Yamaha CRX N560 Firmware Update Procedure_EN_rev1 / N560D MCR Procedure EN Rev1

User Manual: Yamaha CRX-N560 / CRX-N560D / MCR-N560 / MCR-N560D Firmware Update Procedure

Open the PDF directly: View PDF PDF.
Page Count: 4

Firmware Update Procedure for
CRX-N560/N560D (MCR-N560/MCR-N560D)
IMPORTANT NOTICE
Follow the instructions carefully and do not attempt any other procedures not specified in the
instructions provided by Yamaha.
Improperly updated products may cause improper operation, and any parts or service required to
restore proper operation will not be covered under the Yamaha Limited Warranty.
Choose from the following 2 methods to update to the latest firmware.
Click here for Firmware Update Through the Internet
(Connection to the Internet is required)
Click here for Firmware Update by USB
(A USB thumb drive is required)
In case of error, see the Troubleshooting section
[ 1. Firmware Update Through the Internet ]
Requirements:
Your network CD receiver is connected to the Internet if you can receive
Internet radio stations. (See owner’s manual for details)
STEP 1 Power on the unit and enter option settings
Press OPTION button on the remote control.
STEP 2 Start Update
Using the UP/DOWN buttons, select menu “System Config”
and press ENTER button. After that, select “Firm Update” using
UP/DOWN buttons and press Enter button.
Initially, “Network” is flashing on the display.
To perform network update, select “Network” and press Enter button.
(Update in progress…)
ENTER
UP
DOWN
OPTION
Firmware Update Procedure for
CRX-N560/N560D (MCR-N560/MCR-N560D)
note:
DO NOT
interrupt the power or press any buttons during the update.
In case the power is accidentally cut off, the network player will restore original
firmware. Perform the update procedure from STEP 1 again.
Update is completed when “
Update success.
”, “
Please…
”, “
power off!
” is
displayed alternately. Then, power off the unit.
STEP 3 Confirm updated firmware version
Power on and press the
OPTION
button on the remote control and select
“
System Config
” using the
UP/DOWN
buttons. Press
ENTER
and select “
Firm
Version
” accordingly. Press
ENTER
again to confirm that the firmware version has
been updated.
(X
(XX.XX shows actual firmware version.)
Congratulations!
You have completed the firmware update. Your player is ready for normal use.
[ 2. Firmware Update by USB ]
Requirements:
・
USB thumb drive, with enough free space to store the firmware.
（
File system with FAT16 or FAT32 format
）
・
Firmware file provided by Yamaha.
STEP 1 Insert the USB thumb drive on the front panel.
STEP 2 Power on the unit and enter option settings
Press
OPTION
button on the remote control.
STEP 3 Start Update
Using the
UP/DOWN
buttons, select menu “
System Config
”
and press
ENTER
button. After that, select “
Firm Update
” using
UP/DOWN
buttons and press
Enter
button.
ENTER
OPTION
UP
DOWN
XXX.XX
Firmware Update Procedure for
CRX-N560/N560D (MCR-N560/MCR-N560D)
Initially, “Network” is flashing on the display. To perform USB update,
select “USB” using UP/DOWN buttons and press Enter button.
(Update in progress…)
note:
DO NOT interrupt the power or press any buttons during the update.
In case the power is accidentally cut off, the network player will restore original
firmware. Perform the update procedure from STEP 1 again.
Update is completed when “
Update success.
”, “
Please…
”, “
power off!
” is
displayed alternately. Then, power off the unit.
STEP 4 Confirm updated firmware version
Power on and press the OPTION button on the remote control and select
“
System Config
” using the UP/DOWN buttons. Press ENTER and select “Firm
Version” accordingly. Press ENTER again to confirm that the firmware version has
been updated.
(X
(XX.XX shows actual firmware version.)
Congratulations!
You have completed the firmware update. Your player is ready for normal use.
XXX.XX
Firmware Update Procedure for
CRX-N560/N560D (MCR-N560/MCR-N560D)
[ 3. Troubleshooting ]
In case error message appeared during the update and unable to power on, perform
following update procedure.
STEP 1 Copy the update file to a USB thumb drive
Unzip the downloaded file and copy to the root directory of a USB thumb drive.
Be sure to delete all other files in a USB thumb.
STEP 2 Insert the USB thumb drive on the front panel
In this step, AC power cable needs to be disconnected. The disconnection needs to
be kept for several minutes.
STEP 3 Enter firmware update mode
Connect AC power cable to AC outlet, while pressing button.
”
USB UPDATE
” will be shown in the front panel display.
Firmware update will be started automatically.
note:
DO NOT interrupt the power or press any buttons during the update.
In case the power is accidentally cut off, perform the update procedure from STEP 1
again.
Update is completed when “
Update success.
”, “
Please…
”, “
power off!
” is
displayed alternately. Then, power off the unit.
STEP 4 Confirm updated firmware version
Power on and press the OPTION button on the remote control and select
“
System Config
” using the UP/DOWN buttons. Press ENTER and select “Firm
Version” accordingly. Press ENTER again to confirm that the firmware version has
been updated.

Navigation menu