputlevelActivates the SmartSearch feature[UP(MHz)] Increases the VFOfrequency by one stepor moves the memorychannel to the next-highest channelTunes up the VFOfrequency in 1 MHzstepsStarts the scannerupward (toward ahigher frequency or ahigher channelnumber)[4(RPT)] Frequency entry digit Selects the direction of Activates the](https://usermanual.wiki/Yaesu-Musen/20175X20.users-manual/User-Guide-424512-Page-3.png)
![FCC ID: K6620175X20IC ID: 511B-20175X20Operating Manual 4/44Vertex Standard Co., Ltd.“4” the uplink frequencyshift (either “-,” “+,” or“simplex”) duringrepeater operationEMERGENCYfunction[5(BELL)] Frequency entry digit“5”Selects theCTCSS/DCS Bellringer repetitions--[6(LOCK)] Frequency entry digit“6”Activates the KeyLockout featureActivates the KeyLockout feature[DOWN(MHz)]Decreases the VFOfrequency by one stepor moves the memorychannel to the next-lowest channelTunes down the VFOfrequency in 1 MHzstepsStarts the scannerdownward (toward alower frequency or alower channel number)[7(P1)]*1Frequency entry digit“7”Activates the EPCS(Enhanced Paging &Code Squelch) feature--[8(P2)]*1Frequency entry digit“8”Selects the MemoryScan “Skip” channel-selection mode--[9(DTMF)] Frequency entry digit“9”Selects the DTMFmode--[HM/RV] *2Reverses the transmitand receivefrequencies whileworking through arepeaterSwitches to the“Home” (favoritefrequency) Channel--[V/M(PRI)] Switches thefrequency controlbetween the VFO andMemory SystemsActivates the Priority(Dual Watch) functionStarts theprogrammablescanner upward(toward a higherfrequency or a higherchannel number)[0(%)SET] Activates the InternetConnection featureFrequency entry digit“0”Engages the Set(Menu) Mode.Activates the InternetConnection featureand enables accesscode selection[BAND] Moves operation to thenext-highest frequencyband while in the VFOmodeActivates the “Memory“Tune” mode while inthe Memory RecallmodeMoves operation to thenext-lowest frequencybandSelects the bandwidthfor the programmablescanner while in theVFO modeFW Activates the“Alternate” keyfunction.Disables the“Alternate” keyfunction.Activates the “MemoryWrite” mode (formemory channelstorage).*1: You can program the alternate (Press [F/W] Key +) function of the key to another function,if desired. See page ?? for details.](https://usermanual.wiki/Yaesu-Musen/20175X20.users-manual/User-Guide-424512-Page-4.png)
![FCC ID: K6620175X20IC ID: 511B-20175X20Operating Manual 5/44Vertex Standard Co., Ltd.*2: You can exchange the function between primary (Press Key) function and alternate (Press[F/W] Key +) function, if desired. See page ?? for details.Installation of AccessoriesAntenna InstallationThe supplied antenna provides good results over the entire frequency range of thetransceiver. However, for enhanced base station medium-wave and shortwave reception,you may wish to connect an external (outside) antenna, as the supplied antenna is very smalland cannot be expected to provide high performance at these frequencies.To install the supplied antenna, hold the bottom end of the antenna, then screw it onto themating connector on the transceiver until it is snug. Do not over-tighten by use of extremeforce.Notes: Never transmit without having an antenna connected. When installing the supplied antenna, never hold the upper part of the antenna whilescrewing it onto the mating connector on the transceiver. If using an external antenna for transmission, ensure that the SWR presented to thetransceiver is 1.5:1 or lower, to avoid excessive feedline loss.Installation of FNB-83 Battery PackThe FNB-83 is a high-performance Ni-MH battery providing high capacity in a compactpackage. Under normal use, the FNB-83 may be used for approximately 300 charge cycles,after which operating time may be expected to decrease. If you have an old battery packwhich is displaying capacity which has become diminished, you should replace the pack witha new one.Installation of the battery is easy and quick: Insert the battery pack into the battery compartment on the back of the radio while tiltingthe Belt Clip outward, then close the Battery Pack Latch until it locks in place with a“Click.” To remove the battery, turn the radio off and remove any protective cases. Open theBattery Pack Latch on the bottom of the radio, then slide the battery downward and outfrom the radio while unfolding the Belt Clip.Battery ChargingIf the battery has never been used, or its charge is depleted, it may be charged by connectingthe NC-88 Overnight Battery Charger, as shown in the illustration, to the EXT DC jack. If only12 ~ 16 Volt DC power is available, the optional E-DC-5B DC Adapter (with its cigarettelighter plug) may also be used for charging the battery.A fully-discharged pack will be charged completely in 10 hours. Disconnect the NC-88 fromthe EXT DC jack and the AC line outlet.Important Note The NC-88 is not designed to power the transceiver for operation (reception ortransmission). Do not leave the NC-88 connected to the transceiver for continuous periods in excess of24 hours. Long term overcharging can degrade the Ni-MH battery pack and significantlyshorten its useful life. Please be advised that the NC-88 may contribute noise to TV and radio reception in theimmediate vicinity, so we do not recommend its use adjacent to such devices.](https://usermanual.wiki/Yaesu-Musen/20175X20.users-manual/User-Guide-424512-Page-5.png)
![FCC ID: K6620175X20IC ID: 511B-20175X20Operating Manual 7/44Vertex Standard Co., Ltd.Adjusting the Audio Volume Level and Squelch Setting At first, set the SQL knob fully counter-clockwise. Now, you may rotate the VOL/PWRknob to adjust the receiver level for a comfortable listing level, using the backgroundnoise as a reference. To set the squelch, turn the SQL knob clockwise, slightly past the point where thebackground noise is muted. This is the point of best sensitivity to weak signals, and werecommend that you not rotate the SQL knob very much past the point where thebackground noise is just silenced.R.F. Says: 1) A special “RF Squelch” feature is provided on this radio. This feature allows youto set the squelch so that only signals exceeding a certain S-meter level will open the squelch.See page ?? for details.2) If you’re operating in an area of high RF pollution, you may need to consider “ToneSquelch” operation using the built-in CTCSS Decoder. This feature will keep your radio quietuntil a call is received from a station sending a carrier which contains a matching (subaudible)CTCSS tone. Or, if your friends have radios equipped with DCS (Digital Coded Squelch) likeyour FT-60R has, try using that mode for silent monitoring of busy channels.Selecting the Operating Band Press the [BAND] key repetitively. You will see the LCD indication move toward a higherfrequency band each time you press the [BAND] key.850 MHz Æ 144 MHz Æ 250 MHz Æ 350 MHz Æ 430 MHz Æ 850 MHz …… If you wish to move the operating band selection downward (toward lower frequencyband), press the [F/W] key first, then press the [BAND] key.350 MHz Æ 250 MHz Æ 144 MHz Æ 850 MHz Æ 430 MHz Æ 350 MHz …… Once you have selected the desired band, you may initiate manual tuning (or scanning)per the discussion in the next chapter.Frequency NavigationThe FT-60R will initially be operating in the “VFO” mode, a channelized system which allowsfree tuning throughout the currently-selected operating band.Three basic frequency navigation methods are available on the FT-60R:1) Tuning DialRotation of the DIAL allows tuning in the pre-programmed steps established for the currentoperating band. Clockwise rotation of the DIAL causes the FT-60R to be tuned toward ahigher frequency, while counter-clockwise rotation will lower the operating frequency.If you press the [F/W] key momentarily, then rotate the DIAL, frequency steps of 1 MHz will beselected. This feature is extremely useful for making rapid frequency excursions over thewide tuning range of the FT-60R.2) Direct Keypad Frequency EntryThe desired operating frequency may be entered directly from the keypad.To enter a frequency from the keypad, just press the numbered digits on the keypad in theproper sequence. Examples:To enter 146.560 MHz, press [1] Æ [4] Æ [6] Æ [5] Æ [6] Æ [0]To enter 146.5625 MHz (in 12.5 kHz), [1] Æ [4] Æ [6] Æ [5] Æ [6] Æ [2]3) ScanningPress and hold in either the [UP] or [DOWN] key for one second to initiate upward ordownward scanning, respectively (Manual VFO Scan).](https://usermanual.wiki/Yaesu-Musen/20175X20.users-manual/User-Guide-424512-Page-7.png)
![FCC ID: K6620175X20IC ID: 511B-20175X20Operating Manual 8/44Vertex Standard Co., Ltd.For scanning within a limited sub-band range, from the VFO mode, press and hold in the[V/M(PRI)] key for one second to begin scanning toward a higher frequency within thepreviously-defined sub-band (Programmed VFO Scan). Details regarding sub-band setupmay be found on page ??.If you wish to reverse the direction of the scan (i.e. toward a lower frequency, instead of ahigher frequency), just rotate the DIAL one click in the counter-clockwise direction while theFT-60R is scanning. The scanning direction will be reversed. To revert to scanning toward ahigher frequency once more, rotate the DIAL one click clockwise.The scanner will stop when it receives a signal strong enough to break through the Squelchthreshold. The FT-60R will then hold on that frequency according to the setting of the“RESUME” mode (Set Mode Item 34: RESUME). Press the PTT switch momentarily tocancel the scanning. This only stops the scan; it does not cause transmission to occur. Seepage ?? for details regarding Scan Operation.TransmissionOnce you have set up an appropriate frequency inside one of the 144 MHz or 430 MHzAmateur bands on which the FT-60R can transmit, you’re ready to go on the air! These arethe most basic steps; more advanced aspects of transmitter operation will be discussed later. To transmit, press the PTT switch, and speak into the front panel microphone (located inthe lower left-hand corner of the speaker grille) in a normal voice level. The TX/BUSYindicator will glow red during transmission. To return to the receive mode, release the PTT switch. During transmission, the relative power level will be indicated on the bar graph at thebottom of the LCD; full scale deflection confirms “High Power” operation, while deflectionof two bars indicates “Low Power” operation or five bars indicates “Middle Power”operation. Additionally, the “LOW” icon will appear at the bottom of the display whileoperating on the “Low Power” and “Middle Power” settings.R.F. Says: 1) If you’re just talking to friends in the immediate area, you’ll get much longerbattery life by switching to Low Power operation, described next chapter. And don’t forget:always have an antenna connected when you transmit.2) Transmission is possible only on the 144 MHz and 430 MHz bands.Changing the Transmitter Power LevelTo change the power level: Press the [F/W] key, then press the [3(LOW)] key. The LCD shows the current poweroutput level. Rotate the DIAL knob to select the desired power output level. Available selections are“HIGH (5 W),” “MID (2 W),” and “LOW (0.5 W).” When you have made your choice, press the PTT switch to save the new setting andreturn to normal operation.R.F. Says: 1) The FT-60R is smart! You can set up Low power on the 144 MHz band, whileleaving 430 MHz on High power, and the radio will remember the different settings on bothbands. And when you store memories, you can store the power output settings separately ineach memory, so you don’t waste battery power when using very close-in repeaters!2) When you are operating on the “Low” or “Middle” power setting, you can press the [F/W]key, when press the PTT switch, to cause the FT-60R to transmit (temporarily) on High power.After one transmission, the power level will revert to the previously-selected (“Low” or“Middle” power) setting.](https://usermanual.wiki/Yaesu-Musen/20175X20.users-manual/User-Guide-424512-Page-8.png)
![FCC ID: K6620175X20IC ID: 511B-20175X20Operating Manual 9/44Vertex Standard Co., Ltd.Advanced OperationNow that you’re mastered the basics of FT-60R operation, let’s learn more about some of thereally neat features.Keyboard LockingIn order to prevent accidental frequency change or inadvertent transmission, various aspectsof the FT-60R’s DIAL and keypad may be locked out. The possible lockout combinations are:LK KEY: Just the front panel keypad is locked outLKDIAL: Just the top panel DIAL is locked outLK K+D: Both the keypad and DIAL are locked out (factory default)LK PTT: The PTT switch is locked out (TX not possible)LK P+K: Both the PTT switch and keypad are locked outLK P+D: Both the PTT switch and DIAL are locked outLK ALL: All of the above are locked outTo lock out some or all of the keys:1. Press the [F/W] key, then press the [%(0)SET] key to enter the Set mode.2. Rotate the DIAL knob to select Set Mode Item 25: LOCK.3. Press the [F/W] key momentarily to enable adjustment of this Item.4. Rotate the DIAL knob to choose between one of the locking schemes as outlined above.5. When you have made your selection, press the PTT switch to save the new setting andreturn to normal operation.To activate the locking feature, (1) press and hold in the [6(LOCK)] key for one second, or (2)press the [F/W] key, then press the [6(LOCK)] key. The “Key Lock” icon will appear on theLCD. To cancel locking, repeat this process.Keypad/LCD IlluminationYour FT-60R includes a reddish illumination lamp which aids in nighttime operation. Thereddish illumination yields clear viewing of the display in a dark environment, with minimaldegradation of your night vision.Three options for activating the lamp are provided:KEY Mode: Illuminates the Keypad/LCD lamp for five seconds when you rotate the DIALknob or press the keypad or any switch (except PTT switch). this is the factory-programmeddefault setting.5SEC Mode: Illuminates the Keypad/LCD lamp for five seconds when you press the LAMPswitch momentarily.TOGGLE Mode: Toggles the Keypad/LCD lamp on and off by pressing the LAMP switchmomentarily.Here is the procedure for setting up the Lamp operating mode:1. Press the [F/W] key, then press the [%(0)SET] key to enter the Set mode.2. Rotate the DIAL knob to select Set Mode Item 24: LAMP.3. Press the [F/W] key momentarily to enable adjustment of this Item.4. Rotate the DIAL knob to select one of the three modes described above.5. When you have made your choice, press the PTT switch to save the new setting andreturn to normal operation.R.F. Says: Press the [F/W] key first, then press the LAMP switch to illuminate theKeypad/LCD lamp continuously until you press the LAMP key again, irrespective of the Lampmode programmed per the above instructions.Disabling the Keypad BeeperA keypad beeper provides useful audible feed back whenever a keypad is pressed.](https://usermanual.wiki/Yaesu-Musen/20175X20.users-manual/User-Guide-424512-Page-9.png)
![FCC ID: K6620175X20IC ID: 511B-20175X20Operating Manual 10/44Vertex Standard Co., Ltd.If you want to turn the beep off:1. Press the [F/W] key, then press the [%(0)SET] key to enter the Set mode.2. Rotate the DIAL knob to select Set Mode Item 6: BEEP.3. Press the [F/W] key momentarily to enable adjustment of this Item.4. Rotate the DIAL knob to change the setting to “OFF.”5. Press the PTT switch to save the new setting and return to normal operation.6. To turn the beep back on again, select “KEY” or “KEY+SC (factory default)” in step 4above.KEY: The beeper sounds when you press the keypad.KEY+SC: The beeper sounds when you press the keypad, or when the scanner stops.RF SquelchA special RF Squelch feature is provided on this radio. This feature allows you to set thesquelch so that only signals exceeding a certain S-meter level will open the squelch.To set up the RF squelch circuit for operation, use the following procedure:1. Press the [F/W] key, then press the [%(0)SET] key to enter the Set mode.2. Rotate the DIAL knob to select Set Mode Item 36: RF SQL.3. Press the [F/W] key momentarily to enable adjustment of this Item.4. Rotate the DIAL knob to select the desired signal strength level for the squelch threshold(S-1, S-2, S-3, S-4, S-5, S-6, S-8, S-FULL, or OFF).5. Press the PTT switch to save the new setting and return to normal operation.Finally, rotate the SQL knob fully clockwise.Checking the Battery VoltageThe FT-60R’s microprocessor includes programming which will measure the current batteryvoltage.1. Press the [F/W] key, then press the [%(0)SET] key to enter the Set mode.2. Rotate the DIAL knob to select Set Mode Item 12: DC VLT.3. Press the [F/W] key momentarily to display the current DC voltage being supplied.4. Press the PTT switch to return to normal operation.Repeater OperationRepeater stations, usually located on mountaintops or other high locations, provide adramatic extension of the communication range for low-powered hand-held or mobiletransceivers. The FT-60R includes a number of features which make repeater operationsimple and enjoyable.Repeater ShiftsYour FT-60R has been configured, at the factory, for the repeater shifts customary in yourcountry. For the 144 MHz band shift will be 600 kHz; on the 430 MHz band, the shift may be1.6 MHz, 7.6 MHz, or 5 MHz (USA version).Depending on the part of the band in which you are operating, the repeater shift may beeither downward (–) or upward (+), and one of these icons will appear at the top of the LCDwhen repeater shifts have been enabled.Automatic Repeater Shift (ARS)The FT-60R provides a convenient Automatic Repeater Shift feature, which causes theappropriate repeater shift to be applied automatically whenever you tune into the designatedrepeater sub-bands in your country. These sub-bands are shown below.If the ARS feature does not appear to be working, you may have accidentally disabled it.](https://usermanual.wiki/Yaesu-Musen/20175X20.users-manual/User-Guide-424512-Page-10.png)
![FCC ID: K6620175X20IC ID: 511B-20175X20Operating Manual 11/44Vertex Standard Co., Ltd.To re-enable ARS:1. Press the [F/W] key, then press the [%(0)SET] key to enter the Set mode.2. Rotate the DIAL knob to select Set Mode Item 4: ARS.3. Press the [F/W] key momentarily to enable adjustment of this Item.4. Rotate the DIAL knob to select “ARS. ON.”5. When you have made your selection, press the PTT switch to save the new setting andreturn to normal operation.Manual Repeater Shift ActivationIf the ARS feature has been disabled, or if you need to set a repeater shift direction other thanthat established by the ARS, you may set the direction of the repeater shift manually.To do this:1. Press the [F/W] key, then press the [%(0)SET] key to enter the Set mode.2. Rotate the DIAL knob to select Set Mode Item 37: RPT.MOD.3. Press the [H/L] key momentarily to enable adjustment of this Item.4. Rotate the DIAL knob to select the desired shift among “RPT.–,” “RPT.+,” and“RPT.OFF.”5. When you have made your selection, press the PTT switch to save the new setting andreturn to normal operation.R. F. Says: If you make a change in the shift direction, but still have Automatic RepeaterShift still engaged (see previous section), when you change frequency (by rotating the DIALknob, for example) the ARS will over-ride your manual setting of the shift direction. TurnARS off if you do not wish this to happen.Changing the Default Repeater ShiftsIf you travel to a different region, you may need to change the default repeater shift so as toensure compatibility with local operating requirements.To do this, follow the procedure below:1. Set the FT-60R’s frequency to the band on which you wish to change the defaultrepeater shift (144 MHz or 430 MHz Amateur Band).2. Press the [F/W] key, then press the [%(0)SET] key to enter the Set mode.3. Rotate the DIAL knob to select Set Mode Item 44: SHIFT.4. Press the [F/W] key momentarily to enable adjustment of this Item.5. Rotate the DIAL knob to select the new repeater shift magnitude.6. When you have made your selection, press the PTT switch to save the new setting andreturn to normal operation.R.F. Says: If you just have one “odd” split that you need to program, don’t change the“default” repeated shifts using this Set Mode Item. Enter the transmit and receive frequenciesseparately, as shown on page ??.Checking the Repeater Uplink (Input) FrequencyIt often is helpful to be able to check the uplink (input) frequency of a repeater, to see if thecalling station is within direct (“Simplex”) range.To do this, just press the [HM/RV] key. You’ll notice that the display has shifted to the repeateruplink frequency. Press the [HM/RV] key again to cause operation to revert to normalmonitoring of the repeater downlink (output) frequency.R. F. Says: The configuration of this key may be set either to “RV” (for checking the inputfrequency of a repeater), or “HM” (for instant switching to the “Home” channel for the bandyou are operating on). To change the configuration of this key, use Set Mode Item 35:REV/HM. See page ??.](https://usermanual.wiki/Yaesu-Musen/20175X20.users-manual/User-Guide-424512-Page-11.png)
![FCC ID: K6620175X20IC ID: 511B-20175X20Operating Manual 12/44Vertex Standard Co., Ltd.CTCSS/DCS OperationCTCSS OperationMany repeater systems require that a very-low-frequency audio tone be superimposed onyour FM carrier in order to activate the repeater. This helps prevent false activation of therepeater by radar or spurious signals from other transmitters. This tone system, called“CTCSS” (Continuous Tone Coded Squelch System), is included in your FT-60R, and is veryeasy to activate.R.F. Says: CTCSS setup involves two actions: setting the Tone Mode and then setting of theTone Frequency. These actions are set up by using the [1(SQ TYP)] key and [2(CODE)] key.1. Press the [F/W] key, then press the [1(SQ TYP)] key to enable selection of theCTCSS/DCS mode.2. Rotate the DIAL knob so that “TONE” indication appears on the display; this activatesthe CTCSS Encoder, which allows repeater access.3. Rotation of the DIAL knob one more “click” in step “2” above will cause the “TSQL”notation to appear. When “TSQL” is displayed, this means that the Tone SQueLchsystem is active, which mutes your FT-60R’s receiver until it receives a call from anotherradio sending out a matching CTCSS tone. This can help keep your radio quiet until aspecific call is received, which may be helpful while operating in congested.R.F. Says: 1) You may notice “REV TN” indication on the display while you rotate theDIAL knob in this step; this means that the Reverse Tone Squelch system is active,which mutes your FT-60R’s receiver when it receives a call from the radio sending amatched CTCSS tone. The “TSQ” icon will blink on the display when the Reverse ToneSquelch system is activated.2) You may notice “DCS” indication on the display while you rotate the DIAL knob stillmore. We’ll discuss the Digital Code Squelch system shortly.4. When you have made your selection of the CTCSS tone mode, press the PTT switch tosave the new setting.5. Press the [F/W] key, then press the [2(CODE)] key to enable adjustment of the CTCSSfrequency.6. Rotate the DIAL knob until the display indicates the Tone Frequency you need to beusing (ask the repeater owner/operator if you don’t know the tone frequency).7. When you have made your selection, press the [F/W] key momentarily to save the newsettings and exit to normal operation. This is different than the usual method of restoringnormal operation, and it applies only to the configuration of the CTCSS/DCSfrequencies.R.F. Says: Your repeater may or may not re-transmit a CTCSS tone - some systems just useCTCSS to control access to the repeater, but don’t pass it along when transmitting. If the S-Meter deflects, but the FT-60R is not passing audio, repeat steps “1” through “4” above, butrotate the DIAL so that “TSQ” disappears - this will allow you to hear all traffic on the channelbeing received.DCS OperationAnother form of tone access control is Digital Code Squelch, or DCS. It is a newer, moreadvanced tone system which generally provides more immunity from false paging than doesCTCSS. The DCS Encoder/Decoder is built into your FT-60R, and operation is very similar tothat just described for CTCSS. Your repeater system may be configured for DCS; if not, DCSis frequently quite useful in Simplex operation if your friend(s) use transceivers equipped withthis advanced feature.R.F. Says: Just as in CTCSS operation, DCS requires that you set the Tone Mode to DCSand that you select a tone code.](https://usermanual.wiki/Yaesu-Musen/20175X20.users-manual/User-Guide-424512-Page-12.png)
![FCC ID: K6620175X20IC ID: 511B-20175X20Operating Manual 13/44Vertex Standard Co., Ltd.1. Press the [F/W] key, then press the [1(SQ TYP)] key to enable selection of theCTCSS/DCS mode.2. Rotate the DIAL knob until “DCS” indication appears on the display; this activates theDCS Encoder/Decoder.3. Press the PTT key to save the new setting.4. Press the [F/W] key, then press the [2(CODE)] key to enable adjustment of the DCScode.5. Rotate the DIAL knob to select the desired DCS Code (a three-digit number). Ask therepeater owner/operator if you don’t know DCS Code; if you are working simplex, justset up the DCS Code to be the same as that used by your friend(s).6. When you have made your selection, press the [F/W] key momentarily to save the newsettings and exit to normal operation.R.F. Says: Remember that the DCS is an Encode/Decode system, so your receiver willremain muted until a matching DCS code is received on an incoming transmission. Switchthe DCS off when you’re just tuning around the band!Tone Search ScanningIn operating situations where you don’t know the CTCSS or DCS tone being used by anotherstation or stations, you can command the radio to listen to the incoming signal and scan insearch of the tone being used. Two things must be remembered in this regard: You must be sure that your repeater uses the same tone type (CTCSS vs. DCS). Some repeaters do not pass the CTCSS tone; you may have to listen to the station(s)transmitting on the repeater uplink (input) frequency in order to allow Tone SearchScanning to work.To scan for the tone in use:1. Set the radio up for either CTCSS or DCS Decoder operation (see the previousdiscussions). In the case of CTCSS, “T SQ” will appear on the display; in the case ofDCS, “DCS” will appear on the display.2. Press the [F/W] key, then press the [2(CODE)] key.3. Press the [UP] or [DOWN] key to start scanning for the incoming CTCSS or DCStone/code.4. When the radio detects the correct tone or code, it will halt on that tone/code, and audiowill be allowed to pass. Press the [F/W] key to lock in that tone/code, then press the[F/W] key again to exit to normal operation.R.F. Says: If the Tone Scan feature does not detect a tone or code, it will continue to scanindefinitely. When this happens, it may be that the other station is not sending any tone. Youcan press the PTT switch to halt the scan at any time.You also can press the MONI key during Tone Scanning to listen to the (muted) signal fromthe other station. When you release the MONI key, Tone Scanning will resume after about asecond.Tone Scanning works either in the VFO or Memory modes.CTCSS/DCS Bell OperationDuring CTCSS Decode or DCS operation, you may set up the FT-60R such that a ringing“bell” sound alerts you to the fact that a call is coming in. Here is the procedure for activatingthe CTCSS/DCS Bell:1. Set the transceiver up for CTCSS Decode (“Tone Squelch”) or DCS operation, asdescribed previously.2. Adjust the operating frequency to the desired channel.3. Press the [F/W] key, then press the [5(BELL)] key.4. Rotate the DIAL knob to set the desired number of rings of the Bell. The available](https://usermanual.wiki/Yaesu-Musen/20175X20.users-manual/User-Guide-424512-Page-13.png)
![FCC ID: K6620175X20IC ID: 511B-20175X20Operating Manual 14/44Vertex Standard Co., Ltd.choices are “1 T,” “3 T,” “5 T,” or “8 T” rings, CONT (continuous ringing), or OFF.5. Press the PTT switch momentarily to save the new setting and exit to normal operation.When you are called by a station whose transceiver is sending a CTCSS tone or DCS codewhich matches that set into your Decoder, the Bell will ring in accordance with thisprogramming.Split Tone OperationThe FT-60R can be operated in a Split Tone configuration via the Set mode.1. Press the [F/W] key, then press the [%(0)SET] key to enter the Set mode.2. Rotate the DIAL knob to select Set Mode Item 46: SPLIT.3. Press the [F/W] key momentarily to enable adjustment of this Set Mode Item.4. Rotate the DIAL knob to select ON (to enable the Split Tone feature).5. Press the PTT key momentarily to save the new setting and exit to normal operation.When the Split Tone feature is activated, you can see the following additional parametersafter the “DCS” parameter while selecting the CTCSS type by pressing [F/W] Æ [1(SQ TYP)]:D: DCS Encode only(the “DCS” icon will blink during operation)T DCS: Encodes a CTCSS Tone and Decodes a DCS code(the “T” icon will blink and the “DCS” icon will appear during operation)D TSQL: Encodes a DCS code and Decodes a CTCSS Tone(the “TSQ” icon will appear and the “DCS” icon will blink during operation)Select the desired operating mode, from the selections shown above.Tone Calling (1750 Hz)If the repeaters in your country require a 1750-Hz burst tone for access (typically in Europe),you can set the MONI key to serve as a “Tone Call” switch instead. To change theconfiguration of this switch, we again use the Set Mode to help us.1. Press the [F/W] key, then press the [%(0)SET] key to enter the Set mode.2. Rotate the DIAL knob to select Set Mode Item 26: M/T-CL.3. Press the [F/W] key momentarily to enable adjustment of this Set Mode Item.4. Rotate the DIAL knob to select “TCALL” on the display.5. Press the PTT switch to save the new setting and exit to normal operation.To access a repeater, press and hold in the MONI key for the amount of time specified by therepeater owner/operator. The transmitter will automatically be activated, and a 1750-Hzaudio tone will be superimposed on the carrier. Once access to the repeater has been gained,you may release the MONI key, and use the PTT key for activating the transmitter thereafter.Memory ModeThe FT-60R provides a wide variety of memory system resources. These include:• 1000 “Standard” memory channels, numbered “000” through “999.”• 5 “Home” channels, providing storage and quick recall of one prime frequency oneach operating band.• 50 sets of band-edge memories, also known as “Programmable Memory Scan”channels, labeled “L01/U01” through “L50/U50.”• 10 Memory Banks, labeled “BANK 1” through “BANK10.” Each Memory Bank can beassigned up to 1000 channels from the “standard” and “PMS” memory channels.• 10 “Weather Broadcast” Channels.Memory Storage1. Select the desired frequency, while operating in the VFO mode. Be sure to set up anydesired CTCSS or DCS tones, as well as any desired repeater offset. The power level](https://usermanual.wiki/Yaesu-Musen/20175X20.users-manual/User-Guide-424512-Page-14.png)
![FCC ID: K6620175X20IC ID: 511B-20175X20Operating Manual 15/44Vertex Standard Co., Ltd.may also be set at this time, if you wish to store it.2. Press and hold in the [F/W] key for one second.3. Within five seconds of releasing the [F/W] key, you need to make a decision regardingchannel storage. The microprocessor will automatically select the next-available “free”channel (a memory register on which no data has been stored), so you may not wish tomake any change; if this is the case, proceed to step 4. If you wish to select a differentchannel number into which to store the data, rotate the DIAL knob to select the desiredmemory channel. You may jump 100 memory channels, if you’re in a hurry (101 Æ 201Æ 301 …) by pressing the [BAND(BAND DN)] key (multiple times, if necessary).4. Press the [F/W] key once more to store the frequency into memory.5. You still will be operating in the “VFO” mode, so you may now enter other frequencies,and store them into additional memory locations, by repeating the above process.Storing Independent Transmit Frequencies (“Odd Splits”)All memories can store an independent transmit frequency, for operation on repeaters withnon-standard shift. To do this:1. Store the receive frequency using the method already described under MEMORYSTORAGE (it doesn’t matter if a repeater offset is active).2. Turn to the desired transmit frequency, then press and hold in the [F/W] key for onesecond.3. Within five seconds of releasing the [F/W] key, rotate the DIAL knob to select the samememory channel number as used in step “1” above.4. Press and hold in the PTT switch, then press the [F/W] key once more momentarily whileholding the PTT switch in (this does not key the transmitter).R.F. Says: Whenever you recall a memory which contains independently-stored transmit andreceive frequencies, the “–+” indication will appear in the display.Memory Recall1. While operating in the VFO mode, press the [V/M(PRI)] key to enter the Memory mode.2. Rotate the DIAL knob to select the desired channel.3. To return to the VFO mode, press the [V/M(PRI)] key.R.F. Says: When the radio is already set to the Memory mode, an easy way to recallmemories is to key in the memory channel number, then press the [F/W] key.For example, to recall memory channel #14, press [1(SQ TYP)] Æ [4(RPT)] Æ [F/W].You may also recall the Programmable Memory channels (“L01/U01” through “L50/U50.”)using the following numbers: Programmable Memory channel #L1 = “1001,” U1 = “1002,” L50= “1099,” and U50 = “1100.”HOME Channel MemoryA special one-touch “HOME” channel is available for each of operating bands, to allow quickrecall of a favorite operating frequency on each band.Home Channel storage is simple to accomplish:1. Change the setting of the Set Mode Item 35: REV/HM from “REV” to “HOME,” if it is notalready set to the option (see page ??).2. Select the desired frequency, while operating in the VFO mode. Be sure to set up anydesired CTCSS or DCS tones, as well as any desired repeater offset. The power levelmay also be set at this time, if you wish to store it.3. Press and hold in the [F/W] key for one second.4. While the memory channel number is blinking, just press the [HM/RV] key. Thefrequency and other data (if any) will now be stored in the special HOME channelregister.5. You may repeat this process on the other operating bands.6. To recall the HOME channel, press the [HM/RV] key momentarily while operating either](https://usermanual.wiki/Yaesu-Musen/20175X20.users-manual/User-Guide-424512-Page-15.png)
![FCC ID: K6620175X20IC ID: 511B-20175X20Operating Manual 16/44Vertex Standard Co., Ltd.in the VFO or MR mode.R.F. Says: The UHF HOME channel is the one used during “Emergency” operation. Seepage ?? for details regarding this feature.Default Home ChannelsBAND FREQUENCY144 MHz Ham Band 146.520 MHz250 MHz Band 250.000 MHz350 MHz Band 350.000 MHz430 MHz Ham Band 446.000 MHz850 MHz Band 850.000 MHzLabeling MemoriesYou may wish to append an alpha-numeric “Tag” (label) to a memory or memories, to aid inrecollection of the channel’s use (such as a club name, etc.). This is easily accomplishedusing the Set Mode.1. Recall the memory channel on which you wish to append a label.2. Press the [F/W] key, then press the [%(0)SET] key to enter the Set mode.3. Rotate the DIAL knob to select Set Mode Item 28: NM WRT.4. Press the [F/W] key momentarily to display the previously stored label (if any).5. Press the [F/W] key again to clear any previous label.6. Rotate the DIAL knob to select the first digit of the desired label.7. Press the [F/W] key to move to the next character.8. If you make a mistake, press the [DOWN] key to back-space the cursor, then re-enterthe correct letter, number, or symbol.9. Repeat steps 5 through 7 to program the remaining letters, numbers, or symbols of thedesired label. A total of six characters may be used in the creation of a label.10. When you have programmed a label which is under 6 characters, press and hold in the[F/W] key for one second to confirm the label (if the label is exactly 6 characters in length,you do not need to press and hold in [F/W]).11. When you have completed the creation of the label, press the PTT key to save the labeland exit.To display the alpha-numeric “Tag” (label):1. Set the FT-60R to the “MR” (Memory Recall) mode, and recall the memory channel onwhich you wish to display its label.2. Press the [F/W] key, then press the [%(0)SET] key to enter the Set mode.3. Rotate the DIAL knob to select the Set Mode Item labeled 27: NAME.4. Press the [F/W] key momentarily to enable adjustment of this Item’s setting.5. Rotate the DIAL knob to set this Set Mode Item to “ALPHA” (thus enabling the alpha-numeric display).6. Press the PTT key to save the new setting and activate the alpha-numeric Tag.To disable the alpha-numeric Tag (enabling the frequency display), just repeat the aboveprocedure, rotating the DIAL knob to select “FREQ” in step 5 above.R. F. Says: You may set up some memory channels to have their frequencies displayed,while others may be set to have their Name Tag displayed; the selection within Set Mode Item27 is not applied to all memory channels at once (just the channel on which you currently areoperating).Memory Offset TuningOnce you have recalled a particular memory channel, you may easily tune off that channel,as though you were in the “VFO” mode.1. With the FT-60R in the “MR” (Memory Recall) mode, select the desired memorychannel.](https://usermanual.wiki/Yaesu-Musen/20175X20.users-manual/User-Guide-424512-Page-16.png)
![FCC ID: K6620175X20IC ID: 511B-20175X20Operating Manual 17/44Vertex Standard Co., Ltd.2. Press the [BAND(BAND DN)] key momentarily to activate the “Memory Tuning” feature.The Memory Channel number will be replaced by “tun.”3. Rotate the DIAL knob, as desired, to tune to a new frequency. The synthesizer stepsselected for VFO operation on the current band will be the steps used during MemoryTuning.4. If you wish to return to the original memory frequency, just press the [BAND(BAND DN)]key momentarily.5. If you wish to store a new frequency set during Memory Tuning, just press and hold inthe [F/W] key for one second, per normal memory storage procedure. Themicroprocessor will automatically set itself to the next-available clear memory location,and you then press [F/W] again to lock in the new frequency.R.F. Says: 1) If you want to replace the original memory contents with those of the newfrequency, be sure to rotate the DIAL knob to the original memory channel number!2) Any required CTCSS/DCS changes, or repeater offset modifications, must be done beforestoring the data into the new (or original) memory channel location.Deleting MemoriesYou may desire to delete the memories (except the Memory Channel “1” and Home Channel).The procedure for deleting a channel is quite simple.1. Press the [V/M(PRI)] key, if needed, to enter the MR mode.2. Press and hold in the [F/W] key for one second, then rotate the DIAL knob to select thememory channel to be “deleted.”3. Press the [HM/RV] key momentarily. The display will revert to memory channel #1. Thepreviously-selected memory will be deleted.R.F. Says: Important Notice! Once deleted, the channel data cannot be recovered!Memory Bank OperationThe large number of memories available in the FT-60R could be difficult to utilize withoutsome means of organizing them. Fortunately, the FT-60R includes provision for dividing thememories into as many as ten Memory Groups, so you can categorize the memories in amanner convenient to you. You may enter and exit the “Memory Group” mode by a singlepress of the [BAND] key, as we shall see below.Assigning Memories to a Memory Bank1. Recall the memory channel to be assigned to a Memory Bank.2. Press and hold in the [BAND(BAND DN)] key for one second, then rotate the DIAL knobto select the Memory Bank number you want as the Memory Bank for this channel(“BANK 1” ~ “BANK10”).3. Press and hold the [F/W] key for one second to copy the memory channel data into theMemory Bank.Memory Bank Recall1. Press the [V/M(PRI)] key, if needed, to enter the Memory mode.2. Press and hold in the [BAND(BAND DN)] key, then rotate the DIAL knob to select thedesired Memory Bank (“BANK 1” through “BANK10”).3. Press the [V/M(PRI)] key momentarily; now, as you rotate the DIAL knob to selectmemories, you will observe that you can only select memory channels in the currentmemory bank. The “BANK” indication will appear at the left side of the frequency displaywhile operating in the Memory Bank.4. To change to another Memory Bank, press and hold in the [BAND(BAND DN)] key,rotate the DIAL knob to select the new Memory Bank, then press the [V/M(PRI)] keymomentarily.5. To exit from Memory Bank operation, select “NOBANK” in step 4 above. You are now inthe “standard” Memory Recall mode, without utilization of the Memory Banks. The](https://usermanual.wiki/Yaesu-Musen/20175X20.users-manual/User-Guide-424512-Page-17.png)
![FCC ID: K6620175X20IC ID: 511B-20175X20Operating Manual 18/44Vertex Standard Co., Ltd.memories stored in the various Banks will remain in those banks, however; you do notneed to store them again.Moving Memory Data to the VFOData stored on memory channels can easily be moved to the VFO, if you like.1. Select the memory channel containing the frequency data to be moved to the VFO.2. Press the [BAND(BAND DN)] key momentarily to activate the “Memory Tune” featuretemporarily, then press and hold in the [BAND(BAND DN)] key for one second. The datawill now have been copied to the VFO, although the original memory contents willremain intact on the previously-stored channel.R.F. Says: If a Split Frequency Memory channel was transferred, the TX frequency will beignored (you will be set up for Simplex operation on the Receive frequency).Memory Only ModeOnce memory channel programming has been completed, you may place the radio in a“Memory Only” mode, whereby VFO operation is impossible. This may be particularly usefulduring public-service events, where a number of operators may be using the radio for firsttime, and ultimate simplicity of channel selection is desired.To place the radio into the Memory Only mode:1. Turn the radio off.2. Press and hold in the MONI switch (just below the PTT switch) while turning the radio on.3. Rotate the DIAL knob to select the “F5 M-ONLY” option, then press the [F/W] key.To return to normal operation, repeat the above power-on procedure.Weather Broadcast Channels (U. S. Version)The VHF Weather Broadcast Station Memory Channel Bank has been pre-programmed atthe factory, for quick selection of NOAA weather information stations.1. Press and hold in the [1(SQ TYP)] key for one second to recall the Weather BroadcastMemory Bank.2. Rotate the DIAL knob to select the desired Weather Broadcast channel.3. If you wish to scan this bank to search for louder stations, just press the PTT switch.When the scanner pauses on a station, press the PTT key once to halt the scan, or pressit twice to restart the scan.4. To exit to normal operation, press the [V/M(PRI)] key, or press and hold in the [1(SQTYP)] key again.Severe Weather AlertIn the event of extreme weather disturbances, such as severe thunderstorms and hurricanes,the NOAA (National Oceanic and Atmospheric Administration) sends a weather alertaccompanied by a 1050 Hz tone and subsequent weather report on one of the NOAAweather channels.ScanningThe FT-60R allows you to scan just the memory channels, the entire operating band, or aportion of that band. It will halt on signals encountered, so you can talk to the station(s) onthat frequency, if you like.Scanning operation is basically the same in each of the above modes. Before you begin, takea moment to select the way in which you would like the scanner to resume scanning after ithalts on a signal.](https://usermanual.wiki/Yaesu-Musen/20175X20.users-manual/User-Guide-424512-Page-18.png)
![FCC ID: K6620175X20IC ID: 511B-20175X20Operating Manual 19/44Vertex Standard Co., Ltd.Setting the Scan-Resume TechniqueThree options for the Scan-Resume mode are available:BUSY: In this mode, the scanner will halt on a signal it encounters. Two seconds after thecarrier has dropped because the other station(s) ceased transmission, the scanner willresume. In the case of constant-carrier signals like Weather Station broadcasts, the scannerwill likely remain on this frequency indefinitely.HOLD: In this mode, the scanner will halt on a signal it encounters. It will not restartautomatically; you must manually re-initiate scanning if you wish to resume.TIME: In this mode, the scanner will halt on a signal it encounters, and will hold there for fiveseconds. If you do not take action to disable the scanner within that time period, the scannerwill resume even if the stations are still active.To set the Scan-Resume mode:1. Press the [F/W] key, then press the [%(0)SET] key to enter the Set mode.2. Rotate the DIAL knob to select Set Mode Item 34: RESUME.3. Press the [F/W] key momentarily to enable adjustment of this Set Mode Item.4. Rotate the DIAL knob to select the desired scan-resume mode.5. When you have made your selection, press the PTT key to save the new setting and exitto normal operation.R.F. Says: The default condition for this Set Mode Item is “BUSY.”VFO ScanningThe FT-60R provides two VFO scanning functions: “Manual VFO Scanning” and“Programmed VFO Scanning.”Manual VFO Scan1. Select the VFO mode by pressing the [V/M(PRI)] key, if necessary.2. Press and hold in either the [UP] or [DOWN] key for one second to initiate upward ordownward scanning, respectively.3. If and when the scanner encounters a signal strong enough to open the squelch, thescanner will halt temporarily; the decimal point of the frequency display will blink duringthis “Pause” condition.4. The scanner will then resume according to the Scan-Resume mode selected in theprevious section.5. To cancel scanning, press the PTT switch or [V/M(PRI)] key.Programmed VFO Scan1. Select the VFO mode by pressing the [V/M(PRI)] key, if necessary.2. Press and hold in the [BAND(BAND DN)] key for one second, then rotate the DIAL knobto select the bandwidth for the Programmed VFO scanner. Available selections are ±1MHz, ±2 MHz, ±5 MHz, ALL, PMS-X, and BAND.ALL: The scanner will sweep all frequencies.PMS-X: The scanner will sweep frequencies within the currently-selected PMSfrequency pair. See page ?? for details.BAND: The scanner will sweep frequencies only on the current band.3. Press the [BAND(BAND DN)] key momentarily to save the new setting and exit tonormal operation.4. Press and hold in the [V/M(PRI)] key for one second to start scanning.5. If and when the scanner encounters a signal strong enough to open the squelch, thescanner will halt temporarily; the decimal point of the frequency display will blink duringthis “Pause” condition.6. The scanner will then resume according to the Scan-Resume mode selected in theprevious section.7. To cancel scanning, press the PTT switch or [V/M(PRI)] key.](https://usermanual.wiki/Yaesu-Musen/20175X20.users-manual/User-Guide-424512-Page-19.png)
![FCC ID: K6620175X20IC ID: 511B-20175X20Operating Manual 20/44Vertex Standard Co., Ltd.R.F. Says: 1) When you start the Programmed VFO Scanner, the FT-60R will be changingfrequency in the upward direction. If you want to change direction of the scan while it isunderway, rotate the DIAL knob one click in the opposite direction (in this case, one clickcounter-clockwise). You’ll see the scanner turn around and change frequency downward!2) You may change the scanner’s method of operation so that the VFO frequency will jump tothe low band edge of the next band when the VFO frequency reaches the high edge of thecurrent band (or vice versa). See page ?? regarding Set Mode Item 53: VFO .BND.Memory ScanningMemory scanning is similarly easy to initiate:1. Select the Memory mode by pressing the [V/M(PRI)] key, if necessary.2. Press and hold in either the [UP] or [DOWN] key for one second to initiate upward ordownward scanning, respectively.3. If and when the scanner encounters a signal strong enough to open the squelch, thescanner will halt temporarily; the decimal point of the frequency display will blink duringthis “Pause” condition.4. The scanner will then resume according to the Scan-Resume mode selected in theprevious section.5. To cancel scanning, press the PTT switch or [V/M(PRI)] key.How to Skip (Omit) a Channel during Memory Scan OperationAs mentioned previously, some continuous-carrier stations like a Weather Broadcast stationwill seriously impede scanner operation if you are using the “Carrier Drop” Scan-Resumemode, as the incoming signal will not pause long enough for the transceiver to resumescanning. Such channels may be “Skipped” during scanning, if you like:1. Recall the Memory Channel to be skipped during scanning.2. Press the [F/W] key, then press the [%(0)SET] key to enter the Set mode.3. Rotate the DIAL knob to select the Set Mode Item 45: SKIP.4. Press the [F/W] key momentarily to enable adjustment of this Set Mode Item.5. Rotate the DIAL knob so as to select “SKIP.” The current Memory Channel will now beignored during scanning. The “ONLY” selection is used for “Preferential Memory Scan,”described in the next section.6. When you have made your selection, press the PTT key to save the setting and exit tonormal operation.When you recall the “skipped” memory channel manually, a small “” icon will appear at theleft of the memory channel number, indicating it is to be ignored during scanning.To re-institute a channel into the scanning loop, select “OFF” in step 5 above (the “Skipped”channel will, of course, still be accessible via manual channel selection methods using theDIAL knob in the MR mode, whether or not it is locked out of the scanning loop).R.F. Says: In the factory default configuration, you may recall Set Mode Item 45: SKIP bypressing [F/W] Æ [8(P2)].Preferential Memory ScanThe FT-60R also allows you to set up a “Preferential Scan List” of channels which you can“flag” within the memory system. These channels are designated by a blinking “” icon whenyou have selected them, one by one, for the Preferential Scan List.When you initiate memory scanning, beginning on a channel with the blinking “” iconappended, only those channels bearing the blinking “” icon will be scanned. If you initiatescanning on a channel which does not have the blinking “” icon appended, you will scan allchannels including those with the blinking “” icon appended.Here is the procedure for setting up and using the Preferential Scan List:1. Recall the Memory Channel which you wish to add to the Preferential Scan List.](https://usermanual.wiki/Yaesu-Musen/20175X20.users-manual/User-Guide-424512-Page-20.png)
![FCC ID: K6620175X20IC ID: 511B-20175X20Operating Manual 21/44Vertex Standard Co., Ltd.2. Press the [F/W] key, then press the [%(0)SET] key to enter the Set mode.3. Rotate the DIAL knob to select Set Mode Item 45: SKIP.4. Press the [F/W] key momentarily to enable adjustment of this Set Mode Item.5. Rotate the DIAL knob so as to select “ONLY.”6. When you have made your selection, press the PTT key to save the settings and exit tonormal operation.7. To remove a channel from the Preferential Scan List, just repeat the above procedure,rotating the DIAL knob to select “OFF” in step 5 above.R.F. Says: In the factory default configuration, you may recall Set Mode Item 45: SKIP bypressing [F/W] Æ [8(P2)].To initiate Preferential Memory Scan:1. Press the [F/W] key, then press the [%(0)SET] key to enter the Set mode.2. Rotate the DIAL knob to select Set Mode Item 42: SCN MD.3. Press the [F/W] key momentarily to enable adjustment of this Set Mode Item.4. Rotate the DIAL knob so as to select “ONLY.”5. Press the PTT key to save the settings and exit to normal operation.6. Now, press and hold in either the [UP] or [DOWN] key for one second to initiate thePreferential Memory Scan. Only the channels which have the blinking “” iconappended to the channel number will be scanned.7. To cancel the Preferential Memory Scan, just repeat the above procedure, rotating theDIAL knob to select “MEM” in step 4 aboveMemory Bank ScanWhen the Memory Bank feature is engaged, the scanner sweeps only memory channels inthe current Memory Bank. However, if the Memory Bank Link Scan feature is enabled, youmay sweep the memory channels in several Memory Banks which you have selected.To enable the Memory Bank Link Scan feature:1. Set the radio to the Memory mode by pressing the [V/M(PRI)] key, if necessary.2. Press and hold in the [BAND(BAND DN)] key for one second, then rotate the DIAL knobto select the first Memory Bank (“BANK 1” ~ “BANK10”) you wish to sweep usingMemory Bank Link Scan.3. Press the [F/W] key momentarily. The current Memory Bank will now be swept duringMemory Bank Scan. A “decimal point” will be appended between the “N” and “K” of theMemory Bank number indication (such as BAN.K 2).4. Repeat steps 2 and 3 above, to append the “decimal point” to any other Memory Banksyou wish to sweep.5. Now, press and hold in the [V/M(PRI)] key for one second to initiate the Memory BankLink Scan.6. To remove a Memory Bank from the Memory Bank Link Scan, repeat steps 2 and 3above, to delete the “decimal point” from the Memory Bank number indication.Weather Alert ScanThis feature allows you to check a Weather Broadcast Memory Channel while operatingusing VFO scan or Memory channel scan.When the Weather Alert Scan feature is engaged, the FT-600R will check the WeatherBroadcast Memory Channels for activity every five seconds while scanning.To enable the Weather Alert Scan feature:1. Press the [F/W] key, then press the [%(0)SET] key to enter the Set mode.2. Rotate the DIAL knob to select Set Mode Item 55: WX ALT.3. Press the [F/W] key momentarily to enable adjustment of this Set Mode Item.](https://usermanual.wiki/Yaesu-Musen/20175X20.users-manual/User-Guide-424512-Page-21.png)
![FCC ID: K6620175X20IC ID: 511B-20175X20Operating Manual 22/44Vertex Standard Co., Ltd.4. Rotate the DIAL knob so as to select “ALT. ON.”5. When you have made your selection, press the PTT key to save the setting and exit tonormal operation.6. To disable the Weather Alert Scan feature, select “ALT.OFF” in step 4 above.R.F. Says: When the Weather Alert Scan feature is engaged, the Scan-Resume mode isfixed to “TIME.”Programmable (Band Limit) Memory Scan (PMS)This feature allows you to set sub-band limits for either scanning or manual VFO operation.For example, you might wish to set up a limit (in North America) of 144.300 MHz to 148.000MHz so as to prevent encroachment into the SSB/CW “Weak Signal” portion of the bandbelow 144.300 MHz. Here’s how to do this:1. Set the radio to the VFO mode by pressing the [V/M(PRI)] key, if necessary.2. Using the techniques learned earlier, store (per the above concept) 144.300 MHz intoMemory Channel #L01 (the “L” designates the Lower sub-band limit).3. Likewise, store 148.000 MHz into Memory Channel #U01 (the “U” designates the Uppersub-band limit).4. Confirm the radio is in the VFO mode, press and hold in the [BAND(BAND DN)] key forone second, and rotate the DIAL knob to select the desired PMS frequency pair (PMSxx),then press the [BAND(BAND DN)] key.5. Now, press and hold in the [V/M(PRI)] key for one second to initiate the Programmable(Band Limit) Memory Scan; the Memory Channel number will be replaced by “Pxx.”Scanning and tuning will now be limited within the just-programmed range.6. 50 pairs of Band Limit memories, labeled L01/U01 through L50/U50 are available. Youtherefore can set upper and lower operation limits on a number of bands, if you like.Priority Channel” Scanning (Dual Watch)The FT-60R’s scanning features include a two-channel scanning capability which allows youto operate on a VFO or Memory channel, while periodically checking a user-defined MemoryChannel for activity. If a station is received on the Memory Channel which is strong enough toopen the Squelch, the scanner will pause on that station in accordance with the Scan-Resume mode set via Set Mode Item 34: RESUME. See page ??.Here is the procedure for activating Priority Channel Dual Watch operation:VFO Priority1. Recall the memory channel you wish to use as the “Priority” frequency.2. Now, set the radio to the VFO mode by pressing the [V/M(PRI)] key.3. Press the [F/W] key, then press the [V/M(PRI)] key to activate the VFO Priority mode.The display will remain on the VFO frequency, but every five seconds the radio will checkthe Priority Channel (memory channel) for activity.4. Press [F/W] Æ [V/M(PRI)] again to disable the VFO Priority mode.Memory Channel Priority1. Store the frequency you wish to be the “Priority” Channel into memory channel “1.”2. Now, set the radio for operation on another memory channel.3. Press the [F/W] key, then press the [V/M(PRI)] key to activate the Memory Priority mode.The display will remain on the current memory channel frequency, but every fiveseconds the radio will check the Priority Channel (memory channel “1”) for activity.4. Press [F/W] Æ [V/M(PRI)] again to disable the Memory Priority mode.When the Memory Bank feature is activated, the FT-60R will check the lowest memorychannel in the current Memory Bank as the priority channel.HOME Channel Priority1. Recall the memory channel you wish to use as the “Priority” frequency.](https://usermanual.wiki/Yaesu-Musen/20175X20.users-manual/User-Guide-424512-Page-22.png)
![FCC ID: K6620175X20IC ID: 511B-20175X20Operating Manual 23/44Vertex Standard Co., Ltd.2. Now set the radio for operation on a HOME channel by pressing the [F/W] key followedby [HM/RV].3. Press the [F/W] key, then press the [V/M(PRI)] key to activate the HOME Priority mode.The display will remain on the HOME channel frequency, but every five seconds theradio will check the Priority Channel (memory channel) for activity.4. Press [F/W] Æ [V/M(PRI)] again to disable the HOME Priority mode.WX Channel Priority1. Recall the memory channel you wish to use as the “Priority” frequency.2. Now, set the radio for operation on a WX channel by pressing and holding in the [1(SQTYP)] key for one second.3. Press the [F/W] key, then press the [V/M(PRI)] key to activate the WX Priority mode. Thedisplay will remain on the WX channel frequency, but every five seconds the radio willcheck the Priority Channel (memory channel) for activity.4. Press [F/W] Æ [V/M(PRI)] again to disable the WX Priority mode.Priority Revert ModeDuring Priority channel operation (Dual Watch), a special feature is available which will allowyou to move to the Priority channel instantly, without waiting for activity to appear on thePriority channel.When this feature is enabled, and Priority monitoring is engaged, just press the PTT switch;operation will instantly revert to the Priority channel.To enable the Priority Revert operation:1. Press the [F/W] key, then press the [%(0)SET] key to enter the Set mode.2. Rotate the DIAL knob to select Set Mode Item 38: PRI.RVT.3. Press the [F/W] key momentarily to enable adjustment of this Set Mode Item.4. Rotate the DIAL knob to set this Set Mode Item to “RVT. ON.”5. When you have made your selection, press the PTT key to save the setting and exit tonormal operation.6. To disable the Priority Revert operation, just repeat the above procedure, rotating theDIAL knob to select “RVT.OFF” in step 4 above.Automatic Lamp Illumination on Scan StopThe FT-60R will automatically illuminate the LCD/Keypad Lamp whenever the scanner stopson a signal; this allows you to see the frequency of the incoming signal better at night. Notethat this will, of course, increase the battery consumption, so be sure to switch it off during theday (the default condition for this feature is “ON”).The procedure for disabling the Scan Lamp is:1. Press the [F/W] key, then press the [%(0)SET] key to enter the Set mode.2. Rotate the DIAL knob to select Set Mode Item 43: SCN.LMP.3. Press the [F/W] key momentarily to enable adjustment of this Set Mode Item.4. Rotate the DIAL knob to set this Set Mode Item to “OFF.”5. When you have made your selection, press the PTT key to save the setting and exit tonormal operation.Band Edge BeeperThe FT-60R will automatically when a band edge is encountered during scanning (either instandard VFO scanning or during PMS operation). You may also enable this feature (bandedge beeper) to operate when the frequency reaches the band edge while selecting the VFOfrequency using the DIAL knob.The procedure for enabling the Band-Edge Beeper is:](https://usermanual.wiki/Yaesu-Musen/20175X20.users-manual/User-Guide-424512-Page-23.png)
![FCC ID: K6620175X20IC ID: 511B-20175X20Operating Manual 24/44Vertex Standard Co., Ltd.1. Press the [F/W] key, then press the [%(0)SET] key to enter the Set mode.2. Rotate the DIAL knob to select Set Mode Item 18: EDG.BEP.3. Press the [F/W] key momentarily to enable adjustment of this Set Mode Item.4. Rotate the DIAL knob to set this Set Mode Item to “BEP. ON.”5. When you have made your selection, press the PTT key to save the setting and exit tonormal operation.EPCS (Enhanced Paging & Code Squelch)The FT-60R includes an Enhanced CTCSS tone encoder/decoder and a dedicatedmicroprocessor providing paging and selective calling feature. This allows you to place a callto a specific station (Paging), and to receive calls of your choice directed only to you (CodeSquelch).The paging and code squelch systems use an (alternately switched) CTCSS tone pair whichis stored in the Pager Memory. Basically, your receiver remains silent until it receives theCTCSS tone pair that matches those stored in the Pager Memory. The squelch then opensso the caller is heard, and the paging ringer immediately sounds, if activated. When you closethe PTT switch to transmit, the same stored CTCSS tone pair will be transmittedautomatically.Storing the CTCSS Tone Pair for EPCS Operation1. Press the [F/W] key, then press the [%(0)SET] key to enter the Set mode.2. Rotate the DIAL knob to select Set Mode Item 30: PAG.COD.3. Press the [F/W] key momentarily to enable adjustment of this Set Mode Item.4. Rotate the DIAL knob to set the CTCSS Tone number which corresponds tothe first toneof the CTCSS Tone Pair.5. Press the [UP] or [DOWN] key, then rotate the DIAL knob to set the CTCSS Tonenumber which corresponds to the second tone of the CTCSS Tone Pair.6. Press the PTT switch to save the new setting and exit to normal operation.CTCSS Tone Number01 67.0 11 94.8 21 131.8 31 171.3 41 203.502 69.3 12 97.4 22 136.5 32 173.8 42 206.503 71.9 13 100.0 23 141.3 33 177.3 43 210.704 74.4 14 103.5 24 146.2 34 179.9 44 218.105 77.0 15 107.2 25 151.4 35 183.5 45 225.706 79.7 16 110.9 26 156.7 36 186.2 46 229.107 82.5 17 114.8 27 159.8 37 189.9 47 233.608 85.4 18 118.8 28 162.2 38 192.8 48 241.809 88.5 19 123.0 29 165.5 39 196.6 49 250.310 91.5 20 127.3 30 167.9 40 199.5 50 251.4R.F. Says: The FT-60R does not recognize the order of the 1st tone and the 2nd tone. Inother words, for example, the FT-60R considers both CTCSS pairs “10, 35” and “35, 10” to beidentical.Activating the Enhanced Paging & Code Squelch System1. Press the [F/W] key, then press the [%(0)SET] key to enter the Set mode.2. Rotate the DIAL knob to select Set Mode Item 29: PAGER.3. Press the [F/W] key momentarily to enable adjustment of this Set Mode Item.4. Rotate the DIAL knob to select ON.5. Press the PTT switch to save the new setting and activate the Enhanced Paging & CodeSquelch.6. To disable the Enhanced Paging & Code Squelch, just repeat the above procedure,rotating the DIAL knob to select “OFF” in step 4 above.](https://usermanual.wiki/Yaesu-Musen/20175X20.users-manual/User-Guide-424512-Page-24.png)
![FCC ID: K6620175X20IC ID: 511B-20175X20Operating Manual 25/44Vertex Standard Co., Ltd.R.F. Says: 1) In the factory default configuration, you may recall Set Mode Item 29: PAGERby pressing [F/W] Æ [7(P1)].2) During Enhanced Paging & Code Squelch operation, you may set up the FT-60R such thata ringing “bell” sound alerts you to the fact that a call is coming in, as described previously.See page ?? for details.Paging Answer BackWhen you press the PTT switch to respond to a page call, the FT-60R transmits the sameCTCSS tone pair. This tone pair will open the Code Squelch of the calling station. If youprefer, you can have the FT-60R respond to page calls automatically (“transpond”).To enable this feature:1. Press the [F/W] key, then press the [%(0)SET] key to enter the Set mode.2. Rotate the DIAL knob to select Set Mode Item 31: PAG.ABK.3. Press the [F/W] key momentarily to enable adjustment of this Set Mode Item.4. Rotate the DIAL knob to select ABK. ON.5. Press the PTT switch to save the new setting and exit to normal operation.R.F. Says: The Paging Answer Back feature constitutes a form of “remote control” operationthat may be restricted to certain frequencies. U.S. users should confirm the current status of§97.201(b) of the FCC’s rules governing the Amateur service before utilizing this feature onthe 144 MHz band.Emergency FeatureEmergency Channel OperationThe FT-60R includes an “Emergency” feature which may be useful if you have someonemonitoring on the same frequency as your transceiver’s UHF “Home” channel. See page ??for details on setting the Home channel.The “Emergency” feature is activated by pressing and holding in the [4(RPT]] key for onesecond. When this is done, (A) the radio is placed on the UHF amateur band Home channel,(B) it emits a loud “Alarm” sound (the volume is controlled by the VOL knob), (C) it flashes theLCD/keypad lamp, (D) if you press the PTT key, you will disable the Emergency featuretemporarily; you can then transmit on the UHF Home channel, and (E) two seconds after thePTT release, the Emergency feature will resume.To disable the “Emergency” feature, press the [F/W] key momentarily or turn the radio off byrotating the VOL/PWR knob fully counter-clockwise into the click-stop position.Use this feature if you are out for a walk and want a quick way of alerting a family member asto a dangerous situation. The alarm sound may discourage an attacker and allow you toescape.R.F. Says: 1) Be sure to arrange with a friend or family member to be monitoring on the samefrequency, as there will be no identification sent via the Emergency alarm sound. And do nottransmit the alarm tone except in a true emergency!2) The “Emergency” feature may be changed to another function via Set Mode Item 19: EMGS; see page ?? for details.Emergency Automatic ID (EAI) FeatureThe Emergency Automatic ID (EAI) feature can be used for searching for persons who areincapacitated in a disasters like earthquakes, especially search-and-rescue personnel whomay have become injured in a debris field. In such cases, if another searcher sends a uniquecommand (CTCSS tone pair), the radio of the incapacitated party, who may not be able tospeak or even press the PTT, will automatically cause the injured party’s radio to transmit, so](https://usermanual.wiki/Yaesu-Musen/20175X20.users-manual/User-Guide-424512-Page-25.png)
![FCC ID: K6620175X20IC ID: 511B-20175X20Operating Manual 26/44Vertex Standard Co., Ltd.others may perform direction-finding and effect a rescue. The callsign of the incapacitatedperson will also be transmitted, to assist the rescue team.If an emergency group is working in a dangerous area, all members should engage the EAIfeature on their transceiver, so that others can provide assistance to a fallen team member, ifnecessary.The “callsign” ID can be changed to any desired sequence of characters, such as a name.After sending the callsign or name, the radio will repeatedly transmit three tones for a user-defined period of time (between 1 and 30 minutes). The callsign or name will be transmittedevery 10 minutes.When the FT-60R receives the CTCSS tone pair which is stored in the Pager Code Memory(configured via Set Mode Item 30: PAG.COD) on the frequency which is stored in MemoryChannel “000,” the radio will automatically transmit at the power level stored in that memorychannel; it is NOT necessary for the incapacitated person to press the PTT switch. Furthermore, if your call sign is stored in the radio by Set Mode Item 11: CW WRI, transmit yourcallsign on the air at the activating this feature, and after that every two minutes.The Emergency TX Request feature requires that you (1) store the CTCSS Tone Pair into thePager Memory (see page ?? for procedure), and (2) store the desired UHF coordinationfrequency into Memory Channel “000” (see page ?? for procedure).To enable this feature:1. Press the [F/W] key, then press the [%(0)SET] key to enter the Set mode.2. Rotate the DIAL knob to select Set Mode Item 20: EAI.3. Press the [F/W] key momentarily to enable adjustment of this Set Mode Item.4. Rotate the DIAL knob to select desired transmit time (between 1 and 30 minutes) orOFF.5. Press the PTT switch to save the new setting and exit to normal operation.6. To disable the Emergency Automatic ID feature, just repeat the above procedure,rotating the DIAL knob to select “OFF” in step 4 above.When the Emergency Automatic ID feature is activated, the “Telephone” icon will blink in theLCD.Smart Search OperationThe Smart Search feature allows you to load frequencies automatically according to whereactivity is encountered by your radio. When Smart Search is engaged, the transceiver willsearch above and below your current frequency, storing active frequencies as it goes(without stopping on them even momentarily); these frequencies are stored into a specialSmart Search memory bank, consisting of 31 memories (15 above the current frequency, 15below the current frequency, plus the current frequency itself).Two basic operating modes for Smart Search are available:SINGLE: In this mode, the transceiver will sweep the current band once in each directionstarting on the current frequency. All channels where activity is present will be loaded into theSmart Search memories; whether or not all 31 memories are filled, the search will stop afterone sweep in each direction.CONT: In this mode, the transceiver will make one pass in each direction as with One-Shotsearching; if all 31 channels are not filled after the first sweep, however, the radio willcontinue sweeping until they are all filled.Setting the Smart Search Mode1. Press the [F/W] key, then press the [%(0)SET] key to enter the Set mode.](https://usermanual.wiki/Yaesu-Musen/20175X20.users-manual/User-Guide-424512-Page-26.png)
![FCC ID: K6620175X20IC ID: 511B-20175X20Operating Manual 27/44Vertex Standard Co., Ltd.2. Rotate the DIAL knob to select Set Mode Item 41: S SRCH.3. Press the [F/W] key momentarily to enable adjustment of this Set Mode Item.4. Rotate the DIAL knob to select the desired Smart Search mode (see above).5. When you have made your selection, press the PTT switch to save the setting and exit tonormal operation.Storing Smart Search Memories1. Set the radio to the VFO mode. Be sure that you have the Squelch adjusted properly (sothat band noise is quieted).2. Press and hold in the [3(TX PO)] key for one second to begin the Smart Searchscanning.3. As active channels are detected, you will observe the number of “loaded” channelsincreasing in the regular memory channel window.4. Depending on the mode you set for Smart Search operation (“SINGLE” or “CONT”), theSmart Search scan will eventually terminate, and the LCD will revert to Smart SearchMemory Channel “C.”5. To recall the Smart Search memories, rotate the DIAL knob to choose from among thefrequencies stored by Smart Search.6. To return to normal operation, press the [V/M(PRI)] key.R.F. Says: Smart Search is a great tool when visiting a city for the first time. You don’t need tospend hours looking up repeater frequencies from a reference guidebook. . .just ask yourFT-60R where the action is!Internet Connection featureThe FT-60R can be used to access a “node” (repeater or base station) which is tied into theVertex Standard WIRES™ (Wide-Coverage Internet Repeater Enhancement System)network, operating in the “SRG” (Sister Radio Group) mode. Details may be found at theWIRES-II Web site: http://www.vxstd.com/en/wiresinfo-en/. This feature may also be used toaccess other systems, as described below.1. Press and hold in the [%(0)SET] key for one second to activate the Internet Connectionfeature (the “Internet” icon will appear in the upper right corner of the display) and enabletransmission of the access number (single DTMF code) for the local WIRES™ node.2. Rotate the DIAL knob to select the access number corresponding to the WIRES™ nodeto which you wish to establish an Internet link (ask the node or repeater owner/operatorif you don’t know the access number in the network). Now press the PTT switch to exitfrom the selection mode.3. With the Internet Connection feature activated (as in step 1 above), the FT-60R willgenerate a brief (0.1 second) DTMF tone according to your selection in step 2. ThisDTMF tone is sent at the beginning of every transmission to establish or maintain the linkto the local WIRES™ node operating in the SRG mode.4. To disable the Internet Connection feature, press the [%] key momentarily (the “Internet”icon will disappear from the display).R. F. Says: If other users report that you always have a DTMF “beep” at the beginning ofeach transmission, and you are not operating in conjunction with Internet access, disable thisfunction via step (4) above.You may access other Internet Link Systems (including WIRESTM in the “FRG” mode) thatuse a DTMF string for access.1. Load the DTMF tones which you wish to use for Internet-link access into a DTMFAutodial memory register. For purposes of this example, we will use “#123” as theaccess code.](https://usermanual.wiki/Yaesu-Musen/20175X20.users-manual/User-Guide-424512-Page-27.png)
![FCC ID: K6620175X20IC ID: 511B-20175X20Operating Manual 28/44Vertex Standard Co., Ltd.A. Press the [F/W] key, then press the [%(0)SET] key to enter the Set mode.B. Rotate the DIAL knob to select Set Mode Item 17: DT WRT.C. Press the [F/W] key to enable adjustment of this Set Mode Item.D. Rotate the DIAL knob to select the DTMF Memory register into which you wish tostore the access code.E. Press the [F/W] key momentarily. The first digit will blink.F. Rotate the DIAL knob to select “F” (representing DTMF “#”: the first digit of theDTMF string).G. Press the [F/W] key momentarily to accept the first digit and move to the seconddigit of the DTMF string.H. Repeat the previous steps until you have completed the access code (“#123”).I. Press and hold in the [F/W] key for one second to save the setting.2. Press the PTT switch to save the setting and exit to normal operation.3. Press the [F/W] key, then press the [%(0)SET] key to enter the Set mode again.4. Rotate the DIAL knob to select Set Mode Item 21: I NET.5. Press the [F/W] key to enable adjustment of this Set Mode Item.6. Rotate the DIAL knob to set this Set Mode Item to “INT.MEM” (thus activating the “OtherInternet Link System” mode).7. Press the PTT key to save the new settings and activate the Internet Connection feature.The “Internet” icon will appear in the upper right corner of the display.8. If you have stored multiple DTMF strings for access to different link nodes, rotate theDIAL knob, while pressing and holding in the [%] key, to select the DTMF Memoryregister (CH1 - CH9) corresponding to that node’s DTMF access string.9. Whit the Internet Connection feature is activated per step 6 above, you may now pressthe [%] key, while you are transmitting, to send out the selected DTMF string (toestablish the link to the desired Internet-link mode).10. To return to the WIRES™ mode, repeat steps 2 - 5 above.ARTS™ (Automatic Range Transponder System)The ARTS™ feature uses DCS signaling to inform both parties when you and anotherARTS™-equipped station are within communications range. This may be particularly usefulduring Search-and Rescue situations, where is important to stay in contact with othermembers of your group.Both stations must set up their DCS codes to the same code number, then activate theirARTS™ feature using the command appropriate for their radio. Alert ringers may be activated,if desired.Whenever you push the PTT, or every 25 (or 15) seconds after ARTS™ is activated, yourradio will transmit a signal which includes a (subaudible) DCS signal for about 1 second. Ifthe other radio is in range, the beeper will sound (if enabled) and the display will show “INRNG” as opposed to the out of range display “OUT RNG” in which ARTS™ operation begins.Whether you talk or not, the polling every 15 or 25 seconds will continue until you de-activateARTS™. Every 10 minutes, moreover, you can have your radio transmit your callsign via CW,so as to comply with identification requirements. When ARTS™ is de-activated, DCS will alsobe deactivated (if you were not using it previously in non-ARTS™ operation).If you move out of range for more than one minute (four pollings), your radio will sense that nosignal has been received, three beeps will sound, and the display will revert to “OUT RNG.” Ifyou move back into range, your radio will again beep, and the display will change back to the“IN RNG” indication.](https://usermanual.wiki/Yaesu-Musen/20175X20.users-manual/User-Guide-424512-Page-28.png)
![FCC ID: K6620175X20IC ID: 511B-20175X20Operating Manual 29/44Vertex Standard Co., Ltd.During ARTS™ operation, your operating frequency will continue to be displayed, but nochanges may be made to it or other settings; you must terminate ARTS™ in order to resumenormal operation. This is a safety feature designed to prevent accidental loss of contact dueto channel change, etc.Basic ARTS™ Setup and Operation1. Set your radio and the other radio(s) to the same DCS code number, per the discussionon page ??.2. Press and hold in the [2(CODE)] key for one second. You will observe the “OUT RNG”display on the LCD below the operating frequency. ARTS™ operation has nowcommenced.3. Every 25 seconds, your radio will transmit a “polling” call to the other station. When thatstation responds with its own ARTS™ polling signal, the display will change to “IN RNG”to confirm that the other station’s polling code was received in response to yours.4. Press the [F/W] key momentarily to exit ARTS™ operation and resume normalfunctioning of the transceiver.R.F. Says: ARTS™ constitutes a form of “remote control” operation that may be restricted tocertain frequencies. U.S. users should confirm the current status of §97.201(b) of the FCC’srules governing the Amateur service before utilizing this feature on the 144 MHz band.ARTS™ Polling Time OptionsThe ARTS™ feature may be programmed to poll every 25 seconds (default value) or 15seconds. The default value provides maximum battery conservation, because the pollingsignal is sent out less frequently. To change the polling interval:1. Press the [F/W] key, then press the [%(0)SET] key to enter the Set mode.2. Rotate the DIAL knob to select Set Mode Item 3: AR INT.3. Press the [F/W] key momentarily to enable adjustment of this Set Mode Item.4. Rotate the DIAL knob to select the desired polling interval (15 or 25 seconds).5. When you have made your selection, press the PTT switch to save the new setting andexit to normal operation.ARTS™ Alert Beep OptionsThe ARTS™ feature allows two kinds of alert beeps (with the additional option of turning themoff), so as to alert you to the current status of ARTS™ operation. Depending on your locationand the potential annoyance associated with frequent beeps, you may choose the Beepmode which best suits your needs. The choices are:INRANG: The beeps are issued only when the radio first confirms that you are within range,but does not re-confirm with beeps thereafter.ALWAYS: Every time a polling transmission is received from the other station, the alert beepswill be heard.OFF: No alert beeps will be heard; you must look at the display to confirm current ARTS™status.To set the ARTS™ Beep mode, use the following procedure:1. Press the [F/W] key, then press the [%(0)SET] key to enter the Set mode.2. Rotate the DIAL knob to select Set Mode Item 2: AR BEP.3. Press the [F/W] key momentarily to enable adjustment of this Set Mode Item.4. Rotate the DIAL knob to select the desired ARTS™ Beep mode (see above).5. When you have made your selection, press the PTT switch to save the new setting andexit to normal operation.CW Identifier SetupThe ARTS™ feature includes a CW identifier, as discussed previously. Every ten minutesduring ARTS™ operation, the radio can be instructed to send “DE (your callsign) K” if this](https://usermanual.wiki/Yaesu-Musen/20175X20.users-manual/User-Guide-424512-Page-29.png)
![FCC ID: K6620175X20IC ID: 511B-20175X20Operating Manual 30/44Vertex Standard Co., Ltd.feature is enabled. The callsign field may contain up to 6 characters.Here’s how to program the CW Identifier:1. Press the [F/W] key, then press the [%(0)SET] key to enter the Set mode.2. Rotate the DIAL knob to select Set Mode Item 11: CW WRT.3. Press the [F/W] key momentarily to display any previously-stored callsign.4. Press the [F/W] key again to clear any previous callsign.5. Rotate the DIAL knob to select the first letter/number of your callsign, then press the[F/W] key momentarily to save the first letter/number and move on to the next character.6. Repeat the previous step, as many times as necessary, to complete your callsign. If youmake a mistake, press the [DOWN] key to move back to the previous letter/number’sslot, then re-select the correct letter/number.7. When you have finished entering your entire callsign and it contains less than 6characters, press and hold in the [F/W] key for one second to confirm the callsign. (if youcallsign has exactly 6 characters, you do not need to press and hold in [F/W] in thisstep).8. Press the PTT switch to save the settings and exit to normal operation.9. Press the [F/W] key, then press the [%(0)SET] key to enter the Set mode again.10. Rotate the DIAL knob to select Set Mode Item 10: CWID.11. Press the [F/W] key momentarily, then rotate the DIAL knob to set this Item to “TX ON”(to enable the CW ID function).12. Press the PTT switch to save the settings and exit to normal operation.R.F. Says: You may check your work by monitoring the entered callsign. To do this, repeatsteps 1- 7 above, then press the MONI switch.DTMF OperationThe FT-60R’s 16-button keypad allows easy DTMF dialing for Autopatch, repeater control, orInternet-link access purposes. Besides numerical digits [0] through [9], the keypad includesthe [*] and [#] digits, plus the [A], [B], [C], and [D] tones often used for repeater control.Manual DTMF Tone GenerationYou can generate DTMF tones during transmission manually.1. Press the [F/W] key, then press the [9(DTMF)] key to disable the DTMF Autodialer, ifnecessary. The “CODE” indication will appear in the display for a moment.2. Press the PTT switch to begin transmission.3. While transmitting, press the desired numbers on the keypad.4. When you have sent all the digits desired, release the PTT switch.DTMF AutodialerNine DTMF Autodial memories are provided, allowing you to store telephone numbers forautopatch use. You can also store short autopatch or Internet-link access code streams so asto avoid having to send them manually.Here is the DTMF Autodial storage procedure:1. Press the [F/W] key, then press the [%(0)SET] key to enter the Set mode.2. Rotate the DIAL knob to select Set Mode Item 17: DT WRT.3. Press the [F/W] key momentarily to enable adjustment of this Set Mode Item.4. Rotate the DIAL knob to select the DTMF Memory register into which you wish to storethis DTMF string.5. Press the [F/W] key momentarily to begin DTMF Memory entry into the selected register.6. Rotate the DIAL knob to select the first digit of the DTMF string. Selectable entries are 0- 9, and A – F, with E and F representing DTMF “*” and “#” tones respectively.7. Press the [F/W] key to accept the first digit and move to the next digit of the DTMF string.8. Repeat steps 5 and 6 until you have completed the telephone number.](https://usermanual.wiki/Yaesu-Musen/20175X20.users-manual/User-Guide-424512-Page-30.png)
![FCC ID: K6620175X20IC ID: 511B-20175X20Operating Manual 31/44Vertex Standard Co., Ltd.9. If you make a mistake, press the [DOWN] key to move back to the previous digit, thenre-select the correct number.10. If the telephone number made up of numbers only, you may key in the telephone numberdirectly from the keypad.11. Press and hold in the [F/W] key for one second to save the setting.12. If you store other numbers, repeat steps 4- 10 above, using a different DTMF memoryregister.13. When all required DTMF memories are filled to your satisfaction, press the PTT switch tosave the settings and exit to normal operationTo send the telephone number:1. Press the [F/W] key, then press the [9(DTMF)] key to activate the DTMF Autodialer. The“MEM” indication display will appear in the display for a moment.2. While the DTMF Autodialer is activated, first press the PTT switch, then press thenumerical key ([1] through [9]) corresponding to the DTMF memory string you wish tosend. Once the string begins, you may release the PTT switch, as the transmitter will beheld “on the air” until the DTMF string is completed.3. To disable the DTMF Autodialer, press [F/W] Æ [9(DTMF)] again. The “CODE” indicationwill appear in the display for a moment.You can change the DTMF Audodialer sending speed, using Set Mode Item 16: DT SPD.See page ?? for details.You can also set a longer delay between the time you press the numerical key(corresponding to the DTMF memory string; with PTT switch pressed) and the instant whenthe first DTMF digit is sent, using Set Mode Item 15: DT DLY. See page ?? for details.Miscellaneous SettingsPasswordThe FT-60R provides the password feature which can minimize the chance that yourtransceiver could be used by an unauthorized party.When the password feature is activated, the radio will ask for the four digit password to beentered when the radio is first turned on. You must enter the four digit password from thekeypad. If the wrong password is entered, the microprocessor will shut down the radioautomatically.To enter the password , use the following procedure:1. Press the [F/W] key, then press the [%(0)SET] key to enter the Set mode.2. Rotate the DIAL knob to select Set Mode Item 33 PSWD W.3. Press the [F/W] key momentarily to display any previously-stored password.4. Press the [F/W] key again to clear any previous password.5. Rotate the DIAL knob to select the first digit of the desired number/letter (0-9, A, B, C, D,E (substitute for “*”), and F (substitute for “#”).6. Press the [F/W] key to move to the next digit.7. Repeat steps 5 and 6 to program the remaining numbers/letters of the desiredpassword.8. If you make a mistake, press the [DOWN] key to move back to the previous digit, thenre-select the correct number/letter.9. If your password is made up of numbers only, you may enter your password directly fromthe keypad. For example, to enter the “1234” as your password, press [1(SQ TYP)] Æ[2(CODE)] Æ [3(TX PO)] Æ [4(RPT)].10. When you have finished entering the password, press the PTT switch to save the newsetting and exit to normal operation.](https://usermanual.wiki/Yaesu-Musen/20175X20.users-manual/User-Guide-424512-Page-31.png)
![FCC ID: K6620175X20IC ID: 511B-20175X20Operating Manual 32/44Vertex Standard Co., Ltd.R.F. Says: We recommend that you to write down the password number, and keep it in a safeplace you can easily find if you forget your password.To Activate the Password feature:1. Press the [F/W] key, then press the [%(0)SET] key to enter the Set mode.2. Rotate the DIAL knob to select Set Mode Item 32 PSWD.3. Press the [F/W] key momentarily to enable adjustment of this Item.4. Rotate the DIAL knob to set this Set Mode Item to “PWD. ON.”5. When you have made your selection, press the PTT switch to save the new setting andexit to normal operation.6. If you wish to disable the Password feature, just repeat the above procedure, rotating theDIAL knob to select “PWD.OFF” in step 4 above.(!) If you forget the password number, you may turn on the transceiver by performing the “AllReset” procedure (see page ??). However, the FT-60R will clear the password, as well as allmemories, and will restore all other settings to factory defaults.Programming the Key AssignmentsDefault FT-60R Set Mode Items have been assigned (at the factory) to the [7(P1)] and [8(P2)]keys. These may be changed by the user, if you wish to assign another Set Mode Item toeither or both of these keys.To change the assignment of a key’s Set Mode Item:1. Press the [F/W] key, then press the [%(0)SET] key to enter the Set mode.2. Rotate the DIAL knob to select the Set Mode Item which you wish to assign to the key asa Menu short-cut.3. Press and hold in the [7(P1)] or [8(P2)] key for one second to assign the Set Mode Itemto the [7(P1)] or [8(P2)] key.R.F. Says: The following Set Mode Items may not be assigned to the [7(P1)] and [8(P2)]keys.Set Mode Item 11: CW WRTSet Mode Item 17: DT WRTSet Mode Item 33: PSWD WChanging the Channel StepsThe FT-60R’s synthesizer provides the option of utilizing channel steps of5/10/12.5/15/20/25/50/100 kHz per step, as well as an automatic step selection based on thecurrent operating frequency (“AUTO”), any number of which may be important to youroperating requirements. The FT-60R is set up at the factory in the “AUTO” configuration,which probably is satisfactory for most operation. However, if you need to change thechannel step increments, the procedure to do so is very easy.1. Press the [F/W] key, then press the [%(0)SET] key to enter the Set mode.2. Rotate the DIAL knob to select Set Mode Item 48: STEP.3. Press the [F/W] key momentarily to enable adjustment of this Item.4. Rotate the DIAL knob to select the new channel step size.5. When you have made your selection, press the PTT switch to save the new setting andreturn to normal operation.Changing the Receiving ModeThe FT-60R provides for automatic mode changing when the radio is tuned to differentoperating frequencies. However, should an unusual operating situation arise in which youneed to change between the available operating modes (FM and AM), here is the procedurefor doing so:1. Press the [F/W] key, then press the [%(0)SET] key to enter the Set mode.2. Rotate the DIAL knob to select Set Mode Item 39: RX MODE.](https://usermanual.wiki/Yaesu-Musen/20175X20.users-manual/User-Guide-424512-Page-32.png)
![FCC ID: K6620175X20IC ID: 511B-20175X20Operating Manual 33/44Vertex Standard Co., Ltd.3. Press the [F/W] key momentarily to enable adjustment of this Item.Rotate the DIAL knob to select the new operating mode. The available selections are:AUTO: Automatic mode setting per default values for the selected frequency range.FM: Frequency ModulationAM: Amplitude Modulation4. When you have made your selection, press the PTT switch to save the new setting andreturn to normal operation.R.F. Says: Unless you have a compelling reason to do so, leave the Automatic ModeSelection feature on so as to save time and trouble when changing bands. If you make amode change for a particular channel or station, you can always store that one channel intomemory, as the mode setting will be memorized along with the frequency information.Receive Battery Saver SetupAn important feature of the FT-60R is its Receive Battery Saver, which “puts the radio tosleep” for a time interval, periodically “waking it up” to check for activity. If somebody is talkingon the channel, the FT-60R will remain in the “active” mode, then resume its “sleep” cycles.This feature significantly reduces quiescent battery drain, and you may change the amount of“sleep” time between activity checks using the Set Mode:1. Press the [F/W] key, then press the [%(0)SET] key to enter the Set mode.2. Rotate the DIAL knob to select Set Mode Item 40: RXSAVE.3. Press the [F/W] key momentarily to enable adjustment of this Set Mode Item.4. Rotate the DIAL knob to select the desired “sleep” duration. The selections available are200 ms, 300 ms, 500 ms, 1 second, 2 seconds, or OFF. The default value is 200 ms.5. When you have made your selection, press the PTT switch to save the new setting andexit to normal operation.R.F. Says: When you are operating on Packet, switch the Receive Battery Saver OFF, as thesleep cycle may “collide” with the beginning of an incoming Packet transmission, causingyour TNC not to receive the full data burst.TX Battery SaverThe FT-60R also includes a useful Transmit Battery Saver, which will automatically lower thepower output level when the last signal received was very strong. For example, when you arein the immediate vicinity of a repeater station, there generally is no reason to use the HighPower output in order to achieve full-quieting access to the repeater. With the TransmitBattery Saver, the automatic selection of Low Power operation conserves battery drainsignificantly.To activate the Transmit Battery Saver:1. Press the [F/W] key, then press the [%(0)SET] key to enter the Set mode.2. Rotate the DIAL knob to select Set Mode Item 52: TXSAVE.3. Press the [F/W] key momentarily to enable adjustment of this Set Mode Item.4. Rotate the DIAL knob to set this Set Mode Item to “SAV. ON” (thus activating theTransmit Battery Saver).5. When you have made your selection, press the PTT switch to save the new setting andexit to normal operation.Disabling the TX/BUSY IndicatorFurther battery conservation may be accomplished by disabling the TX indicator whiletransmitting and disabling the BUSY indicator while receiving a signal. Use the followingprocedure:1. Press the [F/W] key, then press the [%(0)SET] key to enter the Set mode.2. Rotate the DIAL knob to select Set Mode Item 8: BSY.LED if you wish to disable theBUSY indicator or Set Mode Item 51: TX.LED if you wish to disable the TX indicator.](https://usermanual.wiki/Yaesu-Musen/20175X20.users-manual/User-Guide-424512-Page-33.png)
![FCC ID: K6620175X20IC ID: 511B-20175X20Operating Manual 34/44Vertex Standard Co., Ltd.3. Press the [F/W] key momentarily to enable adjustment of this Set Mode Item.4. Rotate the DIAL knob to set this Set Mode Item to “LED.OFF” (thus disabling the BUSYor TX lamp).5. When you have made your selection, press the PTT switch to save the new setting andexit to normal operation.6. If you wish to re-enable the TX/BUSY Indicator, just repeat the above procedure, rotatingthe DIAL knob to select “LED. ON” in step 4 above.Automatic Power-Off (APO) FeatureThe APO feature helps conserve battery life by automatically turning the radio off after auser-defined period of time within which there has been no dial or key activity. The availableselections for the time before power-off are 0.5 to 12.0 hours in 0.5 hour multiple, as well asAPO Off. The default condition for the APO is OFF, and here is the procedure for activating it:1. Press the [F/W] key, then press the [%(0)SET] key to enter the Set mode.2. Rotate the DIAL knob to select Set Mode Item 1: APO.3. Press the [F/W] key momentarily to enable adjustment of this Set Mode Item.4. Rotate the DIAL knob to select the desired time period after which the radio willautomatically shut down.5. When you have made your selection, press the PTT switch to save the new setting andexit to normal operation.When the APO is activated, the “TIMER” icon will appear at the upper right corner on the LCD.If there is no action by you within the time interval programmed, the microprocessor will shutdown the radio automatically.Rotate the VOL/PWR knob to “off” and “on” to turn the transceiver back on after an APOshutdown, as usual.Transmitter Time-Out Timer (TOT)The TOT feature provides a safety switch which limits transmission time to a pre-programmed value. This will promote battery conservation by not allowing you to makeexcessively-long transmissions, and in the event of a stuck PTT switch (perhaps if the radioor a Speaker/Mic is wedged between car seats) it can prevent interference to other users aswell as battery depletion. As configured at the factory the TOT feature is set to OFF, and hereis the procedure for activating it:1. Press the [F/W] key, then press the [%(0)SET] key to enter the Set mode.2. Rotate the DIAL knob to select Set Mode Item 50: TOT.3. Press the [F/W] key momentarily to enable adjustment of this Set Mode Item.4. Rotate the DIAL knob to set the Time-Out Timer to the desired “Maximum TX” time(between 1 and 30 minutes), or OFF.5. When you have made your selection, press the PTT switch to save the new setting andexit to normal operation.R.F. Says: 1) When your transmission time is within 10 seconds of the Time-Out Timerexpiration, an Alert bell will provide an audible warning from the speaker.2) Since brief transmissions are the mark of a good operator, try setting up your radio’s TOTfeature for a maximum transmission time of one minute. This will significantly improve batterylife, too!Busy Channel Lock-Out (BCLO)The BCLO feature prevents the radio’s transmitter from being activated if a signal strongenough to break through the “noise” squelch is present. On a frequency where stations usingdifferent CTCSS or DCS codes may be active, BCLO prevents you from disrupting theircommunications accidentally (because your radio may be muted by its own Tone Decoder).The default setting for the BCLO is OFF, and here is how to change that setting:1. Press the [F/W] key, then press the [%(0)SET] key to enter the Set mode.2. Rotate the DIAL knob to select Set Mode Item 5: BCLO.](https://usermanual.wiki/Yaesu-Musen/20175X20.users-manual/User-Guide-424512-Page-34.png)
![FCC ID: K6620175X20IC ID: 511B-20175X20Operating Manual 35/44Vertex Standard Co., Ltd.3. Press the [F/W] key momentarily to enable adjustment of this Set Mode Item.4. Rotate the DIAL knob to set this Set Mode Item to “BCL. ON” (thus activating the BCLOfeature).5. When you have made your selection, press the PTT switch to save the new setting andexit to normal operation.Mono Band OperationYou may place the radio in a “VHF Only” or “UHF Only” mode which will cause it to function asa 144 MHz or 430 MHz Mono band transceiver.To place the radio into the Mono band operation configuration:1. Turn the radio off.2. Press and hold in the MONI switch (just below the PTT switch) while turning the radio on.3. Rotate the DIAL knob to select the configuration mode menu:F6 V-ONLY: The FT-60R will operate on the 144 MHz band only.F7 U-ONLY: The FT-60R will operate on the 430 MHz band only.4. Press the [F/W] key momentarily.To return to normal operation, press and hold in the MONI switch while turning the radio on,and then press the [F/W] key momentarily.DCS Code InversionThe DCS system was first introduced in the commercial LMR (Land Mobile Radio) service,where it is now in widespread use. DCS is sometime referred to by its different proprietarynames, such as DPL® (Digital Private Line®, a registered trademark of Motorola, Inc.).DCS uses a codeword consisting of a 23-bit frame, transmitted (subaudible) at a data rate of134.4 bps (bit/sec). Occasionally, signal inversion can result in the complement of a code tobe sent or received. This prevents the receiver’s squelch from opening with DCS enabled, asthe decoded bit sequence would not match that selected for operation.Typical situations that might cause inversion to occur are: Connection of an external receiver preamplifier. Operating through a repeater. Connection of an external linear amplifier.Note that code inversion does not mean that any of the above listed equipment is defective!In certain amplifier configurations, the output signal (phase) is inverted from the input. Smallsignal or power amplifiers having an odd number (1, 3, 5, etc.) of amplification stages mayresult in inversion of a transmitted or received DCS code.While under most circumstances this should not occur (amplifier designs and industrystandards take this into account), if you find that your receiver squelch does not open whenboth you and the other station are using a common DCS code, you or the other station (butnot both) can try the following:1. Press the [F/W] key, then press the [%(0)SET] key to enter the Set mode.2. Rotate the DIAL knob to select Set Mode Item 14: DCS.N/R.3. Press the [F/W] key momentarily, then rotate the DIAL knob to select one of the followingmodes:T/RX N: Encoder, Normal; Decoder, NormalRX R: Encoder, Normal; Decoder, Reverse (Inverted)TX R: Encoder, Reverse (Inverted); Decoder, NormalT/RX R: Encoder, Reverse (Inverted); Decoder, Reverse (Inverted)4. When you have made your selection, press the PTT switch to save the new setting andexit to normal operation.](https://usermanual.wiki/Yaesu-Musen/20175X20.users-manual/User-Guide-424512-Page-35.png)
![FCC ID: K6620175X20IC ID: 511B-20175X20Operating Manual 36/44Vertex Standard Co., Ltd.5. Remember to restore the default setting to “T/RX N” (Encoder; Normal, Decoder;Normal) when done.Changing the TX Deviation LevelIn many areas of the world, channel congestion has required that operating channels beclosely spaced. In such operating environments, it often is required that operators usereduced deviation levels, so as to reduce the potential for interference to users on adjacentchannels. The FT-60R includes a simple method of accomplishing this:1. Press the [F/W] key, then press the [%(0)SET] key to enter the Set mode.2. Rotate the DIAL knob to select Set Mode Item 54: WID.NAR.3. Press the [F/W] key momentarily to enable adjustment of this Set Mode Item.4. Rotate the DIAL knob to set this Set Mode Item to “NARROW.” In this configuration(HALF DEVIATION active), the transmitter’s deviation will be approximately ±2.5 kHz,and the received audio output level will be increased, for easier listening on the narrowsignal.5. When you have made your selection, press the PTT switch to save the new setting andexit to normal operation.R.F. Says: The “normal” setting for the deviation (when this Menu Item is set to WIDE) is ±5kHz.Reset ProceduresIn the event of erratic operation of the transceiver, it is possible that data on themicroprocessor may have become corrupted. While this is a highly unusual situation, the onlypath to recovery may involve resetting of the microprocessor. Here’s how to do this:1. Turn the radio off.2. Press and hold in the MONI switch (just below the PTT switch) while turning the radio on.3. Rotate the DIAL knob to select one choice from the reset menu:F1 SETRST: Resets the Set (Menu) mode settings to their factory defaults.F2 MEMRST: Clears the Memory settings to factory defaults.F3 MB RST: Clears the Memory Bank Assignments.F4 ALLRST: Clears all memories and other settings to factory defaults.4. Press the [F/W] key momentarily to complete the reset procedure.CloningThe FT-60R includes a convenient “Clone” feature, which allows the memory andconfiguration data from one transceiver to be transferred to another FT-60R. This can beparticularly useful when configuring a number of transceivers for a public service operation.Here is the procedure for Cloning one radio’s data to another:1. Turn both radios off.2. Connect the optional CT-27 Clone Cable between the MIC/SP jacks of the two radios.3. Press and hold in the MONI switch (just below the PTT switch) while turning the radioson. Do this for both radios (the order of switch-on does not matter).4. Rotate the DIAL job on each radio to select to “F8 CLONE,” then press the [F/W] keymomentarily.5. The display will disappear for a moment, then the “CLONE” notation will appear on thedisplays of both radios when the Clone mode is successfully activated in this step.6. On the Destination radio, press the [V/M(PRI)] key (“WAIT” will appear on the LCD).7. Press the [BAND] key on the Source radio; “TX” will appear on the Source radio, and thedata from this radio will be transferred to the other radio.8. If there is a problem during the cloning process, “ERROR” will be displayed. Check yourcable connections and battery voltage, and try again.9. If the data transfer is successful, “CLONE” will reappear on both displays. Turn both](https://usermanual.wiki/Yaesu-Musen/20175X20.users-manual/User-Guide-424512-Page-36.png)
![FCC ID: K6620175X20IC ID: 511B-20175X20Operating Manual 37/44Vertex Standard Co., Ltd.radios off and disconnect the cloning cable. You can then turn the radios back on, andbegin normal operation.Set (Menu) ModeThe FT-60R Set Mode, already described in parts of many previous chapters, is easy toactivate and set. It may be used for configuration of a wide variety of transceiver parameters,some of which have not been detailed previously. Use the following procedure to activate theSet Mode:1. Press the [F/W] key, then press the [%(0)SET]] key to enter the Set mode.2. Rotate the DIAL knob to select the Set Mode Item to be adjusted.3. Press the [F/W] key momentarily to enable adjustment of the Set Mode Item.4. Rotate the DIAL knob to adjust or select the parameter to be changed on the Set ModeItem selected in above step.5. After completing your selection and adjustment, press the PTT switch momentarily tosave the new setting and exit to normal operation.R.F. Says: 1) Some Set Mode Items (like Set Mode Item 49: TN FRQ) require that the [F/W]key be pressed after setting of the parameter, and before exiting to normal operation.2) Two Set Mode Item numbers (In the factory default, Set Mode Item 29: PAGER, and 45:SKIP) will blink while selecting the Set Mode Item; this indicates that this Set Mode Item hasbeen assigned to the [7(P1)] or [8(P2)] key of the keypad.Set Mode SummarySet Mode Item 1 [APO]Function: Setting of the Automatic Power-Off feature.Available Values: OFF/0.5H - 12.0 H in 0.5 hour multiplesDefault: OFFSet Mode Item 2 [AR BEP]Function: Selects the Beep option during ARTS operation.Available Values: INRANG/ALWAYS/OFFDefault: INRANGINRANG: Beeps sound only when the radio first detects that you are within range.ALWAYS: Beeps sound every time a polling transmission is received from the other station(every 15 or 25 seconds when in range).OFF: No alert beeps sound.Set Mode Item 3 [AR INT]Function: Selects the Polling Interval during ARTS operation.Available Values: 25 SEC/15 SECDefault: 25SECSet Mode Item 4 [ARS]Function: Enables/Disables the Automatic Repeater Shift function.Available Values: ARS. ON/ARS.OFFDefault: ARS. ONSet Mode Item 5 [BCLO]Function: Enables/Disables the Busy Channel Lock-Out feature.Available Values: BCL. ON/BCL.OFFDefault: BCL.OFFSet Mode Item 6 [BEEP]](https://usermanual.wiki/Yaesu-Musen/20175X20.users-manual/User-Guide-424512-Page-37.png)
![FCC ID: K6620175X20IC ID: 511B-20175X20Operating Manual 38/44Vertex Standard Co., Ltd.Function: Enables/Disables the beeper.Available Values: KEY+SC/KEY/OFFDefault: KEY+SCKEY+SC: The beeper sounds when you press any key, or when the scanner stops.KEY: The beeper sounds when you press any key.OFF: Beeper is disabled.Set Mode Item 7 [BELL]Function: Selects the number of CTCSS/DCS Bell ringer repetitions.Available Values: OFF/1T/3T/5T/8T/CONT (Continuous ringing)Default: OFFSet Mode Item 8 [BSY.LED]Function: Enables/Disables the BUSY LED while the Squelch is open.Available Values: LED. ON/LED.OFFDefault: LED. ONSet Mode Item 9 [CLK.SFT]Function: Shifting of the CPU clock frequency.Available Values: SFT.OFF/SFT. ONDefault: SFT.OFFThis function is only used to move a spurious response “birdie,” should it fall on a desiredfrequency.Set Mode Item 10 [CWID]Function: Enables/disables the CW identifier during ARTS operation.Available Values: TX OFF/TX ONDefault: TX OFFSet Mode Item 11 [CW WRT]Function: Programs and activates the CW Identifier (used during ARTS operation).See page ?? for details.Set Mode Item 12 [DC VLT]Function: Indicates the DC Supply Voltage.Set Mode Item 13 [DCS.COD]Function: Setting of the DCS code.Available Values: 104 standard DCS codesDefault: DCS.023Set Mode Item 14 [DCS.N/R]Function: Enables/Disables “Inverted” DCS code decoding.Available Values: T/RX N, RX R, TX R, T/RX RDefault: T/RX NSet Mode Item 15 [DT DLY]Function: Setting of the DTMF Autodialer Delay Time.Available Values: 50MS/100MS/250MS/450MS750MS/1000MSDefault: 450MSSet Mode Item 16 [DT SPD]Function: Setting of the DTMF Autodialer Sending Speed.Available Values: 50MS (high speed)/100MS (low speed)](https://usermanual.wiki/Yaesu-Musen/20175X20.users-manual/User-Guide-424512-Page-38.png)
![FCC ID: K6620175X20IC ID: 511B-20175X20Operating Manual 39/44Vertex Standard Co., Ltd.Default: 50MSSet Mode Item 17 [DT WRT]Function: Programming of the DTMF Autodialer.See page ?? for details.Set Mode Item 18 [EDG.BEP]Function: Enables/Disables the Band-edge beeper while selecting the frequency via theDIAL knob.Available Values: BEP.OFF/ BEP. ONDefault: BEP.OFFSet Mode Item 19 [EMG S]Function: Selects the alarm(s) utilized when the Emergency function is engaged.Available Values:EMG.BEP/EMG.LMP/EMG.B+L/EMG.CWT/EMG.C+B/EMG.C+L/EMG.ALL/OFFDefault: EMG.B+LEMG.BEP: Loud “Alarm” sounds.EMG.LMP: The LCD/Keypad lamp flashes.EMG.B+L: Loud “Alarm” sounds and the LCD/Keypad lamp flashes.EMG.CWT: Transmits the Morse Code “SOS” (••• – – –•••) message on the air beginning oneminute after activation of the Emergency function.EMG.C+B: Loud “Alarm” sounds and the Morse Code “SOS” (••• – – –•••) message istransmitted on the air beginning one minute after activation of the Emergency function.EMG.C+L: The LCD/Keypad lamp flashes, and the Morse Code “SOS” (••• – – –•••) messageis transmitted on the air beginning one minute after activation of the Emergency function.EMG.ALL: All of the above are activated.OFF: Disables the Emergency function. The Emergency function also cannot be engaged, bypressing and holding in the [4(RPT)] key, if this Menu is set to “OFF.”When the radio is set to the EMG.CWT, EMG.C+B, EMG.C+L, or EMG.ALL mode, the radiowill be instructed to send “DE (your callsign)” after the sending of the SOS message, if yourcallsign is entered via Set Mode Item 10 [CWID].Set Mode Item 20 [ETR]Function: Enables/Disables the Emergency TX Request function.Available Values: OFF/ONDefault: OFFSet Mode Item 21 [I NET]Function: Selects the Internet Link Connection mode.Available Values: INT.OFF/INT.COD/INT.MEMDefault: INT.OFFINT.OFF: Disables the Internet Link Connection mode.INT.COD: Sets up the Internet Link Connection mode for WIRESTM access.INT.MEM: Sets up the Internet Link Connection mode for other (DTMF string) Internet LinkSystem access.Set Mode Item 22 [INT CD]Function: Selects the Access Number (DTMF digit) for WIRESTM operation.Available Values: CODE 0 - CODE 9Default: CODE 1Set Mode Item 23 [INT MR]](https://usermanual.wiki/Yaesu-Musen/20175X20.users-manual/User-Guide-424512-Page-39.png)
![FCC ID: K6620175X20IC ID: 511B-20175X20Operating Manual 40/44Vertex Standard Co., Ltd.Function: Selects the memory register for an Access Number (DTMF code) for non-WIRESTMInternet Link System access.Available Values: d1 - d9Default: d1Set Mode Item 24 [LAMP]Function: Selects the LCD/Keypad Lamp mode.Available Values: KEY/5SEC/TOGGLEDefault: KEYKEY: Illuminates the Keypad/LCD for five seconds when you rotate the DIAL knob or pressany key or switch (except the PTT switch).5SEC: Illuminates the Keypad/LCD for five seconds when you press the LAMP switchmomentarily.TOGGLE: Toggles the Keypad/LCD lamp on and off when you press the LAMP switchrepeatedly.Set Mode Item 25 [LOCK]Function: Selects the Control Locking lockout combination.Available Values: LK KEY/LKDIAL/LK K+D/LK PTT/LK P+K/LK P+D/LK ALLDefault: LK KEYNote: “K” = “Key;” “D” = “Dial;” and “P” = “PTT.”Set Mode Item 26 [M/T-CL]Function: Selects the MONI key (just below the PTT switch) function.Available Values: MONI/T-CALLDefault: Depends on the transceiver version.MONI: Pressing the MONI key causes the Noise/Tone Squelch to be over-ridden, allowingyou to listen for weak (or non-encoded) signals.T-CALL: Pressing the MONI key activates a 1750-Hz burst tone, used for repeater access inmany countries (especially in Europe).Set Mode Item 27 [NAME]Function: Toggles the display indication between “frequency” and the channel’s“Alpha/Numeric Tag.”Available Values: FREQ/ALPHADefault: FREQSet Mode Item 28 [NM WRT]Function: Stores Alpha-Numeric “Tags” for the Memory channels.See page ?? for details.Set Mode Item 29 [PAGER]Function: Enables/disables the Enhanced CTCSS Paging & Code Squelch function.Available Values: OFF/ONDefault: OFFSet Mode Item 30 [PAG.COD]Function: Setting the Pager Code for the Enhanced CTCSS Paging & Code Squelch.See page ?? for details.Set Mode Item 31 [PAG.ABK]Function: Enables/disables the Answer Back function of the Enhanced CTCSS Paging &Code Squelch.Available Values: ABK.OFF/ABK. ON](https://usermanual.wiki/Yaesu-Musen/20175X20.users-manual/User-Guide-424512-Page-40.png)
![FCC ID: K6620175X20IC ID: 511B-20175X20Operating Manual 41/44Vertex Standard Co., Ltd.Default: ABK.OFFSet Mode Item 32 [PSWD]Function: Enables/disables the Password feature.Available Values: PWD.OFF/PWD. ONDefault: PWD.OFFSet Mode Item 33 [PSWD W]Function: Stores the password.Available entries are 0-9, A, B, C, D, E (substitute for “*”), and F (substitute for “#”)Set Mode Item 34 [RESUME]Function: Selects the Scan Resume mode.Available Values: BUSY/HOLD/TIMEDefault: BUSYBUSY: The scanner will hold until the signal disappears, then will resume when the carrierdrops.HOLD: The scanner will stop when a signal is received, and will not restart.TIME: The scanner will hold for the five seconds, then resume whether or not the otherstation is still transmitting.Set Mode Item 35 [REV/HM]Function: Selects the function of the [HM/RV] key.Available Values: <REV>/<HOME>Default: <REV><REV>: Pressing the [HM/RV] key reverses the transmit and receive frequencies duringrepeater operation.<HOME>: Pressing the [HM/RV] key instantly recalls a favorite “Home” channel.Set Mode Item 36 [RF SQL]Function: Adjusts the RF Squelch threshold level.Available Values: S-1/S-2/S-3/S-4/S-5/S-6/S-8/S-FULL/OFFDefault: OFFSet Mode Item 37 [RPT.MOD]Function: Sets the Repeater Shift Direction.Available Values: RPT.OFF/RPT. -/RPT. +Default: Depends on the transceiver version, as well as the setting of Set Mode Item 4 [ARS].Set Mode Item 38 [PRI.RVT]Function: Enables/disables the Priority Revert feature.Available Values: RVT.OFF/RVT. ONDefault: RVT.OFFSee page ?? for details.Set Mode Item 39 [RX MOD]Function: Selects the receiving mode.Available Values: AUTO/FM/AMDefault: AUTO (Mode automatically changes according to operating frequency)Set Mode Item 40 [RXSAVE]Function: Selects the Receive-mode Battery Saver interval (“sleep” ratio)Available Values: 200 MS(1:1)/300 MS(1:1.5)/500 MS(1:2.5)/1 S(1:5)/2 S(1:10)/OFFDefault: 200 MS](https://usermanual.wiki/Yaesu-Musen/20175X20.users-manual/User-Guide-424512-Page-41.png)
![FCC ID: K6620175X20IC ID: 511B-20175X20Operating Manual 42/44Vertex Standard Co., Ltd.Set Mode Item 41 [S SRCH]Function: Selects the Smart Search Sweep mode.Available Values: SINGLE/CONTDefault: SINGLESINGLE: The transceiver sweeps the current band once in each direction, starting on thecurrent frequency. All channels where activity is present (up to 15 in each direction) areloaded into the Smart Search memories. Whether or not all 31 memories are filled, thesearch stops after one sweep in each direction.CONT: The transceiver makes a sweep in each direction as with the “SINGLE” mode, but ifall 31 channels are not filled after the first sweep, the radio continues sweeping until they areall filled.Set Mode Item 42 [SCN MD]Function: Selects the Memory Scan channel-selection mode.Available Values: ONLY/MEMDefault: MEMONLY: The scanner will only scan channels that are flagged (Preferential Scan List).MEM: The scanner will “skip” the flagged channels during scanning.Set Mode Item 43 [SCN.LMP]Function: Enables/Disables the Scan lamp while paused.Available Values: ON/OFFDefault: ONSet Mode Item 44 [SHIFT]Function: Sets the magnitude of the repeater Shift.Available Values: 0.00 - 99.95 MHz (50 kHz increments)Default: Depends on the operating band and transceiver version.Set Mode Item 45 [SKIP]Function: Selects the Memory Scan “Skip” channel-selection mode.Available Values: OFF/SKIP/ONLYDefault: OFFSKIP: The scanner will “skip” the flagged channels during scanning.ONLY: The scanner will only scan channels that are flagged (Preferential Scan List).OFF: All memory channels will be scanned (the “flag” will be ignored).Set Mode Item 46 [SPLIT]Function: Enables/Disables split CTCSS/DCS coding.Available Values: SPL.OFF/SPL. ONDefault: SPL.OFFWhen this Set Mode Item is set to “SPL. ON,” you will see the following additional parametersafter the “DCS” parameter while configuring Set Mode Item 47: SQL.TYP.D: DCS Encode only.T DCS: Encodes a CTCSS tone and Decodes a DCS code.D TSQL: Encodes a DCS code and Decodes a CTCSS tone.Select the desired operating mode from the selections shown above.Set Mode Item 47 [SQL.TYP]Function: Selects the Tone Encoder and/or Decoder mode.Available Values: OFF/TONE/TSQL/REV TN/DCSDefault: OFFTONE: CTCSS Encoder](https://usermanual.wiki/Yaesu-Musen/20175X20.users-manual/User-Guide-424512-Page-42.png)
![FCC ID: K6620175X20IC ID: 511B-20175X20Operating Manual 43/44Vertex Standard Co., Ltd.TSQL: CTCSS Encoder/DecoderREV TN: Reverse CTCSS Decoder (Mutes receiver when matching tone is received)DCS: Digital Coded Encoder/DecoderNote: See also Set Mode Item 46: SPLIT regarding additional selections available during“Split Tone” operation.Set Mode Item 48 [STEP]Function: Setting of the synthesizer steps.Available Values: 5/10/12.5/15/20/25/50/100 kHz, or AUTODefault: AUTO (Step automatically changes according to operating frequency.)Set Mode Item 49 [TN FRQ]Function: Setting of the CTCSS Tone Frequency.Available Values: 50 standard CTCSS tonesDefault: 100.0 HzSet Mode Item 50 [TOT]Function: Setting of the TOT timeAvailable Values: 1MIN - 30MIN or OFFDefault: 6MIN (minutes)The time-out timer shuts off the transmitter after continuous transmission of the programmedtime.Set Mode Item 51 [TX.LED]Function: Enables/Disables the TX LED while the radio is transmitting.Available Values: LED. ON/LED.OFFDefault: LED. ONSet Mode Item 52 [TXSAVE]Function: Enables/Disables the Transmitter Battery Saver.Available Values: SAV.OFF/ SAV. ONDefault: SAV.OFFSet Mode Item 53 [VFO.BND]Function: Enables or disables the VFO band edge limiting for the current band.Available Values: BAND/ALLDefault: BANDBAND: When the VFO frequency reaches the high band edge of the current band, the VFOfrequency will jump to the low band edge of the current band (or vice versa).ALL: When the VFO frequency reaches the high edge of the current band, the VFOfrequency will jump to the low band edge of the next band (or vice versa).Set Mode Item 54 [WID.NAR]Function: Select Wide (±5 kHz) or Narrow (±2.5 kHz) TX Deviation.Available Values: WIDE/NARROWDefault: WIDENote: If “Narrow” is selected, the receiver audio level is increased slightly to compensate forthe reduced deviation. The receiver IF filter bandwidth is not changed via this setting.Set Mode Item 55 [WX ALT]Function: Enables/Disables the Weather Alert Scan feature.Available Values: ALT.OFF/ALT. ONDefault: ALT. OFF](https://usermanual.wiki/Yaesu-Musen/20175X20.users-manual/User-Guide-424512-Page-43.png)
