Yaesu Musen VX-7R Amateur Scanning Transceiver User Manual Manual

Yaesu Musen Co., Ltd. Amateur Scanning Transceiver Manual

UserManual.wiki >

Yaesu Musen >

VX-7R User Manual >

Manual HTML Version

1. Manual
2. Manual insert

Manual

FCC ID: K66VX-7R

Operating Manual

Vertex Standard Co., Ltd.

50/144/430 MHz Triple-Band Heavy Duty FM Transceiver

50/144/430 MHz Triple-Band Heavy Duty FM Transceiver50/144/430 MHz Triple-Band Heavy Duty FM Transceiver

50/144/430 MHz Triple-Band Heavy Duty FM Transceiver

VX-

VX-VX-

VX-7R

7R7R

Operating Manual

Operating ManualOperating Manual

Operating Manual

Introduction

IntroductionIntroduction

Introduction

The VX-

VX-VX-

VX-7R

7R7R

7R is a miniature triband FM transceiver with extensive receive frequency

coverage, providing leading-edge features for VHF and UHF two-way amateur

communications along with unmatched monitoring capability.

The VX-

VX-VX-

VX-7R

7R7R

7R’s small size allows you to take it anywhere - hiking, skiing, or while

walking around town, and its operating flexibility brings the user many avenues of

operating enjoyment. Besides 50, 144, and 430 MHz transceive operation, the VX-

VX-VX-

VX-7R

7R7R

provides receive coverage of the AM (MF) and FM broadcast bands, HF Shortwave

Bands up to 16 MHz, VHF and UHF TV bands, the VHF AM aircraft band, and a wide

range of commercial and public safety frequencies! And the optional Barometer

pressure Sensor Unit provides readout of barometric pressure and altitude while

mountain climbing or hiking.

The transmitter section provides 5 Watts of clean power output on the FM operation

on the 50 MHz, 144 MHz, and 430 MHz bands with the supplied FNB-80LI Battery

Pack, and 0.2 Watts output on 430 MHz, and also 1.0 Watts output on AM operation on

50 MHz. A wide variety of tone signaling formats are built into the VX-

VX-VX-

VX-7R

7R7R

7R, in addition to

Yaesu’s exclusive ARTSTM-(Auto-Range Transponder System), which “beeps” the user

when you move out of communications range with another ARTSTM-equipped station.

We appreciate your purchase of the VX-

VX-VX-

VX-7R

7R7R

7R, and encourage you to read this manual

thoroughly, so as to learn about the many exciting features of your exciting new Yaesu

hand-held transceiver!

Controls & Connections

Controls & ConnectionsControls & Connections

Controls & Connections

ANTENNA

ANTENNAANTENNA

ANTENNA

Connect the supplied rubber flex antenna (or another antenna presenting a 50-ohm

impedance) here.

VOLUME

VOLUMEVOLUME

VOLUME

This control adjusts the audio volume level. Clockwise rotation increases the volume

FCC ID: K66VX-7R

Operating Manual

Vertex Standard Co., Ltd.

level.

DIAL

DIALDIAL

DIAL

The main tuning Dial is used for setting the operating frequency, and also is used for

Menu selections and other adjustments.

Intelligent-Beam (I-Beam)

Intelligent-Beam (I-Beam)Intelligent-Beam (I-Beam)

Intelligent-Beam (I-Beam)

The Intelligent-Beam (I-Beam) is the unique indicator which indicate the transceiver’s

status. The I-Beam glows Red during transmission, glows Green when a Main band

signal is being received (of sufficient strength to open the noise squelch), glows Blue

when a Sub band signal is being received (of sufficient strength to open the noise

squelch), and glows Orange when a both (Main & Sub) bands signal are being received

(of sufficient strength to open the noise squelch). Also, the I-Beam flash by various color

while emergency operation.

You may customize the I-Beam color by the menu mode.

MIC

MICMIC

MIC

The internal microphone is located at the bottom right-hand corner of the display.

SPEAKER

SPEAKERSPEAKER

SPEAKER

The internal speaker is located directly below the display.

MONI

MONIMONI

MONI

Pressing this key disables the noise squelching action, allowing you to hear very weak

signals near the background noise level.

PTT

PTTPTT

PTT

Press this key to transmit, and release it to receive after your transmission is

completed.

MIC/SP

MIC/SPMIC/SP

MIC/SP

This four-conductor miniature jack provides connection points for microphone audio,

earphone audio, PTT, and ground.

FCC ID: K66VX-7R

Operating Manual

Vertex Standard Co., Ltd.

EXT DC

EXT DCEXT DC

EXT DC

This coaxial DC jack allows connection to an external DC power source (10-16V DC).

The center pin of this jack is the Positive (+) line.

Display Icons AND Indicators

Display Icons AND IndicatorsDisplay Icons AND Indicators

Display Icons AND Indicators

Double size display (default)

Press and hold the [4(MG) DSP] key for one second

Small character display

Frequency/Data Field

S- and TX Power Meter

Operating Mode

Low Battery!

Battery Saver Active (page ??)

DTMFG Autodialer Active (page ??)

Bell Alarm Active (page ??)

Low TX Power Selected (page ??)

Automatic Power-Off Active (page ??)

Digital Coded Squelch Active (page ??)

CTCSS Decoder Active (page ??)

CTCSS Encoder Active (page ??)

Repeater Shift Direction (page ??)

Dual Watch Active (page ??)

Keypad Function

Keypad FunctionKeypad Function

Keypad Function

[1(SCAN)] key

Press key: Frequency entry digit “1.”

Press [MON/F] +: Activate the Scanner.

Press and hold key: Store the current setting into the Hyper Memory “1.”

[2(DW)] key

Press key: Frequency entry digit “2.”

Press [MON/F] +: Activate the Dual Watch Feature.

FCC ID: K66VX-7R

Operating Manual

Vertex Standard Co., Ltd.

Press and hold key: Store the current setting into the Hyper Memory “2.”

[3(WX)] key

Press key: Frequency entry digit “3.”

Press [MON/F] +: Recall the “Weather” broadcast channel.

Press and hold key: Store the current setting into the Hyper Memory “3.”

[4(ARTS)] key

Press key: Frequency entry digit “4.”

Press [MON/F] +: Activate the ARTS feature.

Press and hold key: Store the current setting into the Hyper Memory “4.”

[5(S.SCH)] key

Press key: Frequency entry digit “5.”

Press [MON/F] +: Activate the Smart Search feature.

Press and hold key: Store the current setting into the Hyper Memory “5.”

[6(SP-ANA)] key

Press key: Frequency entry digit “6.”

Press [MON/F] +: Activate the Spectrum Analyzer (Spectra-ScopeTM) feature.

Press and hold key: Store the current setting into the Hyper Memory “6.”

[7(CH.CNT)] key

Press key: Frequency entry digit “7.”

Press [MON/F] +: Activate the Channel Counter feature.

Press and hold key: Store the current setting into the Hyper Memory “7.”

[8(TONE)] key

Press key: Frequency entry digit “8.”

Press [MON/F] +: Activate the CTCSS or DCS operation.

Press and hold key: Store the current setting into the Hyper Memory “8.”

[9(SPCL)] key

Press key: Frequency entry digit “9.”

Press [MON/F] +: Enter the “Special Memory” mode.

Press and hold key: Store the current setting into the Hyper Memory “9.”

FCC ID: K66VX-7R

Operating Manual

Vertex Standard Co., Ltd.

[0(SET)] key

Press key: Frequency entry digit “0.”

Press [MON/F] +: Enter the “Set” (Menu) mode.

Press and hold key: Store the current setting into the Hyper Memory “9.”

[BAND(BND DN)] key

Press key: Move up the frequency band.

Press [MON/F] +: Move down the frequency band.

Press and Hold key: Move up the frequency band.

[V/M(WRITE MT)] key

Press key: Switches frequency control between VFO and Memory. System

Press [MON/F] +: None.

Press and hold key: ????.

[MON/F] key

Press key: Activate the “Alternate” key function.

Press [MON/F] +: None.

Press and hold key: ????.

[HM/RV(EMG)] key

Press key: Reverse the transmit and receive frequencies while working through a

repeater.

Press [MON/F] +: Switch to the “Home” (favorite frequency) Channel.

Press and hold key: Activate the EMERGENCY feature.

[%(TX PO LK)] key

Press key: Activate the Internet Connection feature.

Press [MON/F] +: Select the desired transmitter power output.

Press and hold key: Activate the Key Lock feature.

PTT Switch

Press key: Transmit

Press [MON/F] +: Temporary High Power Transmit.

Press and hold key: Transmit

FCC ID: K66VX-7R

Operating Manual

Vertex Standard Co., Ltd.

MON key

Press key: USA version; Disable the Noise and Tone Squelch.

European version; Activate the T.CALL.

Press [MON/F] +: Enter the squelch level setting mode.

[MAIN] key

Press key: Switch the Upper Frequency to the Operating Band.

Press [MON/F] +: Switches Upper Frequency display between Large Character and

Small Character mode.

Press and hold key: Activate the Dual Receive feature.

[SUB] key

Press key: Switch the Lower Frequency to the Operating Band.

Press [MON/F] +: Switches Lower Frequency display between Large Character and

Small Character mode.

Press and hold key: Activate the Dual Receive feature.

Accessories & Options

Accessories & OptionsAccessories & Options

Accessories & Options

Accessories Supplied with the

Accessories Supplied with theAccessories Supplied with the

Accessories Supplied with the VX-7R

VX-7R VX-7R

VX-7R

FNB-80LI Battery Pack (7.4V/1,300mAh)

NC-72B/C Battery Changer

Quick Draw Belt Clip

Hand Strap

Antenna

Operating Manual

Warranty Card

Available Options for your VX-

Available Options for your VX-Available Options for your VX-

Available Options for your VX-7R

7R7R

! CSC-

CSC-CSC-

CSC-88

8888

88 Soft Case

! CD-

CD-CD-

CD-15A

15A15A

15A Rapid Charger (requires NC-72B/C)

! FBA-23

FBA-23FBA-23

FBA-23 2 x “AA” Cell Battery Case (batteries not supplied)

! FNB-8

FNB-8FNB-8

FNB-80

0LI

LILI

LI Battery Pack

! E-DC-5B

E-DC-5BE-DC-5B

E-DC-5B DC Cable w/Noise Filter

! NC-72B/C

NC-72B/CNC-72B/C

NC-72B/C Battery Changer

FCC ID: K66VX-7R

Operating Manual

Vertex Standard Co., Ltd.

! E-DC-6

E-DC-6E-DC-6

E-DC-6 DC Cable; plug and wire only

! MH-

MH-MH-

MH-5

57A4B

7A4B7A4B

7A4B Speaker/Microphone

! CMP460

CMP460CMP460

CMP460 Waterproof Speaker/Microphone

! VC-

VC-VC-

VC-27

2727

27 Earpiece/Microphone

! CN-3

CN-3CN-3

CN-3 BNC-to-SMA Adapter

! SU-1

SU-1SU-1

SU-1 Barometric Pressure Sensor Unit

! CT-91

CT-91CT-91

CT-91 Microphone Adapter

Availability of accessories may vary. Some accessories are supplied as standard per local

requirements, while others may be unavailable in some regions. Consult your Yaesu

Dealer for details regarding these and any newly-available options. Connection of any

non-Yaesu-approved accessory, should it cause damage, may void the Limited Warranty

on this apparatus.

Installation of Accessories

Installation of AccessoriesInstallation of Accessories

Installation of Accessories

Antenna Installation

Antenna InstallationAntenna Installation

Antenna Installation

The supplied antenna provides good results over the entire frequency range of the

transceiver. However, for enhanced base station medium-wave and shortwave reception,

you may wish to connect an external (outside) antenna.

The supplied antenna consists of two sections: the “Base Antenna” (used for

operation above 50 MHz), and the “Extender Element” (used for monitoring of

frequencies below 50 MHz).

To install the supplied antenna

Hold the bottom end of the antenna, then screw it onto the mating connector on the

transceiver until it is snug. Do not over-tighten by use of extreme force.

When operating the VX-

VX-VX-

VX-7R

7R7R

7R on frequencies lower than the 50 MHz band, disconnect

the antenna cap from the base antenna then screw the Extender Element onto the Base

Antenna. Of cause, the VX-7R may be operate on frequencies higher than the 50 MHz

band while Extender Element is still attached onto the Base Antenna

Notes:

• Never transmit without having an antenna connected.

• When installing the supplied antenna, never hold the upper part of the antenna

while screwing it onto the mating connector on the transceiver.

FCC ID: K66VX-7R

Operating Manual

Vertex Standard Co., Ltd.

• If using an external antenna for transmission, ensure that the SWR presented to

the transceiver is 1.5:1 or lower.

• Take care not lose the antenna cap when removing it from the Base Antenna.

How to Quick Draw

How to Quick Draw How to Quick Draw

How to Quick Draw Belt Clip

Belt ClipBelt Clip

Belt Clip

1. Connect the hanger to the rear of the VX-

VX-VX-

VX-7R

7R7R

7R, with the notch pointing directly up,

using the supplied screw (Figure XX).

Use

Use Use

Use only

onlyonly

only the screw included with the clip to

the screw included with the clip to the screw included with the clip to

the screw included with the clip to

mount the clip to the back of the

mount the clip to the back of themount the clip to the back of the

mount the clip to the back of the

VX-7R!

VX-7R!VX-7R!

VX-7R!

2. Clip the Quick-Draw Belt Clip onto your belt (Figure xx).

3. To install the VX-

VX-VX-

VX-7R

7R7R

7R into the Quick-Draw Belt Clip, align the hanger with the

Quick-Draw Belt Clip, and slide the MAGNUM into its slot until a click is heard.

4. To remove the VX-

VX-VX-

VX-7R

7R7R

7R from the Quick-Draw Belt Clip, rotate the VX-

VX-VX-

VX-7R

7R7R

7R 180 degrees,

then slide the VX-

VX-VX-

VX-7R

7R7R

7R out from the Quick-Draw Belt Clip (Figure xx).

Installation of FNB-8

Installation of FNB-8Installation of FNB-8

Installation of FNB-80

0LI Battery Pack

LI Battery PackLI Battery Pack

LI Battery Pack

The FNB-80LI is a high-performance Lithium-Ion battery providing high capacity in

a very compact package. Under normal use, the FNB-80LI may be used for

approximately 300 charge cycles, after which operating time may be expected to

decrease. If you have an old battery pack which is displaying capacity which has become

diminished, you should replace the pack with a new one.

1. Push the bottom latch slightly to the “Open” position.

2. Install the FNB-80LI as shown in the illustration.

3. Re-lock the bottom plate by carefully pressing the hinged latch cover back into its

normal operating position.

If the battery has never been used, or its charge is depleted, it may be charged by

connecting the NC-72B/C Battery Charger, as shown in the illustration, to the EXT DC

jack. If only 12 ~ 16 Volt DC power is available, the optional E-DC-5B or E-DC-6 DC

Adapter (with its cigarette lighter plug) may also be used for charging the battery, as

shown in the illustration.

The display will indicate “NOW CHARGING” while the battery is being charged.

When charging is finished, the display will change to indicate “COMPLETE.”

Installation of FBA-23 (Option) Alkaline Battery Case

The optional FBA-23 Battery Case allows receive monitoring using two “AA” size

Alkaline batteries. Alkaline batteries can also be used for transmission in an emergency,

but power output will only be 300 mW, and battery life will be shortened dramatically.

FCC ID: K66VX-7R

Operating Manual

Vertex Standard Co., Ltd.

To Install Alkaline Batteries into the FBA-23

1. Slide the batteries into the FBA-23 as shown in the illustration, with the Negative

[–] side of the batteries touching the spring connections inside the FBA-23.

2. Unlock the bottom plate by pushing the latch in the “Open” direction.

3. Install the FBA-23 as shown in the illustration, with the [+] side facing the bottom

of the transceiver.

4. Re-lock the bottom plate by carefully pressing the latch cover back into its normal

operating position.

The FBA-23 does not provide connections for charging, since Alkaline cells cannot be

re-charged. Therefore, the NC-72B/C, E-DC-5B, or E-DC-6 may safely be connected to

the EXT DC jack when the FBA-23 is installed.

Notes:

• The FBA-23 is designed for use only with AA-type Alkaline cells.

• If you do not use the VX-

VX-VX-

VX-7R

7R7R

7R for a long time, remove the Alkaline batteries from the

FBA-23, as battery leakage could cause damage to the FBA-23 and/or the

transceiver.

Battery Life Information

When the battery charge is almost depleted, a “Low Voltage” indicator will appear on

the display. When this icon appears, it is recommended that you charge the battery

soon.

(1) TX 6 sec., RX 6 sec. and Squelched 48 sec.

(2) Continuous signal reception

The current battery voltage can be displayed manually on the LCD, by following the

instructions on page ??.

Battery capacity may be reduced during extremely cold weather operation. Keeping

the radio inside your parka may help preserve the full charge capacity.

AC Operation Using NC-72B/C (Receiving only)

AC Operation Using NC-72B/C (Receiving only)AC Operation Using NC-72B/C (Receiving only)

AC Operation Using NC-72B/C (Receiving only)

The VX-

VX-VX-

VX-7R

7R7R

7R may be operated from your house current by use of the supplied NC-72B/C

Battery Charger.

To use the NC-72B/C, turn the transceiver off, then plug the miniature connector of the

Battery Charger into the EXT DC jack on the side of the radio. Now plug the Battery

Charger into the wall outlet. You may now turn on the transceiver.

FCC ID: K66VX-7R

Operating Manual

Vertex Standard Co., Ltd.

Interface of Packet

Interface of Packet Interface of Packet

Interface of Packet TNCs

TNCsTNCs

TNCs

The VX-

VX-VX-

VX-7R

7R7R

7R may be used for Packet operation, using the optional CT-44 microphone

adapter (available from your Yaesu dealer) for easy interconnection to commonly-

available connectors wired to your TNC. You may also build your own cable using a

four-conductor miniature phone plug, per the diagram below.

The audio level from the receiver to the TNC may be adjusted by using the VOLUME

knob, as with voice operation. The input level to the VX-

VX-VX-

VX-7R

7R7R

7R from the TNC should be

adjusted at the TNC side; the optimum input voltage is approximately 5 mV at 2 k-ohm.

Be sure to turn the transceiver and TNC off before connecting the cables, so as to

prevent voltage spikes from possibly damaging your transceiver.

Operation

OperationOperation

Operation

R. F. say

R. F. sayR. F. say

R. F. say

:: Hi! I’m R. F. Radio, and I’ll be helping you along as you learn the many

features of the VX-

VX-VX-

VX-7R

7R7R

7R. I know you’re anxious to get on the air, but I encourage you to

read the “Operation” section of this manual as thoroughly as possible, so you’ll get the

most out of this fantastic new transceiver. Now. . .let’s get operating!

Switching Power On and Off

Switching Power On and OffSwitching Power On and Off

Switching Power On and Off

1. Be sure the battery pack is installed, and that the battery is fully charged. Connect

the antenna to the top panel ANTENNA jack.

2. Press and hold in the PWR switch (on the left side of the front panel) for 2 seconds.

Two beeps will be heard when the switch has been held long enough, and the

opening message will appear on the display, then frequency display will appear.

After another two seconds, the receive-mode Battery Saver function will become

active, unless you have disabled it (see page ??).

3. To turn the VX-

VX-VX-

VX-7R

7R7R

7R off, press and hold in the PWR switch again for 2 seconds.

R.F. says

R.F. saysR.F. says

R.F. says

: If you don’t hear the two “Beep” tones when the radio comes on, the Beeper

may have been disabled via the Menu system. See page ??, which tells you how to

reactivate the Beeper.

Adjusting the Volume Level

Adjusting the Volume LevelAdjusting the Volume Level

Adjusting the Volume Level

Rotate the VOLUME control (outer ring) to set the desired audio level. Clockwise

rotation increases the volume level.

FCC ID: K66VX-7R

Operating Manual

Vertex Standard Co., Ltd.

Squelch Adjustment

Squelch AdjustmentSquelch Adjustment

Squelch Adjustment

The VX-

VX-VX-

VX-7R

7R7R

7R’s Squelch system allows you to mute the background noise when no

signal is being received. Not only does the Squelch system make “standby” operation

more pleasant, it also significantly reduces battery current consumption.

The Squelch system may be adjusted independently for the FM and Wide-FM (FM

Broadcast) modes.

1. Press the [MON/F] key, then press the MONI switch on the left side of the radio.

This provides a “Short-cut” to Menu Item (Basic Setup #1: SQL NFM) or Menu Item

(Basic Setup #2: SQL WFM).

2. Now, press the [MAIN] or [SUB] key to set the background noise is just silenced

(typically at a setting of about “3” or “4” on the scale); this is point of maximum

sensitivity to weak signals.

3. When you are satisfied with the Squelch threshold setting, press the PTT key

momentarily to save the new setting and exit to normal operation.

4. You may also adjust the Squelch setting by using the “Set” (Menu) mode. See

page ?? for details.

. Say

Say Say

Say

: If you’re operating in an area of high RF pollution, you may need to consider

“Tone Squelch” operation using the built-in CTCSS Decoder. This feature will keep your

radio quiet until a call is received from a station sending a carrier which contains a

matching (subaudible) CTCSS tone. Or if your friends have radios equipped with DCS

(Digital Coded Squelch) like your VX-

VX-VX-

VX-7R

7R7R

7R has, try using that mode for silent monitoring

of busy channels.

Selecting the Operating Band

Selecting the Operating BandSelecting the Operating Band

Selecting the Operating Band

The VX-

VX-VX-

VX-7R

7R7R

7R covers an incredibly wide frequency range, over which a number of

different operating modes are used. Therefore, the VX-

VX-VX-

VX-7R

7R7R

7R’s frequency coverage has been

divided into different operating bands, each of which has its own pre-set channel steps

and operating modes. You can change the channel steps and operating modes later, if

you like (see page ??).

USA Version EXP VersionBAND

MAIN VFO SUB VFO MAIN VFO SUB VFO

BC Band 0.5-1.8 MHz --- 0.5-1.8 MHz ---

SW Band 1.8-30 MHz --- 1.8-30 MHz ---

FM BC Band 59-108 MHz --- 88-108 MHz ---

AIR Band 108-137 MHz --- 108-137 MHz ---

VHF-TV Band 174-222 MHz --- 174-222 MHz ---

Action Band 1 225-420 MHz --- 222-420 MHz ---

UHF TV Band 470-729 MHz --- 470-800 MHz ---

FCC ID: K66VX-7R

Operating Manual

Vertex Standard Co., Ltd.

Action Band 2 800-999 MHz --- 800-999 MHz ---

50 MHz Ham Band 30-59 MHz 50-54 MHz 30-88 MHz 50-54 MHz

144 MHz Ham Band 137-174 MHz 140-174 MHz 137-174 MHz 140-174 MHz

220 MHz Ham Band 222-225 MHz --- --- ---

430 MHz Ham Band 420-470 MHz 420-470 MHz 420-470 MHz 420-470 MHz

To Change Operating Bands

1. Press the [BAND(BND DN)] key repetitively. You will see the LCD indication move

up as you press the [BAND(BND DN)] key.

2. If you wish to move down the operating band, press the [MON/F] key, then press

the [BAND(BND DN)] key.

3. The VX-

VX-VX-

VX-7R

7R7R

7R uses a dual VFO system (explained in detail on page ??). To switch from

the “Main” VFO to the “Sub” VFO instantly, press the [SUB] key momentarily.

Pressing the [MAIN] key will return the VX-7R to “Main” VFO.

4. Once you have selected the desired band, you may initiate manual tuning (or

scanning) per the discussions below.

Frequency Navigation

Frequency NavigationFrequency Navigation

Frequency Navigation

The VX-

VX-VX-

VX-7R

7R7R

7R will initially be operating in the “VFO” mode, as just described. This is a

channelized system which allows free tuning throughout the currently-selected

operating band.

Three basic frequency navigation methods are available on the VX-

VX-VX-

VX-7R

7R7R

7R:

1) Tuning Dial

Rotation of the DIAL allows tuning in the pre-programmed steps established for the

current operating band. Clockwise rotation of the DIAL causes the VX-

VX-VX-

VX-7R

7R7R

7R to be tuned

toward a higher frequency, while counter-clockwise rotation will lower the operating

frequency.

If you press the [MON/F] key momentarily, then rotate the DIAL, frequency steps of 1

MHz will be selected. This feature is extremely useful for making rapid frequency

excursions over the wide tuning range of the VX-

VX-VX-

VX-7R

7R7R

7R.

2) Direct Keypad Frequency Entry

The desired operating frequency may be entered directly from the keypad.

The operating mode will automatically be set once the new frequency is entered via

the keypad.

To enter a frequency from the keypad, just press the numbered digits on the keypad in

the proper sequence. There is no “Decimal point” key on the VX-7R, so if the frequency

FCC ID: K66VX-7R

Operating Manual

Vertex Standard Co., Ltd.

is below 100 MHz (e.g. 15.150 MHz), any required leading zeroes must be entered.

However, there is a short-cut for frequencies ending in zero - press the [V/M(WRITE

MT)] key sfter the last non-zero digit.

Examples:

To enter 146.520 MHz, press [1] " [4] " [6] " [5] " [2] " [0]

To enter 15.255 MHz, press [0] " [1] " [5] " [2] " [5] " [5]

To enter 1.250 MHz (1250 kHz), press [0] " [0] " [1] " [2] " [5] " [0]

To enter 0.950 MHz (950 kHz), press [0] " [0] " [0] " [9] " [5] " [0]

To enter 430.000MHz, press [4] " [3] " [V/M(WRITE MT)]

3) Scanning

From the VFO mode, press the [MON/F] key, then press the [1(SCAN)] key. The VX-

VX-VX-

VX-

7R7R

7R will begin scanning toward a higher frequency, and will stop when it receives a

signal strong enough to break through the Squelch threshold. The VX-7R will then hold

on that frequency according to the setting of the “RESUME” mode (Menu Item: Scan

Modes #3). See page ?? for details.

If you wish to reverse the direction of the scan (i.e. toward a lower frequency, instead

of a higher frequency), just rotate the DIAL one click in the counter-clockwise direction

while the VX-7R is scanning. The scanning direction will be reversed. To revert to

scanning toward a higher frequency once more, rotate the DIAL one click clockwise.

Press the PTT switch momentarily to cancel the scanning.

Dual Receive Operation

Dual Receive OperationDual Receive Operation

Dual Receive Operation

The VX-7R may be operate dual frequency receive.

Press and hold the [MAIN] or [SUB] key for 2 second to activate the Dual Receive

operation.

While Dual Receive operation, “Main” band frequency display upper side and “Sub”

band frequency display lower side, and “Operating” band (enabling the transmit and

band/frequency change) indicate

large

characters.

To switch the “Operating” band, press the [MAIN] key momentarily to switch the

“Main” band frequency to the “Operating” band. Meanwhile, press the [SUB] key

momentarily to switch the “Sub” band frequency to the “Operating” band, described

previously.

R.F. Say

R.F. SayR.F. Say

R.F. Say

: The “Sub” band frequency is possible operate only on the amateur bands, but

you can select both bands to receive different frequencies

on the same bands.

FCC ID: K66VX-7R

Operating Manual

Vertex Standard Co., Ltd.

Audio Muting

The Audio Mute feature is useful in situations where it would be helpful to reduce

the audio level of the “Receive Only” receiver (

Small

character) whenever you receive a

signal on the “main” band (

Large

character) while Dual Receive operation.

To activate the Audio Mute feature:

1. Press the [MON/F] key, then press the [0(SET)] key to enter the Set mode.

2. Rotate the DIAL to select Menu Item (Basic Operation #8: MUTE SET).

3. Press the [MAIN] or [SUB] key to select “ON” (to enable Audio Mute feature).

4. Press the PTT switch to save the new setting and exit to normal operation.

5. To disable the Audio Mute feature, select “ON” in step 3 above.

When the Audio Mute feature is activated, the “M

M” icon will appear on the display.

BAND Linking

For operation on Amateur satellites which use a “normal” (not “inverted” FM

transponder, the BAND Link feature may be useful.

1. Set up dual receive operation, as just described.

2. Press the [MON/F] key, then press the [0(SET)] key to enter the Set mode.

3. Rotate the DIAL to select Menu Item (Misc Setup #9: BAND LINK).

4. Press the [MAIN] or [SUB] key to set this Menu Item to ON.

5. Press the PTT key to save the new setting and exit to Linked/Dual receive

operation.

As you rotate the DIAL, you will observe that both BAND frequencies are changing

together. When you are done with this operating mode, re-enter the Set mode, and set

(Misc Setup #9: BAND LINK) to OFF.

Transmission

TransmissionTransmission

Transmission

Once you have set up an appropriate frequency inside one of the three or four

Amateur bands on which the VX-7R can transmit (50 MHz, 144 MHz, or 430 MHz, plus

220 MHz on the USA version), you’re ready to transmit. These are the most basic steps;

more advanced aspects of transmitter operation will be discussed later.

1. To transmit, press the PTT switch, and speak into the front panel microphone

(located in the upper right-hand corner of the speaker grille) in a normal voice level.

The “I-Beam” will glow red during transmission.

2. To return to the receive mode, release the PTT switch.

3. During transmission, the relative power level will be indicated on the LCD. Full

power (5 Watts) is indicated by eight arrows below the frequency display. The three

FCC ID: K66VX-7R

Operating Manual

Vertex Standard Co., Ltd.

“Low Power” levels (L1, L2, and L3) are indicated by two, four, or six arrows,

respectively. Additionally, the “L1,” “L2,” or “L3” icon will appear at the bottom of

the display, corresponding with the “Low Power” Level setting.

. Say

Say Say

Say

: If you’re just talking to friends in the immediate area, you’ll get much longer

battery life by switching to Low Power operation. To do this, press the [MON/F] key,

then press the [%(TX PO LK)] key so that the “L” icon appears at the bottom of the

display. And don’t forget, always have an antenna connected when you transmit.

Transmission is not possible on any operating bands other than the 50 MHz, 144 MHz,

and 430 MHz bands.

Changing the Transmitter Power Level

You can select between a total of four transmitter power levels on your VX-7R. The

exact power output will vary somewhat, depending on the voltage supplied to the

transceiver. With the standard FNB-80LI Battery Pack and external DC source, the

power output levels available are:

HIGH LOW 3 LOW2 LOW1

50/144/430 MHz FM 5.0 W 2.5 W 1.0 W 0.5 W

50 MHz AM 1.0 W (Fixed)

220 MHz FM 0.3 W (Fixed)

To change the power level:

1. The default setting for the power output is “High;” in this configuration, the LCD

shows no indication of the power output level. Press the [MON/F] key, then press

the [%(TX PO LK)] key causes the power levels “L1,” “L2,” or “L3” appear.

2. Press the [MON/F] key, then press the [%(TX PO LK)] key until the “Low Power”

icon disappears will restore High Power operation.

. Say

Say Say

Say

: The VX-7R is smart! You can set up Low power on one band (like UHF), while

leaving VHF on High power, and the radio will remember the different settings on each

band. And when you store memories, you can store High and Low power settings

separately in each memory, so you don’t waste battery power when using very close-in

repeaters!

When you are operate on Low power setting, Press the [MON/F] key, then press the PTT

switch, the VX-7R temporarily.

VOX Operation

The VOX system provides automatic transmit/receive switching based on voice input

to the microphone. With the VOX system enabled, you do not need to press the PTT

FCC ID: K66VX-7R

Operating Manual

Vertex Standard Co., Ltd.

switch in order to transmit.

1. Press the [MON/F] key, then press the [0(SET)] key to enter the Set mode.

2. Rotate the DIAL to select the Menu Item (Misc Setup #7: VOX).

Press the [MAIN] or [SUB] key to select desired VOX level “HIGH” or “LOW.”

3. When you have made your choice, press the PTT key to save the new setting and

return to normal operation.

4. Without pressing the PTT switch, speak into the microphone in a normal voice level.

When you start speaking, the transmitter should be activated automatically. When

you finish speaking, the transceiver should return to the receive mode (after a short

delay).

5. To cancel VOX and return to PTT operation, just repeat the above procedures, select

“OFF” in step 3 above.

When the VOX system is activated, the “V

V” icon will appear on the display.

The VX-7R may be adjusted the “Hang-Time” of the VOX system (the transmit-receive

delay after the cessation of speech) via the Menu. The default delay is 1/2 second. To set

a different delay time:

1. Press the [MON/F] key, then press the [0(SET)] key to enter the Set mode.

2. Rotate the DIAL to select the Menu Item (Misc Setup #8: VOX DLAY).

3. Press the [MAIN] or [SUB] key to select the delay time among “0.5s,” “1s,” and “2s.”

4. When you have made your choice, press the PTT key to save the new setting and

return to normal operation.

AM Broadcast Reception

AM Broadcast ReceptionAM Broadcast Reception

AM Broadcast Reception

The VX-7R includes provision for reception of AM broadcasts, either on the standard

medium-wave (MW) broadcast band, or on the shortwave bands up to 16 MHz.

1. Set the VX-7R to the VFO mode

2. Press the [BAND(BND DN)] key (or Press [MON/F] " [BAND(BND DN)])

repetitively until you see a frequency in the frequency range desired. The MW

coverage is 0.5 MHz to 1.8 MHz, while the shortwave broadcast coverage is 1.8

MHz to 16 MHz. In either case, the operating mode (displayed on the right edge of

the LCD) should be shown as being “AM.”

3. Rotate the DIAL to tune across the broadcast band.

4. You may also use the keypad to enter frequencies directly. This method will be

quicker for changing from the 49-meter broadcast band to the 31-meter band, for

FCC ID: K66VX-7R

Operating Manual

Vertex Standard Co., Ltd.

example.

. Say

Say Say

Say

: If the operating mode is not correct, you may need to adjust the setting of

Menu Item (Basic Setup #4: RX MODE). See page ?? for details.

The VX-7R is stored the frequency of the Short-wave Broadcast station into the memory

channel “???” through “???.”

AM Aircraft Reception

AM Aircraft ReceptionAM Aircraft Reception

AM Aircraft Reception

Reception of AM signals in the aeronautical band (108-137 MHz) is similar to that

described in the previous section.

1. Be sure that the VX-7R is set to the VFO mode.

2. Press the [BAND(BND DN)] key (or Press [MON/F] " [BAND(BND DN)])

repetitively until you see a frequency in the aeronautical band.

3. Rotate the DIAL to tune across the aeronautical band.

4. You may also use the keypad to enter frequencies directly. Remember that

frequencies quoted by aircraft operators may be abbreviated, and that the “5” at the

end of a frequency may be dropped. Since aeronautical channels are assigned in

25-kHz steps, therefore, a frequency announced as “thirty-two, forty-two”

corresponds to an operating frequency of 132.425 MHz.

FM Broadcast/TV Audio Reception

FM Broadcast/TV Audio ReceptionFM Broadcast/TV Audio Reception

FM Broadcast/TV Audio Reception

The VX-7R also includes provision for reception in the FM broadcast band, utilizing a

wide-bandwidth filter which provides excellent fidelity.

To Activate FM Broadcast Reception

1. Be sure that the VX-7R is set to the VFO mode.

2. Press the [BAND(BND DN)] key (or Press [MON/F] " [BAND(BND DN)])

repetitively until a frequency in the FM broadcast band appears on the display. The

total frequency range included in the “FM” band is 59-108 MHz.

3. Rotate the DIAL to select the desired station. The default synthesizer steps for the

W-FM mode are 100 kHz/step.

To Activate VHF or UHF TV Audio Reception

1. Be sure that the VX-7R is set to the VFO mode.

2. Press the [BAND(SET)AR] key repetitively until a frequency in the VHF or UHF

TV bands appears on the LCD.

FCC ID: K66VX-7R

Operating Manual

Vertex Standard Co., Ltd.

3. Rotate the DIAL to select the desired station.

. Say

Say Say

Say

: Remember that the Wide-FM Squelch setting may be made independently

from the Narrow-FM setting, using Menu Item (Basic Setup #2: SQL WFM). See

page ??.

Weather Broadcast

Weather BroadcastWeather Broadcast

Weather Broadcast/VHF Marine Channel

/VHF Marine Channel/VHF Marine Channel

/VHF Marine Channel Reception

Reception Reception

Reception

The VX-7R includes a unique feature which allows reception of weather broadcasts

in the 160-MHz frequency range. Ten standard Weather Broadcast channels are pre-

loaded into a special memory bank.

To listen to a Weather Broadcast Channel/VHF Marine Channel:

1. Press the [MON/F] key, then press the [3(WX)] key to recall the Weather Broadcast

channels.

2. Turn the DIAL knob to select the desired Weather Broadcast channel.

3. If you wish to check the other channels for activity by scanning, press the [MON/F]

key then press the [1(SCAN)] key.

4. Press the [3(WX)] key again to recall the VHF Marine Channels. Turn the DIAL

knob to select the desired Marine channel.

5. To exit to normal operation, again the [MON/F] key, then press the [3(WX)] key.

Operation will return to the VFO or Memory channel you were operating on before

you began Weather Broadcast operation.

R.F. Say

R.F. SayR.F. Say

R.F. Say

: In the event of extreme weather disturbances, such as storms and hurricanes,

the NOAA (National Oceanic and Atmospheric Administration) sends a weather alert

accompanied by a 1050 Hz tone and subsequent weather report on one of the NOAA

weather channels. You may disable the Weather Alert feature via Menu Item (Misc

Setup #20 WX ALERT), if desired.

Keyboard Locking

Keyboard LockingKeyboard Locking

Keyboard Locking

In order to prevent accidental frequency change or inadvertent transmission, various

aspects of the VX-7R’s keys and switches may be locked out. The possible lockout

combinations are:

KEY: Just the front panel keys are locked out

DIAL: Just the top panel DIAL is locked out

KEY + DIAL: Both the DIAL and Keys are locked out

PTT: The PTT switch is locked (TX not possible)

KEY + PTT: Both the keys and PTT switch are locked out

FCC ID: K66VX-7R

Operating Manual

Vertex Standard Co., Ltd.

DIAL + PTT: Both the DIAL and PTT switch are locked out

ALL: All of the above are locked out

To lock out some or all of the keys:

1. Press the [MON/F] key, then press the [0(SET)] key to enter the Set mode.

2. Rotate the DIAL to select Menu Item (Basic Setup #10: LOCK MODE).

3. Press the [MAIN] or [SUB] key to choose between one of the locking schemes as

outlined above.

4. When you have made your selection, press the PTT switch to save the new setting

and resume normal operation.

5. To activate the locking feature, press and hold in the [%(TX PO LK)] key for 2

seconds. The “Key Lock” icon will appear on the LCD. To cancel locking, again press

and hold the [%(TX PO LK)] key for 2 seconds.

Say

SaySay

Say

: Even when “ALL” keys have been locked out, one key actually is not locked

out: the [%(TX PO LK)] key remains available so you can Unlock your keypad when you

want to!

Keypad/LCD Illumination

Keypad/LCD IlluminationKeypad/LCD Illumination

Keypad/LCD Illumination

Your VX-7R includes a reddish illumination lamp which aids in nighttime operation.

The red illumination yields clear viewing of the display in a dark environment, with

minimal degradation of your night vision. Three options for activating the lamp are

provided:

KEY Mode: Illuminate the Keypad/LCD for five seconds when any key pressed.

CONTINUE Mode: Illuminate the Keypad/LCD continuously.

OFF Mode: Disables the Keypad/LCD lamp.

Here is the procedure for setting up the Lamp mode:

1. Press the [MON/F] key, then press the [0(SET)] key to enter the Set mode.

2. Rotate the DIAL to select Menu Item (Display Setup #5: LAMP MODE).

3. Press the [MAIN] or [SUB] key to select one of the three modes described above.

4. When you have made your choice, press the PTT key to save the new setting and

return to normal operation.

Disabling the Keypad Beeper

Disabling the Keypad BeeperDisabling the Keypad Beeper

Disabling the Keypad Beeper

If the keypad’s Beeper creates an inconvenience (particularly when operating in a

quiet room), it may easily be disabled.

1. Press [MON/F] then, press the [0(SET)] key to enter the Set mode.

FCC ID: K66VX-7R

Operating Manual

Vertex Standard Co., Ltd.

2. Rotate the DIAL to select Menu Item (Basic Setup #9: KEY BEEP).

3. Press the [MAIN] or [SUB] key to change the setting from ON to OFF.

4. When you have made your selection, press the PTT key to save the new setting and

exit to normal operation.

5. If you wish to re-enable the Beeper, just repeat the above procedure, pressing the

[MAIN] or [SUB] key to select ON in step “3” above.

Advanced Operation

Advanced OperationAdvanced Operation

Advanced Operation

Now that you’re mastered the basics of VX-7R operation, let’s learn more about some

of the really neat features.

Setting the Frequency Display Image Size

Setting the Frequency Display Image SizeSetting the Frequency Display Image Size

Setting the Frequency Display Image Size

VFO Mode

When operating in the VFO mode, press the [MON/F] key, then press the [MAIN] or

[SUB] key causes the LCD to “toggle” between display of

large

largelarge

large

characters and the

small

smallsmall

small

characters. However, this feature does not activate while Dual Receive operation.

Memory Mode

When operating in the Memory mode (see page ??), press the [MON/F] key, then press

the [MAIN] or [SUB] key causes the LCD to “toggle” between display of the (large

characters) current memory’s frequency and the (small characters) current memory’s

frequency with alpha numeric Tag. However, this feature does not activate while Dual

Receive operation.

Changing the Channel Steps

Changing the Channel StepsChanging the Channel Steps

Changing the Channel Steps

The VX-7R’s synthesizer provides the option of utilizing channels steps of

5/9/10/12.5/15/20/25/50/100 kHz per step, any number of which may be important to

your operating requirements. The VX-7R is set up at the factory with different default

steps on each operating band which probably are satisfactory for most operation.

However, if you need to change the channel step increments, the procedure to do so is

very easy.

1. Press the [MON/F] key, then press the [0(SET)] key to enter the Set mode.

2. Rotate the DIAL to select Menu Item (Basic Setup #3: VFO STEP).

3. Press the [MAIN] or [SUB] key to select the new channel step size.

4. Press the PTT key to save the new setting and exit to normal operation.

FCC ID: K66VX-7R

Operating Manual

Vertex Standard Co., Ltd.

Changing the Operating Mode

Changing the Operating ModeChanging the Operating Mode

Changing the Operating Mode

The VX-7R provides for automatic mode changing when the radio is tuned to

different operating frequencies. However, should an unusual operating situation arise

in which you need to change between the available operating modes (FM-Narrow, FM-

Wide, and AM), here is the procedure for doing so:

1. Press the [MON/F] key, then press the [0(SET)] key to enter the Set mode.

2. Rotate the DIAL to select Menu Item (Basic Setup #4: RX MODE).

3. Press the [MAIN] or [SUB] key to select the new channel step size. The available

selections are:

AUTO: Automatic mode setting per default values.

N-FM: Narrow-bandwidth FM (used for voice communication)

W-FM: Wide-bandwidth FM (used for high-fidelity broadcasting)

AM: Amplitude Modulation

4. Press the PTT key to save the new setting and exit to normal operation.

. Say

Say Say

Say

: Unless you have a compelling reason to do so, leave the Automatic Mode

Selection feature on so as to save time and trouble when changing bands. If you make a

mode change for a particular channel or station, you can always store that one channel

into memory, as the mode setting will be memorized along with the frequency

information.

Repeater Operation

Repeater OperationRepeater Operation

Repeater Operation

Repeater stations, usually located on mountaintops or other high locations, provide a

dramatic extension of the communication range for low-powered hand-held or mobile

transceivers. The VX-7R includes a number of features which make repeater operation

simple and enjoyable.

Repeater Shifts

Your VX-7R has been configured, at the factory, for the repeater shifts customary in

your country. For the 50 MHz band, this usually will be 1 MHz, while the 144 MHz shift

will be 600 kHz; on 70 cm, the shift may be 1.6 MHz, 7.6 MHz, or 5 MHz (USA version).

Depending on the part of the band in which you are operating, the repeater shift may be

either downward (–) or upward (+), and one of these icons will appear at the top of the

LCD when repeater shifts have been enabled.

Automatic Repeater Shift (ARS)

FCC ID: K66VX-7R

Operating Manual

Vertex Standard Co., Ltd.

The VX-7R provides a convenient Automatic Repeater Shift feature, which causes

the appropriate repeater shift to be automatically applied whenever you tune into the

designated repeater sub-bands in your country. These sub-bands are shown below.

If the ARS feature does not appear to be working, you may have accidentally disabled

it.

To re-enable ARS:

1. Press the [MON/F] key, then press the [0(SET)] key to enter the Set mode.

2. Rotate the DIAL to select Menu Item (Basic Setup #5: ARS).

3. Press the [MAIN] or [SUB] key to select “ON” (to enable Automatic Repeater Shift).

4. Press the PTT key to save the new setting and exit to normal operation.

Manual Repeater Shift Activation

If the ARS feature has been disabled, or if you need to set a repeater shift other than

that established by the ARS, you may set the direction of the repeater shift manually.

To do this:

1. Press the [MON/F] key, then press the [0(SET)] key to enter the Set mode.

2. Rotate the DIAL to select Menu Item (Basic Setup #7: RPT SHIFT).

3. Press the [MAIN] or [SUB] key to select the desired shift among the “–RPT,”

“+RPT,” and “SIMP.”

4. Press the PTT key to save the new setting and exit to normal operation.

Changing the Default Repeater Shifts

If you travel to a different country, you may need to change the default repeater shift

so as to ensure compatibility with local operating requirements.

To do this, follow the procedure below:

1. Press the [MON/F] key, then press the [0(SET)] key to enter the Set mode.

2. Rotate the DIAL to select Menu Item (Basic Setup #6: SHIFT).

3. Press the [MAIN] or [SUB] key to select the new repeater shift magnitude.

4. Press the PTT key to save the new setting and exit to normal operation.

. Say

Say Say

Say

: If you just have one “odd” split that you need to program, don’t change the

“default” repeated shifts using this Menu Item! Enter the transmit and receive

frequencies separately, as shown on page ??.

When setting a large repeater shift (e.g. 5.0 MHz for 440 MHz), remember that you can

tune in 1 MHz steps by pressing [MON/F] key, then pressing the [MAIN] or [SUB] key

(first step entry: “MHz” icon will blinks).

FCC ID: K66VX-7R

Operating Manual

Vertex Standard Co., Ltd.

Checking the Repeater Uplink (Input) Frequency

It often is helpful to be able to check the uplink (input) frequency of a repeater, to see

if the calling station is within direct (“Simplex”) range.

To do this, just press the [HM/RV(EMG)] key. You’ll notice that the display has

shifted to the repeater uplink frequency. Press the [HM/RV(EMG)] key again to cause

operation to revert to normal monitoring of the repeater downlink (output) frequency.

CTCSS Operation

CTCSS OperationCTCSS Operation

CTCSS Operation

Many repeater systems require that a very-low-frequency audio tone be

superimposed on your FM carrier in order to activate the repeater. This helps prevent

false activation of the repeater by radar or spurious signals from other transmitters.

This tone system, called “CTCSS” (Continuous Tone Coded Squelch System), is included

in your VX-7R, and is very easy to activate.

. Say

Say Say

Say

: CTCSS setup involves two actions: setting the Tone Frequency and then

setting of the Tone Mode. These actions are set up by using the [8(TONE)] key, or Menu

Items (TSQ/DCS/DTMF #1: SQL TYPE) and (TSQ/DCS/DTMF #2: TONE SET).

1. Press the [MON/F] key, then press the [8(TONE)] key. This provides a “Short-cut”

to Menu Item (TSQ/DCS/DTMF #1: SQL TYPE).

2. Press the [MAIN] or [SUB] key so that “TONE” appears on the display; this

activates the CTCSS Encoder, which allows repeater access.

. Say

Say Say

Say

: You may notice an additional “DCS” icon appearing while you press the

[MAIN] or [SUB] key in this step. We’ll discuss the Digital Code Squelch system

shortly.

3. Press the [MAIN] key in step “2” above will occasionally cause “SQL” to appear

adjacent to the “TONE.” When “TONE SQL” appears, this means that the Tone

SQueLch system is active, which mutes your VX-7R’s receiver until it receives a call

from another radio sending out a matching CTCSS tone. This can help keep your

radio quiet until a specific call is received, which may be helpful while operating in

congested areas.

4. When you have made your selection of the CTCSS tone mode, rotate the DIAL one

click clockwise to select Menu Item (TSQ/DCS/DTMF #2: TONE SET). This Menu

selection allows setting of the CTCSS tone frequency to be used.

5. Press the [BAND(BND DN)] key to enable the adjustment of the CTCSS frequency.

6. Press the [MAIN] or [SUB] key until the display indicates the Tone Frequency you

need to be using (ask the repeater owner/operator if you don’t know the tone

frequency).

FCC ID: K66VX-7R

Operating Manual

Vertex Standard Co., Ltd.

7. When you have made your selection, press the [BAND(BND DN)] key, then press

the PTT switch to save the new settings and exit to normal operation.

. Say

Say Say

Say

: Some repeaters may or may not re-transmit a CTCSS tone - some systems just

use CTCSS to control access to the repeater, but don’t pass it along when transmitting.

If the S-Meter indicats, but the VX-7R is not passing audio, repeat steps “1” through “3”

above, but rotate the DIAL so that “SQL” disappears - this will allow you to hear all

traffic on the channel being received.

DCS Operation

DCS OperationDCS Operation

DCS Operation

Another form of tone access control is Digital Code Squelch, or DCS. It is a newer,

more advanced tone system which generally provides more immunity from false paging

than does CTCSS. The DCS Encoder/Decoder is built into your VX-7R, and operation is

very similar to that just described for CTCSS. Your repeater system may be configured

for DCS; if not, it is frequently quite useful in Simplex operation if your friend(s) use

transceivers equipped with this advanced feature.

. Say

Say Say

Say

: Just as in CTCSS operation, DCS requires that you set the Tone Mode to DCS

and that you select a tone code.

1. Press the [MON/F] key, then press the [8(TONE)] key. This provides a “Short-cut”

to Menu Item (TSQ/DCS/DTMF #1: SQL TYPE).

2. Press the [MAIN] or [SUB] key until “DCS” appears on the display; this activates

the DCS Encoder/Decoder.

3. Now rotate the DIAL to select Menu Item (TSQ/DCS/DTMF #3: DCS SET).

4. Press the [BAND(BND DN)] key to enable the adjustment of the DCS code.

5. Press the [MAIN] or [SUB] key to select the desired DCS Code (a three-digit

number). Ask the repeater owner/operator if you don’t know DCS Code; if you are

working simplex, just set up the DCS Code to be the same as that used by your

friend(s).

6. When you have made your selection, press the [BAND(BND DN)] key, then press

the PTT switch to save the new settings and exit to normal operation.

. Say

Say Say

Say

: Remember that the DCS is an Encode/Decode system, so your receiver will

remain muted until a matching DCS code is received on an incoming transmission.

Switch the DCS off when you’re just tuning around the band!

Tone Search Scanning

Tone Search ScanningTone Search Scanning

Tone Search Scanning

In operating situations where you don’t know the CTCSS or DCS tone being used by

another station or stations, you can command the radio to listen to the incoming signal

FCC ID: K66VX-7R

Operating Manual

Vertex Standard Co., Ltd.

and scan in search of the tone being used. Two things must be remembered in this

regard:

# You must be sure that your repeater uses the same tone type (CTCSS vs. DCS).

# Some repeaters do not pass the CTCSS tone; you may have to listen to the

station(s) transmitting on the repeater uplink (input) frequency in order to allow

Tone Search Scanning to work.

To scan for the tone in use:

1. Set the radio up for either CTCSS or DCS Decoder operation (see the previous

discussion). In the case of CTCSS, “TSQL” will appear on the display; in the case of

DCS, “DCS” will appear on the display.

2. Press the [MON/F] key, then press the [0(SET)] key to enter the Set mode.

3. Rotate the DIAL to select the Menu Item (TSQ/DCS/DTMF #2: TONE SET) when

TONE SQL is selected or Menu Item (TSQ/DCS/DTMF #3: DCS SET) during DCS

operation.

4. Press the [BAND(BND DN)] key to enable the Menu Item.

5. Press the [MON/F] key, then press the [1(SCAN)] key to start scanning for the

incoming CTCSS or DCS tone/code.

6. When the radio detects the correct tone or code, it will halt on that tone/code, and

audio will be allowed to pass. Press the [BAND(BND DN)] key to lock in that

tone/code, then press PTT to exit to normal operation.

. Say

Say Say

Say

: f the Tone Scan feature does not detect a tone or code, it will continue to scan

indefinitely. When this happens, it may be that the other station is not sending any tone.

You can press the PTT switch to halt the scan at any time.

You also can press the MONI key during Tone Scanning to listen to the (muted) signal

from the other station. When you release the MONI key, Tone Scanning will resume

after about a second.

Tone Scanning works either in the VFO or Memory modes.

CTCSS/DCS Bell Operation

CTCSS/DCS Bell OperationCTCSS/DCS Bell Operation

CTCSS/DCS Bell Operation

During CTCSS Decode or DCS operation, you may set the VX-7R up such that a ringing

“bell” sound alerts you to the fact that a call is coming in. Here is the procedure for

activating the CTCSS/DCS Bell:

1. Set the transceiver up for CTCSS Decode (“Tone Squelch”) or DCS operation, as

described previously.

2. Adjust the operating frequency to the desired channel.

FCC ID: K66VX-7R

Operating Manual

Vertex Standard Co., Ltd.

3. Press the [MON/F] key, then press the [0(SET)] key to enter the Set mode.

4. Rotate the DIAL to select Menu Item (TSQ/DCS/DTMF #5: BELL).

5. Press the [MAIN] or [SUB] key to set the desired number of rings of the Bell. The

available choices are 1, 3, 5, or 8 rings, REPEAT (continuous ringing), or OFF.

6. Press the PTT key momentarily to save the new setting and exit to normal

operation.

When a station calls you whose transceiver is sending a CTCSS tone or DCS code which

matches that set into your Decoder, the Bell will ring in accordance to this

programming.

Split Tone Operation

Split Tone OperationSplit Tone Operation

Split Tone Operation

The VX-7R can be operate Split Tone operation via Set mode.

1. Press the [MON/F] key, then press the [0(SET)] key to enter the Set mode.

2. Rotate the DIAL to select Menu Item (TSQ/DCS/DTMF #6: SPLIT TONE).

3. Press the [MAIN] or [SUB] key to set the desired number of rings of the Bell.

4. Press the PTT key momentarily to save the new setting and exit to normal

operation.

When the Split Tone feature is activated, you can see the following additional

parameters after the “DCS” parameter while selecting the Menu Item (TSQ/DCS/DTMF

#6: SQL TYPE),:

D CODE: DSC Encode only (“D” icon will appear while operating)

TONE DC: Encode the CTCSS Tone and Decode the DCS code

(“T∙D” icon will appear while operating)

DC TONE: Encode the DCS code and Decode the CTCSS Tone

(“D∙T” icon will appear while operating)

Select the desired operating mode above.

Tone Calling (1750 Hz)

Tone Calling (1750 Hz)Tone Calling (1750 Hz)

Tone Calling (1750 Hz)

If the repeaters in your country require a 1750-Hz burst tone for access (typically in

Europe), you can set the MONI key to serve as a “Tone Call” switch instead. To change

the configuration of this switch, we again use the Menu to help us.

1. Press the [MON/F] key, then press the [0(SET)] key to enter the Set mode.

2. Rotate the DIAL to select Menu Item (Misc Setup #3 MON/T-CAL).

3. Press the [MAIN] or [SUB] key to select “T-CALL” on the display.

4. Press the PTT key to save the new setting and exit to normal operation.

FCC ID: K66VX-7R

Operating Manual

Vertex Standard Co., Ltd.

5. To access a repeater, press and hold in the MONI key for the amount of time

specified by the repeater owner/operator. The transmitter will automatically be

activated, and a 1750-Hz audio tone will be superimposed on the carrier. Once

access to the repeater has been gained, you may release the MONI key, and use the

PTT key for activating the transmitter.

ARTS (Automatic Range Transponder System)

ARTS (Automatic Range Transponder System)ARTS (Automatic Range Transponder System)

ARTS (Automatic Range Transponder System)

The ARTS feature uses DCS signaling to inform both parties when you and another

ARTS-equipped station are within communications range. This may be particularly

useful during Search-and Rescue situations, where is important to stay in contact with

other members of your group.

Both stations must set up their DCS codes to the same code number, then activate

their ARTS feature using the command appropriate for their radio. Alert ringers may be

activated, if desired.

Whenever you push the PTT, or every 25 (or 15) seconds after ARTS is activated,

your radio will transmit a signal which includes a (subaudible) DCS signal for about 1

second. If the other radio is in range, the beeper will sound (if enabled) and the display

will show “IN RANGE” as opposed to the out of range display “OUT RANGE” in which

ARTS operation begins.

Whether you talk or not, the polling every 15 or 25 seconds will continue until you

de-activate ARTS. Every 10 minutes, moreover, you can have your radio transmit your

callsign via CW, so as to comply with identification requirements. When ARTS is de-

activated, DCS will also be deactivated (if you were not using it previously in non-ARTS

operation).

If you move out of range for more than one minute (four pollings), your radio will

sense that no signal has been received, three beeps will sound, and the display will

revert to “OUT RANGE.” If you move back into range, your radio will again beep, and

the display will change back to the “IN RANGE” indication.

During ARTS operation, your operating frequency will continue to be displayed, but

no changes may be made to it or other settings; you must terminate ARTS in order to

resume normal operation. This is a safety feature designed to prevent accidental loss of

contact due to channel change, etc.

Here is how to activate ARTS:

FCC ID: K66VX-7R

Operating Manual

Vertex Standard Co., Ltd.

Basic ARTS Setup and Operation

1. Set your radio and the other radio(s) to the same DCS code number, per the

discussion on page ??.

2. Press the [MON/F] key, then press the [4(ARTS)] key. You will observe the “OUT

RANGE” display on the LCD below the operating frequency. ARTS operation has

now commenced.

3. Every 25 seconds, your radio will transmit a “polling” call to the other station.

When that station responds with its own ARTS polling signal, the display will

change to “IN RANGE” to confirm that the other station’s polling code was received

in response to yours.

4. Press the [MON/F] key, then press the [4(ARTS)] key to exit ARTS operation and

resume normal functioning of the transceiver.

. Say

Say Say

Say

: ARTS won’t work if you have used the Lock feature to disable the PTT!

ARTS Polling Time Options

The ARTS feature may be programmed to poll every 25 seconds (default value) or 15

seconds. The default value provides maximum battery conservation, because the polling

signal is sent out less frequently. To change the polling interval:

1. Press the [MON/F] key, then press the [0(SET)] key to enter the Set mode.

2. Rotate the DIAL to select Menu Item (ARTS #2: ARTS ITVL).

3. Press the [MAIN] or [SUB] key to select the desired polling interval (15 or 25

seconds).

4. When you have made your selection, press the PTT key to save the new setting and

exit to normal operation.

ARTS Alert Beep Options

The ARTS feature allows two kinds of alert beeps (with the additional option of

turning them off), so as to alert you to the current status of ARTS operation. Depending

on your location and the potential annoyance associated with frequent beeps, you may

choose the Beep mode which best suits your needs. The choices are:

IN RANGE: The beeps are issued only when the radio first confirms that you are

within range, but does not re-confirm with beeps thereafter.

ALWAYS: Every time a polling transmission is received from the other station,

the alert beeps will be heard.

OFF: No alert beeps will be heard; you must look at the display to confirm

current ARTS status.

FCC ID: K66VX-7R

Operating Manual

Vertex Standard Co., Ltd.

To set the ARTS Beep mode, use the following procedure:

1. Press the [MON/F] key, then press the [0(SET)] key to enter the Set mode.

2. Rotate the DIAL to select Menu Item (ARTS #1: ARTS BEEP”).

3. Press the [MAIN] or [SUB] key to select the desired ARTS Beep mode (see above).

4. When you have made your selection, press the PTT key to save the new setting and

exit to normal operation.

CW Identifier Setup

The ARTS feature includes a CW identifier, as discussed previously. Every ten

minutes during ARTS operation, the radio can be instructed to send “DE (your callsign)

K” if this feature is enabled. The callsign field may contain up to 16 characters.

Here’s how to program the CW Identifier:

1. Press the [MON/F] key, then press the [0(SET)] key to enter the Set mode.

2. Rotate the DIAL to select Menu Item (ARTS #3: CW ID).

3. Press the [BAND(BND DN)] key to enable changing of this Menu item. Appear the

“ ” with blinking.

4. Press the [MAIN] or [SUB] key to set the CW ID function ON.

5. Rotate the DIAL one click clockwise to begin entry of the letters and numbers in

your callsign.

6. Press the [MAIN]/[SUB] key or keyboard to set the first letter or number in your

callsign.

Example 1: Press the [MAIN] or [SUB] key to select any of ?? available characters

(including letters, numbers, and special symbols).

Example 2: Press the [2(DW)] key repeatedly to toggle among the seven available

characters: A " B " C " a " b " c " 2

7. When the correct character has been selected, rotate the DIAL one click clockwise

to move on to the next character.

8. Repeat steps 6 and 7 as many times as necessary to complete your callsign. Note

that the “slant bar” (– • • – • is among the available characters, should you be a

“portable” station.

9. When you have entered your entire callsign, press the [BAND(BND DN)] key to

define the callsign, then press the PTT key to save the settings and exit to normal

operation.

FCC ID: K66VX-7R

Operating Manual

Vertex Standard Co., Ltd.

DTMF Operation

DTMF OperationDTMF Operation

DTMF Operation

The VX-7R’s 16-button keypad allows easy DTMF dialing for Autopatch or repeater

control purposes. Besides numerical digits [0] through [9], the keypad includes the [*]

and [#] digits, plus the [A], [B], [C], and [D] tones often used for repeater control.

Manual DTMF Tone Generation

You can generate DTMF tones during transmission manually.

1. Press the PTT switch to begin transmission.

2. While transmitting, press the desired numbers on the keypad.

3. When you have sent all the digits desired, release the PTT key.

DTMF Autodialer

Nine DTMF Autodial memories are provided, allowing you to store telephone numbers

for autopatch use. You can also store short autopatch access code streams so as to avoid

having to send them manually.

Here is the DTMF Autodial storage procedure:

1. Press the [MON/F] key, then press the [0(SET)] key to enter the Set mode.

2. Rotate the DIAL to select Menu Item (TSQ/DCS/DTMF #8: DTMF SET).

3. Press the [BAND(BAND DN)] key to enable adjustment of this Menu Item.

4. Press the [MAIN] or [SUB] key to select the DTMF Memory register into which you

wish to store this DTMF string.

5. Rotate the DIAL knob one click to begin DTMF Memory entry into the selected

6. Key in the DTMF digits you wish to store into this register.

Press the [MAIN] key to store the “Pause,” then press again the [MAIN] key to

delete the previously storing data after the cursor.

7. Press the PTT switch to save the setting. To store other numbers, repeat this

process, using a different DTMF memory register.

To send the telephone number:

1. Press the [MON/F] key, then press the [0(SET)] key to enter the Set mode.

2. Rotate the DIAL to select Menu Item (TSQ/DCS/DTMF #7: DTMF DIALER).

3. Press the [MAIN] or [SUB] key to set the DTMF Autodialer function to the “ON”

position.

4. Press the PTT switch to exit to normal operation and activates the DTMF

Autodialer function (“Telephone” icon will appear).

FCC ID: K66VX-7R

Operating Manual

Vertex Standard Co., Ltd.

5. In the Autodialer function mode, press the numerical key ([1] through [9])

corresponding to the DTMF memory string you wish to send. Once the string begins,

you may release the PTT key, as the transmitter will be held “on the air” until the

DTMF string is completed.

Emergency Channel Operation

Emergency Channel OperationEmergency Channel Operation

Emergency Channel Operation

The VX-7R includes an “Emergency” feature which may be useful if you have

someone monitoring on the same frequency as your transceiver’s UHF “Home” channel.

See page ?? for details on setting the Home channel.

The “Emergency” feature is activated by pressing the [HM/RV(EMG)] key for 2

seconds.

When this is done, the radio (A) is placed on the UHF amateur band Home channel,

(B) emits a loud “Alarm” sound (the volume is controlled by the VOLUME knob), (C)

flash the I-Beam by various color, and (D) if you press the PTT key, this alarm sound

will be transmitted.

To disable the “Emergency” feature, turn the radio by press and holding in the [PWR]

switch for 2 seconds.

Use this feature if you are out for a walk and want a quick way of alerting a family

member as to a dangerous situation. The alarm sound may discourage an attacker and

allow you to escape.

. Say

Say Say

Say

: Be sure to arrange with a friend or family member to be monitoring on the

same frequency, as there will be no identification sent via the Emergency alarm sound.

And do not transmit the alarm tone except in a true emergency!

The I-Beam may change to another function via Menu Item (Misc Setup #5: EMG SET),

see page xx.

ATT (Front End

ATT (Front End ATT (Front End

ATT (Front End Attenuator)

Attenuator)Attenuator)

Attenuator)

The attenuator will reduce all signals (and noise) by 20 dB, and it may be used to

make reception more pleasant under extremely noisy conditions.

1. Press [MON/F] then, press the [0(SET)] key to enter the Set mode.

2. Rotate the DIAL to select Menu Item (Misc Setup #18: ATT).

3. Press the [MAIN] or [SUB] key to change the setting from OFF to ON.

4. When you have made your selection, press the PTT key to save the new setting and

exit to normal operation.

5. If you wish to disable the attenuator, just repeat the above procedure, pressing the

[MAIN] or [SUB] key to select OFF in step “3” above.

FCC ID: K66VX-7R

Operating Manual

Vertex Standard Co., Ltd.

R.F. Say

R.F. SayR.F. Say

R.F. Say

: When the attenuator is activated, the “AT

ATAT

AT” icon will appear on the display.

Receive Battery Saver Setup

Receive Battery Saver SetupReceive Battery Saver Setup

Receive Battery Saver Setup

An important feature of the VX-7R is its Receive Battery Saver, which “puts the

radio to sleep” for a time interval, periodically “waking it up” to check for activity. If

somebody is talking on the channel, the VX-7R will remain in the “active” mode, then

resume its “sleep” cycles. This feature significantly reduces quiescent battery drain, and

you may change the amount of “sleep” time between activity checks using the Menu

System:

1. Press the [MON/F] key, then press the [0(SET)] key to enter the Set mode.

2. Rotate the DIAL to select Menu Item (Save Modes #2: RX SAVE).

3. Press the [MAIN] or [SUB] key to select the desired “sleep” duration. The selections

available are 200 ms, 300 ms, 500 ms, 1 second, and 2 seconds, or OFF. The default

value is 200 ms.

4. When you have made your selection, press the PTT key to save the new setting and

exit to normal operation.

. Say

Say Say

Say

: When you are operating on Packet, switch the Receive Battery Saver OFF, as

the sleep cycle may “Collide” with the beginning of an incoming Packet transmission,

causing your TNC not to receive the full data burst.

TX Battery Saver

TX Battery SaverTX Battery Saver

TX Battery Saver

The VX-7R also includes a useful Transmit Battery Saver, which will automatically

lower the power output level when the last signal received was very strong. For example,

when you are in the immediate vicinity of a repeater station, there generally is no

reason to use the full 5 Watts of power output in order to achieve full-quieting access to

the repeater. With the Transmit Battery Saver, the automatic selection of Low Power

operation conserves battery drain significantly.

To activate the Transmit Battery Saver:

1. Press the [MON/F] key, then press the [0(SET)] key to enter the Set mode.

2. Rotate the DIAL to select Menu Item (Save Modes #3: TX SAVE).

3. Press the [MAIN] or [SUB] key to set this Menu Item to “ON” (this activating the

Transmit Battery Saver).

4. When you have completed your selection, press the PTT key to save the new setting

and exit to normal operation.

FCC ID: K66VX-7R

Operating Manual

Vertex Standard Co., Ltd.

Disabling the

Disabling the Disabling the

Disabling the “

““

“I-Beam

I-BeamI-Beam

I-Beam”

””

”

Further battery conservation may be accomplished by disabling the “I-Beam” while

receiving the signal (BUSY LED). Use the following procedure:

1. Press the [MON/F] key, then press the [0(SET)] key to enter the Set mode.

2. Rotate the DIAL to select Menu Item (Display Setup #1: BUSY LED).

3. Press the [MAIN] or [SUB] key to set this Menu Item to “OFF” (thus disabling the

BUSY lamp).

4. Press the PTT key to save the new setting and exit to normal operation.

Automatic Power-Off (APO) Feature

Automatic Power-Off (APO) FeatureAutomatic Power-Off (APO) Feature

Automatic Power-Off (APO) Feature

The APO feature helps conserve battery life by automatically turning the radio off

after a user-defined period of time within which there has been no dial or key activity.

The available selections for the time before power-off are 0.5/1/3/5/8 hours, as well as

APO Off. The default condition for the APO is OFF , and here is the procedure for

activating it:

1. Press the [MON/F] key, then press the [0(SET)] key to enter the Set mode.

2. Rotate the DIAL to select Menu Item (Save Modes #1: APO).

3. Press the [MAIN] or [SUB] key to select the desired time period after which the

radio will automatically shut down.

4. Once you have made your selection, press the PTT key to save the new setting and

exit to normal operation.

Transmitter

Transmitter Transmitter

Transmitter Time-Out Timer (TOT)

Time-Out Timer (TOT)Time-Out Timer (TOT)

Time-Out Timer (TOT)

The TOT feature provides a safety switch which limits transmission to a pre-

programmed value. This will promote battery conservation by not allowing you to make

excessively-long transmissions, and in the event of a stuck PTT switch (perhaps if the

radio or a Speaker/Mic is wedged between car seats) it can prevent interference to other

users as well as battery depletion. As configured at the factory the TOT feature is set to

OFF, and here is the procedure for activating it:

1. Press the [MON/F] key, then press the [0(SET)] key to enter the Set mode.

2. Rotate the DIAL to select Menu Item (Save Modes #4: TOT).

3. Press the [MAIN] or [SUB] key to set the Time-Out Timer to the desired “Maximum

TX” time (1 minute, 2.5 minutes, 5 minutes, or 10 minutes).

4. Once you’re made the selection you wish to use, press the PTT key to save the new

setting and exit to normal operation.

. Say

Say Say

Say

: Since brief transmissions are the mark of a good operator, try setting up your

FCC ID: K66VX-7R

Operating Manual

Vertex Standard Co., Ltd.

radio’s TOT feature for a maximum transmission time of 1 minute. This will

significantly improve battery life, too!

Busy Channel Lock-Out (BCLO)

Busy Channel Lock-Out (BCLO)Busy Channel Lock-Out (BCLO)

Busy Channel Lock-Out (BCLO)

The BCLO feature prevents the radio’s transmitter from being activated if a signal

strong enough to break through the “noise” squelch is present. On a frequency where

stations using different CTCSS or DCS codes may be active, BCLO prevents you from

disrupting their communications accidentally (because your radio may be muted by its

own Tone Decoder). The default setting for the BCLO is OFF, and here is how to change

that setting:

1. Press the [MON/F] key, then press the [0(SET)] key to enter the Set mode.

2. Rotate the DIAL to select Menu Item (Misc Setup #1: BCLO).

3. Press the [MAIN] or [SUB] key to set this Menu Item to “ON” (this activating the

BCLO feature).

4. Press the PTT key to save the new setting and resume normal operation.

MIC Monitor

MIC MonitorMIC Monitor

MIC Monitor

The MIC Monitor feature enable to monitor the sound around the transceiver by the

optional VC-27

Earpiece/Microphone.

1. Connect the VC-27

Earpiece/Microphone to the MIC/EAR jack.

2. Press the [MON/F] key, then press the [0(SET)] key to enter the Set mode.

3. Rotate the DIAL to select Menu Item (Misc Setup #19: MIC MONITOR).

4. Press the [MAIN] or [SUB] key to set this Menu Item to “ON” (this activating the

MIC Monitor feature).

5. Press the PTT key to save the new setting, and the VX-7R’s internal microphone

pick up the sound around the transceiver, then output its to the VC-27

Earpiece/Microphone.

R.F.Say

R.F.SayR.F.Say

R.F.Say

: When this feature is activated without the VC-27

Earpiece/Microphone, the

VX-7R engage the howling.

Changing the TX Deviation Level

Changing the TX Deviation LevelChanging the TX Deviation Level

Changing the TX Deviation Level

In many areas of the world, channel congestion has required that operating channels

be closely spaced. In such operating environments, it often is required that operators

use reduced deviation levels, so as to reduce the potential for interference to users on

adjacent channels. The VX-7R includes a simple method of accomplishing this:

1. Press the [MON/F] key, then press the [0(SET)] key to enter the Set mode.

FCC ID: K66VX-7R

Operating Manual

Vertex Standard Co., Ltd.

2. Rotate the DIAL to select Menu Item (Misc Setup #6: HALF DEV).

3. Press the [MAIN] or [SUB] key to change this setting to ON. In this configuration

(HALF DEVIATION active), the transmitter’s deviation will be approximately ±2.5

kHz.

4. When you have made your selection, press the PTT key to save the new setting and

exit to normal operation.

. Say

Say Say

Say

: The “normal” setting for the deviation (when this Menu item is set to OFF) is

±5 kHz.

Memory Mode

Memory ModeMemory Mode

Memory Mode

The VX-7R provides a wide variety of memory system resources. These include:

# Regular Memory Channel, which made up of;

$ ??? “Standard” memory channels, numbered “1” through “???” (includes ???

channels which already stored Shot-wave Broadcast Station frequency).

$ 12 (USA version) or 11 (EXP version) Home channels, storage and quick

recall of one prime frequency on each operating band.

$ 20 sets of band-edge memories also known as “Programming Memory Scan”

channels, labeled “L1/U1” through “L20/U20”.

$ Ten Memory Groups, labeled “MG0” through “MG9”. Each Memory Group

can be assigned 64 channels from the “standard” memory channel bank.

# Ten One-Touch Memory Channel

# Ten Hyper Memory Channel

Regular

RegularRegular

Regular Memory Channel Operation

Memory Channel Operation Memory Channel Operation

Memory Channel Operation

Memory Storage

1. Select the desired frequency, while operating in the VFO mode. Be sure to set up

any desired CTCSS or DCS tones, as well as any desired repeater offset. The power

level may also be set at this time, if you wish to store it.

2. Press and hold the [MON/F] key for 2 seconds.

3. Within five seconds of releasing the [MON/F] key, rotate the DIAL to select the

desired memory channel. The microprocessor will automatically select the next-

available “free” channel (a memory register on which no data has been stored). If

you see an Asterisk (*) by any channel number, it means that the channel currently

has no data written on it (i.e. the channel is “free”.)

4. Press the [MON/F] key once more to store the frequency into memory.

FCC ID: K66VX-7R

Operating Manual

Vertex Standard Co., Ltd.

5. You still will be operating in the “VFO” mode, so you may now enter other

frequencies, and store them into additional memory locations, by repeating the

above process.

R.F.Say

R.F.SayR.F.Say

R.F.Say

: You may change the automatic memory channel selection feature to “next

memory channel which is last stored memory channel” by the “next-available “free”

channel” via Menu Item (Basic Setup #12 MW MODE).

Storing Independent Transmit Frequencies (“Odd Splits”)

All memories can store an independent transmit frequency, for operation on

repeaters with non-standard shift. To do this:

1. Store the receive frequency using the method already described under MEMORY

STORAGE (it doesn’t matter if a repeater offset is active).

2. Turn to the desired transmit frequency, then press and hold the [MON/F] key for

one second.

3. With in five seconds of releasing the [MON/F] key, rotate the DIAL to select the

same memory channel number as used in step “1” above.

4. Press and hold the PTT switch while pressing the [MON/F] key once more

momentarily (this does not key the transmitter).

. Say

Say Say

Say

: Whenever you recall a memory which contains independently-stored transmit

and receive frequencies, the “[+][–]” indication will appear in the display.

Memory Recall

1. While operating in the VFO mode, press the [V/M(WRITE MT)] key to enter the

Memory mode.

2. Rotate the DIAL to select the desired channel.

3. To return to the VFO mode, press the [V/M(WRITE MT)] key.

. Say

Say Say

Say

: When the radio already enter the Memory mode, an easy way to recall

memories is to key in the memory channel number, then press [V/M(WRITE MT)] key.

For example, to recall memory channel #14, press [1] " [4] " [V/M(WRITE MT)].

HOME Channel Memory

A special one-touch “HOME” channel is available (one for each of the 12 (USA

version) or 11 (EXP version) available operating bands: see page xx), to allow quick

recall of a favorite operating frequency on each band. Memory storage is simple to

accomplish:

1. Select the desired frequency, while operating in the VFO mode. Be sure to set up

FCC ID: K66VX-7R

Operating Manual

Vertex Standard Co., Ltd.

any desired CTCSS or DCS tones, as well as any desired repeater offset. The power

level may also be set at this time, if you wish to store it.

2. Press and hold the [MON/F] key for 2 seconds.

3. While the memory channel number is blinking, just press the [HM/RV(EMG)] key.

The frequency and other data (if any) will now be stored in the special HOME

channel register.

4. You may repeat this process on the other operating bands.

5. To recall the HOME channel, press the [MON/F] key, then press the

[HM/RV(EMG)] key while operating either in the VFO or MR mode.

. Say

Say Say

Say

: Note that the UHF HOME channel is the one used during “Emergency”

operation. See page ?? for details regarding this feature.

Labeling Memories

You may wish to append an alpha-numeric “Tag” (label) to a memory or memories, to

aid in recollection of the channel’s use (such as a club name, etc.). This is easily

accomplished using the Set mode.

1. Recall the memory channel on which you wish to append a label.

2. Press the [MON/F] key, then press the [0(SET)] key to enter the Set mode.

3. Rotate the DIAL to select Menu Item (Basic Setup #11: NAME SET).

4. Press the [BAND(BND DN)] key momentarily to enable programming of the name

tag.

5. Press the [MAIN]/[SUB] key or keyboard to select the first digit of the desired label.

Example 1: Press the [MAIN] or [SUB] key to select any of ?? available characters

(including letters, numbers, and special symbols).

Example 2: Press the [2(DW)] key repeatedly to toggle among the seven available

characters: A " B " C " a " b " c " 2

6. Rotate the DIAL one click clockwise to move to the next character.

7. Repeat the step 4 and 5 to program the remaining letters, numbers, or symbols of

the desired label. A total of eight characters may be used in the creation of a label.

8. When you have completed the creation of the label, press the PTT key to save the

label and exit.

R.F. Say

R.F. SayR.F. Say

R.F. Say

: During “MR” (Memory Recall) operation, appear the alphanumeric Tag below

the frequency display. The alphanumeric Tag does not appear while activate the dual

watch feature.

FCC ID: K66VX-7R

Operating Manual

Vertex Standard Co., Ltd.

Memory Offset Tuning

Once you have recalled a particular memory channel, you may easily tune off that

channel, as though you were in the “VFO” mode.

1. With the VX-7R in the “MR” (Memory Recall) mode, select the desired memory

channel.

2. Now press and hold the [V/M(WRITE MT)] key for 2 seconds. The “MR” indicator

will be replaced by one which says “MT” (“Memory Tuning).

3. Rotate the DIAL, as desired, to tune to a new frequency. The synthesizer steps

selected for VFO operation on the current band will be the steps used during

Memory Tuning.

4. If you wish to return to the original memory frequency, press and hold the

[V/M(WRITE MT)] key for 2 seconds. The “MT” indicator will be replaced by “MR”.

5. If you wish to store a new frequency set during Memory Tuning, just press and hold

in the [MON/F] key for 2 seconds, per normal memory storage procedure. The

microprocessor will automatically set itself to the next-available clear memory

location, and you then press [MON/F] again to lock in the new frequency.

. Say

Say Say

Say

: If you want to replace the original memory contents with those of the new

frequency, be sure to rotate the DIAL to the original memory channel number!

Any required CTCSS/DCS changes, or repeater offset modifications, must be done

before storing the data into the new (or original) memory channel location.

Masking Memories

There may be situations where you want to “Mask” memories so they are not visible

during memory selection or scanning. For example, several memories used only in a city

you visit infrequently may be stored, then “Masked” until you visit that city, at which

time you can “Unmask” them for normal use.

1. Press the [V/M(WRITE MT)] key, if needed, to enter the MR mode.

2. Press and hold in the [MON/F] key for 2 seconds, then rotate the DIAL to select the

memory channel to be “Masked” from view.

3. Press the [V/M(WRITE MT)] key. The display will revert to memory channel #1. If

you rotate the DIAL to the location you just “Masked,” you will observe that it is

now invisible.

4. To Unmask the hidden memory, repeat the above procedure: press and hold in the

[MON/F] key for 2 seconds, rotate the DIAL to select the masked memory’s umber,

then press [V/M(WRITE MT)] to restore the memory channel’s data.

. Say

Say Say

Say

: Watch out! You can manually store data over a “Masked” memory, deleting

FCC ID: K66VX-7R

Operating Manual

Vertex Standard Co., Ltd.

previous data, if you’re not careful. Use the “next available memory” technique (look for

the [*] icon) storage technique to avoid over-writing a masked memory.

Memory Group Operation

Memory Group Assignment

1. Recall the memory channel to be assigned to a Memory Group.

2. Press and hold the [MON/F] key for 2 seconds, then press the numbered key ([0] ~

[9]) you want as the Memory Group for this channel.

3. Now memory channel data is copied into the Memory Group.

Memory Group Recall

1. Set the radio to the Memory mode by pressing the [V/M(WRITE MT)] key, if

necessary.

2. Press the [MON/F] key, then press the [9(SPCL)] key to recall the Special Memory

Menu.

3. Press the [MAIN] or [SUB] key to select the “Memory Group” mode.

4. Press the PTT switch to activate the “Memory Group” mode.

5. Rotate the DIAL knob to select the desired Memory Group (“MG0” ~ “MG9”).

6. Press the [V/M(WRITE MT)] key momentarily to lock in the selected Memory

Group.

7. In the Memory Group, you selects the memory channel in the current memory

group only (up to 64 channels).

8. To change the Memory Group to the other Group, press the [V/M(WRITE MT)] key

momentarily then rotate the DIAL knob.

9. To exit the Memory Group, recall the Special Memory Menu (press [MON/F] +

[9(SPCL)]) then select its setting to “OFF.”

Hyper Memory Mode

Hyper Memory ModeHyper Memory Mode

Hyper Memory Mode

This feature enable to store the current status of the radio into the special memory bank

(Hyper Memory).

For example, if you store the Spectrum Operation

Hyper Memory Storage

1. Setup the transceiver desired status, such as the Spectrum Operation, PMS

scanning, etc.

2. Press and hold the numeric key ([0] through [9]) corresponding to the Hyper

FCC ID: K66VX-7R

Operating Manual

Vertex Standard Co., Ltd.

Memory channel you wish to store for 2 seconds.

R.F.Say

R.F.SayR.F.Say

R.F.Say

: In order to prevent accidental storage, the Hyper Memory Storage feature may

be locked via Menu Item (Basic Setup #14 HYP WRITE).

Hyper Memory Recall

1. Press the [MON/F] key, then press the [9(SPCL)] key to recall the Special Memory

Menu.

2. Press the [MAIN] or [SUB] key to select the “Hyper Memory” mode.

3. Press the PTT switch to activate the “Hyper Memory” mode.

4. Press and hold the numeric key ([0] through [9]) for 2 seconds to recall the Hyper

Memory channel.

5. To exit the Hyper Memory mode, recall the Special Memory Menu (press [MON/F] +

[9(SPCL)]), then select its setting to “OFF.”

One-Touch Memory Mode

One-Touch Memory ModeOne-Touch Memory Mode

One-Touch Memory Mode

The One-Touch feature enable to recall up ten favorite frequencies directly via the

numeric ([0] through [9]) key.

One-Touch Memory Storage

1. Select the desired frequency, while operating in the VFO mode. Be sure to set up

any desired CTCSS or DCS tones, as well as any desired repeater offset. The power

level may also be set at this time, if you wish to store it.

2. Press and hold the [MON/F] key for 2 seconds.

3. Within five seconds of releasing the [MON/F] key, rotate the DIAL to select the

desired One-Touch Memory channel which is labeled “OTM0” through “OTM9.”

4. Press the [MON/F] key once more to store the frequency into the One-Touch

Memory.

5. You still will be operating in the “VFO” mode, so you may now enter other

frequencies, and store them into additional One-Touch Memory locations, by

repeating the above process.

One-Touch Memory Recall

1. Press the [MON/F] key, then press the [9(SPCL)] key to recall the Special Memory

Menu.

2. Press the [MAIN] or [SUB] key to select the “One-Touch Memory” mode.

3. Press the PTT switch to activate the “One-Touch Memory” mode.

4. Press the numeric key ([0] through [9]) corresponding to the One-Touch memory

FCC ID: K66VX-7R

Operating Manual

Vertex Standard Co., Ltd.

you wish to recall.

5. To exit the One-Touch Memory mode, recall the Special Memory Menu (press

[MON/F] + [9(SPCL)]), then select its setting to “OFF.”

Scanning

ScanningScanning

Scanning

The VX-7R allows you to scan just the memory channels, the entire operating band,

or a portion of that band. It will halt on signals encountered, so you can talk to the

station(s) on that frequency, if you like.

Scanning operation is basically the same in each of the above modes. Before you

begin, take a moment to select the way in which you would like the scanner to resume

scanning after it halts on a signal.

Setting the Scan Resume Technique

Setting the Scan Resume TechniqueSetting the Scan Resume Technique

Setting the Scan Resume Technique

Three options for the Scan-Resume mode are available:

5 SEC: In this mode, the scanner will halt on a signal it encounters, and will hold

there for 5 seconds. If you do not take action to disable the scanner within

that time period, the scanner will resume even if the stations are still

active.

BUSY: In this mode, the scanner will halt on a signal it encounters. Two seconds

after the carrier has dropped because the other station(s) ceased

transmission, the scanner will resume. In the case of constant-carrier

signals like Weather Station broadcasts, the scanner will likely remain on

this frequency indefinitely.

HOLD: In this mode, the scanner will halt on a signal it encounters. It will not

restart automatically; you must manually re-initiate scanning if you wish

to resume.

To set the Scan-Resume mode

1. Press the [MON/F] key, then press the [0(SET)] key to enter the Set mode.

2. Rotate the DIAL to select Menu Item (Scan Modes #3: RESUME).

3. Press the [MAIN] or [SUB] key to select the desired scan-resume mode.

4. When you have made your selection, press the PTT key to save the new setting and

exit to normal operation.

. Say

Say Say

Say

: The default condition for this Menu Item is “5 SEC.”

FCC ID: K66VX-7R

Operating Manual

Vertex Standard Co., Ltd.

VFO Scanning

VFO ScanningVFO Scanning

VFO Scanning

This mode allows you to scan the entire current operating band.

1. Select the VFO mode by pressing the [V/M(WRITE MT)] key, if necessary.

2. Press the [MON/F] key, then press the [1(SCAN)] key to start scanning.

3. If and when the scanner encounters a signal strong enough to open the squelch, the

scanner will halt temporarily; the decimal point of the frequency display will blink

during this “Pause” condition.

4. The scanner will then resume according to the Scan Resume selected in the

previous section.

5. To cancel scanning, press the PTT or [V/M(WRITE MT)] key.

. Say

Say Say

Say

: When you are start scanning, the VX-7R will be changing frequency in the

upward direction. If you want to change direction of the scan while it is underway,

rotate the DIAL one click in the opposite direction (in this case, one click counter-

clockwise). You’ll see the scanner turn around and change frequency downward!

You may change the scanning operation to which the VFO frequency will jump to the

low band edge of the

next band

next bandnext band

next band

when the VFO frequency reaches the high edge of the

current band (or vice versa). See page xx Menu Item (Misc Setup #10 VFO MODE).

Memory Scanning

Memory ScanningMemory Scanning

Memory Scanning

Memory scanning is similarly easy to initiate:

$ Set the radio to the Memory mode by pressing the [V/M(WRITE MT)] key, if

necessary.

$ Press the [MON/F] key, then press the [1(SCAN)] key to initiate scanning.

$ As with VFO scanning, the scanner will halt on any signal encountered that is

strong enough to open the squelch; it will then resume scanning according to the

Scan-Resume mode set previously.

$ To cancel scanning, press the PTT or [V/M(WRITE MT)] key.

How to Skip (Omit) a Channel During Memory Scan Operation

As mentioned previously, some continuous-carrier stations like a Weather Broadcast

station will seriously impede scanner operation if you are using the “Carrier Drop”

Scan-Resume mode, as the incoming signal will not pause long enough for the

transceiver to resume scanning. Such channels may be “Skipped” during scanning, if

you like:

1. Set the radio to the Memory Mode by pressing the [V/M(WRITE MT)] key, if

necessary.

FCC ID: K66VX-7R

Operating Manual

Vertex Standard Co., Ltd.

2. Rotate the DIAL to select the Memory Channel to be skipped during scanning.

3. Press the [MON/F] key, then press the [0(SET)] key to enter the Set mode.

4. Rotate the DIAL to select Menu Item (Basic Setup #13: SKIP MODE).

5. Press the [MAIN] or [SUB] key so as to select “SKIP.” It is to be ignored during

scanning. The “ONLY” selection is “Preferential Memory Scan,” described next

column.

6. When you have made your selection, press the PTT key to save the settings and exit

to normal operation.

A small “!” icon will appear when recall the “skipped” memory channel.

To re-institute the channel into the scanning loop, select “OFF” in step 5 above (the

“Skipped” channel will, of course, still be accessible via manual channel selection

methods using the DIAL in the MR mode).

Preferential Memory Scan

The VX-7R also allows you to set up a “Preferential Scan List” of channels which you

can “flag” within the memory system. These channels are designated by a “!” icon when

you have selected them, one by one, for the Preferential Scan List. When you initiate

memory scanning on a channel with the “!” icon appended, only those channels bearing

the “!” icon will be scanned. If you initiate scanning on a channel which does not have

the “!” icon appended, you will scan all channels including those with the “!” icon

appended.

1) Here is the procedure for setting up and using the Preferential Scan List:

1. Press the [V/M(WRITE MT)] key momentarily to enter the Memory Recall mode, if

you are not using memories already.

2. Rotate the DIAL to select the channel which you wish to add to the Preferential

Scan List.

3. Press the [MON/F] key, then press the [0(SET)] key to enter the Set mode.

4. Rotate the DIAL to select Menu Item (Basic Setup #13: SKIP MODE).

5. Press the [MAIN] or [SUB] key so as to select “ONLY.”

6. When you have made your selection, press the PTT key to save the settings and exit

to normal operation.

2) To initiate Preferential Memory Scan:

1. Press the [V/M(WRITE MT)] key momentarily to enter the Memory Recall mode, if

you are not using memories already.

FCC ID: K66VX-7R

Operating Manual

Vertex Standard Co., Ltd.

2. Rotate the DIAL to select any channel which has an “!” icon appended to the

channel number.

3. Press the [MON/F] key, then press the [1(SCAN)] key to initiate Preferential

Memory Scanning. Only the channels which have an “!” icon appended to the

channel number will be scanned.

Programmable (Band Limit) Memory Scan (PMS)

Programmable (Band Limit) Memory Scan (PMS)Programmable (Band Limit) Memory Scan (PMS)

Programmable (Band Limit) Memory Scan (PMS)

This feature allows you to set sub-band limits for either scanning or manual VFO

operation. For example, you might with to set up a limit (in North America) of 144.300

MHz to 148.000 MHz so as to prevent encroachment into the SSB/CW “Weak Signal”

portion of the band below 144.300 MHz. Here’s how to do this:

1. Set the radio to the VFO mode by pressing the [V/M(WRITE MT)] key, if necessary.

2. Using the techniques learned earlier, store (per the above example) 144.300 MHz

into Memory Channel #L1 (the “L” designates the Lower sub-band limit).

3. Likewise, store 148.000 MHz into Memory Channel #U1 (the “U” designates the

Upper sub-band limit).

4. Switch to the Memory mode by pressing the [V/M(WRITE MT)] key once, then

rotate the DIAL to select Memory Channel # L1.

5. Press and hold the [V/M(WRITE MT)] key for 2 seconds to start the PMS; the “MR”

label will be replaced by “PMS” in the upper left-hand corner of the display.

6. 20 pairs of Band Limit memories, labeled L1/U1 through L20/U20 are available.

You therefore can set upper and lower operation limits on a number of bands, if you

like.

“

““

“Priority Channel

Priority ChannelPriority Channel

Priority Channel”

””

” Scanning (Dual Watch)

Scanning (Dual Watch) Scanning (Dual Watch)

Scanning (Dual Watch)

The VX-7R’s scanning features include a two-channel scanning capability which

allows you to operate on a VFO or Memory channel, while periodically checking user

defines Memory Channel for activity. If a station is received on Memory Channel which

is strong enough to open the Squelch, the scanner will pause on that station in

accordance with the Scan-Resume mode set via Menu Item (Scan Modes #3: RESUME).

See page xx.

Here is the procedure for activating Priority Channel Dual Watch operation:

1. Recall the memory channel you wish to be the “Priority” operation.

2. Press and hold the [MON/F] key for 2 seconds, then press the [BAND(BND DN)]

key. A “P” icon will appear to the right of the “MR” icon, indicating it is priority

FCC ID: K66VX-7R

Operating Manual

Vertex Standard Co., Ltd.

channel.

3. Now set the VX-7R for operation on another memory channel, or on a VFO

frequency.

4. Press the [MON/F] key, then press the [2(DW)] key. The display will remain on the

VFO or memory channel selected, but every four seconds the VX-7R will check the

Priority Channel for activity.

Automatic Lamp Illumination on Scan Stop

Automatic Lamp Illumination on Scan StopAutomatic Lamp Illumination on Scan Stop

Automatic Lamp Illumination on Scan Stop

The VX-7R will automatically illuminate the LCD Lamp whenever the scanner stops

on a signal; this allows you to see the frequency of the incoming signal better at night.

Note that this will, of course, increase the battery consumption, so be sure to switch it

off during the day (the default condition for this feature is “ON”).

The procedure for disabling the Scan Lamp is:

1. Press the [MON/F] key, then press the [0(SET)] key to enter the Set mode.

2. Rotate the DIAL to select Menu Item (Scan Modes #4: SCAN LAMP).

3. Press the [MAIN] or [SUB] key to set this Menu Item to OFF.

4. When you have made your selection, press the PTT to save the new setting and exit

to normal operation.

Band Edge Beeper

Band Edge BeeperBand Edge Beeper

Band Edge Beeper

The VX-7R will automatically “beep” when a band edge is encountered during

scanning (either in standard VFO scanning or during PMS operation). You may disable

this feature, if it is annoying, without disabling the keypad beeper (the default condition

for this feature is “ON”.

The procedure for disabling the Band-Edge Beeper is:

1. Press the [MON/F] key, then press the [0(SET)] key to enter the Set mode.

2. Rotate the DIAL to select Menu Item (Scan Modes #2: EDGE BEEP).

3. Press the [MAIN] or [SUB] key to set this Menu Item to OFF.

4. When you have made your selection, press the PTT to save the new setting and exit

to normal operation.

Smart Search Operation

Smart Search OperationSmart Search Operation

Smart Search Operation

The Smart Search feature allows you to load frequencies automatically according to

FCC ID: K66VX-7R

Operating Manual

Vertex Standard Co., Ltd.

where activity is encountered by your radio. When Smart Search is engaged, the

transceiver will search above and below your current frequency, storing active

frequencies as it goes (without stopping on them even momentarily); these frequencies

are stored into a special Smart Search memory band, consisting of 31 memories (15

above the current frequency, 15 below the current frequency, plus the current frequency

itself).

Two basic operating modes for Smart Search are available:

SINGLE Sweep: In this mode, the transceiver will sweep the current band once in

each direction starting on the current frequency. All channels

where activity is present will be loaded into the Smart Search

memories; whether or not all 31 memories are filled, the search

will stop after one sweep in each direction.

CONTINUE: In this mode, the transceiver will make one pass in each direction

as with One-Shot searching; if all 31 channels are not filled after

the first sweep, however, the radio will continue sweeping until

they are all filled.

Setting the Smart Search Mode

Setting the Smart Search ModeSetting the Smart Search Mode

Setting the Smart Search Mode

1. Press the [MON/F] key, then press the [0(SET)] key to enter the Set mode.

2. Rotate the DIAL to select Menu Item (Scan Mode #5: SMRT SRCH).

3. Press the [MAIN] or [SUB] key to select the desired Smart Search mode (see

above).

4. When you have made your selection, press the PTT to save the new setting and exit

to normal operation.

Storing Smart Search Memories

Storing Smart Search MemoriesStoring Smart Search Memories

Storing Smart Search Memories

1. Set the radio to the VFO mode in the desired band.

2. Press the [MON/F] key, then press the [5(S.SCH)] key to enter the Smart Search

mode.

3. Press the [V/M(WRITE MT)] key to begin the Smart Search scanning.

4. As active channels are detected, you will observe the number of “loaded” channels

increasing in the regular memory channel window.

5. Depending on the mode you set for Smart Search operation (SINGLE or

CONTINUE), the Smart Search scan will eventually terminate, and the LCD will

revert to Smart Search Memory Channel “C.”

6. To recall Smart Search memories, rotate the DIAL to choose from among the Smart

FCC ID: K66VX-7R

Operating Manual

Vertex Standard Co., Ltd.

Search memories.

7. To return to normal operation, press the [MON/F] key, then press the [5(S.SCH)]

key.

. Say

Say Say

Say

: Smart Search is a great tool when visiting a city for the first time. You don’t

need to spend hours looking up repeater frequencies from a reference guidebook… just

ask your VX-7R where the action is!

Spectrum analyzer Operation

Spectrum analyzer OperationSpectrum analyzer Operation

Spectrum analyzer Operation

The Spectrum Analyzer allows viewing operating activity on channels above or below

the current operating channel in the VFO mode.

The display indicates the relative signal strength on channels immediately adjacent

to the current operating frequency.

Two basic operating modes for Spectrum Analyzer are available:

SINGLE Sweep: In this mode, the transceiver sweeps the current band once.

CONTINUE: In this mode, the transceiver sweeps the current band repeatedly

until the Spectrum Analyzer is turned off.

Setting the Spectrum Analyzer mode

1. Press the [MON/F] key, then press the [0(SET)] key to enter the Set mode.

2. Rotate the DIAL to select Menu Item (Scan Modes 6: SPEC-ANAL1).

3. Rotate the DIAL to select the desired Spectrum Analyzer mode (see above).

4. When you have made your selection, press the PTT to save the new setting and exit

to normal operation.

To activate the Spectrum Analyzer:

1. Set the radio to the VFO mode in the desired band.

2. Press the [MON/F] key, then press the [6(SP-ANA)] key to activate the Spectrum

Analyzer.

3. When the Spectrum Analyzer is activated, press the [MAIN] or [SUB] key to change

the visible bandwidth. Available selections are ±5, ±8, ±14, ±29, and ±60 channels

(default: ±5 channel). The visible bandwidth, however, depends on the selected

channel step size, so match the default channel steps with the amateur band you

are using.

4. To turn the Spectrum Analyzer off and operate on the centered (and displayed)

FCC ID: K66VX-7R

Operating Manual

Vertex Standard Co., Ltd.

channel, simply press [MON/F] key, then press the [6(SP-ANA)] key.

R.F. Say

R.F. SayR.F. Say

R.F. Say

: You may enable the audio output while activate the Spectrum Analyzer via

Menu Item (Scan Modes #7 SPEC-ANAL2). See page xx for detail.

Channel Counter Operation

Channel Counter OperationChannel Counter Operation

Channel Counter Operation

The Channel Counter allows measuring of the frequency of a nearby transmitter,

without knowing that frequency in advance. The frequency can be measured by

bringing the VX-7R close to the transceiver which is transmitting.

The VX-7R performs a high-speed search within a ±50 MHz range from the

frequency displayed on the LCD. When the strongest signal in that range is identified,

the VX-7R displays the frequency of that (strongest) signal, and writes it into the

special “channel counter memory.

Note: This Channel Counter is designed to provide an indication of the operating

frequency of the incoming signal, one that is close enough to allow the user to tune

precisely to the other station’s frequency. This feature is not, however, designed to

provide a precise determination of the other station’s frequency.

1. Set the radio to the VFO mode in the predication frequency for the transmitter to

be measured.

2. Bring the VX-7R into close proximity to the transmitter to be measured.

3. Press the [MON/F] key, then press the [7(CH.CNT)] key to activate the Channel

Counter, then frequency of the nearby station will be displayed. When the channel

counter is active, engage the 50 dB receiver front-end attenuator. Therefore, only

stations in close proximity may have their frequencies measured using this feature.

4. When it isn’t possible to determine the signal’s frequency, the transceiver will

return to stating frequency of the channel counter operation.

5. Press the [V/M] key. The radio will exit from Channel Counter operation.

Setting the Channel Counter Sweep Width

You may change the bandwidth of the Channel Counter. Available selections are ±5,

±10, ±50, and ±100 MHz (default: ±50 MHz).

Here is the procedure for selecting the Channel Counter Bandwidth:

1. Press the [MON/F] key, then press the [0(SET)] key to enter the Set mode.

2. Rotate the DIAL to select Menu Item (Scan Modes #1: CH COUNTER).

3. Press the [MAIN] or [SUB] key to select the desired bandwidth.

FCC ID: K66VX-7R

Operating Manual

Vertex Standard Co., Ltd.

5. When you have made your selection, press the PTT to save the new setting and exit

to normal operation.

Sensor

SensorSensor

Sensor Mode

Mode Mode

Mode

The VX-7R can be displayed various sensor information. Available selections are

“Current Time,” “Battery Voltage,” “Temperature,” and “Audio Wave form.”

And also, when the optional Barometric Pressure unit (SU-1) is installed, the unique

capability of providing readout of the current barometric pressure. This information is

then used for calculation of your current altitude and weathercast.

The Barometric Pressure unit requires calibration of the “offset” parameters, so that

differences in pressure can be used to calculate altitude. This procedure requires that

you have a calculated barometer, and that you know your current altitude. If you are at

sea level, of course, the latter parameter requires no research.

To display the sensor information:

1. Press the [MON/F] key, then press the [0(SET)] key to enter the Set Mode.

2. Rotate the DIAL to select Menu Item (Measurements #1: SENS DISP).

3. Press the [MAIN] or [SUB] key to select sensor mode you wish to be displayed.

TIME: Indicate the current time.

VOLT: Indicate the battery voltage.

TEMP: Indicate the current temperature inside the transceiver’s case.

WAVE: Indicate the relative (RX and TX) audio wave-form.

BARO: Indicate the Barometric Pressure (requires SU-1).

ALTI: Indicate the Altitude (requires SU-1)

WX: Indicate the Weather Forecast (requires SU-1).

OFF: Disable the sensor information.

4. Press the PTT key momentarily to exit to normal operation and display the sensor

information on the display.

To disable the sensor information, repeat the above procedure, pressing [MAIN] or

[SUB] key to select OFF in step 3 above.

Sensor

SensorSensor

Sensor Mode Options

Mode Options Mode Options

Mode Options

Clock Set

The VX-7R has a 24-hour clock with a calendar which from January 1, 2000 and

ending December 31, 2099.

FCC ID: K66VX-7R

Operating Manual

Vertex Standard Co., Ltd.

To set the clock:

1. Press the [MON/F] key, then press the [0(SET)] key to enter the Set mode.

2. Rotate the DIAL knob to select Menu Item (Misc Setup #16: TIME SET).

3. Press the [BAND(BND DN)] key to enable setting of this Menu Item.

4. Press the [MAIN] or [SUB] key to select the “year” setting.

5. Rotate the DIAL one click clockwise, then press the [MAIN] or [SUB] key to select

the “month” setting.

6. Repeat above step as to “day,” “day of the week,” “hour,” and “minute.”

7. When you have made your choice, press the PTT key to save the new setting and

return to normal operation.

Selecting the Wave Form Display

1. Press the [MON/F] key, then press the [0(SET)] key to enter the Set Mode.

2. Rotate the DIAL to select Menu Item (Measurements #2: WAVE MON).

3. Press the [MAIN] or [SUB] key to select the desire wave form (RX Signal, TX

Modulation, or All).

4. Press the PTT key momentarily to save the your new setting and exit to normal

operation.

Selecting the Unit of Temperature Display

1. Press the [MON/F] key, then press the [0(SET)] key to enter the Set Mode.

2. Rotate the DIAL to select Menu Item (Measurements #3: TEMP UNIT).

3. Press the [MAIN] or [SUB] key to select the preferred unit (°C or °F).

4. Press the PTT key momentarily to save the your new setting and exit to normal

operation.

Selecting the Unit of Atmospheric Pressure Meter (Barometer)

1. Press the [MON/F] key, then press the [0(SET)] key to enter the Set Mode.

2. Rotate the DIAL to select Menu Item (Measurements #4: BARO UNIT).

3. Press the [MAIN] or [SUB] key to select the preferred unit (hpa/mb/Hg/inch).

4. Press the PTT key momentarily to save the your new setting and exit to normal

operation.

Correcting the Atmospheric Pressure Meter (Barometer Offset)

1. Press the [MON/F] key, then press the [0(SET)] key to enter the Set Mode.

2. Rotate the DIAL to select Menu Item (Measurements #5: BARO OFST).

FCC ID: K66VX-7R

Operating Manual

Vertex Standard Co., Ltd.

3. Press the [MAIN] or [SUB] key to set the difference (value) between the VX-7R

display and the calibrated barometer display. For example, if the VX-7R display

shows “1024 hpa” and calibrated barometer indicates “1029 hpa” set the Barometer

offset to “+5”.

4. Press the PTT key momentarily to save the your new setting and exit to normal

operation.

Selecting the Unit of Altimeter

1. Press the [MON/F] key, then press the [0(SET)] key to enter the Set Mode.

2. Rotate the DIAL to select Menu Item (Measurements #6: ALTI UNIT).

3. Press the [MAIN] or [SUB] key to select the preferred unit (m/ft).

4. Press the PTT key momentarily to save the your new setting and exit to normal

operation.

Correcting the Altimeter Setting (Altimeter Offset)

1. Press the [MON/F] key, then press the [0(SET)] key to enter the Set Mode.

2. Rotate the DIAL to select Menu Item (Measurements #7: ALTI OFST).

3. Press the [MAIN] or [SUB] key to set the difference (value) between the VX-7R

display and the currently-displayed value and current location’s altitude. For

example, if the VX-7R display indicates “2m” while you actually are at sea level, set

the Altimeter offset to “–2” in this step. You can set the ALTI OFST at any place

(other than sea level) if you know the true altitude at you current location.

4. Press the PTT key momentarily to save the your new setting and exit to normal

operation.

Timer Operation

Timer OperationTimer Operation

Timer Operation

The VX-7R includes the capability to turn itself on/off at preset time. If you use these

features, must be setup the VX-7R’s clock, described previously.

ON Timer

ON TimerON Timer

ON Timer

1. Press the [MON/F] key, then press the [0(SET)] key to enter the Set mode.

2. Rotate the DIAL to select Menu Item (Save Modes #5: ON TIMER).

3. Press the [BAND(BND DN)] key to enable setting of this Menu Item.

4. Press the [MAIN] or [SUB] key to set the “hour” setting you want the radio to

switch on.

FCC ID: K66VX-7R

Operating Manual

Vertex Standard Co., Ltd.

5. Rotate the DIAL one click clockwise, then press the [MAIN] or [SUB] key to set the

“minute” setting you want the radio to switch on.

6. Rotate the DIAL one click clockwise again, then press the [MAIN] or [SUB] key to

set this Menu Item to “ON.”

7. Once you have made your selection, press the PTT key to save the new setting and

exit to normal operation.

OFF

FFFF

Timer

TimerTimer

Timer

1. Press the [MON/F] key, then press the [0(SET)] key to enter the Set mode.

2. Rotate the DIAL to select Menu Item (Save Modes #6: OFF TIMER).

3. Press the [BAND(BND DN)] key to enable setting of this Menu Item.

4. Press the [MAIN] or [SUB] key to set the “hour” setting you want the radio to

switch off.

5. Rotate the DIAL one click clockwise, then press the [MAIN] or [SUB] key to set the

“minute” setting you want the radio to switch off.

6. Rotate the DIAL one click clockwise again, then press the [MAIN] or [SUB] key to

set this Menu Item to “ON.”

7. Once you have made your selection, press the PTT key to save the new setting and

exit to normal operation.

Display Customization

Display CustomizationDisplay Customization

Display Customization

The VX-7R’s display includes several unique customization options which can

expand your enjoyment of your transceiver.

Icon Mode

Icon ModeIcon Mode

Icon Mode

The display’s alphanumeric labels can be replaced by pictorial icons, which may be

easier to remember during operation.

To activate the Icon mode:

1. Press the [MON/F] key, then press the [0(SET)] key to enter the Set mode.

2. Rotate the DIAL to select Menu Item (Misc Setup #12: ICON SET).

3. Press the [MAIN] or [SUB] key to set this Menu Item to ON.

4. When you have made your selection, press the PTT to save the new setting and exit

to normal operation.

5. The display will change to incorporate the default icons, as stored in the

microprocessor's firmware.

FCC ID: K66VX-7R

Operating Manual

Vertex Standard Co., Ltd.

R.F. Say

R.F. SayR.F. Say

R.F. Say

: The icon is replaced by alphanumeric label while dual band operation.

You can, of course, select the display items which you wish to be represented by icons.

Icon Selection

1. Press the [MON/F] key, then press the [0(SET)] key to enter the Set Mode.

2. Rotate the DIAL to select Menu Item (Misc Setup #14: ICON SEL).

3. Press the [BAND(BND DN)] key to enable modification of this Menu Item.

4. Press the [MAIN] or [SUB] key to select the desired band or mode on which you

wish to utilize an Icon.

5. Turn the DIAL one click clockwise, then press the [MAIN] or [SUB] key to select the

desired Icon to be displayed in place of the regular indicator.

6. Press the PTT key momentarily to save the your new setting and exit to normal

operation.

Icon Editor

The VX-7R has four Icon memory channels which possible the user.

1. Press the [MON/F] key, then press the [0(SET)] key to enter the Set Mode.

2. Rotate the DIAL to select Menu Item (Misc Setup #13: ICON EDIT).

3. Press the [BAND(BND DN)] key to enable this Menu Item.

4. Press the [MAIN] or [SUB] key to select the desired Icon memory channel (1 - 4).

5. A blinking dot appear the upper left corner of the icon field.

6. Pressing the [2(DW)], [8(TONE)], [4(ARTS)], and [6(SP-ANA)] key to move the dot

to “upward,” “downward,” “leftward,” and “rightward” respectively. Bring the dot to

desired point on the icon field, then press the [5(S.SCH)] key to set. (press the

[5(S.SCH)] key )

7. Turn the DIAL one click clockwise, then press the [MAIN] or [SUB] key to select the

desired Icon to be displayed in place of the regular indicator.

8. Press the PTT key momentarily to save the your new setting and exit to normal

operation.

Power-Off Display Mode

Power-Off Display ModePower-Off Display Mode

Power-Off Display Mode

When the VX-7R is turned off, the LCD may be set up to display one or more

environmental measurements. These include temperature, barometric pressure,

altitude, or combinations of these.

1. Press the [MON/F] key, then press the [0(SET)] key to enter the Set mode.

2. Rotate the DIAL to select Menu Item (Display Setup #4: DISP MODE).

FCC ID: K66VX-7R

Operating Manual

Vertex Standard Co., Ltd.

3. Press the [MAIN] or [SUB] key to select the new setting. The options include

NONE: No display when the transceiver is off.

TEMP: Display of temperature when the transceiver is off.

BARO: Display of barometric pressure when the transceiver is off. (requires

optional SU-1)

ALTI: Display of the current altitude when the transceiver is off. (requires

optional SU-1)

TEMP+BARO: Display of Temperature plus barometric pressure.

TEMP+ALTI: Display of Temperature plus altitude.

ALL:

4. When you have made your selection, press the PTT key to save the new setting and

exit to normal operation.

S-and TX Power

S-and TX Power S-and TX Power

S-and TX Power Meter

MeterMeter

Meter

The VX-7R has five types S- and TX Power Meter. You may change to desired type by

default meter.

1. Press the [MON/F] key, then press the [0(SET)] key to enter the Set mode.

2. Rotate the DIAL to select Menu Item (Display Setup #8: MTR SYMB).

3. Press the [MAIN] or [SUB] key to select the desired meter type.

4. When you have made your selection, press the PTT key to save the new setting and

exit to normal operation.

Modification the S-and TX Power Meter Symbol

The default “>” symbol which is used for last meter type may be replaced by several

other symbols, if desired.

Here’s how to replace the meter symbol:

1. Recall the last meter type, described previously.

2.2.

2. Press the [BAND(BND DN)] key to enable modification of this Menu Item.

3. Rotate the DIAL one click clockwise, then press the [MAIN]/[SUB] key or keypad to

select the character in the first digit.

Example 1: Press the [MAIN] or [SUB] key to select any of ?? available characters

(including letters, numbers, and special symbols).

Example 2: Press the [2(DW)] key repeatedly to toggle among the seven available

characters: A " B " C " a " b " c " 2

4. Rotate the DIAL to move to the next digit.

FCC ID: K66VX-7R

Operating Manual

Vertex Standard Co., Ltd.

5. Repeat previous steps 3 and 4 as necessary to complete (up to 8 characters).

6. When you have made your choice, press the [BAND(BND DN)] key, then press the

PTT key to save your selection and exit to normal operation.

R.F. Say

R.F. SayR.F. Say

R.F. Say

: you can make the original font, describe next column.

Font Editor

The VX-7R has two Font memory channels which possible the user.

1. Press the [MON/F] key, then press the [0(SET)] key to enter the Set Mode.

2. Rotate the DIAL to select Menu Item (Misc Setup #11: FONT EDIT).

3. Press the [BAND(BND DN)] key to enable this Menu Item.

4. Press the [MAIN] or [SUB] key to select the desired Font memory channel (1 or 2).

5. A blinking dot appear the upper left corner of the font field.

6. Pressing the [2(DW)], [8(TONE)], [4(ARTS)], and [6(SP-ANA)] key to move the dot

to “upward,” “downward,” “leftward,” and “rightward” respectively. Bring the dot to

desired point on the icon field, then press the [5(S.SCH)] key to set. (press the

[5(S.SCH)] key )

7. Turn the DIAL one click clockwise, then press the [MAIN] or [SUB] key to select the

desired font to be displayed in place of the regular indicator.

8. Press the PTT key momentarily to save the your new setting and exit to normal

operation.

R.F. Say

R.F. SayR.F. Say

R.F. Say

: The original fonts also can be used for the alpha-numeric tag.

Display Contrast

Display ContrastDisplay Contrast

Display Contrast

The LCD’s contrast may be adjusted using the Menu, as well.

1. Press the [MON/F] key, then press the [0(SET)] key to enter the Set mode.

2. Rotate the DIAL to select Menu Item (Display Setup #2: CONTRAST).

3. Press the [MAIN] or [SUB] key to adjust the contrast. As you make the adjustment,

you will be able to see the effects of your changes.

4. When you have completed the adjustment, press the PTT key to save the new

setting and exit to normal operation.

Display

Display Display

Display Dimmer

DimmerDimmer

Dimmer

The LCD and keypad illumination may be adjusted using the Menu, as well.

1. Press the [MON/F] key, then press the [0(SET)] key to enter the Set mode.

2. Rotate the DIAL to select Menu Item (Display Setup #3: DIMMER).

3. Press the [MAIN] or [SUB] key to adjust the comfortable brightness level. As you

FCC ID: K66VX-7R

Operating Manual

Vertex Standard Co., Ltd.

make the adjustment, you will be able to see the effects of your changes.

4. When you have completed the adjustment, press the PTT key to save the new

setting and exit to normal operation.

I-Beam Customization

I-Beam CustomizationI-Beam Customization

I-Beam Customization

The VX-7R’s I-Beam also includes customization options.

COLOR Selection

COLOR SelectionCOLOR Selection

COLOR Selection

1. Press the [MON/F] key, then press the [0(SET)] key to enter the Set Mode.

2. Rotate the DIAL to select Menu Item (Display Setup #7: LED COLOR2).

3. Press the [BAND(BND DN)] key to enable modification of this Menu Item.

4. Press the [MAIN] or [SUB] key to select the desired band or status which you wish

to utilize. Available selections are:

U BAND TX: Set the I-Beam color while transmit on the “Main” band.

L BAND TX: Set the I-Beam color while transmit on the “Sub” band.

U BAND BUSY: Set the I-Beam color while squelch off on the “Main” band.

L BAND BUSY: Set the I-Beam color while squelch off on the “Sub” band.

MR BUSY: Set the I-Beam color while squelch off on the Memory channel.

5. Turn the DIAL one click clockwise, then press the [MAIN] or [SUB] key to select the

desired color to be illuminated in place of the regular color.

6. Press the PTT key momentarily to save the your new setting and exit to normal

operation.

COLOR Editor

COLOR EditorCOLOR Editor

COLOR Editor

1. Press the [MON/F] key, then press the [0(SET)] key to enter the Set Mode.

2. Rotate the DIAL to select Menu Item (Display Setup #6: LED COLOR1).

3. Press the [BAND(BND DN)] key to enable modification of this Menu Item.

4. Press the [MAIN] or [SUB] key to select the desired color which you wish to edit.

5. Turn the DIAL one click clockwise, then press the [MAIN] or [SUB] key to adjust

the “R” (red) element of the color, you will be able to see the effects of your changes.

6. Repeat above step regarding the “G” (Green) and “B” (Blue) elements of the color.

7. Press the [BAND(BND DN)] key to save the your setting, then press the PTT key to

exit to normal operation.

FCC ID: K66VX-7R

Operating Manual

Vertex Standard Co., Ltd.

Reset

ResetReset

Reset

Microprocessor Resetting

Microprocessor ResettingMicroprocessor Resetting

Microprocessor Resetting

To clear all memories and other settings to factory defaults

1. Turn the radio off.

2. Press and hold the [4(ARTS)], [BAND(BND DN)], and [V/M(WRITE MT)] key

while turning the radio on.

3. Press the [MON/F] key momentarily to reset all settings to their factory defaults

(press the another key to cancel the Reset procedure).

Set Mode Resetting

Set Mode ResettingSet Mode Resetting

Set Mode Resetting

To reset the Set (Menu) mode setting to their factory defaults

1. Turn the radio off.

2. Press and hold the [BAND(BND DN)] and [V/M(WRITE MT)] key while turning the

radio on.

3. Press the [MON/F] key momentarily to reset the Set (Menu) mode setting to their

factory defaults (press the another key to cancel the Reset procedure).

Cloning

CloningCloning

Cloning

The VX-7R includes a convenient “Clone” feature, which allows the memory and

configuration data from one transceiver to be transferred to another VX-7R. This can be

particularly useful when configuring a number of transceivers for a public service

operation. Here is the procedure for Cloning one radio’s data to another:

1. Turn both radios off.

2. Connect the optional CT-27 cloning cable between the MIC/EAR jacks of the two

radios.

3. Press and hold the [MON/F] key while turning the radios on. Do this for both radios

(the order of switch on does not matter). “CLONE” will appear on the displays

appear on both radios when the Clone mode is successfully activated in this step.

4. On the Destination radio, press the [V/MR(WRITE MT)] key (“CLONE WAIT” will

appear on the LCD).

5. Press the [BAND(BND DN)] key on the Source radio; “CLONE TX” will appear on

the Source radio, and the data is transferred.

6. If there is a problem during the cloning process, “CLONE ERROR” will be

displayed. Check your cable connections and battery voltage, and try again.

7. If the data transfer is successful, “CLONE” will reappear on both displays. Turn

FCC ID: K66VX-7R

Operating Manual

Vertex Standard Co., Ltd.

both radios off and disconnect the CT-27. You can then turn the radios back on, and

begin normal operation.

Set Mode

Set ModeSet Mode

Set Mode

The VX-7R Set (Menu) mode is easy to activate and set. Use the following procedure:

1. Press the [MON/F] key, then press the [0(SET)] key to enter the Set mode.

2. Turn the DIAL to select the Menu Item to be adjusted.

3. Press the [MAIN]/[SUB] key to adjust or select the parameter to be changed on the

Menu item selected in above step.

4. After completing your selection and adjustment, press the PTT switch momentarily

to exit the Set mode and exit to normal operation.

RF Say: Some Menu Items must be pressing the [BAND(BND DN)] key to enabling

adjustment or select the parameter.

Set Mode Summary

Set Mode Details

Set Mode DetailsSet Mode Details

Set Mode Details

Basic Setup #1 [SQL NFM]

Function: Set the Squelch threshold level for the AM and FM-Narrow modes.

Available Values: 0 ~ 15/AUTO

Default: AUTO

Basic Setup #2 [SQL WFM]

Function: Set the Squelch threshold level for the FM-Wide mode.

Available Values: 0 ~ 8/AUTO

Default: AUTO

Basic Setup #3 [VFO STEP]

Function: Setting of the synthesizer steps.

Available Values: 5/9/10/12.5/15/20/25/50/100 kHz

Default: Depends on the transceiver version.

Basic Setup #4 [RX MODE]

Function: Select the Operating mode.

Available Values: AUTO/N-FM/W-FM/AM

FCC ID: K66VX-7R

Operating Manual

Vertex Standard Co., Ltd.

Default: AUTO (Mode automatically changes according to operating frequency)

Basic Setup #5 [ARS]

Function: Enable/disable the Automatic Repeater Shift function.

Available Values: ON/OFF

Default: ON

Basic Setup #6 [SHIFT]

Function: Set the magnitude of the Repeater Shift.

Available Values: 0.00 ~ 99.95 MHz

Default: Depends on the transceiver version.

Basic Setup #7 [RPT SHIFT]

Function: Set the Repeater Shift Direction

Available Values: +RPT/+RPT/SIMP

Default: Depends on the transceiver version.

Basic Setup #8 [MUTE SET]

Function: Enable/Disable the Audio Mute feature while operating on the Dual Band

reception.

Available Values: ON/OFF

Default: Depends on the transceiver version.

Basic Setup #9 [KEY BEEP]

Function: Enable/disable the Keypad beeper.

Available Values: ON/OFF

Default: ON

Basic Setup #10 [LOCK MODE]

Function: Select the Control Locking lockout combination.

Available Values: KEY/DIAL/PTT/KEY&DIAL/KEY&PTT/DIAL&PTT/ALL

Default: KEY

Basic Setup #11 [NAME SET]

Function: Store Alpha-Numeric “Tags” for the Memory channels.

Name Storing:

FCC ID: K66VX-7R

Operating Manual

Vertex Standard Co., Ltd.

1. Recall the memory channel to be named.

2. Recall this Menu, then press the [BAND(BND DN)] key momentarily.

3. Press the [MAIN]/[SUB] key or keypad to select the desired first letter, number, or

symbol.

Example 1: Press the [MAIN] or [SUB] key to select any of ?? available characters

(including letters, numbers, and special symbols).

Example 2: Press the [2(DW)] key repeatedly to toggle among the seven available

characters: A " B " C " a " b " c " 2

4. Rotate the DIAL one click clockwise to save the first letter/number/symbol.

5. Repeat step 3 and 4 as necessary to complete.

6. Press the press the [BAND(BND DN)] key momentarily, then press the PTT key

momentarily to save the your new setting and exit to normal operation.

Basic Setup #12 [MW MODE]

Function: Select the method of the Memory Writhing.

Available Values: LOWER CH/NEXT CH

Default: LOWER CH

LOWER CH: Store to the next-available “free” channel”

NEXT CH: Store to the next memory channel which is last stored memory channel

Basic Setup #13 [SKIP MODE]

Function: Set the scan “flag” to the Memory channel.

Available Values: OFF/SKIP/PRFCL

Default: OFF

SKIP: The scanner is “skipped.”

PRFCL: The scanner is only checked the channels which have this “flag.”

Basic Setup #14 [HYP WRITE]

Function: Enable/disable the Hyper Memory Writing

Available Values: ENABLE/DISABLE

Default: ENABLE

Display Setup #1 [BUSY LED]

Function: Enable/disable the BUSY LED (“I-Beam”) while the Squelch is open.

Available Values: ON/OFF

Default: ON

FCC ID: K66VX-7R

Operating Manual

Vertex Standard Co., Ltd.

Display Setup #2 [CONTRAST]

Function: Setting of the Display contrast level.

Available Values: 1 ~ 10

Default: 5

Display Setup #3 [DIMMER]

Function: Setting of the Display brightness level.

Available Values: 0 ~ 10

Default: 10

Display Setup #4 [DISP MODE]

Function: Select the display while the transceiver’s power is off

Available Values: NONE/TEMP/BRM/ALT/T+B/T+A/ALL/Weather

Default: NONE

NONE: No display when the transceiver is off.

TEMP: The current temperature will be displayed while the transceiver’s power is off.

BRM: The current barometric pressure will be displayed while the transceiver’s power

is off.

ALT: The current altitude will be displayed while the transceiver’s power is off

(calculated from the barometric pressure).

T+B: The current temperature and barometric pressure will be displayed while the

transceiver’s power is off.

T+A: The current temperature and altitude will be displayed while the transceiver’s

power is off.

Weather: The weather forecast will be displayed while the transceiver’s power is off.

R.F. Says

R.F. SaysR.F. Says

R.F. Says

: The barometric pressure, altitude, and Weather information require the

optional SU-1)

Display Setup #5 [LAMP MODE]

Function: Select the LCD/Keypad Lamp mode.

Available Values: KEY /Continue/OFF

Default: KEY

KEY: Illuminates the LCD/Keypad for 5 seconds when any key is pressed.

Continue: Pressing the LAMP key toggles LCD/Keypad lamp On/Off.

OFF: Disable the LCD/Keypad Lamp.

FCC ID: K66VX-7R

Operating Manual

Vertex Standard Co., Ltd.

Display Setup #6 [LED COLOR 1]

Function: Select the “I-Beam” color for each operating status.

Display Setup #7 [LED COLOR 2]

Function: Edit the “I-Beam” color.

Display Setup #8 [MTR SYMB]

Function: Select the S- & TX PO meter Symbol.

Available Values: Five pattern

Default:

DSQ/DCS/DTMF #1 [SQL TYPE]

Function: Select the Tone Encoder and/or Decoder mode.

Available Values: OFF/T/TSQ/DCS

Default: OFF

T: CTCSS Encoder

TSQ: CTCSS Encoder/Decoder

DCS: Digital Coded Squelch Encoder/Decoder

DSQ/DCS/DTMF #2 [TONE SET]

Function: Setting of the CTCSS Tone Frequency

Available Values: 50 standard CTCSS tones

Default: 100.0 Hz

. Say

Say Say

Say

: In this mode, press the [BAND(BND DN)] key to enable the setting, and press

the [BAND(BND DN)] key again to exit from this item.

DSQ/DCS/DTMF #3 [DCS SET]

Function: Setting of the DCS code.

Available Values: 104 standard DCS codes.

Default: 023

. Say

Say Say

Say

: In this mode, press the [BAND(BND DN)] key to enable the setting, and press

the [BAND(BND DN)] key again to exit from this item.

DSQ/DCS/DTMF #4 [DCS COMP]

Function: Enabled/Disabled the “Inverted” DCS code decode.

FCC ID: K66VX-7R

Operating Manual

Vertex Standard Co., Ltd.

Available Values: ENABLE/DISABLE

Default: DISABLE

DSQ/DCS/DTMF #5 [BELL]

Function: Select the CTCSS Bell ringer repetitions.

Available Values: OFF/1/3/5/8/RPT

Default: OFF

DSQ/DCS/DTMF #6 [SPLIT TONE]

Function: Select the CTCSS Bell ringer repetitions.

Available Values:

Default: OFF

DSQ/DCS/DTMF #7 [DTMF DIALER]

Function: Select the CTCSS Bell ringer repetitions.

Available Values: ON/OFF

Default: OFF

DSQ/DCS/DTMF #8 [DTMF SET]

Function: Programming the DTMF Autodialer.

DTMF Autodialer Programming:

1. After selecting Menu Item 30, press the [BAND(SET)AR] key momentarily.

2. Rotate the DIAL to select the autodial memory number you want to store (9

memories are available).

3. Press the [BAND(SET)AR] key momentarily, then key in the phone number you

want to store (maximum: 16 digits).

Press the [MAIN] key to store the “Pause,” then press again the [MAIN] key to

delete the previously storing data after the cursor.

4. If you make a mistake, rotate the DIAL counterclockwise to back the cursor, then

re-enter the correct number.

5. After entering the final digit, press the PTT key momentarily to save the new

setting and exit to normal operation.

Scan Modes #1 [CH COUNTER]

Function: Select the Channel Counter Search Width.

Available Values: ±5 MHz/±10 MHz/± 50 MHz/±100 MHz

FCC ID: K66VX-7R

Operating Manual

Vertex Standard Co., Ltd.

Default: ± 50 MHz

Scan Modes #2 [EDGE BEEP]

Function: Enable/disable the Band-edge beeper while scanning.

Available Values: ON/OFF

Default: ON

When this feature “ON,” a beep will sound when the scanner reaches the band edge

(during VFO Scanning) or when it reaches Memory channel “1” (during Memory

Channel Scanning).

Scan Modes #3 [RESUME]

Function: Select the Scan Resume mode.

Available Values: 5SEC/BUSY/HOLD

Default: 5 SEC

1~10 SEC: The scanner will hold for selected periods (seconds), then resume whether or

not the other station is still transmitting.

BUSY: The scanner will hold until the signal disappears, then will resume when the

carrier drops.

HOLD: The scanner will stop when a signal is received, and will not restart.

Scan Modes #4 [SCAN LAMP]

Function: Enable/disable the Scan lamp while paused.

Available Values: ON/OFF

Default: ON

Scan Modes #5 [SMRT SRCH]

Function: Select the Smart Search Sweep mode.

Available Values: SINGLE/CONTINUE

Default: SINGLE

SINGLE: The transceiver sweeps the current band once in each direction starting on

the current frequency. All channels where activity is present (up to 15 in each direction)

are loaded into the Smart Search memories. Whether or not all 31 memories are filled,

the search stops after one sweep in each direction.

CONTINUE: The transceiver makes a sweep in each direction as with the “SINGLE”

mode, but if all 31 channels are not filled after the first sweep, the radio continues

sweeping until they are all filled.

FCC ID: K66VX-7R

Operating Manual

Vertex Standard Co., Ltd.

Scan Modes #6 [SPEC-ANAL1]

Function: Select the Spectrum Analyzer Sweep mode.

Available Values: SINGLE/CONTINUE

Default: SINGLE

SINGLE: The transceiver sweeps the current band once.

CONTINUE: The transceiver sweeps the current band repeatedly until the Spectrum

Analyzer is turned off

Scan Modes #7 [SPEC-ANAL2]

Function: Enable/disable the Audio output while the Spectrum Analyzer is activated in

the amateur band.

Available Values: ON/OFF

Default: ON

Measurement #1 [SENS DISP]

Function: Select the display of the sensor unit.

Available Values: OFF/WAVE/TEMP/BARO/ALTI/TIME/WX

Default: OFF

Measurement #2 [WAVE MON]

Function: Select the Wave Form to be measured

Available Values: ALL/RX Signal/TX Modulation

Default: ALL

ALL: Indicate the RX Audio wave form and TX Audio modulation wave form.

RX Signal: Indicate the RX Audio wave.

ALL: Indicate the TX Audio modulation wave form.

Measurement #3 [TEMP UNIT]

Function: Select the measurement unit for the Temperature.

Available Values: °C/°F

Default: Depends on the transceiver version

Measurement #4 [BARO UNIT]

Function: Select the measurement unit for the Barometric Pressure.

Available Values: hpa/mb

FCC ID: K66VX-7R

Operating Manual

Vertex Standard Co., Ltd.

Default: Depends on the transceiver version

Measurement #5 [BARO OFST]

Function: Correcting the Barometric Pressure.

Available Values: –500 ~ +500 hpa (mb)

Default: 0 hpa (mb)

Measurement #6 [ALTI UNIT]

Function: Select the measurement unit for the Altimeter.

Available Values: m/ft

Default: Depends on the transceiver version

Measurement #7 [ALTI OFST]

Function: Correcting the Altimeter.

Available Values: –500 ~ +500 m (ft)

Default: 0 m (ft)

Save Modes #1 [APO]

Function: Set the Automatic Power-Off time.

Available Values: OFF/30 min/1 hour/3 hours/5 hours/8 hours

Default: OFF

Save Modes #2 [RX SAVE]

Function: Select the Receive-mode Battery Saver interval (“sleep” ratio).

Available Values: OFF/200mS(1:1)/300mS(1:1.5)/500mS(1:2.5)/1s(1:5)/2s(1:10)

Default: 200mS(1:1)

Save Modes #3 [TX SAVE]

Function: Enable/disable The Transmit Battery Saver.

Available Values: ON/OFF

Default: OFF

Save Modes #4 [TOT]

Function: Set the TOT time.

Available Values: OFF/1 min/2.5 min/5 min/10 min

Default: OFF

FCC ID: K66VX-7R

Operating Manual

Vertex Standard Co., Ltd.

The time-out timer shuts off the transmitter after continuous transmission of the

programmed time.

Save Modes #5 [ON TIMER]

Function: Set the ON Timer time.

Available Values: OFF/00:00 ~ 23:59

Default: OFF

The ON Timer turns on the radio at the programmed time.

Save Modes #6 [OFF TIMER]

Function: Set the OFF Timer time.

Available Values: OFF/00:00 ~ 23:59

Default: OFF

The OFF Timer turns off the radio at the programmed time.

ARTS #1 [ARTS BEEP]

Function: Select the Beep option during ARTS operation.

Available Values: IN RANGE/ALWAYS/OFF

Default: IN RANGE

RANGE: Beeps sound only when the radio first detects that you are within range.

ALL: Beeps sound every time a polling transmission is received from the other station

(every 15 or 25 seconds when in range).

OFF: No alert beeps sound.

ARTS #2 [ARTS ITVL]

Function: Select the Polling Interval during ARTS operation.

Available Values: 15 SEC/25 SEC

Default: 25 SEC

This setting determines how often the other station will be polled during ARTS

operation.

ARTS #3 [CW ID]

Function: Program and activate the CW Identifier (used during ARTS operation).

CW IDer Programming:

1. After selecting Menu Item 31, press the [BAND(SET)AR] key momentarily.

2. Turn the DIAL one click to change the display from OFF to ON (CW IDer ON).

FCC ID: K66VX-7R

Operating Manual

Vertex Standard Co., Ltd.

3. Press the [BAND(SET)AR] key momentarily, then turn the DIAL to select the first

letter/number of your callsign, and press the [BAND(SET)AR] key momentarily to

save the first letter/number.

4. Repeat the previous step as necessary to complete your callsign, pressing the

[BAND(SET)AR] key after each entry.

5. Press the PTT key momentarily to save the new setting and exit to normal

operation.

Misc Setup #1 [BCLO]

Function: Enable/disable the Busy Channel Lock-Out feature.

Available Values: ON/OFF

Default: OFF

Misc Setup #2 [HOME/REV]

Function: Select the function of the [HM/RV(EMG)] key.

Available Values: HOME/REV

Default: Depends on the transceiver version.

HOME: Pressing this key instantly recalls a favorite “Home” channel.

REV: Pressing this key reverses the transmit and receive frequencies during repeater

operation.

Misc Setup #3 [MON/T-CAL]

Function: Select the MONI key (just below the PTT switch) function.

Available Values: MON/T-CAL

Default: Depends on the transceiver version.

MON: Pressing the MONI key causes the noise/tone Squelch to be over-ridden, allowing

you to listen for weak (or non-encoded) signals.

T-CAL: Pressing the MONI key activates a 1750-Hz burst tone, used for repeater access

in many countries.

Misc Setup #4 [MON-F CNG]

Function: Switch the

Available Values: F/MON

Default: MON.

MON: Pressing the MONI key causes the noise/tone Squelch to be over-ridden, allowing

FCC ID: K66VX-7R

Operating Manual

Vertex Standard Co., Ltd.

you to listen for weak (or non-encoded) signals.

T-CAL: Pressing the MONI key activates a 1750-Hz burst tone, used for repeater access

in many countries.

Misc Setup #5 [EMG SET]

Function: Select the

Available Values: BEEP+STROBE/BEEP/STROBE1/STROBE2/STROBE3/BEAM

Default: BEEP+STROBE

Misc Setup #6 [HALF DEV]

Function: Reducing the Deviation level by 50%.

Available Values: ON/OFF

Default: OFF

Misc Setup #7 [VOX]

Function: Select the VOX operation.

Available Values: OFF/HIGH/LOW

Default: OFF

Misc Setup #8 [VOX DLAY]

Function: Select the VOX delay time.

Available Values: 0.5S/1S/2S

Default: 1S

Misc Setup #9 [BAND LINK]

Function: Enable/disable the BAND Link feature.

Available Values: ON/OFF

Default: OFF

When this feature “ON,” the MAIN and SUB bands are “slaved” so that they change

frequency together.

Misc Setup #10 [VFO MODE]

Function: Select or disable the VFO Band edge for the current band.

Available Values: ALL/BAND

Default: BAND

ALL: When the VFO frequency reaches the high edge of the current band, the VFO

FCC ID: K66VX-7R

Operating Manual

Vertex Standard Co., Ltd.

frequency will jump to the low band edge of the

next band

next bandnext band

next band

(or vice versa).

BAND: When the VFO frequency reaches the high band edge of the current band, the

VFO frequency will jump to the low band edge of the

current band

current bandcurrent band

current band

(or vice versa).

Misc Setup #11 [FONT EDIT]

Function: Edit the User font.

Misc Setup #12 [ICON SET]

Function: Enable/disable the Icon display.

Available Values: ALL/BAND

Default: BAND

Misc Setup #13 [ICON EDIT]

Function: Edit the User Icon.

Misc Setup #14 [ICON SEL]

Function: ICON selection.

1. Recall Menu Item 3, then press the [BAND(BND DN)] key momentarily.

2. Turn the DIAL to select the desired band or mode on which you wish to utilize an

Icon, then press the [BAND(BND DN)] key momentarily.

3. Turn the DIAL to select the desired Icon to be displayed in place of the regular

indicator.

4. Press the PTT key momentarily to save the your new setting and exit to normal

operation.

Misc Setup #15 [CLOCK SFT]

Function: Shifting of CPU clock frequency.

Available Values: ON/OFF

Default: OFF

This function is only used to move a spurious response “birdie” should it fall on a desired

frequency.

Misc Setup #16 [TIME SET]

Function: Set the Clock time.

Misc Setup #17 [LANGUAGE]

FCC ID: K66VX-7R

Operating Manual

Vertex Standard Co., Ltd.

Function: Select the language for the Set (Menu) mode selections.

Available Values: ENGLISH/JAPANESE

Default: ENGLISH

Misc Setup #18 [ATT]

Function: Enable/disable the Front-end Attenuator

Available Values: ON/OFF

Default: OFF

Misc Setup #19 [MIC MONITOR]

Function: Enable/disable the Microphone Monitor feature

Available Values: ON/OFF

Default: OFF

Misc Setup #20 [WX ALERT]

Function: Enable/disable the Weather Alert Feature

Available Values: ON/OFF

Default: OFF

Specifications

SpecificationsSpecifications

Specifications

General

GeneralGeneral

General

Frequency Ranges: MAIN Rx: 05-1.8 MHz (BC Band)

1.8-30 MHz (SW Band)

30-59 MHz (50 MHz HAM: USA version)

30-76 MHz (50 MHz HAM: EXP version)

59-108 MHz (FM: USA version)

76-108 MHz (FM: EXP version)

108-137 MHz (Air Band)

137-174 MHz (144 MHz HAM)

174-222 MHz (VHF-TV)

222-225 MHz (220 MHz HAM: USA version)

225-420 MHz (ACT1: Action Band 1:

USA version)

222-420 MHz (ACT1: Action Band 1:

EXP version)

FCC ID: K66VX-7R

Operating Manual

Vertex Standard Co., Ltd.

420-470 MHz (430 MHz HAM)

470-729 MHz (UHF-TV: USA version)

470-800 MHz (UHF-TV: EXP version)

800-999 MHz (ACT2: Action Band 2,

cellular Blocked)

SUB Rx: 50-54 MHz

137-174 MHz

420-470 MHz

Tx: 50-54 MHz (MAIN & SUB)

144-146 MHz or 144-148 MHz (MAIN & SUB)

222-225 MHz ((MAIN, USA version)

430-440 MHz or 430-450 MHz (MAIN & SUB)

Channel Steps: 5/9/10/12.5/15/20/25/50/100 kHz

Emission Type: F2, F3, A3

Frequency Stability: ±5 ppm (–10 °C to +50 °C [+14 °F to +122 °F])

Antenna Impedance: 50-ohm

Supply Voltage: Nominal: 7.4 V DC, Negative Ground

Operating: 10-16 V DC, Negative Ground (EXT DC jack)

Current Consumption: 150 mA (Mono Band Receive)

(Approx.) 200 mA (Dual Band Receive)

55 mA (Mono Band Receive, Standby, Saver Off)

100 mA (Dual Band Receive, Standby, Saver Off)

25 mA (Mono Band Receive, Standby,

Saver On “Save Ratio 1:5”)

50 mA (Dual Band Receive, Standby,

Saver On “Save Ratio 1:5”)

400 µA (Auto Power Off)

1.6/1.3/1.0/0.7 A (50 MHz, Tx HI/L3/L2/L1)

1.7/1.4/1.1/0.8 A (144 MHz, Tx HI/L3/L2/L1)

0.6 A (220 MHz, Tx)

1.8/1.5/1.2/0.9 A (430 MHz, Tx HI/L3/L2/L1)

Operating Temperature: –20 °C to +60 °C (–4 °F to +140 °F)

Case Size (W x H x D): 60 x 90 x 28 mm (2.4 x 3.5 x 1.1 inch) w/o knob & antenna

Weight (Approx.): 250 g (8.8 oz)

FCC ID: K66VX-7R

Operating Manual

Vertex Standard Co., Ltd.

Transmitter

TransmitterTransmitter

Transmitter

RF Power Output: 5/2.5/1.0/0.5 W (50/144/430 MHz, FM)

0.3W (220 MHz, FM)

1.0W (50 MHz, AM)

Modulation Type: FM: Variable Reactance

AM: Early Stage (Low Level)

Maximum Deviation: ±5/±2.5 kHz

Spurious Emission: At least 60 dB below (@ Tx 1W)

Microphone Impedance: 2 k-ohm

Receiver

ReceiverReceiver

Receiver

Circuit Type: N-FM, AM: Double-Conversion Superheterodyne

W-FM: Triple-Conversion Superheterodyne

IF: 1st: 47.25 MHz (N-FM, AM)

45.8 MHz (W-FM)

2nd: 450 kHz (N-FM, AM)

10.7 MHz (W-FM)

3rd: 1 MHz (W-FM)

Sensitivity: MAIN Rx: 3.0 µV for 10 dB S/N (0.5-30 MHz, AM)

0.5 µV for 12 dB SINAD (30-50, N-FM)

0.16 µV for 12 dB SINAD (50-54, N-FM)

Selectivity: 15 kHz/35 kHz (–6dB/–60dB: N-FM, AM)

200 kHz/300 kHz (–6dB/–20dB: W-FM)

AF Output: 200 mW @ 8 ohm for 10 % THD (@ 7.4 V DC)

400 mW @ 8 ohm for 10 % THD (@ 13.8 V DC)

Specifications are subject to change without notice, and are guaranteed within amateur

bands only.

Installation of the SU-1

Installation of the SU-1Installation of the SU-1

Installation of the SU-1

1. Make sure that the transceiver is off. Remove the hard or soft case, if used.

2. Remove the battery pack.

3. Locate the connector for the SU-1 under the caution seal in the battery

compartment on the back of the radio, just peel off the caution seal.

4. Align the connector on the SU-1 with the transceiver’s connector and gently press

FCC ID: K66VX-7R

Operating Manual

Vertex Standard Co., Ltd.

the unit into place.

5. Affix the new (supplied) caution seal, and replace the battery.

6. Installation is now complete.

Important note

The Barometric Pressure/Altitude features of the optional SU-a are designed to be

supplemental aids for the information of the user, and are not intended to be a

substitute for accurate, calibrated Barometer or Altimeter devices used for navigation

critical to personal safety.

Yaesu Musen VX-7R Amateur Scanning Transceiver User Manual Manual

Yaesu Musen Co., Ltd. Amateur Scanning Transceiver Manual

Contents

Manual

Navigation menu

Namespaces

Views

Navigation