Yale 2 7130(F) Series Mortise Exit Devices Installation Instructions 80 9470 0030 00003 137130Mortise

User Manual: Yale 7130(F) Series Mortise Exit Devices Installation Instructions Installation Instructions

Open the PDF directly: View PDF .
Page Count: 6

7130(F) Series Mortise Exit Devices

Installation Instructions

All dimensions are in inches (mm) unless otherwise noted.

(2) 1/4-20 x 1" PPHMS

(3) 8-32 x 5/16" PUFHMS

End Clamp

End Cap

Attention Installer

Any retrofit or other field modification to a fire rated

opening can potentially impact the fire rating of the

opening, and Yale Locks & Hardware makes no

representations or warranties concerning what such

impact may be in any specific situation. When

retrofitting any portion of an existing fire rated

opening, or specifying and installing a new fire-rated

opening, please consult with a code specialist or

local code official (Authority Having Jurisdiction) to

ensure compliance with all applicable codes and

ratings.

Cover

Outside Trim

Device is packed ready for any

Yale 650F or 660F Series Trim.

Mortise Lock Chart

Function Lock Number

Panic Label Fire Label

Exit Only

F02

F03 (Knob)

F03 (Lever)

F05

F06 (Knob)

F08 (Lever)

35K

35L

38T

38K

38L

35KF

35LF

38TF

38KF

38LF

Mortise Lock

(See Mortise Lock Chart)

798 Universal Strike

(2) 12-12-24 FHPWMS

Armor Front Screw

Armor Front

Device Assembly

(2) 1/4-20 x 3/4" PRHMS

(Special Head)

(2) 8-32 x 5/16" PUFHMS

Dogging Key

Hole Plug

(Fire Devices)

PPHMS

PRHMS

FHPWMS

PUFHMS

PHILLIPS PAN HEAD MACHINE SCREW

FLAT HEAD PHILLIPS WOOD/MACHINE SCREW

PHILLIPS UNDER CUT FLAT HEAD MACHINE SCREW

PHILLIPS ROUND HEAD MACHINE SCREW

FASTENER DESCRIPTION

ABBREVIATION

(2) 12-12-24 FHPWMS

An ASSA ABLOY Group brand

80-9470-0030-000 (03-13)

2

To Change Hand

Check Before Starting

Unreinforced Doors or Frames

Doors and Frames with walls having a structural

thickness (metal skin plus reinforcement or solid

hardwood) to engage less than (3) full screw threads

are considered unreinforced.

Unreinforced Doors: Use SNB (sex nuts and bolts).

Unreinforced Frames: Use Blind Rivet Nuts.

Recommended fasteners for unreinforced openings

are not necessarily supplied by Yale Security, Inc. Reinforcement

Door Skin Blind Rivet Nut

Door Must Swing Freely

Min. Door Stile

4-1/2" (114mm)

Maintenance

1. Periodically remove covers and coat mechanisms with a silicone

base lubricant. This is particularly required in corrosive

environments for proper product function.

2. Check mounting fasteners periodically. Retighten if found loose.

Apply screw locking compound (available at automotive part

stores) or change part fasteners if screws continue to back up.

Door and frame must

meet structural and

dimensional specifications

on exit device template(s)

for door and frame

preparation.

LHR DoorRHR Door

Shim Kit Option

Kit consists of Latch Head Shim

(Device Cover seats on shim) and

End Clamp Shim (End Cap seats

on shim).

Each shim is 1/8 (3.2) thick.

More than two Shim Kits require

longer device mounting screws

(not included).

List Number: 723W Black Finish

For Metal, Composite and Wood Doors

Handed Mortise Lock

(See "To Change Mortise Lock Hand", below)

Device is non handed

To Change Mortise Lock Hand

Typical Lock Body with Cover

removed and showing only

components relevant to lock

handing. Other components vary

according to function.

Push In

Note position

of Guard Lever

Latchbolt

Guard Lever

To change lock hand remove,

flip latchbolt and guardbolt

and reinstall.

Guardbolt

Guardbolt Plate Assembly

(Hold in place while

removing guardbolt)

Spring

(Note position before

removing guardbolt)

Remove latchbolt

assembly in this direction.

Nylon Washer (must be between

spring and bracket in case)

An ASSA ABLOY Group brand

80-9470-0030-000 (03-13)

An ASSA ABLOY Group brand

80-9470-0030-000 (03-13)

3

2. Prepare Door & Frame

Spot and Prepare Mounting Holes As Follows:

A. Locate and tape Trim Template to door.

(See instructions packed with Trim.)

B. Locate “Device Template” aligning VERTICAL REFERENCE

and HORIZONTAL REFERENCE lines on door and template.

Tape template to door face.

(1) slot 1/2" (12.7) Dia. x 1" (25.4) on centers thru inside door face and

(2) Device holes for 1/4-20 Machine Screws*, or for 3/8" (9.5) Dia. Sex

nuts and Bolts.

(*) Metal reinforced doors only.

C. Insert lock into mortise, adjust front for door edge (beveled or flat)*.

(2) Lock holes for 12-24 Machine Screws or for #12 Wood Screws.

(*) NOTE: Lock base front has to be field tightened in place, (two screws,

each on lock case top and bottom).

D. Seat strike in frame cutout.

(2) Strike holes for 12-24 Machine Screws, or for #12 Wood Screws.

Factory prepared cutouts with field drilled mounting holes are

recommended. If door (lock) and frame (strike) have to be mortised in

the field, do it before continuing (follow instructions on Installation

Template).

Device Template

1. Mark Door

Finished Floor

Locate and Mark Horizontal and Vertical Reference

Centerlines as shown.

LHR door shown

preparation is typical

for both door hands.

Note: Centerline of Lock (cutout)

must match Horizontal Reference

centerline.

DOOR, LOCK AND STRIKE

(ANSI A115.1 BACKSET)

Device must seat flush on door surface, or

on shims that keep it parallel to door face.

4

4. Clear Raised Door Molding

One Shim Kit #723W required for each 1/8" (3mm) of device lift needed.

Two Shim Kits Maximum for standard device in 1-3/4" (44) door.

For thicker doors, consult the factory.

One Shim Kit #723W

per 1/8" (3mm) of raised

molding.

3. Size Device

An ASSA ABLOY Group brand

80-9470-0030-000 (03-13)

A. Install Lock

Lock in hand, depress guardbolt. Check that

latchbolt is deadlocked.

Check that latchbolt lever (and cylinder lever,

hubs, and thumbpiece lever, if relevant) operate

the lock freely.

Insert Lock Body into door cavity. Fasten to door

edge (2 FHPWMS) Note: Make sure that door

reinforcing clips or doorwalls support lock

immovable (restricting rocking motion).

B. Install Armor Front

Fit over bolts and fasten to lock base front (2

PUFHMS). Check that bolts retract and extend

freely.

C. Install Strike

Seat in place (lip bend away from opening).

Fasten to frame (2 FHPWMS).

D. Install Trim

Follow instructions packed with trim.

E. Install Device

Seat Bar in place (Device finger must engage

latchbolt lever, thru slot in lock case/cover, as

shown in Detail 1). Fasten Device Head (2

PRHMS or SNB).

Set Bar level. Locate End Clamp holes.

Prepare end Clamp mounting holes. Fasten End

Clamp in place. (2 #1/4-20 PRHMS or 3/8" (9.5)

dia SNB)

5. Install Components

5

F. Check Operation

1. Depress touchbar (bolt must retract). Release

touchbar (bolt must extend).

2. Actuate trim (bolt must retract). Release trim

actuator (bolt must extend).

3. (NOT FOR FIRE DEVICES). Depress touchbar,

turn dogging key clockwise (bar must remain

depressed, bolt must remain retracted). Turn

dogging key counterclockwise (bar and bolt

must return to extended position).

4. Close door. Latchbolt should fully engage into

strike cavity, guardbolt should retract over strike

ramp. Door should not rattle.

NOTE: When resulting operation if faulty, check first

for visible binding or interference. If there is no

apparent reason for the fault, remove item from

the door and recheck its operation before

assuming that it is defective.

G. Tighten all mounting screws.

DETAIL 1

An ASSA ABLOY Group brand

80-9470-0030-000 (03-13)

An ASSA ABLOY Group brand

80-9470-0030-000 (03-13)

6. Install Head Cover and End Cap

6

Product Support Tel 800.438.1951 • www.yalelocks.com

Yale® is a registered trademark of Yale Security Inc., an ASSA ABLOY Group company. Other products' brand names may be trademarks or registered trademarks of their respective owners and

are mentioned for reference purposes only. These materials are protected under U.S. copyright laws. All contents current at time of publication. Yale Security Inc. reserves the right to change

availability of any item in this catalog, its design, construction, and/or its materials. Copyright © 1996, 2013, Yale Security Inc., an ASSA ABLOY Group company. All rights reserved. Reproduction

in whole or in part without the express written permission of Yale Security Inc., an ASSA ABLOY Group company is prohibited.

Yale Locks & Hardware is a division of Yale Security Inc., an ASSA ABLOY Group company.

Use (3) 8-32 PUFHMS for End Cap

Use (2) 8-32 PUFHMS for Head Cover