Yamaha DIC183 User Manual To The A9da5c2e 592d 4837 B789 F65f0c7693bd

User Manual: Yamaha DIC183 to the manual

Open the PDF directly: View PDF .
Page Count: 106

Download
Open PDF In Browser	View PDF

2012 WaveRunner

VX Sport
VX Deluxe
VX Cruiser
OWNER’S/OPERATOR’S MANUAL

U.S.A. Edition
Read this manual carefully
before operating this watercraft.

LIT-18626-09-35
F2N-F8199-12

DIC183

UF2N12E0.book Page 1 Monday, July 4, 2011 3:25 PM

Read this manual carefully before operating this watercraft. This manual
should stay with the WaveRunner if it is sold.

UF2N12E0.book Page 1 Monday, July 4, 2011 3:25 PM

Important manual information
EJU30182

EJU40400

To the owner/operator
Thank you for choosing a Yamaha watercraft.
This owner’s/operator’s manual contains information you will need for proper operation,
maintenance, and care. A thorough understanding of these simple instructions will help
you to obtain maximum enjoyment from your
new Yamaha. If you have any questions
about the operation or maintenance of your
watercraft, please consult a Yamaha dealer.
In this manual, information of particular importance is distinguished in the following ways:
This is the safety alert symbol. It is used
to alert you to potential personal injury hazards. Obey all safety messages that follow
this symbol to avoid possible injury or death.
EWJ00071

WARNING
A WARNING indicates a hazardous situation which, if not avoided, could result in
death or serious injury.
ECJ00091

NOTICE
A NOTICE indicates special precautions
that must be taken to avoid damage to the
watercraft or other property.

TIP:
A TIP provides key information to make procedures easier or clearer.

Because Yamaha has a policy of continuing
product improvement, this product may not be
exactly as described in this owner’s/operator’s manual. Specifications are subject to
change without notice.
This manual should be considered a permanent part of this watercraft and should remain
with it even if the watercraft is subsequently
sold.
EJU30222

WaveRunner VX Sport / VX Deluxe /
VX Cruiser
OWNER’S/OPERATOR’S MANUAL
©2011 by Yamaha Motor Corporation,
U.S.A.
1st Edition, June 2011
All rights reserved.
Any reprinting or unauthorized use
without the written permission of
Yamaha Motor Corporation, U.S.A.
is expressly prohibited.
Printed in U.S.A.
P/N LIT-18626-09-35

UF2N12E0.book Page 1 Monday, July 4, 2011 3:25 PM

Table of contents
General and important labels........... 1
Identification numbers .................... 1
Primary Identification (PRI-ID)
number ........................................... 1
Hull Identification Number (HIN) ........ 1
Engine serial number ........................ 1

Emission control information .......... 2
Approval label of emission control
certificate ........................................ 2
Manufactured date label .................... 3
Star labels ......................................... 3

Important labels .............................. 5
Warning labels ................................... 6
Other labels ....................................... 8

Safety information........................... 10
Limitations on who may operate
the watercraft ............................ 10
Cruising limitations ....................... 11
Operation requirements ............... 13
Recommended equipment ........... 15
Hazard information ....................... 16
Watercraft characteristics ............. 16
Water-skiing ................................. 18
Rules of the Road ........................ 19
To get more boating safety
information ................................ 23
Enjoy your watercraft
responsibly ................................ 24
Description....................................... 26
Watercraft glossary ...................... 26
Location of main components ...... 27

Start switch ......................................
Throttle lever ...................................
Steering system ...............................
Cooling water pilot outlet .................
Water separator ...............................

33
34
34
35
35

Watercraft operation....................... 37
Watercraft operation functions ..... 37
Reverse system
(VX Deluxe / VX Cruiser) ............. 37

Watercraft operation modes ......... 38
Low RPM Mode
(VX Deluxe / VX Cruiser) ............. 38

Instrument operation ...................... 40
Multifunction information center ... 40
Information display .......................... 40

Equipment operation ...................... 45
Equipment .................................... 45
Seat .................................................
Handgrip ..........................................
Reboarding step (VX Cruiser) .........
Bow eye ...........................................
Stern eyes .......................................
Cleat ................................................
Storage compartments ....................
Fire extinguisher holder and
cover ............................................

45
46
46
46
47
47
47
49

Operation and handling
requirements ................................... 51
Fuel requirements ........................ 51
Fuel ................................................. 51

Engine oil requirements ............... 52
Control function operation ............. 31
Watercraft control functions ......... 31
Remote control transmitter
(VX Deluxe / VX Cruiser) .............
Yamaha Security System
(VX Deluxe / VX Cruiser) .............
Engine stop switch ..........................
Engine shut-off switch .....................

31
32
33
33

Engine oil ......................................... 52

Draining the bilge water ............... 54
Draining the bilge water on land ...... 54
Draining the bilge water on water .... 54

UF2N12E0.book Page 2 Monday, July 4, 2011 3:25 PM

Table of contents
Transporting on a trailer ............... 55

Rustproofing .................................... 83

First-time operation......................... 56
Engine break-in ............................ 56

Maintenance .................................... 84
Maintenance ................................ 84

Pre-operation checks...................... 57

Tool kit ............................................. 84
Periodic maintenance chart ............. 85
Engine oil and oil filter ..................... 86

Pre-operation checklist .................... 57

Pre-operation check points .......... 59
Pre-launch checks ........................... 59
Post-launch checks ......................... 65

Specifications.................................. 87
Specifications................................ 87

Operation ......................................... 66
Operating your watercraft ............. 66

Trouble recovery............................. 88
Troubleshooting ........................... 88

Getting to know your watercraft .......
Learning to operate
your watercraft .............................
Riding position .................................
Launching the watercraft .................
Starting the engine on water ...........
Stopping the engine ........................
Leaving the watercraft .....................
Operating the watercraft ..................
Turning the watercraft .....................
Stopping the watercraft ...................
Operating the watercraft in reverse
(VX Deluxe / VX Cruiser) .............
Boarding the watercraft ...................
Starting off .......................................
Capsized watercraft .........................
Beaching and docking
the watercraft ...............................
Operating in weeded areas .............
After removing the watercraft
from the water ..............................

Troubleshooting chart ...................... 88

Emergency procedures ................ 91
66
67
67
67
68
68
68
69
70
71
71
74
75
76
77
77

Care and storage ............................. 78
Post-operation care ...................... 78
Flushing the cooling water
passages ...................................... 78
Cleaning the watercraft ................... 79
Battery care ..................................... 79

Long-term storage ........................ 82
Cleaning .......................................... 82
Lubrication ....................................... 82

Cleaning the jet intake and
impeller ........................................
Jumping the battery .........................
Replacing the fuses .........................
Towing the watercraft ......................
Submerged watercraft .....................

91
92
92
94
94

Consumer information ................... 95
Limited warranty ........................... 95
YAMAHA EXTENDED SERVICE
(Y.E.S.) ..................................... 97

UF2N12E0.book Page 1 Monday, July 4, 2011 3:25 PM

General and important labels
EJU30262

EJU30300

Identification numbers
Record the Primary Identification (PRI-ID)
number, Hull Identification Number (HIN), and
engine serial number in the spaces provided
for assistance when ordering genuine parts
from a Yamaha dealer. Also record and keep
these ID numbers in a separate place in case
your watercraft is stolen.

Hull Identification Number (HIN)
The HIN is stamped on a plate attached to the
aft deck.

EJU40500

Primary Identification (PRI-ID) number
The PRI-ID number is stamped on a plate attached inside the engine compartment. (See
page 45 for seat removal and installation procedures.)
MODEL:
VX1100C-L (VX Sport)
VX1100B-L (VX Deluxe)
VX1100A-L (VX Cruiser)

1 Hull Identification Number (HIN) location

EJU30311

Engine serial number
The engine serial number is stamped on a
plate attached to the engine unit. (See page
45 for seat removal and installation procedures.)

1 Primary Identification (PRI-ID) number location
PRI-I.D.

MODEL

F2N

YAMAHA MOTOR CO., LTD.
ASSEMBLED IN U.S.A. FROM AMERICAN AND JAPANESE
COMPONENTS.
ASSEMBLÉ AUX ÉTATS-UNIS DE PIÈCES AMÉRICAINES ET
JAPONAISES.

F2N

1 Engine serial number location

UF2N12E0.book Page 2 Monday, July 4, 2011 3:25 PM

General and important labels
EJU30352

Emission control information
This engine conforms to U.S. Environmental
Protection Agency (EPA) and/or California Air
Resources Board (CARB) regulations for marine SI engines applicable at the time of manufacture.
This engine is certified to operate on regular
unleaded gasoline.

ment. (See page 45 for seat removal and installation procedures.)

EJU30402

Approval label of emission control
certificate
This label is attached to the top of the cylinder
head and to the inside of the engine compart-

1 Emission control information label location

1 Emission control information label location
EMISSION CONTROL INFORMATION ENGINE FAMILY:
THIS ENGINE CONFORMS TO
CALIFORNIA AND U.S. EPA EXHAUST REGULATIONS
FOR SI MARINE ENGINES. REFER TO THE OWNER’S MANUAL FOR MAINTENANCE
SPECIFICATIONS AND ADJUSTMENTS. THIS VESSEL MEETS U.S. EPA EVAP STANDARDS.
FELS (HC+NOx/CO) :
g/kW-hr
MAX POWER :
TROLLING SPEED :
rpm
SPARK PLUG :
FUEL : UNLEADED REGULAR GASOLINE VALVE LASH (mm) IN :
CERTIFIED COMPONENTS :

kW DISPLACEMENT :
Liters
SPARK PLUG GAP (mm) :
EX :

YAMAHA MOTOR CO., LTD.

UF2N12E0.book Page 3 Monday, July 4, 2011 3:25 PM

General and important labels
EJU30431

Manufactured date label
This label is attached to the top of the cylinder
head. (See page 45 for seat removal and installation procedures.)

One Star - Low Emission
The one-star label identifies engines that
meet the Air Resources Board’s Personal
Watercraft and Outboard marine engine 2001
exhaust emission standards. Engines meeting these standards have 75% lower emissions than conventional carbureted twostroke engines. These engines are equivalent
to the U.S. EPA’s 2006 standards for marine
engines.

1
1 Manufactured date label location

EJU30440

Star labels

Two Stars - Very Low Emission
The two-star label identifies engines that meet
the Air Resources Board’s Personal Watercraft and Outboard marine engine 2004 exhaust emission standards. Engines meeting
these standards have 20% lower emissions
than One Star-Low Emission engines.

This watercraft is labeled with a California Air
Resources Board (CARB) star label. See below for a description of your particular label.

1 Star label location

Three Stars - Ultra Low Emission
The three-star label identifies engines that
meet the Air Resources Board’s Personal
Watercraft and Outboard marine engine 2008

UF2N12E0.book Page 4 Monday, July 4, 2011 3:25 PM

General and important labels
exhaust emission standards or the Sterndrive
and Inboard marine engine 2003-2008 exhaust emission standards. Engines meeting
these standards have 65% lower emissions
than One Star-Low Emission engines.

Four Stars - Super Ultra Low Emission
The four-star label identifies engines that
meet the Air Resources Board’s Sterndrive
and Inboard marine engine 2009 exhaust
emission standards. Personal Watercraft and
Outboard marine engines may also comply
with these standards. Engines meeting these
standards have 90% lower emissions than
One Star-Low Emission engines.

UF2N12E0.book Page 5 Monday, July 4, 2011 3:25 PM

General and important labels
EJU30452

Important labels
Read the following labels before using this watercraft. If have any questions, consult a Yamaha
dealer.

3
9

4
10

1
7

3
10
2

UF2N12E0.book Page 6 Monday, July 4, 2011 3:25 PM

General and important labels
EJU35913

Warning labels
If any of these labels are damaged or missing, contact a Yamaha dealer for replacements.

UF2N12E0.book Page 7 Monday, July 4, 2011 3:25 PM

General and important labels

VX Deluxe / VX Cruiser:

UF2N12E0.book Page 8 Monday, July 4, 2011 3:25 PM

General and important labels
EJU35925

Other labels

UF2N12E0.book Page 9 Monday, July 4, 2011 3:25 PM

General and important labels
The following label indicates the correct direction to upright a capsized watercraft.

UF2N12E0.book Page 10 Monday, July 4, 2011 3:25 PM

Safety information
EJU30671

The safe use and operation of this watercraft is dependent upon the use of proper
riding techniques, as well as upon the
common sense, good judgment, and expertise of the operator. Every operator
should know the following requirements
before riding the watercraft.
● Before operating the watercraft, read this
owner’s/operator’s manual, the Riding
Practice Guide, the Riding Instruction card,
and all labels on the watercraft. Also, watch
the Basic Orientation Video provided with
your watercraft. These materials should
give you an understanding of the watercraft
and its operation.
● Never allow anyone to operate this watercraft until they too have read this owner’s/operator’s manual, the Riding Practice
Guide, the Riding Instruction card, and all
labels, and, if possible, watched the Basic
Orientation Video.
Showing them the video may help reinforce
the information contained in these materials.

EJU30730

Limitations on who may
operate the watercraft
●

●

Yamaha recommends a minimum operator
age of 16 years old.
Adults must supervise use by minors.
Know the operator age and training requirements for your state. A boating safety
course is recommended and may be required in your state. You can find local rules
by contacting the United States Coast
Guard (USCG), the National Association of
State Boating Law Administrators, or your
local Power Squadron.
This watercraft is designed to carry the operator and up to 2 passengers. Never exceed the maximum load limit or allow more
than 3 persons (or 2 persons if a water-skier
is being pulled) to ride the watercraft at any
time.

Maximum load:
240 kg (530 lb)
Load is the total weight of cargo, operator, and passengers.
●

Do not operate the watercraft with any passengers on board until you have considerable practice and experience riding alone.
Operating the watercraft with passengers
requires more skill. Take the time to become accustomed to the handling charac-

UF2N12E0.book Page 11 Monday, July 4, 2011 3:25 PM

Safety information
teristics of the watercraft before trying any
difficult maneuvers.

EJU30761

Cruising limitations
●

Scan constantly for people, objects, and
other watercraft. Be alert for conditions that
limit your visibility or block your vision of
others.

●

Operate defensively at safe speeds and
keep a safe distance away from people, objects, and other watercraft.
Do not follow directly behind watercraft or
other boats.
Do not go near others to spray or splash
them with water.
Avoid sharp turns or other maneuvers that
make it hard for others to avoid you or understand where you are going.
Avoid areas with submerged objects or
shallow water.
Take early action to avoid collisions. Remember, watercraft and other boats do not
have brakes.
Do not release the throttle lever when trying
to steer away from objects—you need throttle to steer. Always check throttle and steering controls before starting the watercraft.
Ride within your limits and avoid aggressive
maneuvers to reduce the risk of loss of control, ejection, and collision.
This is a high performance boat—not a toy.
Sharp turns or jumping wakes or waves can
increase the risk of back/spinal injury (paralysis), facial injuries, and broken legs, an-

●

UF2N12E0.book Page 12 Monday, July 4, 2011 3:25 PM

Safety information
●

●

kles, and other bones. Do not jump wakes
or waves.
Do not operate the watercraft in rough water, bad weather, or when visibility is poor;
this may lead to an accident causing injury
or death. Be alert to the possibility of adverse weather. Take note of weather forecasts and the prevailing weather conditions
before setting out on your watercraft.
As with any water sport, you should not operate your watercraft without someone else
nearby. If you operate further than swimming distance from shore, you should be
accompanied by another boat or watercraft,
but make sure you stay a safe distance
away. It’s good, common sense.
Never operate in water that is less than 60
cm (2 ft) deep from the bottom of the watercraft, otherwise you increase your chance
of hitting a submerged object, which could
result in injury.

with another boat, which could result in severe injury or death.

●

Follow navigation rules, and state/provincial and local laws that apply to watercraft.

60 cm (2 ft)

●

This watercraft is not equipped with lighting
required for night operation. Do not operate
the watercraft after sunset or before dawn,
otherwise you increase the risk of colliding

UF2N12E0.book Page 13 Monday, July 4, 2011 3:25 PM

Safety information
EJU30812

Operation requirements
●

●

All riders must wear a U.S. Coast Guard
(USCG) approved personal flotation device
(PFD) that is suitable for personal watercraft use.
Wear protective clothing. Severe internal
injuries can occur if water is forced into
body cavities as a result of falling into the
water or being near the jet thrust nozzle.
Normal swimwear does not adequately protect against forceful water entry into the rectum or vagina. All riders must wear a
wetsuit bottom or clothing that provides
equivalent protection. Such clothing includes thick, tightly woven, sturdy and
snug-fitting apparel such as denim, but
does not include spandex or similar fabrics,
like those used in bicycle shorts.

1 USCG approved PFD
2 Wetsuit bottom
●

●

Eye protection is recommended to keep
wind, water, and glare from the sun out of
your eyes while you operate your watercraft. Restraining straps for eyewear are
made which are designed to float should
your eyewear fall in the water.
Footwear and gloves are recommended.
Helmets meeting Snell or DOT standards
are required for IJSBA-sanctioned races.
You must decide whether to wear a helmet
while you ride for recreation. You should

●

know that a helmet could help protect you in
certain kinds of accidents and that it could
injure you in others.
A helmet is designed to provide some head
protection. Although helmets cannot protect
against all foreseeable impacts, a helmet
might reduce your injuries in a collision with
a boat or other obstacle.
A helmet may have potential safety hazards, as well. Falling into the water could
risk the chance of the helmet catching water, commonly known as “bucketing”, and
the resulting strain on your neck could
cause choking, severe and permanent neck
injuries, or death. A helmet could also increase the risk of an accident if it reduces
your vision or hearing, or if it distracts you or
increases your fatigue.
How should you decide if a helmet’s potential safety benefits outweigh its potential
risks for you? Consider your particular
riding conditions. Consider factors such as
your riding environment and your riding
style and ability. Also consider the likelihood of traffic congestion, and the water
surface conditions.
If you decide to wear a helmet based upon
your riding circumstances, choose one
carefully. Look for a helmet designed for
personal watercraft use, if possible. Consider a helmet meeting Snell or DOT standards. If you will be engaging in closedcourse competition, follow the helmet requirements of the sanctioning organization.
Never operate the watercraft after consuming alcohol or taking other drugs.
For reasons of safety and proper care of the
watercraft, always perform the pre-operation checks listed on page 57 before operating the watercraft.

UF2N12E0.book Page 14 Monday, July 4, 2011 3:25 PM

Safety information
●

●

tercraft to avoid accidental starting or unauthorized use by children or others.

The operator and passengers should always keep their feet on the floor of the footwell when the watercraft is in motion. Lifting
your feet increases the chances of losing
your balance, or hitting objects outside the
watercraft with your feet. Do not give a ride
to children if their feet cannot reach the floor
of the footwell.
The passengers should hold on firmly, either to the person in front of them or to the
handgrip provided.
●

●

Never allow a passenger to ride in front of
the operator.
Always consult your doctor on whether it is
safe for you to ride this watercraft if you are
pregnant or in poor health.
Do not attempt to modify this watercraft.
Modifications to your watercraft may reduce
safety and reliability, and render the watercraft unsafe or illegal for use.
Attach the engine shut-off cord (lanyard) to
your left wrist and keep it free from the handlebars so that the engine stops if you, the
operator, fall off. After riding, remove the
engine shut-off cord (lanyard) from the wa-

●

Scan carefully for swimmers and stay away
from swimming areas. Swimmers are hard
to see and you could accidentally hit someone in the water.
Avoid being hit by another boat. You should
always take the responsibility to watch for
traffic; other boaters may not be watching
for you. If they do not see you, or if you maneuver more quickly than other boaters expect, you risk a collision.
Maintain a safe distance from other boats
and watercraft, and also watch for ski ropes
or fishing lines. Obey the “Rules of the
Road” and be sure to check behind you before making a turn. (See “Rules of the
Road” on page 19.)
According to the USCG, boats under 6.1 m
(20 ft) in length like your watercraft must
carry a fire extinguisher of a B-1 classification, with a capacity of two pounds or more
when navigating in waters under USCG jurisdiction. In addition, most state and local

UF2N12E0.book Page 15 Monday, July 4, 2011 3:25 PM

Safety information
boating laws also require that the fire extinguisher be approved by the USCG.

EJU30830

Recommended equipment
The following items should be carried on
board your watercraft:
● Sound-signaling device
You should carry a whistle or other soundsignaling device that can be used to signal
other boats. See “Rules of the Road” for
more information.
● Visual distress signals
It is recommended that a U.S. Coast Guard
approved pyrotechnic device be stored in a
waterproof container on your watercraft. A
mirror can also be used as an emergency
signal. Contact a Yamaha dealer or the
U.S. Coast Guard for more information.
● Watch
A watch is helpful so you will know how long
you have been operating the watercraft.
● Towline
A towline can be used to tow a disabled watercraft in an emergency.

UF2N12E0.book Page 16 Monday, July 4, 2011 3:25 PM

Safety information
EJU30870

EJU30934

Hazard information
●

●

Never start the engine or let it run for any
length of time in an enclosed area. Exhaust
fumes contain carbon monoxide, a colorless, odorless gas that may cause loss of
consciousness and death within a short
time. Always operate the watercraft in an
open area.
Do not touch the hot oil tank, muffler, or engine during or immediately after engine operation; they can cause serious burns.

Watercraft characteristics
●

●

Jet thrust turns the watercraft. Releasing
the throttle lever completely produces only
minimum thrust. If you are traveling at
speeds above trolling, you will have rapidly
decreasing ability to steer without throttle.
This model is equipped with the Yamaha
Engine Management System (YEMS) that
includes an off-throttle steering (OTS) system. It will activate at planing speeds should
you attempt to steer the watercraft after releasing the throttle lever. The OTS system
assists in turning by continuing to supply
some thrust while the watercraft is decelerating, but you can turn more sharply if you
apply throttle while turning the handlebars.
The OTS system does not function below
planing speeds or when the engine is off.
Once the engine slows down, the watercraft
will no longer turn in response to handlebar
input until you apply throttle again or you
reach trolling speed.
Practice turning in an open area without obstacles until you have a good feel for this
maneuver.
VX Sport: This watercraft is water-jet propelled. The jet pump is directly connected to
the engine. This means that jet thrust will
produce some movement whenever the engine is running. There is no “neutral” position.
VX Deluxe / VX Cruiser: This watercraft is
water-jet propelled. The jet pump is directly
connected to the engine. This means that
jet thrust will produce some movement
whenever the engine is running. There is no
“neutral” position. You are in either “forward” or “reverse”, depending upon the
shift lever position.
VX Deluxe / VX Cruiser: Do not use the reverse function to slow down or stop the wa-

UF2N12E0.book Page 17 Monday, July 4, 2011 3:25 PM

Safety information

●

tercraft as it could cause you to lose control,
be ejected, or impact the handlebars.
This could increase the risk of back/spinal
injury (paralysis), facial injuries, and broken
legs, ankles, and other bones. You could
also damage the shift mechanism.
VX Deluxe / VX Cruiser: Reverse can be
used to slow down or stop during slowspeed maneuvering, such as when docking. Once the engine is idling, shift into reverse and gradually increase engine speed.
Make sure that there are no obstacles or
people behind you before shifting into reverse.
Keep away from the intake grate while the
engine is on. Items such as long hair, loose
clothing, or PFD straps can become entangled in moving parts, resulting in severe injury or drowning.
Never insert any object into the jet thrust
nozzle while the engine is running. Severe
injury or death could result from coming in
contact with the rotating parts of the jet
pump.

2
1
1 Intake grate
2 Jet thrust nozzle
●

Stop the engine and remove the clip from
the engine shut-off switch before removing

any debris or weeds, which may have collected around the jet intake.

2
1
ST
OP

1 Clip
2 Engine shut-off switch

UF2N12E0.book Page 18 Monday, July 4, 2011 3:25 PM

Safety information
is required by law. Let the skier direct the
operator’s control of speed and direction
with hand signals.
The spotter should sit astride the rear of the
seat and hold onto the handgrip with both
feet firmly on the floor of the footwell for
proper balance while facing to the rear to
watch the skier’s hand signals and condition.

EJU30943

Water-skiing
You can use the watercraft for water-skiing if
it has the seating capacity to carry the operator, a rearward-facing spotter, and the waterskier when he or she is not skiing.
The watercraft must also have a cleat designed to pull a ski rope; do not attach the
rope to any other location.

1 Cleat

It is the watercraft operator’s responsibility to
be alert to the safety of the water-skier and
others. Know and follow all state and local water-skiing regulations in effect for the waters in
which you will be operating.
The operator should be comfortable carrying
passengers before attempting to pull a skier.
The following are some important considerations for minimizing risks while water-skiing.
● The skier should wear an approved PFD,
preferably a brightly colored one so boat
operators can see the skier.
● The skier should wear protective clothing.
Severe internal injuries can occur if water is
forced into body cavities as a result of falling
into the water. Normal swimwear does not
adequately protect against forceful water
entry into the rectum or vagina. The skier
should wear a wetsuit bottom or clothing
that provides equivalent protection.
● A second person should be on board as a
spotter to watch the skier; in most states it

1 Handgrip

1 Handgrip
●

●

Your control while pulling a water-skier is
affected by the skier’s ability, as well as water and weather conditions.
When preparing to pull a skier, operate the
watercraft at the slowest possible speed
until the watercraft is well away from the skier and slack in the ski rope is taken up.

UF2N12E0.book Page 19 Monday, July 4, 2011 3:25 PM

Safety information

●

Make sure that the rope is not looped
around anything.
After checking that the skier is ready and
that there is no traffic or other obstacles, apply enough throttle to raise the skier.
Make smooth, wide turns. The watercraft is
capable of very sharp turns, which could exceed the abilities of the skier. Keep the skier
at least 50 m (150 ft), about twice the distance of a standard ski rope, from any potential hazard.
Be alert to the hazard of the ski rope handle
snapping back at the watercraft when the
skier falls or is unable to get up on the skis.
Towing heavy or bulky objects other than
skiers, such as another boat or watercraft,
can cause loss of steering control and create a hazardous condition. If you must tow
another boat in an emergency situation, operate slowly and cautiously.

EJU30961

Rules of the Road
Your Yamaha watercraft is legally considered a powerboat. Operation of the watercraft must be in accordance with the rules
and regulations governing the waterway
on which it is used.
Just as there are rules that apply when you
are driving on streets and highways, there are
waterway rules that apply when you are operating your watercraft. These rules are used internationally, and are also enforced by the
United States Coast Guard and local agencies. You should be aware of these rules, and
follow them whenever you encounter another
vessel on the water.
Several sets of rules prevail according to geographic location, but are all basically the same
as the International Rules of the Road. The
rules presented here in this owner’s/operator’s manual are condensed, and have been
provided for your convenience only. Consult
your local U.S. Coast Guard Auxiliary or Department of Motor Vehicles for a complete set
of rules governing the waters in which you will
be operating your watercraft.
Steering and sailing rules
Whenever two vessels on the water meet one
another, one vessel has the right-of-way; it is
called the “stand-on” vessel. The vessel that
does not have the right-of-way is called the
“give-way” or “burdened” vessel. These rules
determine which vessel has the right-of-way,
and what each vessel should do.
Stand-on vessel
The vessel with the right-of-way has the duty
to continue its course and speed, except to
avoid an immediate collision. When you maintain your direction and speed, the other vessel
will be able to determine how best to avoid
you.

UF2N12E0.book Page 20 Monday, July 4, 2011 3:25 PM

Safety information
Give-way vessel
The vessel which does not have the right-ofway has the duty to take positive and timely
action to stay out of the way of the stand-on
vessel. Normally, you should not cross in front
of the vessel with the right-of-way. You should
slow down or change directions briefly and
pass behind the other vessel. You should always move in such a way that the operator of
the other vessel can see what you are doing.
The General Prudential Rule regarding the
right-of-way is that if a collision appears unavoidable, neither boat has the right-of-way.
Both boats must avoid the collision.
In other words, follow the standard rules except when a collision will occur unless both
vessels try to avoid each other. If that is the
case, both vessels become give-way vessels.
Rules when encountering vessels
There are three main situations that you may
encounter with other vessels which could lead
to a collision unless the Steering Rules are followed:
Meeting: you are approaching another vessel
head-on
Crossing: you are traveling across another
vessel’s path
Overtaking: you are passing or being passed
by another vessel
In the following illustration, your watercraft is
in the center. You should give the right-of-way
to any vessels shown in the white area (you
are the give-way vessel). Any vessels in the
shaded area must yield to you (they are the

give-way vessels). Both you and the meeting
vessel must alter course to avoid each other.

Meeting
If you are meeting another power-driven vessel head on, and are close enough to run the
risk of collision, neither of you has the right-ofway. Both of you should alter course to avoid
an accident. You should keep the other vessel
on your port (left) side. This rule does not apply if both of you will clear one another if you
continue on your set course and speed.

Crossing
When two power-driven vessels are crossing
each other’s path close enough to run the risk
of collision, the vessel which has the other on
the starboard (right) side must keep out of the
way of the other. If the other vessel is on your
starboard (right) side, you must keep out of its
way; you are the give-way vessel. If the other
vessel is on your port (left) side, remember
that you should maintain course and direction,

UF2N12E0.book Page 21 Monday, July 4, 2011 3:25 PM

Safety information
provided the other vessel gives you the rightof-way as it should.

Overtaking
If you are passing another vessel, you are the
give-way vessel. This means that the other
vessel is expected to maintain its course and
speed. You must stay out of its way until you
are clear of it. Likewise, if another vessel is
passing you, you should maintain your speed
and direction so that the other vessel can
steer itself around you.
Other special situations
There are three other rules you should be
aware of when riding your watercraft around
other vessels.
Narrow channels and bends
When navigating in narrow channels, you
should keep to the right when it is safe and
practical to do so. If the operator of a powerdriven vessel is preparing to go around a
bend that may obstruct the view of other water
vessels, the operator should sound a prolonged blast of four to six seconds on the
whistle. If another vessel is around the bend,
it too should sound the whistle. Even if no reply is heard, however, the vessel should still
proceed around the bend with caution. If you
navigate such waters with your watercraft,
you will need to carry a portable air horn,
available from local marine supply stores.

Fishing vessel right-of-way
All vessels fishing with nets, lines, or trawls
are considered to be “fishing vessels” under
the International Rules. Vessels with trolling
lines are not considered fishing vessels. Fishing vessels have the right-of-way regardless
of position. Fishing vessels cannot, however,
impede the passage of other vessels in narrow channels.
Sailing vessel right-of-way
Sailing vessels should normally be given the
right-of-way. The exceptions to this are:
(1) When the sailing vessel is overtaking the
power-driven vessel, the power-driven
vessel has the right-of-way.
(2) Sailing vessels should keep clear of any
fishing vessel.
(3) In a narrow channel, a sailing vessel
should not hamper the safe passage of a
power-driven vessel that can navigate
only in such a channel.
Reading buoys and other markers
The waters of the United States are marked
for safe navigation by the lateral system of
buoyage. Simply put, buoys and markers
have an arrangement of shapes, colors, numbers, and lights to show which side of the
buoy a boater should pass on when navigating in a particular direction. The markings on
these buoys are oriented from the perspective
of being entered from seaward (the boater is
going towards the harbor). Red buoys are
passed on your starboard (right) side when
proceeding from open water into the harbor,
and black buoys are to your port (left) side. An
easy way to remember the meaning of the
colors is the phrase “red right returning”.
When navigating out of the harbor, your position with respect to the buoys should be reversed; red buoys should be to port and black
buoys to starboard.

UF2N12E0.book Page 22 Monday, July 4, 2011 3:25 PM

Safety information
Many bodies of water used by boaters are entirely within the boundaries of a particular
state. The Uniform State Waterway Marking
System has been devised for these waters.
This system uses buoys and signs with distinctive shapes and colors to show regulatory

or advisory information. These markers are
white with black letters and orange borders.
They signify speed zones, restricted areas,
danger areas, and general information.

UF2N12E0.book Page 23 Monday, July 4, 2011 3:25 PM

Safety information
Remember, markings may vary by geographic location. Always consult local boating authorities before riding your watercraft in
unfamiliar waters.

EJU30982

To get more boating safety
information
Be informed about boating safety. Additional
publications and information can be obtained
from many organizations, including the following.
United States Coast Guard
Consumer Affairs Staff (G-BC)
Office of Boating, Public, and Consumer Affairs
U.S. Coast Guard Headquarters
Washington, D.C. 20593-0001
http://www.uscgboating.org/
Other sources
You can find local rules by contacting the National Association of State Boating Law Administrators, or your local Power Squadron.
Watercraft Education and Training
The Online Boating Safety Course, available
through the watercraft section of the yamahamotor.com website, is a free, 50 question
learning course available to the public. Upon
successful completion of 80 percent or better,
the user can request a certificate of completion by mail or can download one immediately. The Online Boating Safety Course,
provided by the Boat/US Foundation, is approved by the National Association of State
Boating Law Administrators (NASBLA) and
recognized by the United States Coast
Guard. This course meets the education requirement for those states that recognize nonproctored, NASBLA-approved courses.
Yamaha is the watercraft industry’s leading
manufacturer to build awareness and support
for boating education. In 1997, Yamaha
launched its GET W.E.T. (Watercraft Education and Training) initiative and has since
reached out to over one million Americans
promoting the benefits of boating education.

UF2N12E0.book Page 24 Monday, July 4, 2011 3:25 PM

Safety information
The Online Boating Safety Course:
http://www.boatus.org/

EJU30991

Enjoy your watercraft
responsibly
You share the areas you enjoy when riding
your watercraft with others and with nature.
So your enjoyment includes a responsibility to
treat these other people, and the lands, waters, and wildlife with respect and courtesy.
Whenever and wherever you ride, think of
yourself as the guest of those around you. Remember, for example, that the sound of your
watercraft may be music to you, but it could be
just noise to others. And the exciting splash of
your wake can make waves others won’t enjoy.
Avoid riding close to shoreline homes and waterfowl nesting areas or other wildlife areas,
and keep a respectful distance from fishermen, other boats, swimmers, and populated
beaches. When travel in areas like these is
unavoidable, ride slowly and obey all laws.
Proper maintenance is necessary to ensure
that the exhaust emission and sound levels of
your watercraft will continue to be within regulated limits. You have the responsibility to
make sure that the recommended maintenance in this owner’s/operator’s manual is
carried out.
Remember, pollution can be harmful to the
environment. Do not refuel or add oil where a
spill could cause damage to nature. Remove
your watercraft from the water and move it
away from the shoreline before refueling. Dispose of water and any fuel and oil residue in
the engine compartment according to local
regulations. And keep your surroundings
pleasant for the people and wildlife that share
the waterways: don’t litter.
When you ride responsibly, with respect and
courtesy for others, you help ensure that our

UF2N12E0.book Page 25 Monday, July 4, 2011 3:25 PM

Safety information
waterways stay open for the enjoyment of a
variety of recreational opportunities.

UF2N12E0.book Page 26 Monday, July 4, 2011 3:25 PM

Description
EJU40302

Watercraft glossary
Trolling speed
“Trolling” is the lowest maneuvering speed. You are applying little or no throttle. The watercraft
is down in the water, and there is no wake.
Sub-planing speed
“Sub-planing” is a medium speed. The bow of the watercraft is slightly up from the water surface, but you are still traveling through the water. There is a wake.
Planing speed
“Planing” is a faster speed. The watercraft is more level and is skimming on top of the water.
There is a wake.
Bow
The front end of the watercraft.
Stern
The rear end of the watercraft.
Starboard
The right side of the watercraft when facing forward.
Port
The left side of the watercraft when facing forward.
Bilge water
Water that has collected in the engine compartment.
Yamaha Engine Management System (YEMS)
YEMS is an integrated, computerized management system that controls and adjusts ignition
timing, fuel injection, engine diagnostics, and the off-throttle steering (OTS) system.

UF2N12E0.book Page 27 Monday, July 4, 2011 3:25 PM

Description
EJU31011

Location of main components
Exterior

9
8
7
5

1
2
3
4
5
6
7
8
9

Hood
Handlebars
Seat (page 45)
Footwell
Bow eye (page 46)
Fuel filler cap (page 51)
Cooling water pilot outlet (page 35)
Gunwale
Sponson

UF2N12E0.book Page 28 Monday, July 4, 2011 3:25 PM

Description

3
2
1

4
10

5
6

1
2
3
4
5
6
7
8
9
10
11

Boarding platform
Cleat (page 47)
Handgrip (page 46)
Reboarding step (VX Cruiser) (page 46)
Jet thrust nozzle
Reverse gate (VX Deluxe / VX Cruiser)
(page 37)
Ride plate
Stern eye (page 47)
Stern drain plug (page 54)
Speed sensor
Intake grate

UF2N12E0.book Page 29 Monday, July 4, 2011 3:25 PM

Description
1

10
1
2
3
4
5
6
7
8
9

Start switch (page 33)
Engine shut-off switch (page 33)
Clip (page 33)
Engine shut-off cord (lanyard) (page 33)
Engine stop switch (page 33)
Glove compartment (page 48)
Multifunction information center (page 40)
Rearview mirror
Remote control transmitter (VX Deluxe /
VX Cruiser) (page 31)
10 Beverage holder (VX Deluxe / VX Cruiser)
(page 49)
11 Shift lever (VX Deluxe / VX Cruiser) (page
37)
12 Throttle lever (page 34)

UF2N12E0.book Page 30 Monday, July 4, 2011 3:25 PM

Description
Engine compartment

1
2
3
4
5
6
7
8
9

Water separator (page 35)
Fuel tank
Air filter case
Battery (page 60)
Flushing hose connector
Electrical box
Spark plug/Spark plug cap/Ignition coil
Oil tank filler cap/Dipstick
Oil tank

UF2N12E0.book Page 31 Monday, July 4, 2011 3:25 PM

Control function operation
EJU31024

Watercraft control functions
EJU41370

in the transmitter holder in the beverage holder, so that it is not lost.

Remote control transmitter
(VX Deluxe / VX Cruiser)
The Yamaha Security System and Low RPM
Mode settings can be selected by operating
the remote control transmitter. (See page 32
for Yamaha Security System setting procedures and page 38 for Low RPM Mode activation procedures.)

1 Transmitter holder
ECJ00752

NOTICE
●

1 Remote control transmitter

Since the watercraft is programmed to recognize the internal code from this transmitter
only, the settings can only be selected with
this transmitter.
If you accidentally lose your remote control
transmitter or if it is not operating properly,
contact a Yamaha dealer.
When operating the watercraft, always keep
the transmitter with you, such as by storing it

●

The remote control transmitter is not
completely waterproof. Do not submerge the transmitter or operate it underwater.
If
the
transmitter
is
submerged, dry it with a soft, dry cloth,
and then check that it is operating properly. If the transmitter is not operating
properly, contact a Yamaha dealer.
Keep the remote control transmitter
away from high temperatures and do not
place it in direct sunlight.
Do not drop the remote control transmitter, subject it to strong shocks, or place
any heavy items on it.
Use a soft, dry cloth to clean the remote
control transmitter. Do not use detergent, alcohol, or other chemicals.
Do not attempt to disassemble the remote control transmitter yourself. Otherwise, the transmitter may not operate
properly. If the transmitter needs a new
battery, contact a Yamaha dealer. Refer
to local hazardous waste regulations
when disposing of transmitter batteries.

This device complies with Part 15 of the FCC
Rules. Operation is subject to the following

UF2N12E0.book Page 32 Monday, July 4, 2011 3:25 PM

Control function operation
two conditions: (1) this device may not cause
harmful interference, and (2) this device must
accept any interference received, including interference that may cause undesired operation.

Number of
beeps

ECJ00030

NOTICE
Changes or modifications not expressly
approved by the party responsible for
compliance could void the user’s authority to operate the remote control transmitter.
EJU31384

Yamaha Security System (VX Deluxe /
VX Cruiser)
The Yamaha Security System functions to
help prevent unauthorized use or theft of the
watercraft. The lock and unlock modes of the
security system can be selected by operating
the remote control transmitter that is included
with this watercraft. The engine cannot be
started if the lock mode of the security system
is selected. The engine can only be started if
the unlock mode is selected. (See page 31 for
information on the remote control transmitter.)

TIP:
The Yamaha Security System settings can
only be selected while the engine is stopped.

Yamaha Security
System mode

“SECURITY” indicator light

Lock

Goes off

Unlock
(normal operation
mode)

Comes
on

Unlock
(Low RPM Mode)

Comes
on

TIP:
The beeper sounds two times for the normal operation mode or three times for the
Low RPM Mode. (See page 38 for Low
RPM Mode activation procedures.)
● If the remote control transmitter is operated
while the multifunction information center is
in the standby state, the center will perform
the initial operation, and then the setting is
selected.
To select the lock mode:
Push the lock button on the remote control
transmitter briefly. The beeper sounds once
and the “SECURITY” indicator light blinks
once, then goes off. This indicates the lock
mode is selected.
●

EJU36106

Yamaha Security System settings
The Yamaha Security System settings will be
confirmed by the number of beeps when the
remote control transmitter is operated, and by
the “SECURITY” indicator light of the multifunction information center. (See page 40 for
information on the multifunction information
center.)

1 Lock button
2 “SECURITY” indicator light

To select the unlock mode:
Push the “L-Mode” (unlock) button on the remote control transmitter briefly. The beeper
sounds two or three times and the “SECURI-

UF2N12E0.book Page 33 Monday, July 4, 2011 3:25 PM

Control function operation
TY” indicator light blinks two or three times,
then comes on. This indicates the unlock
mode is selected.

L-Mode

Insert the clip under the engine shut-off switch
before starting the engine.

STO
P

3
1 Engine shut-off switch
2 Clip
3 Engine shut-off cord (lanyard)

1 “L-Mode” (unlock) button
2 “SECURITY” indicator light
EJU31152

Engine stop switch “ ”
The engine stop switch (red button) stops the
engine when the switch is pushed.

When the engine is not running, remove the
clip from the engine shut-off switch to prevent
accidental starting or unauthorized operation
by children or others.

1
1 Engine stop switch
EJU41650
EJU31163

Engine shut-off switch “

”

The engine shut-off switch automatically
stops the engine when the clip, on the end of
the engine shut-off cord (lanyard), is removed
from the switch, such as if the operator falls off
the watercraft.

Start switch “

”

ECJ01310

NOTICE
Do not run the engine over 4000 r/min on
land. Also, do not run the engine for more
than 15 seconds without supplying water,
otherwise the engine could overheat.
The start switch (green button) starts the engine when the switch is pushed.
Release the start switch as soon as the engine starts to run. If the engine does not start

UF2N12E0.book Page 34 Monday, July 4, 2011 3:25 PM

Control function operation
in 5 seconds, release the start switch, wait 15
seconds, and then try again. NOTICE: Never
push the start switch while the engine is
running. Do not operate the start switch
for more than 5 seconds, otherwise the
battery will be discharged and the engine
will not start. Also, the starter motor could
be damaged. [ECJ01040]

EJU31211

Throttle lever
The throttle lever increases the engine speed
when the lever is squeezed.

1
STAR
T

1 Throttle lever

The throttle lever returns automatically to its
fully closed (idle) position when released.
EJU31261

1 Start switch

The engine will not start under any of the following conditions:
● Clip is removed from the engine shut-off
switch.
● Throttle lever is squeezed.
● VX Deluxe / VX Cruiser: Lock mode of the
Yamaha Security System has been selected. (See page 32 for Yamaha Security System setting procedures.)

Steering system
By turning the handlebars in the direction you
wish to travel, the angle of the jet thrust nozzle
is changed, and the direction of the watercraft
is changed accordingly.

2
1 Handlebar
2 Jet thrust nozzle

UF2N12E0.book Page 35 Monday, July 4, 2011 3:25 PM

Control function operation
Since the strength of the jet thrust determines
the speed and degree of a turn, throttle must
always be applied when attempting a turn, except at trolling speed.
This model is equipped with the Yamaha Engine Management System (YEMS) that includes an off-throttle steering (OTS) system.
It will activate at planing speeds should you
attempt to steer the watercraft after releasing
the throttle lever. The OTS system assists in
turning by continuing to supply some thrust
while the watercraft is decelerating, but you
can turn more sharply if you apply throttle
while turning the handlebars. The OTS system does not function below planing speeds
or when the engine is off. Once the engine
slows down, the watercraft will no longer turn
in response to handlebar input until you apply
throttle again or you reach trolling speed.

check the jet intake for clogging. (See page
91 for information on the jet intake.)

TIP:
●

●

It will take about 60 seconds for the water to
reach the outlet after the engine is started.
Water discharge may not be constant when
the engine is running at idling speed. If this
occurs, apply a little throttle to make sure
that water discharges properly.

EJU40322

Water separator
The water separator prevents water from entering the fuel tank by collecting any water that
has entered the fuel tank breather hose if the
watercraft was capsized.
If water has collected in the water separator,
drain it by loosening the drain screw.

EJU35974

Cooling water pilot outlet
When the engine is running, some of the cooling water that is circulated in the engine is discharged from the cooling water pilot outlet.

1
1 Water separator

1 Cooling water pilot outlet

There is a cooling water pilot outlet on the port
(left) side of the watercraft. To check for proper operation of the cooling system, make sure
that water is being discharged from the cooling water pilot outlet. If water is not being discharged from the outlet, stop the engine and

1 Drain screw

UF2N12E0.book Page 36 Monday, July 4, 2011 3:25 PM

Control function operation
To drain water from the water separator:
(1) Place a drain pan or dry cloth under the
water separator.
(2) Gradually loosen the drain screw to drain
the water. Catch the draining water in the
drain pan or soak it up with the dry cloth
so that it does not spill into the engine
compartment. If any water spills into the
watercraft, be sure to wipe it up with a dry
cloth.
(3) Securely tighten the drain screw until it
stops.

UF2N12E0.book Page 37 Monday, July 4, 2011 3:25 PM

Watercraft operation
EJU40011

Watercraft operation functions

will lower and the watercraft will start
moving in reverse at trolling speed.

EJU40520

Reverse system (VX Deluxe /
VX Cruiser)
EWJ01230

WARNING
●

●

Do not use the reverse function to slow
down or stop the watercraft as it could
cause you to lose control, be ejected, or
impact the handlebars.
Make sure that there are no obstacles or
people behind you before shifting into
reverse.
Do not touch the reverse gate while the
shift lever is being operated, otherwise
you could be pinched.

When the shift lever is moved to the reverse
position, the reverse gate lowers and deflects
the water jet being discharged from the jet
thrust nozzle. This allows the watercraft to
move in reverse.
To shift into reverse:
(1) Release the throttle lever and let the engine speed return to idle.
(2) Pull the shift lever rearward until it stops
in the reverse position. The reverse gate

1 Shift lever
2 Reverse position
3 Forward position

2
1

1 Reverse gate
2 Forward position
3 Reverse position

To shift into forward:
(1) Release the throttle lever and let the engine speed return to idle.
(2) Push the shift lever forward until it stops
in the forward position. The reverse gate
will rise and the watercraft will start moving forward at trolling speed.

UF2N12E0.book Page 38 Monday, July 4, 2011 3:25 PM

Watercraft operation
EJU40000

Watercraft operation modes

Number of
beeps

Low RPM Mode
operation

“LMODE”
indicator
light

Activated

Comes
on

Deactivated

Goes off

EJU31417

Low RPM Mode (VX Deluxe /
VX Cruiser)
The Low RPM Mode is a function that limits
the maximum engine speed to approximately
90% of the maximum engine speed in the normal mode.
The Low RPM Mode can only be activated
and deactivated by operating the remote control transmitter that is included with this watercraft. (See page 31 for information on the
remote control transmitter.)

TIP:
If the remote control transmitter is operated
while the multifunction information center is in
the standby state, the center performs the initial operation, and then the setting is selected.
To activate the Low RPM Mode:
Push the “L-Mode” (unlock) button on the remote control transmitter for more than 4 seconds. Once the beeper sounds three times
and the “SECURITY” indicator light blinks
three times, then comes on, the “L-MODE” indicator light comes on and the Low RPM
Mode is activated.

TIP:

1 Remote control transmitter

If the Low RPM Mode is activated immediately after the information display turns off, the
“L-MODE” indicator light will not come on. The

TIP:
The Low RPM Mode can only be activated
when the engine is stopped in the unlock
mode of the Yamaha Security System.
Activating and deactivating the Low RPM
Mode
Activation of the Low RPM Mode will be confirmed by the number of beeps when the remote control transmitter is operated, and by
the “L-MODE” indicator light of the multifunction information center. (See page 40 for information on the multifunction information
center.)

UF2N12E0.book Page 39 Monday, July 4, 2011 3:25 PM

Watercraft operation
“L-MODE” indicator light will come on when
the engine is started.

L-Mode

1 “L-Mode” (unlock) button

1 “SECURITY” indicator light
2 “L-MODE” indicator light

To deactivate the Low RPM Mode:
Push the “L-Mode” (unlock) button on the remote control transmitter for more than 4 seconds. Once the beeper sounds two times and
the “SECURITY” indicator light blinks two
times, then comes on, the “L-MODE” indicator
light goes off and the Low RPM Mode is deactivated. When the Low RPM Mode is deactivated, the watercraft returns to the normal
operation mode.

UF2N12E0.book Page 40 Monday, July 4, 2011 3:25 PM

Instrument operation
EJU31458

Multifunction information
center
The multifunction information center displays
various watercraft information.

onds after the engine stops, the center will
turn off and enter a standby state. When the
engine is started again, the displays return to
their state before the center turned off, and
then the center starts to operate normally.
EJU35024

1 2

4 5

Information display
The information display shows watercraft operating conditions.

1 “SECURITY” indicator light (VX Deluxe /
VX Cruiser)
2 Select button
3 Information display
4 “L-MODE” indicator light (VX Deluxe /
VX Cruiser)
5 “WARNING” indicator light

Multifunction information center initial operation
When the multifunction information center is
activated, all of the display segments come
on. After 2 seconds, the warning indicators in
the information display go off, and then the
center starts to operate normally.
If only the multifunction information center is
activated, the “WARNING” indicator light
blinks once.

TIP:

5
1
2
3
4
5
6
7
8

6 7 8

Tachometer
Speedometer
Hour meter/voltmeter
Fuel level meter
Check engine warning indicator
Engine overheat warning indicator
Oil pressure warning indicator
Fuel level warning indicator

EJU31503

Speedometer
The speedometer shows the watercraft speed
against water.
By switching the display units, the speed can
be shown in kilometers per hour “km/h” or
miles per hour “mph”.

VX Deluxe / VX Cruiser: The “SECURITY” indicator light also comes on as part of the initial
operation.
The “SECURITY” indicator light will go off
when the engine is started.
Multifunction information center standby
state
If the multifunction information center does
not receive any operation input within 25 sec-

UF2N12E0.book Page 41 Monday, July 4, 2011 3:25 PM

Instrument operation
TIP:
“mph” is selected as the display unit at the
Yamaha factory.

The outer numbers × 1000 r/min and display
segments on the meter show the engine
speed.

1 Speedometer

To switch the speedometer display units:
Push the select button for at least 1 second,
within 10 seconds after the multifunction information center is activated. The speedometer
display changes.

1 Tachometer
EJU31555

Hour meter/voltmeter
The hour meter/voltmeter has both an hour
meter function and a voltmeter function. By
switching the meter, it can be used as either
an hour meter or a voltmeter.

TIP:
The hour meter is selected at the Yamaha
factory.

2
1 Speedometer
2 Select button
EJU31463

Tachometer
The tachometer shows the engine speed.

1 Hour meter/voltmeter

Hour meter
The hour meter shows the total number of
hours that the engine has been running since
the watercraft was new.

TIP:
The elapsed time will be kept even if the battery terminals have been disconnected.

UF2N12E0.book Page 42 Monday, July 4, 2011 3:25 PM

Instrument operation
To switch to the hour meter from the voltmeter:
Push the select button for at least 1 second after the multifunction information center is activated for more than 10 seconds. The display
switches to the hour meter from the voltmeter.

vated for more than 10 seconds. The display
switches to the voltmeter from the hour meter.

2
1 Voltmeter
2 Select button
EJU31514

2
1 Hour meter
2 Select button

Voltmeter
The voltmeter shows the battery voltage.
When the battery voltage is normal, the voltmeter displays approximately 12 volts.
If the battery voltage has dropped significantly, “LO” is displayed on the voltmeter. If the
battery voltage has risen significantly, “HI” is
displayed. If “LO” or “HI” is displayed, immediately return to shore and have a Yamaha
dealer service the watercraft.
To switch to the voltmeter from the hour
meter:
Push the select button for at least 1 second after the multifunction information center is acti-

Fuel level meter
The fuel level meter shows the amount of fuel
remaining in the fuel tank. The amount of remaining fuel is shown using eight display segments, which disappear two at a time as the
fuel level decreases.

TIP:
The accuracy of the fuel level meter varies depending on the operating conditions. Use this
function as a reference only.

1 Fuel level meter
EJU31566

Fuel level warning
If the fuel remaining in the fuel tank drops to
about 13 L (3.4 US gal, 2.9 Imp. gal), the lowest two fuel level segments, the fuel level
warning indicator, and the “WARNING” indi-

UF2N12E0.book Page 43 Monday, July 4, 2011 3:25 PM

Instrument operation
cator light blink, and the buzzer sounds intermittently.

(See page 52 for information on checking the
engine oil level.) If the oil level is sufficient,
have a Yamaha dealer check the watercraft.

TIP:
Push the select button on the multifunction information center to stop the buzzer.
EJU31609

If the fuel level warning is activated, refill the
fuel tank as soon as possible. (See page 51
for information on filling the fuel tank.)
After the fuel tank is refilled, the warning signals will be cleared when the engine is restarted.

Engine overheat warning
If the engine temperature rises significantly,
the engine overheat warning indicator and the
“WARNING” indicator light blink, and the
buzzer sounds intermittently. Then, the engine overheat warning indicator and the
“WARNING” indicator light stop blinking and
remain on, and the buzzer sounds continuously. At the same time, the maximum engine
speed is limited.

TIP:
Push the select button on the multifunction information center to stop the buzzer.
EJU31626

Oil pressure warning
If the oil pressure drops significantly, the oil
pressure warning indicator and the “WARNING” indicator light blink, and the buzzer
sounds intermittently. At the same time, the
maximum engine speed is limited.

If the oil pressure warning is activated, immediately reduce the engine speed, return to
shore, and then check the engine oil level.

If the engine overheat warning is activated,
immediately reduce the engine speed, return
to shore, and then make sure that water is being discharged from the cooling water pilot
outlet while the engine is running. If there is no
discharge of water, stop the engine, and then
check the jet intake for clogging. (See page
91 for information on the jet intake.) NOTICE:
If you cannot locate and correct the cause
of the overheating, consult a Yamaha dealer. Continuing to operate at higher speeds

UF2N12E0.book Page 44 Monday, July 4, 2011 3:25 PM

Instrument operation
could result in severe engine damage.
[ECJ00041]

TIP:
Push the select button on the multifunction information center to stop the buzzer.
EJU31634

Check engine warning
If a sensor malfunction or a short circuit is detected, the check engine warning indicator
and the “WARNING” indicator light blink, and
the buzzer sounds intermittently.

If the check engine warning is activated, immediately reduce the engine speed, return to
shore, and have a Yamaha dealer check the
engine.

TIP:
Push the select button on the multifunction information center to stop the buzzer.

UF2N12E0.book Page 45 Monday, July 4, 2011 3:25 PM

Equipment operation
EJU40333

Equipment
EJU31036

Seat

To remove the seat:
(1) Pull the seat latch up, and then lift up the
rear of the seat.

The seat is removable.
Remove the seat to access the engine compartment.
VX Sport / VX Deluxe:

1
1 Seat latch

(2) Pull the seat rearward and remove it.

VX Cruiser:

To install the seat:
(1) Insert the projections on the front of the
seat into the stays on the deck.

UF2N12E0.book Page 46 Monday, July 4, 2011 3:25 PM

Equipment operation
(2) Push the rear of the seat down to securely lock it in place.

reboarding step is not designed to support the watercraft’s weight. If the reboarding step breaks, the watercraft could fall,
which could result in severe injury. [EWJ01211]

EJU31363

Handgrip
The handgrip is used when boarding the watercraft from the water and when the spotter is
facing rearward. WARNING! Do not use the
handgrip to lift the watercraft. The handgrip is not designed to support the watercraft’s weight. If the handgrip breaks, the
watercraft could fall, which could result in
severe injury. [EWJ00021]

1 Reboarding step

1
ECJ00742

NOTICE
Use the reboarding step only to board the
watercraft in the water. Do not use the reboarding step for any other purpose. The
watercraft can be damaged.
1 Handgrip
EJU34864

Reboarding step (VX Cruiser)
The reboarding step is used to assist in reboarding the watercraft from the water.
When boarding the watercraft, push the reboarding step down until it stops. The step returns automatically to its original position
when released. WARNING! Do not use the
reboarding step to lift the watercraft. The

EJU34872

Bow eye
The bow eye is used to attach a rope to the
watercraft when transporting, mooring, or

UF2N12E0.book Page 47 Monday, July 4, 2011 3:25 PM

Equipment operation
towing it in an emergency. (See page 94 for
information on towing the watercraft.)

breaks, the watercraft could fall, which
could result in severe injury. [EWJ01510]

1
1

1 Bow eye

1 Cleat

EJU34881

EJU31683

Stern eyes

Storage compartments

The stern eyes are used to attach a rope to
the watercraft when transporting or mooring it.

This watercraft is equipped with the following
storage compartments.
The storage compartments are not designed
to be waterproof. If you carry objects that must
be kept dry, put them in a waterproof bag.
Make sure that the storage compartments are
closed securely before operating the watercraft.
EJU31715

1
1 Stern eye
EJU40420

Cleat
The cleat is used to attach a ski rope to the
watercraft when pulling a water-skier.
WARNING! Do not use the cleat to lift the
watercraft. The cleat is not designed to
support the watercraft’s weight. If the cleat

Bow storage compartment
The bow storage compartment is located under the hood.

UF2N12E0.book Page 48 Monday, July 4, 2011 3:25 PM

Equipment operation
To open the bow storage compartment:
Pull the hood latch up, and then lift up the rear
of the hood.

To close the bow storage compartment:
Push the rear of the hood down to securely
lock it in place.

1 Hood latch

To drain water from the bow storage compartment:
(1) Remove the drain plug on the bottom of
the storage compartment to drain the water into the engine compartment.

1
1
1 Bow storage compartment

Bow storage compartment:
Capacity:
50.0 L (13.2 US gal, 11.0 Imp.gal)
Load limit:
5.0 kg (11 lb)

1 Drain plug

(2) Securely install the drain plug in its original position.
EJU41550

Glove compartment
The glove compartment is located in front of
the seat.
The glove compartment is removable.

UF2N12E0.book Page 49 Monday, July 4, 2011 3:25 PM

Equipment operation
To open the glove compartment:
Slide the glove compartment latch toward
you, and then lift up the lid.

To close the glove compartment:
Push the lid down to securely lock it in place.

EJU41420

Beverage holder (VX Deluxe / VX Cruiser)
The beverage holder is located in the glove
compartment. (See page 48 for information
on the glove compartment.)
The beverage holder is removable.

1 Glove compartment latch

1
1
1 Glove compartment

Glove compartment:
Capacity:
7.0 L (1.8 US gal, 1.5 Imp.gal)
Load limit:
1.5 kg (3 lb)

1 Beverage holder

Do not place any items in the beverage holder
while riding. Otherwise, the items may fall out
of the beverage holder.
EJU40991

Fire extinguisher holder and cover
The fire extinguisher holder and cover are located in the bow storage compartment.

UF2N12E0.book Page 50 Monday, July 4, 2011 3:25 PM

Equipment operation
To use the fire extinguisher holder and cover:
(1) Pull the hood latch up, and then lift up the
rear of the hood.

hood is securely closed before using the
watercraft.

1 Hood latch

(2) Unhook the band and remove the fire extinguisher cover.

1 Band
2 Fire extinguisher holder and cover

(3) Place the fire extinguisher in the holder,
and then place the cover over the fire extinguisher.
(4) Securely fasten the cover and the fire extinguisher with the band.
(5) Push the rear of the hood down to securely lock it in place. Make sure that the

UF2N12E0.book Page 51 Monday, July 4, 2011 3:25 PM

Operation and handling requirements
EJU31822

Fuel requirements
EJU37165

Fuel
EWJ00282

WARNING
●

●

Gasoline and gasoline vapors are extremely flammable. To avoid fires and
explosions and to reduce the risk of injury when refueling, follow these instructions.
Gasoline is poisonous and can cause injury or death. Handle gasoline with care.
Never siphon gasoline by mouth. If you
should swallow some gasoline, inhale a
lot of gasoline vapor, or get some gasoline in your eyes, see your doctor immediately. If gasoline spills on your skin,
wash with soap and water. If gasoline
spills on your clothing, change your
clothes.

ECJ00321

NOTICE
●

●

Do not use leaded gasoline. Leaded gasoline can seriously damage the engine.
Avoid getting water and contaminants in
the fuel tank. Contaminated fuel can
cause poor performance and engine
damage. Use only fresh gasoline that
has been stored in clean containers.
Recommended fuel:
Regular unleaded gasoline with a
minimum octane rating of
86
(Pump octane number) = (R + M)/2
90 (Research octane number)

Gasohol
There are two types of gasohol: gasohol containing ethanol and that containing methanol.
Gasohol containing ethanol can be used if
ethanol content does not exceed 10% and the

fuel meets the minimum octane ratings. E-85
is a fuel blend containing 85% ethanol and
therefore must not be used in this watercraft.
All ethanol blends containing more than 10%
ethanol can cause fuel system damage or engine performance problems.
Yamaha does not recommend gasohol containing methanol because it can cause fuel
system damage and engine performance
problems.
To fill the fuel tank:
(1) Before refueling, stop the engine. Do not
stand or sit on the watercraft. Never refuel while smoking, or while in the vicinity of
sparks, open flames, or other sources of
ignition.
(2) Place the watercraft in a well-ventilated
area and in a horizontal position.
(3) Remove the seat, and then check the fuel
level. (See page 45 for seat removal and
installation procedures.)
(4) Loosen the fuel filler cap and remove it.

1 Fuel filler cap

(5) Slowly add fuel to the fuel tank.

UF2N12E0.book Page 52 Monday, July 4, 2011 3:25 PM

Operation and handling requirements
EJU40290

Fuel tank capacity:
60 L (15.9 US gal, 13.2 Imp.gal)

Engine oil requirements
EJU37134

Engine oil
ECJ00281

NOTICE
Use only 4-stroke engine oil. Usage of 2stroke engine oil could result in severe engine damage.

(6) Stop filling when the fuel level reaches
approximately 50 mm (2 in) from the top
of the fuel tank. Do not overfill the fuel
tank. Because fuel expands when it heats
up, heat from the engine or the sun can
cause fuel to spill out of the fuel tank. Do
not leave the watercraft with a full tank in
direct sunlight.

Recommended engine oil:
YAMALUBE 4W
Recommended engine oil type:
SAE 10W-30, 10W-40, 20W-40, 20W50
Recommended engine oil grade:
API SE,SF,SG,SH,SJ,SL
Checking the engine oil level
EWJ00340

WARNING
Engine oil is extremely hot immediately after the engine is turned off. Coming in contact with or getting any engine oil on your
clothes could result in burns.
ECJ00391

NOTICE
●

●

1 Approximately 50 mm (2 in) from top of the
fuel tank

(7) Wipe up any spilled fuel immediately with
a dry cloth.
(8) Securely install the fuel filler cap by tightening it until it clicks.
(9) Securely install the seat in its original position.

Do not run the engine with too much or
not enough oil in the oil tank, otherwise
the engine could be damaged.
Make sure that debris and water do not
enter the oil tank filler hole. Debris and
water in the engine oil can cause serious
engine damage.

TIP:
●

When checking the engine oil level on land,
the engine must be running while water is
being supplied to the cooling water passages. (See “Flushing the cooling water passeges” on page 78 for information on
supplying water.)

UF2N12E0.book Page 53 Monday, July 4, 2011 3:25 PM

Operation and handling requirements
When checking the engine oil level on water, moor the watercraft so that it will not drift
away.
To check the engine oil level:
(1) With the engine stopped, place the watercraft in a precisely level position on land
or launch the watercraft.
(2) Look in all directions, and then start the
engine. (See page 67 for information on
starting the engine.)
(3) Run the engine at idling speed for 6 minutes or more. Run the engine an additional 5 minutes if the ambient temperature is
20 °C (68 °F) or less.
(4) Stop the engine.
(5) Remove the seat. (See page 45 for seat
removal and installation procedures.)
(6) Loosen the oil tank filler cap and remove
it, and then wipe the attached dipstick
clean.
●

1 Oil tank filler cap/Dipstick

(7) Screw the oil tank filler cap into the filler
hole until it stops. Remove the oil tank filler cap again and make sure that the en-

gine oil level is between the minimum and
maximum level marks.

1 Dipstick
2 Maximum level mark
3 Minimum level mark

(8) If the engine oil level is significantly above
the maximum level mark, consult a
Yamaha dealer. If the engine oil level is
below the minimum level mark, slowly
add engine oil.
(9) Repeat steps 6–8 until the engine oil is at
the proper level.
(10) Securely install the oil tank filler cap and
turn it until it stops.
(11) Securely install the seat in its original position.

UF2N12E0.book Page 54 Monday, July 4, 2011 3:25 PM

Operation and handling requirements
EJU40021

Draining the bilge water
ECJ01301

NOTICE
Do not run the engine at full throttle when
bilge water remains in the engine compartment. The bilge water can splash into the
engine, which can result in severe damage.
EJU40033

Draining the bilge water on land
To drain the bilge water on land:
(1) Loosen the stern drain plugs and remove
them.

maining moisture in the engine compartment with a dry cloth.
(4) Securely install the stern drain plugs by
tightening them until they stop. NOTICE:
Before installing the stern drain plugs,
clean the drain plug threads to remove
any foreign materials, such as dirt or
sand. Otherwise, the stern drain plugs
could be damaged, allowing water to
enter the engine compartment. Make
sure that the stern drain plugs are
tightened securely before launching
the watercraft. Otherwise, water may
flood the engine compartment and
cause the watercraft to submerge.
[ECJ00361]
EJU40534

Draining the bilge water on water

1
1 Stern drain plug

(2) Raise the bow of the watercraft, such as
by placing the watercraft on a slope, to
drain the bilge water from the engine
compartment.
(3) After the bilge water has drained from the
stern drain plug holes, wipe up any re-

A small quantity of bilge water will remain in
the engine compartment even after the bilge
water is drained on water. To completely drain
the bilge water, remove the watercraft from
the water and drain the bilge water on land.
Jet vacuum bilge draining system
While the watercraft is operating, bilge water
in the engine compartment is drawn in by the
vacuum that is generated in the jet pump and
discharged from the watercraft through the jet
thrust nozzle.
To drain the bilge water on water:
Operate the watercraft as straight as possible
and above planing speed for at least 2 minutes. NOTICE: Do not run the engine at full
throttle for at least 1 minute after the engine has been restarted. Bilge water in the
engine compartment can splash into the

UF2N12E0.book Page 55 Monday, July 4, 2011 3:25 PM

Operation and handling requirements
engine, which can result in severe damage. [ECJ00553]

EJU33464

Transporting on a trailer
When transporting the watercraft on a trailer,
secure the tie downs to the trailer through the
bow eye and stern eyes. NOTICE: Do not attach ropes or tie downs to any part of the
watercraft other than the bow eye and
stern eyes to secure the watercraft to the
trailer. Otherwise, the watercraft may be
damaged. Wrap the ropes or tie downs
with towels or rags where they touch the
body of the watercraft to avoid scratches
or damage. VX Deluxe / VX Cruiser: Do not
transport the watercraft with the shift lever
in the reverse position. Otherwise, the reverse gate may hit an obstacle, which
could cause damage. [ECJ00644]

UF2N12E0.book Page 56 Monday, July 4, 2011 3:25 PM

First-time operation
EJU32785

Engine break-in
ECJ00431

NOTICE
Failure to perform the engine break-in
could result in reduced engine life or even
severe engine damage.
The engine break-in is essential to allow the
various components of the engine to wear
and polish themselves to the correct operating clearances. This ensures proper performance and promotes longer component life.
To perform the engine break-in:
(1) Check the engine oil level. (See page 52
for information on checking the engine oil
level.)
(2) Launch the watercraft and start the engine. (See page 67 for information on
starting the engine.)
(3) For the first 5 minutes, operate with the
engine at idling speed.
(4) For the next 30 minutes, operate with the
engine speed below 5000 r/min.
(5) For the next 1 hour, operate with the engine speed below 6500 r/min.
After the engine break-in is complete, the watercraft can be operated normally.

UF2N12E0.book Page 57 Monday, July 4, 2011 3:25 PM

Pre-operation checks
EJU31981

EWJ00411

WARNING
Failure to inspect or maintain the watercraft properly increases the possibility of an accident or damage to the watercraft. Do not operate the watercraft if you find any problem. If a problem cannot be corrected by the procedures provided in this manual, have
the watercraft inspected by a Yamaha dealer.
EJU41232

Pre-operation checklist
Before using this watercraft, be sure to perform the checks in the following checklist.
ITEM

ROUTINE

PAGE

PRE-LAUNCH CHECKS
Engine compartment

Ventilate the engine compartment.
Check inside the engine compartment for damage.

Fuel system

Check the fuel system for leakage.
Check the fuel level in the fuel tank.

Water separator

Check the water separator for water.

Engine unit

Check the exterior of the engine unit for damage.

Engine oil level

Check the engine oil level.

Bilge water

Check the engine compartment for bilge water.

Battery

Check the battery connections and electrolyte level.

Steering system

Check the steering system for proper operation.

Reverse system
(VX Deluxe / VX Cruiser)

Check the reverse system for proper operation.

Throttle lever

Check the throttle lever for proper operation.
Check the throttle lever free play.

Remote control transmitter
(VX Deluxe / VX Cruiser)

Check the remote control transmitter for proper operation.

Engine shut-off cord (lanyard)

Check the engine shut-off cord (lanyard) for damage.

Switches

Check the start switch, engine stop switch, and engine shut-off switch for proper operation.

Storage compartments

Check the storage compartments for damage and
water.

Fire extinguisher holder,
cover, and band

Check the fire extinguisher holder, cover, and band
for damage.

Fire extinguisher

Check the condition of the fire extinguisher.

Safety equipment

Check that safety equipment meeting the applicable
regulations is on board.

Hull and deck

Check the hull and deck for damage.

Jet intake

Check the jet intake for damage and clogging.

Stern drain plugs

Check the stern drain plugs for damage and foreign
material and check that they are securely installed.

UF2N12E0.book Page 58 Monday, July 4, 2011 3:25 PM

Pre-operation checks
ITEM

ROUTINE

PAGE

Hood

Check that the hood is securely closed.

Seat

Check that the seat is securely installed.

Cooling water pilot outlet

Check that water is discharged from the cooling water pilot outlet while the engine is running.

Multifunction information
center

Check the multifunction information center for proper
operation.

Engine idling speed

Check the engine idling speed.

POST-LAUNCH CHECKS

TIP:
To ensure safety and reliability, pre-operation checks should be made each time the watercraft
is used.

UF2N12E0.book Page 59 Monday, July 4, 2011 3:25 PM

Pre-operation checks
EJU32281

Pre-operation check points
EJU40545

Pre-launch checks
Perform the pre-launch checks in the pre-operation checklist while the watercraft is on
land.
To perform the pre-launch checks:
(1) Remove the seat. (See page 45 for seat
removal and installation procedures.)
(2) Perform the checks and make sure that
there are no malfunctioning items or other problems.
(3) After completing these checks, securely
install the seat in its original position.
EJU32333

Engine compartment check
EWJ00461

WARNING
Failure to ventilate the engine compartment could result in a fire or explosion. Do
not start the engine if there is a fuel leak.
Ventilate the engine compartment. Leave the
engine compartment open for a few minutes
to allow any fuel vapors to escape.
Make sure that there is no damage inside the
engine compartment.

●

If any fuel leakage is found, the fuel system must be repaired by a qualified mechanic. Improper repairs can make the
watercraft unsafe to operate.

Make sure that there is no damage, leakage,
or other problem in the fuel system.
Check:
● Fuel filler cap and seal for damage
● Fuel tank for damage and leakage
● Fuel hoses and joints for damage and leakage
● Fuel tank breather hose for damage and
leakage
EJU36874

Fuel level check
Check the fuel level in the fuel tank.
Add fuel if necessary. (See page 51 for information on filling the fuel tank.)
EJU32423

Water separator check
Make sure that no water has collected in the
water separator. If water has collected in the
water separator, drain it. (See page 35 for information on draining the water separator.)

1 Water separator
EJU40181

EJU34214

Fuel system checks
EWJ00381

WARNING
Leaking fuel can result in fire or explosion.
● Check for fuel leakage regularly.

Engine unit check
Check the exterior of the engine unit for damage or other problem.
EJU41560

Engine oil level check
Make sure that the engine oil level is between
the minimum and maximum level marks on

UF2N12E0.book Page 60 Monday, July 4, 2011 3:25 PM

Pre-operation checks
the dipstick attached to the oil tank filler cap.
(See page 52 for information on checking the
engine oil level.)

aged, obstructed, or not connected properly. [EWJ00451]

1
3

1 Negative (–) battery terminal: Black lead
2 Positive (+) battery terminal: Red lead
3 Breather hose

1 Oil tank filler cap/Dipstick

Make sure that the electrolyte level is between the minimum and maximum level
marks. WARNING! Never operate the watercraft if the battery does not have sufficient power to start the engine or if it
shows any other signs of decreased power. Loss of battery power may leave you
stranded. [EWJ01240]

1 Dipstick
2 Maximum level mark
3 Minimum level mark
EJU32455

Bilge water check
Make sure that no bilge water has collected in
the engine compartment. If bilge water has
collected in the engine compartment, drain it.
(See page 54 for information on draining the
bilge water.)
EJU32484

Battery checks
Make sure that the battery terminals and
breather hose are not damaged and that the
battery leads and breather hose are connected properly. WARNING! Fire or explosion
could result if the breather hose is dam-

1 Maximum level mark
2 Minimum level mark

Make sure that the battery is securely held in
place.
EJU32613

Steering system checks
Turn the handlebars to the right and left several times to make sure that operation is
smooth and unrestricted throughout the

UF2N12E0.book Page 61 Monday, July 4, 2011 3:25 PM

Pre-operation checks
whole range, and that the free play is not excessive.

right and left fully turned positions of the jet
thrust nozzle.

Turn the handlebars as far as possible to the
right and left to make sure that the jet thrust
nozzle moves as the handlebars are turned,
and that there is no difference between the

Difference between fully turned positions
of jet thrust nozzle (distances A and B):
Maximum 5 mm (0.20 in)
EJU32634

Reverse system checks (VX Deluxe /
VX Cruiser)
EWJ00031

WARNING
Do not touch the reverse gate while the
shift lever is being operated, otherwise
you could be pinched.

UF2N12E0.book Page 62 Monday, July 4, 2011 3:25 PM

Pre-operation checks
Operate the shift lever several times to make
sure that operation is smooth throughout the
whole range. Also, make sure that the reverse
gate moves up and down according to the operation of the shift lever and that the gate
makes contact with the stoppers. (See page
37 for reverse system operation.)

throttle lever returns automatically to its fully
closed (idle) position when released.

Make sure that there is the proper amount of
throttle lever free play when the throttle lever
is in the fully closed (idle) position.

1
1 Throttle lever free play
1 Stopper

Throttle lever free play:
4.0–7.0 mm (0.16–0.28 in)

EJU32594

Throttle lever checks
Operate the throttle lever several times to
make sure that operation is smooth throughout the whole range. Also, make sure that the

EJU40112

Remote control transmitter check
(VX Deluxe / VX Cruiser)
Make sure that the remote control transmitter
operates properly. (See page 32 for Yamaha
Security System setting procedures and page
38 for Low RPM Mode activation procedures.)
EJU32663

Engine shut-off cord (lanyard) check
Make sure that the engine shut-off cord (lanyard) is not damaged. If the cord is damaged,
replace it. WARNING! Never try to repair
the engine shut-off cord (lanyard) or tie it

UF2N12E0.book Page 63 Monday, July 4, 2011 3:25 PM

Pre-operation checks
together. The engine shut-off cord (lanyard) may not pull free when the operator
falls off, allowing the watercraft to continue to run and cause an accident. [EWJ01220]

EJU32675

Switch checks
ECJ01310

To check the operation of the switches:
(1) VX Deluxe / VX Cruiser: If the lock mode
is selected for the Yamaha Security System setting, select the unlock mode. (See
page 32 for Yamaha Security System
setting procedures.)
(2) Push the start switch to make sure that
the engine starts.
(3) As soon as the engine starts running,
push the engine stop switch to make sure
that the engine stops immediately.
(4) Restart the engine, and then pull the engine shut-off cord (lanyard) to remove the
clip from the engine shut-off switch to
make sure that the engine stops immediately.
EJU40101

NOTICE
Do not run the engine over 4000 r/min on
land. Also, do not run the engine for more
than 15 seconds without supplying water,
otherwise the engine could overheat.

Storage compartment checks
Make sure that the storage compartments are
not damaged and that water has not collected
in the compartments. (See page 47 for information on the storage compartments.)
EJU41081

Check the start switch, the engine stop
switch, and the engine shut-off switch for
proper operation. (See pages 33 to 33 for information on operating each switch.)

1
2
3
4
5

Engine shut-off switch
Clip
Start switch
Engine stop switch
Engine shut-off cord (lanyard)

Fire extinguisher holder, cover, and band
checks
Make sure that the fire extinguisher holder,
cover, and band are not damaged and that
the cover is securely held in place using the
band. (See page 49 for information on the fire
extinguisher holder, cover, and band.)

UF2N12E0.book Page 64 Monday, July 4, 2011 3:25 PM

Pre-operation checks
EJU32533

EJU32475

Fire extinguisher check
Check that there is a full fire extinguisher on
board.

Stern drain plug checks
Loosen the stern drain plugs and remove
them, and then make sure that the plugs are
not damaged and that there is no foreign material on the threads. NOTICE: Before installing the stern drain plugs, clean the
drain plug threads to remove any foreign
materials, such as dirt or sand. Otherwise,
the stern drain plugs could be damaged,
allowing water to enter the engine compartment. Make sure that the stern drain
plugs are tightened securely before
launching the watercraft. Otherwise, water
may flood the engine compartment and
cause the watercraft to submerge. [ECJ00361]
Securely install the stern drain plugs by tightening them until they stop.

To check the fire extinguisher, see the instructions supplied by the fire extinguisher manufacturer. Always keep the fire extinguisher
secured in the holder with its cover in place.
Always carry a fire extinguisher on board. A
fire extinguisher is not standard equipment
with this watercraft. If you do not have one,
contact a Yamaha dealer or a fire extinguisher
dealer to obtain one meeting the proper specifications.
Fire extinguisher:
Classification:
B-1
Capacity:
2 lb or more

1
1 Stern drain plug

EJU40121

Safety equipment check
Check that safety equipment meeting the applicable regulations is on board.
EJU32352

Hull and deck check
Check the hull and deck for damage or other
problem.
EJU32656

Jet intake checks
Make sure that the jet intake is not damaged
or clogged with weeds or debris. If the jet intake is clogged, clean it. (See page 91 for information on the jet intake.)

UF2N12E0.book Page 65 Monday, July 4, 2011 3:25 PM

Pre-operation checks
EJU41440

EJU32713

Hood check
Push down on the rear of the hood and make
sure that it is securely closed.

Multifunction information center check
Make sure that the multifunction information
center operates properly. (See page 40 for information on proper operation of the multifunction information center.)

EJU40144

Post-launch checks
Perform the post-launch checks in the pre-operation checklist while the watercraft is in the
water and the engine is running.
To perform the post-launch checks:
(1) Launch the watercraft. (See page 67 for
information on launching the watercraft.)
(2) Perform the checks and make sure that
there are no malfunctioning items or other problems.
EJU40552

Cooling water pilot outlet check
Make sure that water is discharged from the
cooling water pilot outlet while the engine is
running. (See page 35 for information on the
cooling water pilot outlet.)

EJU40171

Engine idling speed check
Start the engine and warm it up. Use the tachometer in the multifunction information center to make sure that the engine idling speed
is not significantly above or below the specified range.
Engine idling speed:
1650 ±50 r/min

UF2N12E0.book Page 66 Monday, July 4, 2011 3:25 PM

Operation
EJU32902

Operating your watercraft
EWJ00510

WARNING
Before operating your watercraft, become
familiar with all of the controls. Consult a
Yamaha dealer about any control or function that you do not fully understand. Failure to understand how the controls work
could cause an accident or prevent you
from avoiding an accident.
EJU32954

Getting to know your watercraft
Operating your watercraft requires skills acquired through practice over a period of time.
Take the time to learn the basic techniques
well before attempting more difficult maneuvers.
Operating your new watercraft can be a very
enjoyable activity, providing you with hours of
pleasure. However, it is essential to familiarize yourself with the operation of the watercraft to achieve the skill level necessary to
enjoy riding safely.
Before operating this watercraft, read this
owner’s/operator’s manual, the Riding Practice Guide, the Riding Instruction card, and all
labels on the watercraft. Pay particular attention to the safety information beginning on
page 10. Also, watch the Basic Orientation
Video provided with your watercraft. These
materials should give you an understanding of
the watercraft and its operation.
Remember: This watercraft is designed to
carry the operator and up to 2 passengers.
Never exceed the maximum load limit or allow
more than 3 persons (or 2 persons if a waterskier is being pulled) to ride the watercraft at
any time.

Maximum load:
240 kg (530 lb)
Load is the total weight of cargo, operator, and passengers.
EJU32995

Learning to operate your watercraft
Before operating the watercraft, always perform the pre-operation checks listed on page
57. The short time spent checking the watercraft will reward you with added safety and reliability.
Check state and local laws before operating
your watercraft.
Operate defensively at safe speeds and keep
a safe distance away from people, objects,
and other watercraft. Select a wide area to
learn in, where there is good visibility and light
boat traffic.

Use the buddy system—operate with someone nearby. Scan constantly for people, objects, and other watercraft. Be alert for
conditions that limit your visibility or block your
vision of others.
You should grip the handlebars firmly and
keep both feet on the floor of the footwell. Do
not attempt to ride with passengers until your
operating skills are fully developed.

UF2N12E0.book Page 67 Monday, July 4, 2011 3:25 PM

Operation
EJU40210

EJU36345

Riding position

Starting the engine on water

Operator riding position
The operator should grip the handlebars firmly with both hands and sit astride the seat with
both feet on the floor of the footwell.

EWJ01530

Passenger riding position
The passenger(s) should hold on firmly, either
to the person in front of them or to the handgrip provided, and sit astride the seat with
their feet on the floor of the footwell. Never allow a passenger to ride in front of the operator. (See page 18 for information on the riding
position when pulling a water-skier.)

WARNING
Do not apply throttle when anyone is at the
rear of the watercraft. Turn the engine off
or keep it at idle. Water and debris exiting
the jet thrust nozzle can cause severe injury.
To start the engine:
(1) VX Deluxe / VX Cruiser: If the lock mode
is selected for the Yamaha Security System setting, select the unlock mode. (See
page 32 for Yamaha Security System
setting procedures.)
(2) Move the watercraft to an area that is free
from weeds and debris, and has a water
depth of at least 60 cm (2 ft) from the bottom of the watercraft. NOTICE: Never
run the engine in water that is less
than 60 cm (2 ft) deep from the bottom
of the watercraft, otherwise pebbles or
sand could be sucked into the jet intake, causing impeller damage and engine overheating. [ECJ00472]

EJU32802

Launching the watercraft
When launching the watercraft, make sure
that there are no obstacles around you.
If the watercraft is launched from a trailer,
someone should make sure that waves do not
push the watercraft into the trailer.

(3) Attach the engine shut-off cord (lanyard)
to your left wrist, and then attach the clip
to the engine shut-off switch. (See page
33 for information on operating the engine shut-off switch.) WARNING! Check
that the engine shut-off cord (lanyard)

UF2N12E0.book Page 68 Monday, July 4, 2011 3:25 PM

Operation
is attached correctly. If the engine
shut-off cord (lanyard) is not attached
correctly, it may not pull free when the
operator falls off, allowing the watercraft to continue to run and cause an
accident. [EWJ00581]

avoid. A collision could result in severe injury or death. [EWJ00601]

EJU32872

1 Clip
2 Engine shut-off switch
3 Engine shut-off cord (lanyard)

Leaving the watercraft
If leaving the watercraft, remove the clip from
the engine shut-off switch to prevent accidental starting or unauthorized operation by children or others.

(4) With the throttle lever released, push the
start switch (green button) to start the engine. (See page 33 for information on operating the start switch.)
ST
OP

STAR
T

EJU41572

Operating the watercraft
VX Sport:
When the engine is running, the watercraft will
move forward at trolling speed even if the
EJU32862

Stopping the engine
Release the throttle lever, and then push the
engine stop switch (red button) to stop the engine. WARNING! You need throttle to steer.
Shutting the engine off can cause you to
hit an obstacle you are attempting to

UF2N12E0.book Page 69 Monday, July 4, 2011 3:25 PM

Operation
throttle lever is in the fully closed (idle) position.

EJU33254

Turning the watercraft
EWJ00771

WARNING
●

●

VX Deluxe / VX Cruiser:
When the shift lever is in the forward position
and the engine is running, the watercraft will
move forward. The watercraft will move forward at trolling speed even if the throttle lever
is in the fully closed (idle) position. (See page
37 for information on operating the shift lever.)

2
1 Shift lever
2 Forward position

Do not release the throttle lever when
trying to steer away from objects—you
need throttle to steer. A collision could
result in severe injury or death.
When operating at higher speeds, make
gradual turns or slow down before turning. Sharp high-speed turns may cause
the watercraft to slide sideways or spin,
throwing the operator and passenger(s)
overboard, which could cause an injury.

Steering control depends on the combination
of handlebar position and the amount of throttle.
Water sucked in through the intake grate is
pressurized by the impeller in the jet pump. As
the pressurized water is expelled from the
pump through the jet thrust nozzle, it creates
thrust to move and steer the watercraft. The
higher the engine speed, the more thrust produced.
The amount of jet thrust, in addition to the position of the handlebars, determines how
sharply you turn.
A. More throttle produces higher thrust, so
the watercraft will turn more sharply.

UF2N12E0.book Page 70 Monday, July 4, 2011 3:25 PM

Operation
B. Less throttle produces lower thrust, so
the watercraft will turn more gradually.

C. Releasing the throttle lever completely
produces only minimum thrust. If you are
traveling at speeds above trolling, you will
have rapidly decreasing ability to steer
without throttle. You may still have some
turning ability immediately after releasing
the throttle lever, but once the engine
slows down, the watercraft will no longer
respond to handlebar input until you apply throttle again or you reach trolling
speed.
At trolling speed, the watercraft can be
turned gradually by handlebar position
alone using just the amount of thrust
available at idle.

D. If the engine is stopped while riding, there
is no thrust. The watercraft will go straight
even though the handlebars are turned.

You need throttle to steer.
This model is equipped with the Yamaha Engine Management System (YEMS) that includes an off-throttle steering (OTS) system.
It will activate at planing speeds should you
attempt to steer the watercraft after releasing
the throttle lever (see condition C above).
The OTS system assists in turning by continuing to supply some thrust while the watercraft
is decelerating, but you can turn more sharply
if you apply throttle while turning the handlebars. The OTS system does not function below planing speeds or when the engine is off.
Once the engine slows down, the watercraft
will no longer turn in response to handlebar input until you apply throttle again or you reach
trolling speed.
EJU33294

Stopping the watercraft
The watercraft is not equipped with a separate braking system. It is stopped by water resistance when the throttle lever is released.
From full speed, the watercraft comes to a
complete stop in approximately 100 m (330 ft)
after the throttle lever is released or the engine is stopped, although this distance will
vary depending on many factors, including
gross weight, water surface conditions, and
wind direction. The watercraft slows down as

UF2N12E0.book Page 71 Monday, July 4, 2011 3:25 PM

Operation
soon as the throttle lever is released, but will
coast for a distance before fully stopping. If
you are not sure you can stop in time before
hitting an obstacle, apply throttle and turn in
another direction.

(See page 37 for information on the reverse
system.)

2
1 Shift lever
2 Reverse position

EWJ00744

WARNING
●
●

●

Allow adequate stopping distance.
Take early action to avoid collisions. Remember, watercraft and other boats do
not have brakes.
Operate defensively at safe speeds and
keep a safe distance away from people,
objects, and other watercraft to give you
time to stop.
Do not shut the engine off when slowing
down in case you need engine power to
steer away from a boat or other obstacle
that comes into your path.
VX Deluxe / VX Cruiser: Do not use the
reverse function to slow down or stop
the watercraft as it could cause you to
lose control, be ejected, or impact the
handlebars.

EJU41580

Operating the watercraft in reverse
(VX Deluxe / VX Cruiser)
Pull the shift lever rearward to the reverse position. The watercraft will move in reverse.

Make sure that there are no obstacles or people behind you before shifting into reverse.
EJU36086

Boarding the watercraft
EWJ01111

WARNING
Be sure the operator and any passengers
have practiced boarding from the water
while still close to shore before riding. A
person who has made many unsuccessful
attempts to get back on the watercraft may
become fatigued and suffer from exposure, increasing the risk of injury and
drowning.
Board the watercraft in water free from weeds
and debris and at least 60 cm (2 ft) deep from
the bottom of the watercraft. NOTICE: Never

UF2N12E0.book Page 72 Monday, July 4, 2011 3:25 PM

Operation
run the engine in water that is less than 60
cm (2 ft) deep from the bottom of the watercraft, otherwise pebbles or sand could
be sucked into the jet intake, causing impeller damage and engine overheating.

(2) Pull yourself up to a kneeling position on
the boarding platform, and then move to
the seat and sit astride.

[ECJ00472]

60 cm (2 ft)

TIP:
VX Cruiser: This watercraft is equipped with a
reboarding step, which can be lowered and
used to assist in reboarding. (See page 46 for
information on operating the reboarding step.)

(3) Attach the engine shut-off cord (lanyard)
to your left wrist, and then attach the clip
to the engine shut-off switch.
(4) Grip the handlebars with both hands and
place both feet on the floor of the footwell.

EJU36353

Boarding alone
(1) From the rear of the watercraft, place
both hands on the boarding platform, pull
yourself up, and then grasp the handgrip
with one hand.
(5) Look in all directions, start the engine,
and then start off slowly.
EJU33169

Boarding with passenger(s)
EWJ00660

WARNING
Severe internal injuries can occur if water
is forced into body cavities as a result of
being near the jet thrust nozzle. Do not apply throttle until the passengers are seated
with their feet on the floor of the footwell
and are securely holding on to the person

UF2N12E0.book Page 73 Monday, July 4, 2011 3:25 PM

Operation
in front of them or to the handgrip provided.

their feet on the floor of the footwell, and
securely hold on to the operator.

The heavier the total weight of the operator
and passenger(s), the more difficult it will be
to balance the watercraft. Do not operate the
watercraft when the total weight exceeds 240
kg (530 lb) including any cargo.
To board at a standstill:
(1) Board as noted in the previous section
“Boarding alone”.
(6) Have the second passenger follow the
same procedure. When the second passenger is boarding, try to balance the watercraft together with the first passenger.

(2) Attach the engine shut-off cord (lanyard)
to your left wrist, and then attach the clip
to the engine shut-off switch.
(3) Grip the handlebars with both hands and
place both feet on the floor of the footwell.
(4) Have the first passenger move to the rear
of the watercraft.

(5) Have the first passenger board using the
same procedure as the operator, place

(7) Make sure that the passenger(s) have
their feet on the floor of the footwell and
are securely holding on to the person in
front of them or to the handgrip provided.

UF2N12E0.book Page 74 Monday, July 4, 2011 3:25 PM

Operation
(8) Look in all directions, start the engine,
and then start off slowly.
To board when it is difficult to balance at a
standstill:
(1) Have the passenger(s) steady the watercraft, and then board as noted in the previous section “Boarding alone”.

(2) Grip the handlebars with both hands,
place both feet on the floor of the footwell,
and balance there.
(3) Have the first passenger board using the
same procedure as the operator, place
their feet on the floor of the footwell, securely hold on to the operator, and balance there.
(4) Attach the engine shut-off cord (lanyard)
to your left wrist, and then attach the clip
to the engine shut-off switch.
(5) Look in all directions, and then start the
engine and operate at trolling speed.
(6) Have the second passenger pull themselves up onto the boarding platform into
a kneeling position and balance there.
Look in all directions, and then gradually
accelerate. Then, have the second pas-

senger crawl onto the seat while maintaining their balance.

(7) Have the second passenger sit astride
the seat, place their feet on the floor of
the footwell, securely hold on to the person in front of them or to the handgrip
provided, and balance there.
(8) Make sure that the passenger(s) have
their feet on the floor of the footwell and
are securely holding on to the person in
front of them or to the handgrip provided,
and then gradually increase the speed to
balance the watercraft.

EJU33082

Starting off
EWJ00711

WARNING
To avoid collisions:
● Scan constantly for people, objects, and
other watercraft. Be alert for conditions
that limit your visibility or block your vision of others.

UF2N12E0.book Page 75 Monday, July 4, 2011 3:25 PM

Operation
●

●

ECJ01340

NOTICE
Never run the engine in water that is less
than 60 cm (2 ft) deep from the bottom of
the watercraft, otherwise pebbles or sand
could be sucked into the jet intake, causing impeller damage and engine overheating.

(2) Attach the engine shut-off cord (lanyard)
to your left wrist, and then attach the clip
to the engine shut-off switch.
(3) Look in all directions, start the engine,
and then start off slowly.
VX Deluxe / VX Cruiser:
(1) Launch the watercraft, and then move the
shift lever to the reverse position. (See
page 37 for information on the reverse
system.)
(2) Attach the engine shut-off cord (lanyard)
to your left wrist, and then attach the clip
to the engine shut-off switch.
(3) Look in all directions, start the engine,
and then start off slowly.
EJU33113

Boarding and starting off from a dock
(1) Board the watercraft from the side.
(2) Attach the engine shut-off cord (lanyard)
to your left wrist, and then attach the clip
to the engine shut-off switch.
(3) Push the watercraft away from the dock,
grip the handlebars with both hands, and
place both feet on the floor of the footwell.

(4) Look in all directions, start the engine,
and then start off slowly.
EJU40592

Starting off from a trailer
VX Sport:
(1) Launch the watercraft, and then turn it
around so that the bow faces the direction you wish to go.

EJU33235

Capsized watercraft
EWJ00671

WARNING
Improper uprighting can cause injury.

UF2N12E0.book Page 76 Monday, July 4, 2011 3:25 PM

Operation
●

●

Be sure to shut the engine off by pulling
on the engine shut-off cord (lanyard) to
remove the clip from the engine shut-off
switch.
Do not put your hands in the intake
grate.

If the watercraft capsizes, turn it over immediately.
To upright the watercraft:
(1) Remove the clip from the engine shut-off
switch.
(2) Swim to the rear of the watercraft. Turn
the watercraft over clockwise by pulling
on the ride plate with your left hand while
pushing down on the gunwale with your
right hand or foot.
If the port (left) side of the capsized watercraft is tilting up, push down on the
gunwale so that the port (left) side is
down before turning the watercraft clockwise. NOTICE: Do not turn the watercraft
over
counterclockwise,
otherwise water can enter the engine,

which can result in severe damage.
[ECJ00541]

(3) Start the engine and operate the watercraft at planing speed to drain the bilge
water from the engine compartment.
(See page 54 for information on draining
the bilge water. If the engine does not
start, see “Towing the watercraft” on
page 94 or “Submerged watercraft” on
page 94.) NOTICE: Do not run the engine at full throttle for at least 1 minute
after the engine has been restarted.
Bilge water in the engine compartment can splash into the engine,
which can result in severe damage.
[ECJ00553]
EJU35962

Beaching and docking the watercraft
To beach the watercraft:
(1) Make sure that there are no boats, swimmers, or obstacles near the beach.

UF2N12E0.book Page 77 Monday, July 4, 2011 3:25 PM

Operation
(2) Release the throttle lever to reduce
speed about 100 m (330 ft) before you
reach the intended beaching area.
(3) Slowly approach the beach and stop the
engine just before reaching land.
WARNING! You need throttle to steer.
Shutting the engine off can cause you
to hit an obstacle you are attempting
to avoid. A collision could result in severe injury or death. [EWJ00601] NOTICE:
Never run the engine in water that is
less than 60 cm (2 ft) deep from the
bottom of the watercraft, otherwise
pebbles or sand could be sucked into
the jet intake, causing impeller damage and engine overheating. [ECJ00472]
(4) Get off the watercraft and pull it up on the
beach.
To dock the watercraft:
(1) Make sure that there are no boats, swimmers, or obstacles near the dock.
(2) Release the throttle lever to reduce
speed about 100 m (330 ft) away from the
dock.
(3) Slowly approach the dock and stop the
engine just before coming alongside it.
WARNING! You need throttle to steer.
Shutting the engine off can cause you
to hit an obstacle you are attempting
to avoid. A collision could result in severe injury or death. [EWJ00601]
(4) Come alongside the dock and get off the
watercraft.
EJU37193

Operating in weeded areas
Always avoid using your watercraft in areas
where weed growth is thick. If operating in
weeded areas is unavoidable, alternately
squeeze the throttle lever and relax your grip
on the throttle lever to vary the engine speed.
Weeds tend to become clogged more when
operating at a steady speed and at trolling

speed. If weeds may have clogged the intake
area, clean the jet intake. (See page 91 for information on the jet intake.)
EJU40241

After removing the watercraft from the
water
ECJ01310

NOTICE
Do not run the engine over 4000 r/min on
land. Also, do not run the engine for more
than 15 seconds without supplying water,
otherwise the engine could overheat.
After operating and removing the watercraft
from the water, promptly discharge the remaining water from the cooling water passages.
To discharge water from the cooling water
passages:
(1) Make sure that the area around the watercraft is clear, and then start the engine.
(2) Discharge the remaining water out of the
cooling water passages by alternately
squeezing and releasing the throttle lever
quickly for 10 to 15 seconds.
(3) Stop the engine.

UF2N12E0.book Page 78 Monday, July 4, 2011 3:25 PM

Care and storage
EJU37145

Post-operation care
EWJ00330

(3) Connect the garden hose adapter to a
garden hose.

WARNING
Always place the watercraft upright in a
horizontal position when storing it, otherwise fuel could leak out into the engine or
engine compartment, which could create a
fire hazard.
After using the watercraft, always take it out of
the water, clean it, and store it. Leaving the
watercraft in the water for extended periods
will accelerate the rate of normal deterioration
of the jet pump and hull. Marine organisms
and corrosion are some of the conditions that
can shorten the life of many watercraft components.

1 Garden hose adapter

(4) Loosen the flushing hose connector cap
and remove it. Insert the garden hose
adapter into the flushing hose connector
and turn it until it is securely connected.

EJU33547

Flushing the cooling water passages

ECJ01310

NOTICE
Do not run the engine over 4000 r/min on
land. Also, do not run the engine for more
than 15 seconds without supplying water,
otherwise the engine could overheat.
Flush the cooling water passages to prevent
them from clogging with salt, sand, or dirt.
(1) Place the watercraft in a horizontal position.
(2) Remove the seat. (See page 45 for seat
removal and installation procedures.)

2
3

1 Garden hose adapter
2 Flushing hose connector
3 Flushing hose connector cap

(5) Connect the garden hose to a water tap.
(6) Make sure that the area around the watercraft is clear, and then start the engine.
Immediately after the engine starts, fully
turn the water supply on so that water

UF2N12E0.book Page 79 Monday, July 4, 2011 3:25 PM

Care and storage
flows out continually from the jet thrust
nozzle.

(7) Run the engine at idling speed for about
3 minutes watching the engine condition.
If the engine stops while flushing, turn the
water supply off immediately and perform
the procedure again from step 6.
NOTICE: Do not supply water to the
cooling water passages when the engine is not running. The water could
flow back through the muffler into the
engine, causing severe engine damage. [ECJ00122]
(8) Turn the water supply off.
(9) Discharge the remaining water out of the
cooling water passages by alternately
squeezing and releasing the throttle lever
quickly for 10 to 15 seconds.
(10) Stop the engine.
(11) Remove the garden hose adapter, and
then securely install the flushing hose
connector cap by tightening it until it
stops.
(12) Securely install the seat in its original position.
EJU41690

Cleaning the watercraft
(1) Remove the seat. (See page 45 for seat
removal and installation procedures.)
(2) If the watercraft will be stored for a week
or more, rustproof the internal engine
components to help prevent corrosion.

(See page 83 for information on rustproofing the internal engine components.)
(3) Rinse the engine and engine compartment with a small amount of water.
NOTICE: Do not use high-pressure
water when rinsing the engine or engine compartment as severe engine
damage could result. [ECJ00571]
(4) Drain the water from the engine compartment. (See page 54 for information on
draining the bilge water.)
(5) Wipe the engine and engine compartment with a dry cloth.
(6) Wash down the hull, deck, and jet pump
with fresh water.
(7) Wipe the hull, deck, and jet pump with a
dry cloth.
(8) Wipe all vinyl and rubber components,
such as the seat and engine compartment seals, with a vinyl protectant such
as Yamaha Protectant.
(9) To minimize corrosion, spray metallic
parts of the hull, deck, and engine with a
rust inhibitor such as Yamaha Silicone
Protectant and Lubricant.
(10) Allow the engine compartment to air dry
completely before installing the seat.
(11) Securely install the seat in its original position.
EJU41630

Battery care
If the watercraft will not be used for more than
a month, remove the battery from the watercraft, check it, and then store it in a cool, dry
place.
EWJ00791

WARNING
Battery electrolyte is poisonous and dangerous, causing severe burns, etc. Electrolyte contains sulfuric acid. Avoid
contact with skin, eyes, or clothing.

UF2N12E0.book Page 80 Monday, July 4, 2011 3:25 PM

Care and storage
Antidotes
External: Flush with water.
Internal: Drink large quantities of water or
milk. Follow with milk of magnesia, beaten
egg, or vegetable oil. Call a physician immediately.
Eyes: Flush with water for 15 minutes and
get prompt medical attention.
Batteries produce explosive gases. Keep
sparks, flames, cigarettes, etc., well away.
If using or charging the battery in an enclosed space, make sure that it is well ventilated. Always shield your eyes when
working near batteries.
Keep out of the reach of children.
To remove the battery:
(1) Disconnect the negative (–) battery lead.
(2) Disconnect the positive (+) battery lead.
(3) Disconnect the breather hose.
(4) Unhook the battery bands, and then remove the battery from the watercraft.

1
4
1
2
3
4

Negative (–) battery terminal: Black lead
Battery band
Positive (+) battery terminal: Red lead
Breather hose

Make sure that the breather hose is not
clogged or damaged.
Checking the electrolyte level
Make sure that the electrolyte level is between the maximum and minimum level
marks.
If the electrolyte level is low, add distilled water to raise it to the specified level. NOTICE:
Use only distilled water for replenishing
the battery, otherwise battery life could be
shortened. [ECJ00241]
●

1 Maximum level mark
2 Minimum level mark

If distilled water was added, check the battery
voltage.
It is recommended to have a Yamaha dealer
check the battery voltage and charge the battery. If you charge the battery yourself, be
sure to read and follow the instructions provided with the battery tester and charger you
use. NOTICE: Do not attempt to charge a
battery hastily. Battery life could be shortened. [ECJ00251]

Checking the battery
Make sure that the battery case is not damaged.
● Make sure that the battery terminals are not
corroded or damaged.
●

UF2N12E0.book Page 81 Monday, July 4, 2011 3:25 PM

Care and storage
Checking the battery bands
Make sure that the battery bands are not
damaged.

1 Battery band

To store the battery:
(1) Clean the battery case using fresh water.
(2) If the battery terminals are dirty or corroded, clean them using a wire brush.

1 Battery terminal

(3) Apply YAMALUBE MARINE GREASE to
the battery terminals.
Recommended water-resistant grease:
YAMALUBE MARINE GREASE
(4) Store the battery in a cool, dry place.
NOTICE: Storing the battery in an uncharged condition can cause permanent battery damage. Check the
battery periodically. [ECJ00102]

To install the battery:
(1) Place the battery in the battery compartment and hook the battery bands onto the
holders.
(2) Connect the positive (+) battery lead (red)
to the positive (+) battery terminal.
NOTICE: Reversal of the battery leads
will damage the electrical parts. [ECJ00261]
(3) Connect the negative (–) battery lead
(black) to the negative (–) battery terminal.
(4) Connect the breather hose to the battery.
WARNING! Fire or explosion could result if the breather hose is damaged,
obstructed, or not connected properly. [EWJ00451]
(5) Make sure that the battery is securely
held in place.

UF2N12E0.book Page 82 Monday, July 4, 2011 3:25 PM

Care and storage
EJU33492

Recommended water-resistant grease:
YAMALUBE MARINE GREASE

Long-term storage
EWJ00330

WARNING
Always place the watercraft upright in a
horizontal position when storing it, otherwise fuel could leak out into the engine or
engine compartment, which could create a
fire hazard.
Storage for long periods of time, such as winter storage, requires preventive maintenance
to ensure against deterioration. It is advisable
to have the watercraft serviced by a Yamaha
dealer prior to storage.
However, the following procedures can be
performed easily by the owner.

●

Throttle cable (throttle lever end)

●

Steering cable (jet thrust nozzle end)

●

VX Deluxe / VX Cruiser:
Shift cable (shift lever end)

EJU40252

Cleaning
(1) Flush the cooling water passages. (See
page 78 for information on flushing the
cooling water passages.)

TIP:
If you will be storing the watercraft for a prolonged period, such as winter storage, top off
the fuel tank with fresh gasoline and add one
ounce of Yamaha Fuel Stabilizer and Conditioner to each gallon of fuel in the fuel tank before starting the engine.
(2) Clean the watercraft. (See page 79 for information on cleaning the watercraft.)
Wax the hull with a non-abrasive wax
such as Yamaha Silicone Wax.
EJU40624

Lubrication
Use a Yamaha Power Cable Luber and spray
Yamaha Lube-Zall between the inner and outer cables to lubricate the cables and purge out
any dirt and moisture.
To keep moving parts sliding or rotating
smoothly, lubricate them with water-resistant
grease.

UF2N12E0.book Page 83 Monday, July 4, 2011 3:25 PM

Care and storage
●

VX Deluxe / VX Cruiser:
Shift cable (reverse gate end)

take opening for 3 seconds. WARNING!
Do not spray flammable rust inhibitor
products on engine surfaces while the
engine is hot. The sprayed substance
or propellants could catch fire. [EWJ00261]

EJU41660

Rustproofing
Rustproofing the hull, deck, and engine
Spray metallic parts of the hull, deck, and engine with a rust inhibitor such as Yamaha Silicone Protectant and Lubricant.
Rustproofing the internal engine components
Rustproof the internal engine components
with a rust inhibitor such as Yamaha Stor-Rite
Engine Fogging Oil.
To rustproof the internal engine components:
(1) Remove the seat. (See page 45 for seat
removal and installation procedures.)
(2) Loosen the clamp screw and disconnect
the air intake duct.

1 Air intake duct
2 Clamp screw

(3) Spray a rust inhibitor such as Yamaha
Stor-Rite Engine Fogging Oil into the in-

1 Intake opening

(4) Connect the air intake duct and securely
tighten the clamp screw.
(5) Make sure that the area around the watercraft is clear, and then start the engine
in a well-ventilated area and let it run at
idle for 15 seconds. (See page 33 for information on starting the engine.)
(6) Stop the engine.
(7) Securely install the seat in its original position.

UF2N12E0.book Page 84 Monday, July 4, 2011 3:25 PM

Maintenance
EJU33757

EJU33802

Maintenance
Periodic checks and lubrication will keep your
watercraft in the safest and most efficient condition possible. Therefore, make sure to carry
out the periodic maintenance. Safety is an obligation of the watercraft owner. Proper maintenance must be carried out to keep the
exhaust emission and sound levels within the
regulated limits. The most important points of
watercraft inspection and lubrication are explained on the following pages.
See a Yamaha dealer for genuine Yamaha replacement parts and optional accessories designed for your watercraft.
Remember, failures that are the result of the
installation of parts or accessories which are
not qualitatively equivalent to genuine
Yamaha parts are not covered by the limited
warranty.
Maintenance, replacement, or repair of the
emission control devices and system may
be performed by any marine SI engine repair establishment or individual. Warranty
repair, however, must be performed at an
authorized Yamaha marine dealership.

Tool kit
A tool kit is included with this watercraft. Place
the tool kit in a waterproof bag and always
carry it with you whenever you use the watercraft.

1
2
3
4
5
6

Tool bag
Screwdriver
Garden hose adapter
10/12 mm box wrench
Pliers
Open-end wrench

EWJ00311

WARNING
Be sure to turn off the engine when you
perform maintenance unless otherwise
specified. If you are not familiar with machine servicing, this work should be done
by a Yamaha dealer or other qualified mechanic.
A service manual is available for purchase
through a Yamaha dealer for owners who
have the mechanical skills, tools, and other
equipment necessary to perform maintenance not covered by this owner’s/operator’s
manual.

UF2N12E0.book Page 85 Monday, July 4, 2011 3:25 PM

Maintenance
EJU37062

Periodic maintenance chart
The periodic maintenance chart gives general guidelines for periodic maintenance. Have a
Yamaha dealer perform the checks in the following chart. However, maintenance may need to
be performed more frequently depending on your operating conditions. If you have any questions, consult a Yamaha dealer.
This “ ” mark indicates items to be checked and serviced by a Yamaha dealer.
Initial
Item

Operation

10
hours

Thereafter every
50 hours

100
hours

200
hours

Page

6
12
12
24
months months months months
Spark plugs

Check, clean, replace

—

Lubrication points

Lubricate

—

Intermediate housing

Lubricate

—

Fuel system

Check

—

Fuel tank

Check, clean

—

Engine idling
speed

Check, adjust

—

Throttle shaft

Check

—

Water inlet strainer

Check, clean

—

Bilge strainer

Clean

—

Impeller

Check

—

Jet thrust nozzle
angle

Check, adjust

—

Shift cable and reverse gate
(VX Deluxe /
VX Cruiser)

Check, adjust

—

Throttle cable

Check

—

Stern drain plugs

Check, replace

—

Battery

Check, charge

—

Rubber coupling

Check

—

Engine mount

Check

—

Nuts and bolts

Check

—

Air filter element

Check

—

UF2N12E0.book Page 86 Monday, July 4, 2011 3:25 PM

Maintenance
Initial
Item

Operation

10
hours

Thereafter every
50 hours

100
hours

200
hours

Page

6
12
12
24
months months months months
Engine oil

Replace

Oil filter

Replace

Valve clearance

Check, adjust

—

EJU36942

Engine oil and oil filter
EWJ00340

WARNING
Engine oil is extremely hot immediately after the engine is turned off. Coming in contact with or getting any engine oil on your
clothes could result in burns.
ECJ00991

NOTICE
Do not run the engine with too much or not
enough oil in the engine, otherwise the engine could be damaged.
It is recommended to have a Yamaha dealer
change the engine oil and the engine oil filter.
However, if you choose to change the oil and
filter on your own, consult a Yamaha dealer.

UF2N12E0.book Page 87 Monday, July 4, 2011 3:25 PM

Specifications
EJU34542

Specifications
Watercraft capacity:
Maximum people on board:
3 person
Maximum load capacity:
240 kg (530 lb)

Dimensions:
Length:
VX Sport 3220 mm (126.8 in)
VX Deluxe 3220 mm (126.8 in)
VX Cruiser 3270 mm (128.7 in)
Width:
1170 mm (46.1 in)
Height:
1160 mm (45.7 in)
Dry weight:
VX Sport 334 kg (736 lb)
VX Deluxe 337 kg (743 lb)
VX Cruiser 340 kg (750 lb)

Performance:
Maximum fuel consumption:
28.1 L/h (7.4 US gal/h, 6.2 Imp.gal/h)
Cruising range at full throttle:
2.14 hour
Trolling speed:
1650 ±50 r/min

Engine:
Engine type:
Liquid cooled 4-stroke, DOHC
Number of cylinders:
4
Engine displacement:
1052 cm³
Bore & stroke:
76.0 × 58.0 mm (2.99 × 2.28 in)
Compression ratio:
11.4 : 1
Valve clearance-intake (cold):
0.11–0.20 mm (0.0043–0.0079 in)
Valve clearance-exhaust (cold):
0.25–0.34 mm (0.0098–0.0134 in)
Lubrication system:
Dry sump
Cooling system:
Water
Starting system:
Electric

Ignition system:
T.C.I.
Spark plug:
CR9EB
Spark plug gap:
0.7–0.8 mm (0.028–0.031 in)
Battery capacity:
12 V, 19 Ah
Charging system:
Flywheel magneto

Drive unit:
Propulsion system:
Jet pump
Jet pump type:
Axial flow, single stage
Impeller rotation:
Counterclockwise
Jet thrust nozzle angle:
24.0+24.0 °

Fuel and oil:
Recommended fuel:
Regular unleaded gasoline
Minimum octane rating (PON):
86
Minimum octane rating (RON):
90
Recommended engine oil type SAE:
SAE 10W-30, 10W-40, 20W-40, 20W-50
Recommended engine oil grade API:
API SE,SF,SG,SH,SJ,SL
Fuel tank total capacity:
60 L (15.9 US gal, 13.2 Imp.gal)
Engine oil quantity with oil filter replacement:
2.2 L (2.33 US qt, 1.94 Imp.qt)
Engine oil quantity without oil filter replacement:
2.0 L (2.11 US qt, 1.76 Imp.qt)
Engine oil total quantity:
4.3 L (4.55 US qt, 3.78 Imp.qt)

UF2N12E0.book Page 88 Monday, July 4, 2011 3:25 PM

Trouble recovery
EJU34561

Troubleshooting
If you have any trouble with your watercraft, use the troubleshooting chart to check for the possible cause.
If you cannot find the cause, consult a Yamaha dealer.
EJU34595

Troubleshooting chart
Confirm the possible cause and remedy, and then refer to the applicable page.
TROUBLE
Engine does not
start (Starter motor
does not turn over)

POSSIBLE CAUSE

PAGE

Yamaha Security System
(VX Deluxe /
VX Cruiser)

Lock mode selected

Engine shutoff switch

Clip not in place

Install clip

Fuse

Burned out

Replace fuse and
check wiring

Run down

Recharge

Poor terminal connections

Tighten as required

Battery

Starter motor
Engine does not
start (Starter motor
turns over)

REMEDY
Select unlock mode

Terminal corroded

Clean or replace

Faulty

Have serviced by
Yamaha dealer

—

Throttle lever

Squeezed

Release

Fuel

Empty

Refill as soon as possible

Stale or contaminated

Have serviced by
Yamaha dealer

—

Fuel tank

Water or dirt present

Have serviced by
Yamaha dealer

—

Spark plug

Fouled or defective

Have serviced by
Yamaha dealer

—

Spark plug
cap

Not connected or
loose

Have serviced by
Yamaha dealer

—

Connected to wrong
cylinder

Have serviced by
Yamaha dealer

—

Fuel pump faulty

Have serviced by
Yamaha dealer

—

Fuel injection system

UF2N12E0.book Page 89 Monday, July 4, 2011 3:25 PM

Trouble recovery
TROUBLE
Engine runs irregularly or stalls

POSSIBLE CAUSE

REMEDY

PAGE

Empty

Refill as soon as possible

Stale or contaminated

Have serviced by
Yamaha dealer

—

Fuel tank

Water or dirt present

Have serviced by
Yamaha dealer

—

Spark plug

Fouled or defective

Have serviced by
Yamaha dealer

—

Incorrect heat range

Have serviced by
Yamaha dealer

—

Gap incorrect

Have serviced by
Yamaha dealer

—

Not connected or
loose

Have serviced by
Yamaha dealer

—

Cracked, torn, or
damaged

Have serviced by
Yamaha dealer

—

Electrical wiring

Loose connection

Have serviced by
Yamaha dealer

—

Fuel injection system

Faulty or clogged injectors

Have serviced by
Yamaha dealer

—

Fuel level

Empty

Refill as soon as possible

Oil pressure
warning

Oil pressure dropped

Have serviced by
Yamaha dealer

Engine overheated

Jet intake clogged

Clean

Check engine
warning

Faulty sensors

Have serviced by
Yamaha dealer

Fuel

Spark plug
cap

Warning light or indicator blinks or
comes on

91
44

UF2N12E0.book Page 90 Monday, July 4, 2011 3:25 PM

Trouble recovery
TROUBLE
Watercraft slow or
loses power

POSSIBLE CAUSE
Watercraft
operation
mode
(VX Deluxe /
VX Cruiser)
Cavitation

Low RPM mode activated

REMEDY

PAGE

Deactivate Low RPM
Mode
38

Jet intake clogged

Clean

Impeller damaged or
worn

Have serviced by
Yamaha dealer

Engine overheat warning

Engine speed reduction control activated

Clean jet intake and
cool engine

Oil pressure
warning

Engine speed reduction control activated

Add oil

Spark plug

Fouled or defective

Have serviced by
Yamaha dealer

—

Incorrect heat range

Have serviced by
Yamaha dealer

—

Gap incorrect

Have serviced by
Yamaha dealer

—

Spark plug
cap

Not connected or
loose

Have serviced by
Yamaha dealer

—

Electrical wiring

Loose connection

Have serviced by
Yamaha dealer

—

Fuel

Stale or contaminated

Have serviced by
Yamaha dealer

—

Air filter

Clogged

Have serviced by
Yamaha dealer

—

Oil buildup

Have serviced by
Yamaha dealer

—

UF2N12E0.book Page 91 Monday, July 4, 2011 3:25 PM

Trouble recovery
EJU34623

Emergency procedures
EJU34634

ways stop the engine before beaching the watercraft.

Cleaning the jet intake and impeller
EWJ00782

WARNING
Before attempting to remove weeds or debris from the jet intake or impeller area,
shut the engine off and remove the clip
from the engine shut-off switch. Severe injury or death could result from coming in
contact with the rotating parts of the jet
pump.
If weeds or debris gets caught in the jet intake
or impeller, cavitation can occur, causing jet
thrust to decrease even though engine speed
rises. If this condition is allowed to continue,
the engine will overheat and may seize.
NOTICE: If weeds or debris gets caught in
the jet intake, do not operate the watercraft
above trolling speed until they have been
removed. [ECJ00653]
If there is any sign that the jet intake or impeller is clogged with weeds or debris, return to
shore and check the intake and impeller. Al-

ST
OP

(1) Place a suitable clean cloth or carpeting
underneath the watercraft to protect it
from abrasions and scratches. Turn the
watercraft on its side as shown. NOTICE:
Always turn the watercraft over onto
its port (left) side. When turning the
watercraft on its side, support the bow
so that the handlebars are not bent or
damaged. [ECJ00661]

UF2N12E0.book Page 92 Monday, July 4, 2011 3:25 PM

Trouble recovery
(2) Remove any weeds or debris from
around the jet intake, drive shaft, impeller, jet pump housing, and jet thrust nozzle.
If debris is difficult to remove, consult a
Yamaha dealer.

(3) Connect the other end of the negative (–)
jumper cable to an engine hanger.

EJU34641

Jumping the battery
If the watercraft battery has run down, the engine can be started using a 12-volt booster
battery and jumper cables.
EJU34663

Connecting the jumper cables
EWJ01250

WARNING
To avoid battery explosion and serious
damage to the electrical system:
● Do not reverse the polarity of the jumper
cables when connecting to the batteries.
● Do not connect the negative (–) jumper
cable to the negative (–) terminal of the
watercraft battery.
● Do not touch the positive (+) jumper cable to the negative (–) jumper cable.
(1) Connect the positive (+) jumper cable to
the positive (+) battery terminals of both
batteries.
(2) Connect one end of the negative (–)
jumper cable to the negative (–) battery
terminal of the booster battery.

1
2
3
4

Negative (–) jumper cable
Booster battery
Positive (+) jumper cable
Engine hanger

(4) Start the engine, and then disconnect the
jumper cables by reversing the steps
above. (See page 33 for information on
starting the engine.)
EJU34695

Replacing the fuses
If a fuse is blown, replace it with the proper
fuse.

1 Good fuse
2 Blown fuse

To replace a fuse:
(1) Remove the seat. (See page 45 for seat
removal and installation procedures.)

UF2N12E0.book Page 93 Monday, July 4, 2011 3:25 PM

Trouble recovery
(2) Loosen the cap on the electrical box and
remove it.

electrical system damage and possible fire. [EWJ00802]

1
1
2
2
3
1 Electrical box
2 Cap

(3) Replace the blown fuse with the spare
fuse of the correct amperage by using the
fuse puller on the reverse side of the cap.
WARNING! Do not use fuses of a different amperage than recommended.
Substitution with a fuse that has an
improper rating can cause extensive

1 Spare fuse
2 Fuse
3 Cap

1 Fuse puller

Fuse amperage:
Battery fuse:
30 A
Main relay drive fuse:
10 A
Electronic throttle valve fuse:
10 A
Security system fuse:
3A
Main fuse:
20 A
(4) Securely install the cap by tightening it
until it stops.
(5) Securely install the seat in its original position.

UF2N12E0.book Page 94 Monday, July 4, 2011 3:25 PM

Trouble recovery
If the fuse immediately blows again, the electrical system may be defective. If this occurs,
have a Yamaha dealer service the watercraft.
EJU34715

Towing the watercraft
EWJ00811

WARNING
●

●

The operator of the towing boat must
keep speed to a minimum and avoid traffic or obstacles which could be a hazard
to the operator on the watercraft.
The towline should be long enough so
that the watercraft will not collide with
the towing boat when slowing down.

If the watercraft becomes inoperative in the
water, it can be towed to shore.
To tow the watercraft:
Use a towline that is three times the combined
length of the towing boat and the watercraft.
(1) Securely attach the towline to the bow
eye of the watercraft being towed.

Tow the watercraft at 8 km/h (5 mph) or less.
NOTICE: Tow the watercraft at 8 km/h (5
mph) or less, otherwise water could flood
the engine compartment or water could
flow back into the engine, causing severe
engine damage. [ECJ01321]
EJU36155

Submerged watercraft
If the watercraft is submerged or flooded with
water, drain the bilge water from the engine
compartment. Then, have a Yamaha dealer
service the watercraft as soon as possible.
If the watercraft was submerged:
(1) Remove the watercraft from the water
and drain the water from the storage
compartments. (See page 47 for information on draining the storage compartments.)
(2) Drain the bilge water from the engine
compartment. (See page 54 for information on draining the bilge water.)
(3) Have the watercraft serviced by a
Yamaha dealer as soon as possible.
NOTICE: Be sure to have a Yamaha
dealer inspect the watercraft. Otherwise, serious engine damage could result. [ECJ00791]

1 Bow eye

(2) Sit astride the seat and hold on to the
handlebars in order to balance the watercraft. NOTICE: The bow must be kept
up out of the water during towing, otherwise water could flood the engine
compartment or water could flow back
into the engine, causing severe engine damage. [ECJ01330]

UF2N12E0.book Page 95 Monday, July 4, 2011 3:25 PM

Consumer information
EJU34781

Limited warranty
YAMAHA MOTOR CORPORATION, U.S.A.
WATERCRAFT LIMITED WARRANTY
Yamaha Motor Corporation is proud of its heritage and reputation for producing products with high standards of quality and workmanship. Product excellence provides the cornerstone for our commitment to customer satisfaction. The Yamaha Watercraft Limited Warranty is your assurance of this commitment.
This warranty provides you with protection against the expense of repairs for your watercraft that are required as a result of defects in
materials or workmanship. When maintained and utilized in the prescribed manner, you can count on your Yamaha watercraft to provide reliable service.
This warranty provides you with specific coverage and notes your responsibilities in maintaining and operating your watercraft.
Please take the time to read and become familiar with this warranty.
PERIOD OF WARRANTY. Any new Yamaha watercraft purchased for pleasure use from an authorized Yamaha dealer in the United
States, will be warranted against defects in material or workmanship for a period of one (1) year from date of purchase, subject to
exclusions noted herein. Any Yamaha Watercraft purchased and utilized for commercial applications will be warranted for a period of
ninety [90] days from the date of purchase, subject to exclusions noted herein. Replacement parts used in warranty repairs will be warranted for the balance of the applicable warranty period.
The warranty described here applies to watercrafts purchased and registered for use in the United States only. For warranty provisions
outside the United States, contact the particular country’s local Yamaha distributor.
OBTAINING REPAIRS UNDER WARRANTY. During the period of warranty, any authorized Yamaha dealer will, free of charge, repair
or replace, at Yamaha’s option, any parts adjudged defective by Yamaha due to faulty workmanship or material from the factory. All
parts replaced under warranty will become the property of Yamaha Motor Corporation, U.S.A.
CUSTOMER’S RESPONSIBILITY. Under the terms of this warranty, the customer will be responsible for ensuring that the watercraft is
properly operated, maintained, and stored as specified in the applicable Owner’s/Operator’s Manual.
The owner of the watercraft shall give notice to an authorized Yamaha dealer of any and all apparent defects within ten [10] days of discovery and make the watercraft available at that time for inspection and repairs at the dealer’s place of business.
GENERAL EXCLUSIONS FROM WARRANTY. This warranty will not cover the repair of damage if the damage is a result of abuse or
neglect of the product. Examples of abuse and neglect include, but are not limited to:
1. Racing or competition use, modification of original parts abnormal strain.
2. Lack of proper maintenance and off season storage as described in the Owner’s/Operator’s Manual, installation of parts or accessories that are not equivalent in design and quality to genuine Yamaha parts.
3. Use of lubricants, oils, and fuel/oil mixtures that are not suitable for watercraft motor use.
4. Damage as a result of accidents, collisions, contact with foreign materials, or submersion.
5. Growth of marine organisms on motor or hull surfaces.
6. Normal deterioration.
7. Gel coat stress cracks.
SPECIFIC PARTS EXCLUDED FROM WARRANTY.
Parts replaced due to normal wear or routine maintenance such as oil, spark plugs, fuel filters, impeller and liner, and anodes are not
covered by warranty. Charges for transporting the watercraft to and from an authorized Yamaha dealer are excluded from warranty coverage.
TRANSFER OF WARRANTY. Transfer of the warranty from the original purchaser to any subsequent purchaser is possible by having
the watercraft inspected by an authorized Yamaha dealer and requesting the dealer to submit a change of registration to Yamaha Motor
Corporation. U.S.A. within ten [10] days of the transfer.
EMISSION CONTROL WARRANTY. Yamaha warrants to the ultimate purchaser and any subsequent owner, that the emission control
components on this engine are designed, built and equipped so as to conform at the time of sale with applicable regulations under
section 213 of the Clean Air Act and that this engine is free from defects in materials and workmanship which cause said engine to fail
to conform with applicable regulations for thirty (30) months from the date of purchase or 175 hours of operation, whichever comes first,
and, for evaporative emission components, for twenty-four (24) months from the date of purchase. Some states have different emission
control warranty provisions. As these vary from state to state, consult your Yamaha dealer or contact Yamaha Customer Relations at 1800-962-7926 for more information.

YAMAHA MOTOR CORPORATION, U.S.A. MAKES NO OTHER WARRANTY OF ANY KIND, EXPRESSED OR IMPLIED. ALL IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE WHICH EXCEED THE OBLIGATIONS AND TIME LIMITS
STATED IN THIS WARRANTY ARE HEREBY DISCLAIMED BY YAMAHA MOTOR CORPORATION, U.S.A. AND EXCLUDED FROM THIS
WARRANTY.
SOME STATES DO NOT ALLOW LIMITATIONS ON HOW LONG AN IMPLIED WARRANTY LASTS, SO THE ABOVE LIMITATION MAY NOT
APPLY TO YOU. ALSO EXCLUDED FROM THIS WARRANTY ARE ANY INCIDENTAL OR CONSEQUENTIAL DAMAGES INCLUDING LOSS
OF USE. SOME STATES DO NOT ALLOW THE EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES, SO THE
ABOVE EXCLUSION MAY NOT APPLY TO YOU.

UF2N12E0.book Page 96 Monday, July 4, 2011 3:25 PM

Consumer information
THIS WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS, AND YOU MAY ALSO HAVE OTHER RIGHTS WHICH VARY FROM STATE TO
STATE.
YAMAHA MOTOR CORPORATION, U.S.A.
Post Office Box 6555
Cypress, California 90630
WARRANTY QUESTIONS AND ANSWERS
Q. What costs are my responsibility during the warranty period?
A. The customer’s responsibility includes all costs of normal maintenance services, non-warranty repairs, accident and collision damages.
Q. What are some examples of “abnormal” strain, neglect, or abuse?
A. These terms are general and overlap each other in areas. Specific examples include:
Running the watercraft out of oil, operating the machine with a broken or damaged part which causes another part to fail, and so
on. If you have any specific questions on operation or maintenance, please contact your Yamaha dealer for advice.
Q. Does the warranty cover incidental costs such as transportation due to a failure?
A. No. The warranty is limited to repair of the watercraft itself.
Q. May I perform any or all of the recommended maintenance shown in the Owner’s/Operator’s Manual instead of having the dealer do
them?
A. Yes, if you are a qualified mechanic and follow the procedures specified in the Owner’s/Operator’s and Service Manual. We do recommend, however, that items requiring special or equipment be done by a Yamaha dealer.
Q. Will the warranty be void or cancelled if I do not operate or maintain my new watercraft exactly as specified in the Owner’s/Operator’s Manual?
A. No. The warranty on a new watercraft cannot be “voided” or “cancelled”. However, if a particular failure is caused by operation
or maintenance other than as shown in the Owner’s/Operator’s Manual, that failure may not be covered under warranty.
Q. What responsibility does my dealer have under this warranty?
A. Each Yamaha dealer is expected to:
1. Completely set up each new watercraft before sale.
2.
Explain the operation, maintenance, and warranty requirements to your satisfaction at the time of sale, and upon your request at
any later date. In addition, each Yamaha dealer is held responsible for his setup, service and warranty repair work.
Q. Is the warranty transferable to second owners?
A. Yes. The remainder of the existing warranty can be transferred upon request. The unit has to be inspected and re-registered by an
authorized Yamaha dealer for the policy to remain effective.
CUSTOMER SERVICE
If your watercraft requires warranty service, you must take it to any authorized Yamaha dealer within the continental United States. Be
sure to bring your warranty registration card or other valid proof of the original date of purchase. If a question or problem arises regarding warranty, first contact the owner of the dealership. Since all warranty matters are handled at the dealer level, this person is in the
best position to help you. If you are still not satisfied and require additional assistance, please write:
YAMAHA MOTOR CORPORATION U.S.A.
CUSTOMER RELATIONS DEPARTMENT
P.O. Box 6555
Cypress, California 90630
CHANGE OF ADDRESS
The federal government requires each manufacturer to maintain a complete, up-to-date list of all first purchasers against the possibility
of a safety-related defect and recall. This list is complied from the purchase registrations sent to Yamaha Motor Corporation, U.S.A. by
the selling dealer at the time of your purchase.
If you should move after you have purchased your new watercraft, please advise us of your new address by sending a postcard listing
your Yamaha model name, engine number, dealer number [or dealer’s name] as it is shown on your warranty card, your name and new
mailing address.
Mail to:
YAMAHA MOTOR CORPORATION, U.S.A.
P.O. Box 6555
Cypress, California 90630
Attention: Warranty Department
This will ensure that Yamaha Motor Corporation, U.S.A. has an up-to-date registration record in accordance with federal law.

UF2N12E0.book Page 97 Monday, July 4, 2011 3:25 PM

Consumer information
EJU34801

YAMAHA EXTENDED SERVICE (Y.E.S.)
Keep your Yamaha protected even after your warranty expires with genuine Yamaha Extended
Service (Y.E.S.).

•

Y.E.S. is designed and administered by Yamaha Motor Corporation to provide maximum owner
satisfaction. You get uninterrupted factory-backed coverage for extra peace of mind.

•

Y.E.S. is flexible. You choose the plan that is right for you: 12 months, 24 months, 36 months, or
(on four-stroke models) 48 months beyond your warranty period.

•

Y.E.S. is designed and administered by the same Yamaha people who handle your warranty—
and it shows in the comprehensive coverage benefits. There are no mileage limitations. Coverage is not limited to “moving parts” or the “drive train” like many other plans. And Y.E.S. covers
manufacturing defects just like the warranty. See the sample contract at your Yamaha dealer to
see how comforting uninterrupted factory-backed protection can be.

•

You do not have to pay anything for covered repairs. There is no deductible to pay, and repairs
are not “pro-rated.” You do not have any “out-of-pocket” expenses for covered repairs.

•

In addition, Travel and Recreation Interruption Protection (TRIP) is included at no extra cost.
TRIP gives you up to $250 reimbursement per occurrence for any reasonable expenses you
incur because your Yamaha needs covered service: replacement vehicle rental, emergency
towing, phone calls, even food and lodging when you are away from home. This superb coverage goes into effect when you purchase Y.E.S., so it applies to any warranty repairs as well as
covered repairs during your entire Y.E.S. plan period.

•

Y.E.S. coverage is honored at any authorized Yamaha dealer nationwide.

•

Y.E.S. coverage is transferable to a new owner if you sell or trade-in. That can make your
Yamaha much more valuable!

This excellent Y.E.S. plan coverage is only available to Yamaha owners like you, and only while
your Yamaha is still within the Yamaha Limited Warranty period. So visit your authorized Yamaha
dealer to get all the facts. He can show you how easy it is to protect your investment with Yamaha
Extended Service.
We urge you to act now. You will get the excellent benefits of TRIP coverage right away, and you
will rest easy knowing you will have strong factory-backed protection even after your Yamaha
Limited Warranty expires.
A special note:
If visiting your dealer is not convenient, contact Yamaha with your Primary ID number (your Owner’s
Manual shows you where to find this number). We will be happy to help you get the Y.E.S. coverage
you need.
Yamaha Service Marketing
P.O. Box 6555
Cypress, CA 90630
1-(866)-YES-EXTD
(1-866-937-3983)

UF2N12E0.book Page 1 Monday, July 4, 2011 3:25 PM

Index
A
After removing the watercraft
from the water....................................... 77
Approval label of emission control
certificate ................................................ 2
B
Battery care.............................................. 79
Battery checks.......................................... 60
Battery, jumping ....................................... 92
Beaching and docking the watercraft ....... 76
Beverage holder....................................... 49
Bilge water check ..................................... 60
Bilge water, draining................................. 54
Bilge water, draining on land.................... 54
Bilge water, draining on water.................. 54
Boarding alone ......................................... 72
Boarding and starting off from a dock ...... 75
Boarding the watercraft ............................ 71
Boarding with passenger(s) ..................... 72
Bow eye ................................................... 46
Bow storage compartment ....................... 47
C
Capsized watercraft ................................. 75
Check engine warning.............................. 44
Cleaning ................................................... 82
Cleaning the watercraft ............................ 79
Cleat......................................................... 47
Cooling water pilot outlet.......................... 35
Cooling water pilot outlet check ............... 65
Cruising limitations ................................... 11
E
Emergency procedures ............................ 91
Emission control information ...................... 2
Engine break-in ........................................ 56
Engine compartment check...................... 59
Engine idling speed check ....................... 65
Engine oil ................................................. 52
Engine oil and oil filter .............................. 86
Engine oil level check............................... 59
Engine oil requirements ........................... 52
Engine overheat warning ......................... 43
Engine serial number ................................. 1
Engine shut-off cord (lanyard) check ....... 62
Engine shut-off switch .............................. 33
Engine stop switch ................................... 33

Engine unit check..................................... 59
Enjoy your watercraft responsibly ............ 24
Equipment ................................................ 45
F
Fire extinguisher check ............................ 64
Fire extinguisher holder and cover ........... 49
Fire extinguisher holder, cover,
and band checks................................... 63
Flushing the cooling water passages ....... 78
Fuel .......................................................... 51
Fuel level check ....................................... 59
Fuel level meter........................................ 42
Fuel level warning .................................... 42
Fuel requirements .................................... 51
Fuel system checks.................................. 59
Fuses, replacing ....................................... 92
G
Getting to know your watercraft ............... 66
Glossary, watercraft ................................. 26
Glove compartment .................................. 48
H
Handgrip................................................... 46
Hazard information ................................... 16
Hood check .............................................. 65
Hour meter/voltmeter ............................... 41
Hull and deck check ................................. 64
Hull Identification Number (HIN)................. 1
I
Identification numbers ................................ 1
Information display ................................... 40
J
Jet intake and impeller, cleaning .............. 91
Jet intake checks...................................... 64
Jumper cables, connecting ...................... 92
L
Labels, important........................................ 5
Labels, other .............................................. 8
Labels, warning .......................................... 6
Launching the watercraft .......................... 67
Learning to operate your watercraft ......... 66
Leaving the watercraft .............................. 68
Limitations on who may operate
the watercraft ........................................ 10
Limited warranty ....................................... 95
Long-term storage .................................... 82

UF2N12E0.book Page 2 Monday, July 4, 2011 3:25 PM

Index
Low RPM Mode
(VX Deluxe / VX Cruiser) ...................... 38
Lubrication................................................ 82
M
Main components, location of .................. 27
Maintenance............................................. 84
Manufactured date label............................. 3
Multifunction information center ............... 40
Multifunction information center check..... 65
O
Oil pressure warning ................................ 43
Operating in weeded areas ...................... 77
Operating the watercraft........................... 68
Operating the watercraft in reverse
(VX Deluxe / VX Cruiser) ...................... 71
Operating your watercraft......................... 66
Operation requirements ........................... 13
P
Periodic maintenance chart...................... 85
Post-launch checks .................................. 65
Post-operation care.................................. 78
Pre-launch checks.................................... 59
Pre-operation check points ...................... 59
Pre-operation checklist............................. 57
Primary Identification (PRI-ID) number ...... 1
R
Reboarding step (VX Cruiser) .................. 46
Recommended equipment ....................... 15
Remote control transmitter check
(VX Deluxe / VX Cruiser) ...................... 62
Remote control transmitter
(VX Deluxe / VX Cruiser) ...................... 31
Reverse system checks
(VX Deluxe / VX Cruiser) ...................... 61
Reverse system
(VX Deluxe / VX Cruiser) ...................... 37
Riding position.......................................... 67
Rules of the Road .................................... 19
Rustproofing............................................. 83
S
Safety equipment check........................... 64
Seat.......................................................... 45
Speedometer............................................ 40
Star labels .................................................. 3
Start switch............................................... 33

Starting off ................................................ 74
Starting off from a trailer........................... 75
Starting the engine on water .................... 67
Steering system ....................................... 34
Steering system checks ........................... 60
Stern drain plug checks............................ 64
Stern eyes ................................................ 47
Stopping the engine ................................. 68
Stopping the watercraft ............................ 70
Storage compartment checks .................. 63
Storage compartments ............................. 47
Submerged watercraft .............................. 94
Switch checks .......................................... 63
T
Tachometer .............................................. 41
Throttle lever ............................................ 34
Throttle lever checks ................................ 62
To get more boating safety information.... 23
Tool kit...................................................... 84
Towing the watercraft ............................... 94
Transporting on a trailer ........................... 55
Troubleshooting ....................................... 88
Troubleshooting chart .............................. 88
Turning the watercraft .............................. 69
W
Water separator ....................................... 35
Water separator check ............................. 59
Watercraft characteristics......................... 16
Watercraft control functions ..................... 31
Watercraft operation functions ................. 37
Watercraft operation modes ..................... 38
Water-skiing ............................................. 18
Y
YAMAHA EXTENDED SERVICE
(Y.E.S.) ................................................. 97
Yamaha Security System settings ........... 32
Yamaha Security System
(VX Deluxe / VX Cruiser) ...................... 32

UF2N12E0.book Page 1 Monday, July 4, 2011 3:25 PM

EJU42010

For your best ownership experience, think Genuine Yamaha!
Genuine Yamaha Parts – Genuine Yamaha replacement parts are the exact same
parts as the ones originally equipped on your vehicle, providing you with the
performance and durability you have come to expect. Why settle for aftermarket parts
that may not provide full confidence and satisfaction?
Genuine Yamaha Accessories – Yamaha only offers accessories that meet our
high standards for quality and performance. Buy with confidence, knowing your
Genuine Yamaha Accessories will fit right and perform right – right out of the box.
Yamalube – Take care of your Yamaha with legendary Yamalube oils, lubricants,
and care products. They’re formulated and approved by the toughest judges we
know: the Yamaha engineering teams that know your Yamaha from the inside out.
Genuine Yamaha Service Manuals – Get the same factory manual for your vehicle
that the technicians at your authorized Yamaha dealer use. Service manuals are
available through your Yamaha dealer or you can order them directly through
yamahapubs.com.
Genuine Yamaha products are available only from your Yamaha dealer.
Find out more at yamaha-motor.com

Printed in USA
July 2011–0.7 × 1 CR

DIC183

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.6
Linearized                      : Yes
Encryption                      : Standard V4.4 (128-bit)
User Access                     : Extract
Author                          : 
Create Date                     : 2011:07:04 15:22:57Z
Modify Date                     : 2012:05:04 15:39:06-07:00
XMP Toolkit                     : Adobe XMP Core 5.2-c001 63.139439, 2010/09/27-13:37:26
Creator Tool                    : FrameMaker 6.0
Metadata Date                   : 2012:05:04 15:39:06-07:00
Format                          : application/pdf
Creator                         : 
Title                           : 
Producer                        : Acrobat Distiller 4.05 for Windows
Document ID                     : uuid:bbc59bba-6359-413c-b3e8-c22aeea9b91a
Instance ID                     : uuid:59283e0e-7054-4a78-a254-d47443d9bd66
Page Mode                       : UseNone
Page Count                      : 106

EXIF Metadata provided by EXIF.tools

Yamaha DIC183 User Manual To The A9da5c2e 592d 4837 B789 F65f0c7693bd

Navigation menu

Versions of this User Manual:

Views

Navigation