Yale 2 7130(F) Series Mortise Exit Devices Installation Instructions 80 9470 0030 00003 137130Mortise

User Manual: Yale 7130(F) Series Mortise Exit Devices Installation Instructions Installation Instructions

Open the PDF directly: View PDF .
Page Count: 6

Download
Open PDF In Browser	View PDF

7130(F) Series Mortise Exit Devices
Installation Instructions

Outside Trim
Device is packed ready for any
Yale 650F or 660F Series Trim.

(3) 8-32 x 5/16" PUFHMS
End Clamp

End Cap
(2) 1/4-20 x 1" PPHMS
Mortise Lock
(See Mortise Lock Chart)

Hole Plug
(Fire Devices)

(2) 12-12-24 FHPWMS
798 Universal Strike

Dogging Key

Device Assembly

(2) 1/4-20 x 3/4" PRHMS
(Special Head)

Armor Front

Cover

Armor Front Screw
(2) 12-12-24 FHPWMS
(2) 8-32 x 5/16" PUFHMS

ABBREVIATION

FASTENER DESCRIPTION

PPHMS

PHILLIPS PAN HEAD MACHINE SCREW

PRHMS

PHILLIPS ROUND HEAD MACHINE SCREW

FHPWMS

FLAT HEAD PHILLIPS WOOD/MACHINE SCREW

PUFHMS

PHILLIPS UNDER CUT FLAT HEAD MACHINE SCREW

Mortise Lock Chart
Function
Exit Only
F02
F03 (Knob)
F03 (Lever)
F05
F06 (Knob)
F08 (Lever)

Lock Number
Panic Label
Fire Label
35K

35KF

35L
38T
38K
38L

35LF
38TF
38KF
38LF

Attention Installer
Any retrofit or other field modification to a fire rated
opening can potentially impact the fire rating of the
opening, and Yale Locks & Hardware makes no
representations or warranties concerning what such
impact may be in any specific situation. When
retrofitting any portion of an existing fire rated
opening, or specifying and installing a new fire-rated
opening, please consult with a code specialist or
local code official (Authority Having Jurisdiction) to
ensure compliance with all applicable codes and
ratings.
All dimensions are in inches (mm) unless otherwise noted.

80-9470-0030-000 (03-13)
An ASSA ABLOY Group brand

To Change Hand

Maintenance

For Metal, Composite and Wood Doors
Handed Mortise Lock

1. Periodically remove covers and coat mechanisms with a silicone
base lubricant. This is particularly required in corrosive
environments for proper product function.

(See "To Change Mortise Lock Hand", below)

2. Check mounting fasteners periodically. Retighten if found loose.
Apply screw locking compound (available at automotive part
stores) or change part fasteners if screws continue to back up.

Device is non handed

Shim Kit Option
List Number: 723W Black Finish

Kit consists of Latch Head Shim
(Device Cover seats on shim) and
End Clamp Shim (End Cap seats
on shim).
RHR Door

Each shim is 1/8 (3.2) thick.
More than two Shim Kits require
longer device mounting screws
(not included).

LHR Door

To Change Mortise Lock Hand
Typical Lock Body with Cover
removed and showing only
components relevant to lock
handing. Other components vary
according to function.

Guardbolt Plate Assembly
(Hold in place while
removing guardbolt)
Spring
(Note position before
removing guardbolt)
Remove latchbolt
assembly in this direction.

Guardbolt
Push In
Note position
of Guard Lever
Latchbolt
Guard Lever

To change lock hand remove,
flip latchbolt and guardbolt
and reinstall.

Nylon Washer (must be between
spring and bracket in case)

Check Before Starting
Unreinforced Doors or Frames

Min. Door Stile
4-1/2" (114mm)
Door and frame must
meet structural and
dimensional specifications
on exit device template(s)
for door and frame
preparation.

Doors and Frames with walls having a structural
thickness (metal skin plus reinforcement or solid
hardwood) to engage less than (3) full screw threads
are considered unreinforced.
Unreinforced Doors: Use SNB (sex nuts and bolts).
Unreinforced Frames: Use Blind Rivet Nuts.
Recommended fasteners for unreinforced openings
are not necessarily supplied by Yale Security, Inc.

Door Must Swing Freely

Reinforcement
Door Skin

Blind Rivet Nut

2
80-9470-0030-000 (03-13)
An ASSA ABLOY Group brand

1. Mark Door
Locate and Mark Horizontal and Vertical Reference
Centerlines as shown.
LHR door shown
preparation is typical
for both door hands.

DOOR, LOCK AND STRIKE

(ANSI A115.1 BACKSET)

Note: Centerline of Lock (cutout)
must match Horizontal Reference
centerline.

Finished Floor

2. Prepare Door & Frame
Factory prepared cutouts with field drilled mounting holes are
recommended. If door (lock) and frame (strike) have to be mortised in
the field, do it before continuing (follow instructions on Installation
Template).

Spot and Prepare Mounting Holes As Follows:
A. Locate and tape Trim Template to door.
(See instructions packed with Trim.)
B. Locate “Device Template” aligning VERTICAL REFERENCE
and HORIZONTAL REFERENCE lines on door and template.
Tape template to door face.
(1) slot 1/2" (12.7) Dia. x 1" (25.4) on centers thru inside door face and
(2) Device holes for 1/4-20 Machine Screws*, or for 3/8" (9.5) Dia. Sex
nuts and Bolts.
(*) Metal reinforced doors only.

Device Template

C. Insert lock into mortise, adjust front for door edge (beveled or flat)*.
(2) Lock holes for 12-24 Machine Screws or for #12 Wood Screws.
(*) NOTE: Lock base front has to be field tightened in place, (two screws,
each on lock case top and bottom).
D. Seat strike in frame cutout.
(2) Strike holes for 12-24 Machine Screws, or for #12 Wood Screws.

3
80-9470-0030-000 (03-13)
An ASSA ABLOY Group brand

3. Size Device

4. Clear Raised Door Molding
Device must seat flush on door surface, or
on shims that keep it parallel to door face.

One Shim Kit #723W required for each 1/8" (3mm) of device lift needed.
Two Shim Kits Maximum for standard device in 1-3/4" (44) door.
For thicker doors, consult the factory.

One Shim Kit #723W
per 1/8" (3mm) of raised
molding.

4
80-9470-0030-000 (03-13)
An ASSA ABLOY Group brand

5. Install Components
A. Install Lock
Lock in hand, depress guardbolt. Check that
latchbolt is deadlocked.
Check that latchbolt lever (and cylinder lever,
hubs, and thumbpiece lever, if relevant) operate
the lock freely.
Insert Lock Body into door cavity. Fasten to door
edge (2 FHPWMS) Note: Make sure that door
reinforcing clips or doorwalls support lock
immovable (restricting rocking motion).
B. Install Armor Front
Fit over bolts and fasten to lock base front (2
PUFHMS). Check that bolts retract and extend
freely.
C. Install Strike
Seat in place (lip bend away from opening).
Fasten to frame (2 FHPWMS).
D. Install Trim
Follow instructions packed with trim.
E. Install Device
Seat Bar in place (Device finger must engage
latchbolt lever, thru slot in lock case/cover, as
shown in Detail 1). Fasten Device Head (2
PRHMS or SNB).
Set Bar level. Locate End Clamp holes.
Prepare end Clamp mounting holes. Fasten End
Clamp in place. (2 #1/4-20 PRHMS or 3/8" (9.5)
dia SNB)
F. Check Operation
1. Depress touchbar (bolt must retract). Release
touchbar (bolt must extend).
2. Actuate trim (bolt must retract). Release trim
actuator (bolt must extend).
3. (NOT FOR FIRE DEVICES). Depress touchbar,
turn dogging key clockwise (bar must remain
depressed, bolt must remain retracted). Turn
dogging key counterclockwise (bar and bolt
must return to extended position).
4. Close door. Latchbolt should fully engage into
strike cavity, guardbolt should retract over strike
ramp. Door should not rattle.
NOTE: When resulting operation if faulty, check first
for visible binding or interference. If there is no
apparent reason for the fault, remove item from
the door and recheck its operation before
assuming that it is defective.

DETAIL 1

G. Tighten all mounting screws.

5
80-9470-0030-000 (03-13)
An ASSA ABLOY Group brand

6. Install Head Cover and End Cap

Use (2) 8-32 PUFHMS for Head Cover
Use (3) 8-32 PUFHMS for End Cap

Product Support Tel 800.438.1951 • www.yalelocks.com
Yale Locks & Hardware is a division of Yale Security Inc., an ASSA ABLOY Group company.
Yale® is a registered trademark of Yale Security Inc., an ASSA ABLOY Group company. Other products' brand names may be trademarks or registered trademarks of their respective owners and
are mentioned for reference purposes only. These materials are protected under U.S. copyright laws. All contents current at time of publication. Yale Security Inc. reserves the right to change
availability of any item in this catalog, its design, construction, and/or its materials. Copyright © 1996, 2013, Yale Security Inc., an ASSA ABLOY Group company. All rights reserved. Reproduction
in whole or in part without the express written permission of Yale Security Inc., an ASSA ABLOY Group company is prohibited.

6
80-9470-0030-000 (03-13)
An ASSA ABLOY Group brand



---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.5
Linearized                      : Yes
Author                          : Owner
Create Date                     : 2013:03:06 22:44:14-05:00
Modify Date                     : 2013:03:07 08:50:43-05:00
XMP Toolkit                     : Adobe XMP Core 5.2-c001 63.139439, 2010/09/27-13:37:26
Format                          : application/pdf
Creator                         : Owner
Title                           : Untitled-2
Creator Tool                    : CorelDRAW X6
Metadata Date                   : 2013:03:07 08:50:43-05:00
Producer                        : Corel PDF Engine Version 16.1.0.843
Document ID                     : uuid:5d31c8d2-9b4f-4666-b207-c24712e4618c
Instance ID                     : uuid:7f62c18d-5878-4505-8ac3-a67b254886af
Page Count                      : 6
Profile CMM Type                : Lino
Profile Version                 : 2.1.0
Profile Class                   : Display Device Profile
Color Space Data                : RGB
Profile Connection Space        : XYZ
Profile Date Time               : 1998:02:09 06:49:00
Profile File Signature          : acsp
Primary Platform                : Microsoft Corporation
CMM Flags                       : Not Embedded, Independent
Device Manufacturer             : IEC
Device Model                    : sRGB
Device Attributes               : Reflective, Glossy, Positive, Color
Rendering Intent                : Perceptual
Connection Space Illuminant     : 0.9642 1 0.82491
Profile Creator                 : HP
Profile ID                      : 0
Profile Copyright               : Copyright (c) 1998 Hewlett-Packard Company
Profile Description             : sRGB IEC61966-2.1
Media White Point               : 0.95045 1 1.08905
Media Black Point               : 0 0 0
Red Matrix Column               : 0.43607 0.22249 0.01392
Green Matrix Column             : 0.38515 0.71687 0.09708
Blue Matrix Column              : 0.14307 0.06061 0.7141
Device Mfg Desc                 : IEC http://www.iec.ch
Device Model Desc               : IEC 61966-2.1 Default RGB colour space - sRGB
Viewing Cond Desc               : Reference Viewing Condition in IEC61966-2.1
Viewing Cond Illuminant         : 19.6445 20.3718 16.8089
Viewing Cond Surround           : 3.92889 4.07439 3.36179
Viewing Cond Illuminant Type    : D50
Luminance                       : 76.03647 80 87.12462
Measurement Observer            : CIE 1931
Measurement Backing             : 0 0 0
Measurement Geometry            : Unknown
Measurement Flare               : 0.999%
Measurement Illuminant          : D65
Technology                      : Cathode Ray Tube Display
Red Tone Reproduction Curve     : (Binary data 2060 bytes, use -b option to extract)
Green Tone Reproduction Curve   : (Binary data 2060 bytes, use -b option to extract)
Blue Tone Reproduction Curve    : (Binary data 2060 bytes, use -b option to extract)

EXIF Metadata provided by EXIF.tools