Yamaha Nexo Geo S12 Series And Ls18 User Users Manual V105

2015-03-09

: Yamaha Nexo-Geo-S12-Series-And-Ls18-User-Users-Manual yamaha-nexo-geo-s12-series-and-ls18-user-users-manual-647511 yamaha pdf

Open the PDF directly: View PDF PDF.
Page Count: 103 [warning: Documents this large are best viewed by clicking the View PDF Link!]

GEO S12 Series
Geo S1210 & Geo S1230 Tangent Array Modules
LS18 & LS18e Subwoofer
User Manual
GEO S12 Series User Manual V1.05
Date: 2013/07/01
Page 2/103 PLEASE READ CAREFULLY BEFORE PROCEEDING
GEO Technology is radically new thinking
The GEO R&D Project has, to date, resulted in the following patent applications:
The GEO Hyperboloid Reflective Wavesource™ differs radically from the megaphone-
variant type horns you know and love (or hate). “Tried and true” methods will produce
entirely unexpected results. HRW technology produces precise and predictable results.
The Configurable Directivity Flange. A waveguide that allows the operator to alter its
behaviour. An unprecedented NEXO development that is easy to use – once you know
how and when.
The Directivity Phase Device needs no operator input to function, but it is reassuring to
know that the coupling of the midrange of the system is considered as important as the
high frequencies…
DSP-driven Directional Sub-bass devices are a new approach to controlling LF/VLF
acoustic energy.
GEO is not hard to use when you understand how…
The technology behind GEO is revolutionary, but it is grounded in years of practical experience with the
problems of delivering high quality professional sound to large audiences at high SPL levels. The GEO
toolbox includes NS-1 - a simple yet powerful and highly predictive design tool. The array assembly
system is keyed to the design software and will easily enable you to deploy your design with great
precision. The NXAMP Amplified Digital TDcontroller provides driver protection and system optimization
as well as DSP-driven cardioid pattern control for the LS and RS series Subwoofers.
GEO is a high precision system
The GEO HRW™ controls acoustic energy more precisely than other multiple element waveguides. It
also makes GEO less forgiving of mistakes. Whilst conventional horns never combine into a coherent
array, they may deliver acceptable results even if the design and deployment of the system is less than
optimal. This is not the case with GEO where careless installation produces catastrophic results.
A GEO Tangent Array is not a “line array”
GEO Technology is equally effective in designing and deploying tangent horizontal arrays or curved
vertical arrays. For best results in a specific application the user needs to know how multi-speaker
arrays interact with audience geometry, along with the benefits and drawbacks of curved vertical arrays
and horizontal arrays.
Curved tangent arrays require different design techniques
For the past 20 years, sound reinforcement professionals have worked with horizontal arrays that use
conventional horns to deliver [more or less] ‘equal power to equal angles’. Curved vertical arrays are
designed to deliver [more or less] equal power to equal areas’. When arrays use conventional horns,
the lack of precision, overlap and interference masks errors in array design and aiming. The highly
precise GEO wavesource responds accurately, consistently and predictably to the design and
deployment of a curved vertical tangent array. This is why the GEO rigging system is designed to
control angular splay to 0.01° precision.
GEO curved tangent arrays require different operational techniques
Over the years, system designers and operators have developed a number of signal processing
techniques to disguise and partly overcome the limitations of horn design. “Frequency shading,”
“amplitude shading,” “system tuning,” all of these are tools of the advanced sound system operator.
NONE OF THESE TECHNIQUES ARE APPLICABLE TO GEO TANGENT ARRAYS. Instead of
enhancing the array’s performance they will severely degrade it.
Take time to learn how to get great results with GEO Technology. It is an investment that will pay off in
more satisfied clients, more efficient operating procedures and more recognition for your skill as a
sound system designer and operator. A comprehensive understanding of GEO theory, tangent arrays,
and specific features of the GEO S12 Series will help you to operate your system at its full potential.
PLEASE READ CAREFULLY BEFORE PROCEEDING Page 3/103
PLEASE READ CAREFULLY BEFORE PROCEEDING
BASIC PRECAUTIONS
Do not open the speaker system or attempt to disassemble the internal parts or modify them in any
way. The speaker system contains no user-serviceable parts. If it should appear to be malfunctioning or
damaged, discontinue use immediately and have it inspected by qualified NEXO service personnel.
Water exposure: Do not expose the speaker system to direct rain, do not use it near water or in wet
conditions. Do not place containers with liquid on speaker system as they might spill into openings. If
any liquid such as water seeps into the speaker system, have it inspected by qualified NEXO personnel.
SYSTEM DEPLOYMENT SAFETY RULES
Read User Manual before deployment. Before use of enclosed speaker system,
please ensure that anyone involved in system deployment understands the rigging ‒
stacking ‒ pole mounting safety rules as described in the speaker system User Manual.
Failure to do this exposes people to potential injury or death.
Always consult qualified NEXO personnel if the device installation requires construction work and make
sure to observe the following precautions:
Mounting precautions
- choose mounting hardware and an installation location that can support the weight of the speaker
system;
- do not use speaker system handles for suspended installation;
- do not expose speaker system to excessive dust or vibration, or extreme cold or heat to prevent
possibility of component damage;
- do not place the speaker system in an unstable position from which it might fall accidentally;
- if speaker systems uses a stand, ensure that stand specifications are adapted, and that stand
height does not exceed 1.40m/55; never move the stand while the speaker is in position.
Connection and powering precautions
- remove all connected cables before moving the speaker system;
- turn off AC power of all power amplifier units before connecting the speaker system;
- when turning on the AC power to the audio system, always turn on the power amplifier last; when
turning the AC power off, always turn off the power amplifier first;
- when used in cold conditions, a gradual power ramp up should applied to the system on an 5 mn
period to allow the loudspeaker components to stabilize during the very first minutes of usage.
Inspect the speaker system periodically.
Page 4/103 PLEASE READ CAREFULLY BEFORE PROCEEDING
SAFETY INSTRUCTIONS FOR NEXO TD CONTROLLERS
NEXO ANALOGUE PSTDCONTROLLERS, NX242 DIGITAL CONTROLLER,
NXAMP4x1 AND NXAMP4x4 POWERED CONTROLLERS ARE CLASS 1
APPARATUS AND MUST BE EARTHED.
THE GREEN AND YELLOW WIRE OF THE MAINS CORD MUST ALWAYS BE CONNECTED TO AN
INSTALLATION SAFETY EARTH OR GROUND. THE EARTH IS ESSENTIAL FOR PERSONAL
SAFETY AS WELL AS THE CORRECT OPERATION OF THE SYSTEM, AND IS INTERNALLY
CONNECTED TO ALL EXPOSED METAL SURFACES.
- Read these instructions.
- Keep these instructions.
- Heed all warnings.
- Follow all instructions.
- Do not use this apparatus near water.
- Clean only with dry cloth.
- Do not block any ventilation openings. Install in accordance with the manufacturers instructions.
- Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus
(including amplifiers) that produce heat.
- Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two
blades with one wider than the other. A grounding type plug has two blades and a third grounding
prong. The wide blade or the third prong are provided for your safety. If the provided plug does not
fit into your outlet, consult an electrician for replacement of the obsolete outlet. (US market)
- Protect the power cord from being walked on or pinched particularly at plugs, convenience
receptacles, and the point where they exit from the apparatus.
- Only use attachments/accessories specified by the manufacturer.
- Unplug this apparatus during lightning storms or when unused for long periods of time.
- Refer all servicing to qualified service personnel. Servicing is required when the apparatus has
been damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled
or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does
not operate normally, or has been dropped.
PLEASE READ CAREFULLY BEFORE PROCEEDING Page 5/103
HIGH SOUND PRESSURE LEVELS
Exposure to extremely high noise levels may cause permanent hearing loss.
Individuals vary considerably in susceptibility to noise-induced hearing loss but nearly
everyone will lose some hearing if exposed to sufficiently intense noise for a sufficient
period of time. The U.S. Governments Occupational and Health Administration (OSHA)
has specified the following permissible noise level exposures: Sound Duration Per
Day In Hours Sound Level dBA, Slow Response
8
90
6
92
4
65
3
97
2
100
1 ½
102
1
105
½
110
¼ or less
115
According to OSHA, any exposure in excess of the above permissible limits could result in some
hearing loss. Ear plugs or protectors to the ear canals or over the ears must be worn when operating
this amplification system in order to prevent permanent hearing loss, if exposure is in excess of the
limits as set forth above. To ensure against potentially dangerous exposure to high sound pressure
levels, it is recommended that all persons exposed to equipment capable of producing high sound
pressure levels such as this amplification system be protected by hearing protectors while this unit is in
operation.
DISPOSAL OF OLD ELECTRICAL & ELECTRONIC EQUIPMENT
This symbol on the product or on its packaging indicates that it shall not be treated
as household waste. Instead it shall be handed over to the applicable collection
point for the recycling of electrical and electronic equipment. By ensuring this
product is disposed of correctly, you will help prevent potential negative
consequence for the environment and human health, which could otherwise be
caused by inappropriate waste handling of this product. The recycling of materials
will help to conserve natural resources. For more detailed information about
recycling of this product, please contact your local city office, your household waste
disposal service or the shop where you purchased the product.
Page 6/103 CONTENTS
CONTENTS
PLEASE READ CAREFULLY BEFORE PROCEEDING ..................................................................................................................... 3
CONTENTS ................................................................................................................................................................................................ 6
1 INTRODUCTION ........................................................................................................................................................................... 8
2 GEO S12 GENERAL SET-UP INSTRUCTIONS .................................................................................................................... 11
2.1 SPEAKER CONNECTION ............................................................................................................................................................................ 11
2.1.1 GEO S12 connectors ....................................................................................................................................................................... 11
2.1.2 LS18 connector ................................................................................................................................................................................ 11
2.1.3 Configuring Geo S12 for Passive or Active Mode ............................................................................................................... 11
2.1.4 Cabling ................................................................................................................................................................................................ 12
2.1.5 Example: ............................................................................................................................................................................................ 12
3 AMPLIFIER SELECTION FOR USE WITH GEO S12 & LS18 ........................................................................................... 14
3.1 GEO S12, LS18 AND NXAMP TDCONTROLLERS ............................................................................................................................ 14
3.1.1 NXAMP connectors......................................................................................................................................................................... 14
3.1.2 GEO S12, LS18 and NXAMP recommended configurations ............................................................................................ 14
4 GEO S12 SETUPS ON NEXO TD CONTROLLERS .............................................................................................................. 15
4.1 NXAMP TDCONTROLLERS .................................................................................................................................................................... 15
5 CONNECTION DIAGRAMS ...................................................................................................................................................... 16
5.1 GEO S12 / NXAMP4X1 (BRIDGE STEREO – S12 IN PASSIVE MODE) .......................................................................................... 16
5.2 GEO S12 / NXAMP4X1 (BRIDGE STEREO – S12 IN ACTIVE MODE) ........................................................................................... 17
5.3 LS18 / NXAMP4X1 (BRIDGE STEREO) ............................................................................................................................................. 18
5.4 LS18 & GEO S12 / NXAMP4X1 (BRIDGE STEREO – S12 IN PASSIVE MODE) ........................................................................... 19
5.5 GEO S12 / NXAMP4X4 (4 CHANNELS – S12 IN PASSIVE MODE) ................................................................................................ 20
5.6 GEO S12 / NXAMP4X4 (S12 IN STEREO ACTIVE MODE) ............................................................................................................. 21
5.7 LS18 / NXAMP4X4 (4 CHANNELS) .................................................................................................................................................... 22
5.8 LS18 & GEO S12 NXAMP4X4 (S12 IN PASSIVE MODE) .............................................................................................................. 23
6 NS-1 SIMULATION SOFTWARE ............................................................................................................................................ 24
7 CONFIGURABLE DIRECTIVITY DEVICE ............................................................................................................................. 25
7.1 INSTALLING & REMOVING GEO’S CONFIGURABLE DIRECTIVITY FLANGES ..................................................................................... 25
7.2 WHEN & WHERE TO USE CONFIGURABLE DIRECTIVITY FLANGES .................................................................................................... 26
8 GEO S12 HARDWARE SETUP PROCEDURE ...................................................................................................................... 27
8.1 SAFETY FIRST ....................................................................................................................................................................................... 27
8.1.1 Flown Systems Safety .................................................................................................................................................................... 27
8.1.2 Ground Stacking Safety ................................................................................................................................................................ 28
8.1.3 Contacts .............................................................................................................................................................................................. 29
8.2 GENERAL DESCRIPTION ........................................................................................................................................................................... 30
8.2.1 Described configurations ............................................................................................................................................................ 31
8.2.2 WARNINGS ON GEO S12 ACCESSORIES ................................................................................................................................ 32
8.3 GEO S12 IN FIXED INSTALLATIONS ...................................................................................................................................................... 33
8.3.1 Fixed installation Accessories and kits................................................................................................................................... 33
8.3.2 Single GEO S12 rigidly mounted on a wall or a ceiling (vertical or horizontal) ................................................... 34
8.3.3 Single GEO S12 cable mounted on a wall or a ceiling (vertical or horizontal) ...................................................... 35
8.3.4 GEO S12 vertical array rigidly mounted on a ceiling ....................................................................................................... 36
8.3.5 LS18 & GEO S12 vertical array rigidly mounted on a ceiling ....................................................................................... 38
8.3.6 LS18 and GEO S12 vertical array cable mounted on a ceiling ..................................................................................... 41
8.3.7 GEO S12 horizontal array rigidly mounted on a ceiling ................................................................................................. 42
8.3.8 GEO S12 horizontal array cable mounted on a ceiling .................................................................................................... 44
8.4 GEO S12 IN TOURING APPLICATIONS ................................................................................................................................................... 45
8.4.1 Touring Accessories ....................................................................................................................................................................... 45
8.4.2 Single GEO S12 on speaker stand or on LS18 horizontally ............................................................................................ 46
8.4.3 Single GEO S12 flown vertically ................................................................................................................................................ 48
CONTENTS Page 7/103
8.4.4 Single GEO S12 flown horizontally .......................................................................................................................................... 49
8.4.5 Two GEO S12 on wind-up stand ............................................................................................................................................... 50
8.4.6 Two GEO S12 flown horizontally.............................................................................................................................................. 54
8.4.7 Two or more GEO S12 flown vertically .................................................................................................................................. 55
8.4.8 LS18 and three or more GEO S12 flown horizontally ...................................................................................................... 58
8.4.9 Ground stacked LS18 and GEO S1210 .................................................................................................................................... 63
8.5 TESTING AND MAINTENANCE OF THE SYSTEM .................................................................................................................................... 68
9 SYSTEM ALIGNMENT GUIDELINES ......................................................................................................................................69
9.1 GEO S12 VERTICAL CLUSTER DESIGN ................................................................................................................................................. 69
9.2 STACKED LS18S AND FLOWN GEO S12 ............................................................................................................................................. 69
................................................................................................................................................................................................................................. 69
9.3 DRIVING THE LS18S FROM THE AUX SEND......................................................................................................................................... 70
9.4 RECOMMENDED INSTALLATION TOOLS AND EQUIPMENT .................................................................................................................. 71
10 GEO S12 – LS18S SYSTEM CHECK LIST ..............................................................................................................................72
10.1 ARE THE SPEAKERS PROPERLY CONNECTED AND ANGLED ? .............................................................................................................. 72
10.2 FINAL PRE-SOUND CHECK CHECK ......................................................................................................................................................... 72
11 TECHNICAL SPECIFICATIONS ...............................................................................................................................................73
11.1 LS18 SUBWOOFER ................................................................................................................................................................................... 73
11.1.1 System specifications .............................................................................................................................................................. 73
11.1.2 Dimensions .................................................................................................................................................................................. 74
11.2 GEO S1230 MODULE ............................................................................................................................................................................. 75
11.2.1 System specifications .............................................................................................................................................................. 75
11.2.2 Dimensions .................................................................................................................................................................................. 76
11.2.3 Diagrams ..................................................................................................................................................................................... 76
11.3 GEO S1210 MODULE ............................................................................................................................................................................. 77
11.3.1 System specifications .............................................................................................................................................................. 77
11.3.2 Dimensions .................................................................................................................................................................................. 78
11.3.3 Diagrams ..................................................................................................................................................................................... 78
11.4 GEO S12 TOURING APPLICATIONS ACCESSORIES .............................................................................................................................. 79
11.4.1 GPT- BUMPER ............................................................................................................................................................................ 79
11.4.2 LS18 Rigging Plates ................................................................................................................................................................. 80
11.4.3 GEO S12 Rigging Plates .......................................................................................................................................................... 81
11.4.4 Tension Mode Link Bars for GPT-XBOW .......................................................................................................................... 82
11.4.5 Lifting Ring ................................................................................................................................................................................. 83
11.4.6 Truss hook for GPT-PSBRK or GPT-SSBRK ..................................................................................................................... 84
11.4.7 Truss hook for single vertical GEO S12 ............................................................................................................................ 85
11.4.8 “U” Bracket for single vertical GEO S12 ........................................................................................................................... 86
11.4.9 U” Bracket for two vertical GEO S12................................................................................................................................. 87
11.4.10 Ground Stacking Device for up to 6 GEO S1210 ........................................................................................................... 88
11.5 GEO S12 FIXED INSTALLATIONS ACCESSORIES ................................................................................................................................. 89
11.5.1 LS18 & GEO S12 Bumper (VNI-BUMPER) ....................................................................................................................... 89
11.5.2 LS18 Counter Plate (LSI-CPLA) ........................................................................................................................................... 90
11.5.3 GEO S12 Counter Plate (VNI-CPLA) .................................................................................................................................. 91
11.5.4 LS18 & GEO S12 Connecting Plate 1 (VNI-ANPL1) ..................................................................................................... 92
11.5.5 GEO S12 Connecting Plate 2 (VNI-ANPL2) ..................................................................................................................... 93
11.5.6 GEO S12 Connecting Plate 3 (VNI-ANPL3) ..................................................................................................................... 94
11.5.7 Single GEO S12 “U” Bracket .................................................................................................................................................. 95
11.5.8 “L” Bracket for cable suspension ........................................................................................................................................ 96
11.5.9 “U” Bracket for rigid suspension......................................................................................................................................... 97
11.5.10 GEO S12 Push-Pins (04VXT-BL820) .................................................................................................................................. 98
12 GEO S12 SERIES PARTS & ACCESSORIES LIST ................................................................................................................99
12.1 MODULES & CONTROL ELECTRONICS LIST .......................................................................................................................................... 99
12.2 ACCESSORIES LIST .................................................................................................................................................................................... 99
13 USER NOTES ............................................................................................................................................................................. 102
Page 8/103 INTRODUCTION
1 INTRODUCTION
Thank you for selecting a NEXO GEO S12 Series Tangent Array System. This manual is intended to
provide you with necessary and useful information about your GEO S12 System, which includes the
following products:
GEO S1230 is a 30° Tangent
Array Module. It comprises 1x12”
(30cm) Neodynium 16 ohms
LF/MF driver and 1x3” voice coil,
1.4” Throat 16 Ohm HF Driver
loaded by a 28.5° Hyperboloid
Reflective Wavesource™.
GEO S1210 is a 10° Tangent
Array Module. It comprises 1x12”
(30cm) Neodynium 16 ohms
LF/MF driver and 1x3” voice coil,
1.4” Throat 16 Ohm HF Driver
loaded by a 5° Hyperboloid
Reflective Wavesource™.
LS18 is Geo S12 dedicated
subwoofer. It comprises 1x18’’
(46cm) long excursion driver, and
features very high efficiency as
well as high acoustic output.
LS18 has fittings for transporting,
flying and pole standing.
LS18e is identical to LS18, with
the exception that it has none of
the fittings described above. It is
intended to be set on the floor in
fix installations.
INTRODUCTION Page 9/103
GEO S12 Accessory Range. a full range of accessories that provides safe, flexible and
simple means of installing Geo S12 Tangent Arrays in fixed installation as well as in
touring applications.
As for all NEXO systems, GEO S12s are controlled, powered and monitored by dedicated NEXO
TDControllers:
NXAMP4x1 and NXAMP 4x4 are Powered Digital Controllers, providing full control and
amplification for RS15 in multiple configurations. Both devices feature 4 analogue inputs
and 4 speaker outputs. When equipped with optional card, 4 digital inputs in
EthersoundTM or DanteTM digital audio network format as well as remote control for all
units in the network become available.
For a complete description of these controllers, please refer to User Manuals. NXAMP DSP algorithms
and parameters are fixed in software and updated regularly: Please consult the NEXO web site
(www.nexo.fr) for the latest software releases.
Page 10/103 INTRODUCTION
NS-1 simulation software assists in the design and implementation of vertical tangent
GEO arrays. Please consult the NEXO web site (www.NEXO.fr or www.NEXO-sa.com)
for the latest software releases.
Please devote your time and attention to reading this manual. A comprehensive understanding of GEO
theory, tangent arrays and specific features of GEO S12 and LS18 will help you to operate your system
at its full potential.
GEO S12 GENERAL SET-UP INSTRUCTIONS Page 11/103
2 GEO S12 GENERAL SET-UP INSTRUCTIONS
2.1 Speaker connection
GEO S12 and LS18 is connected with Speakon NL4FC plugs (not supplied). A wiring diagram is printed
on the connection panel located on the back of each cabinet. The 4 pins of the 2 Speakon sockets
identified in / out are connected in parallel within the enclosure.
Either connector can be used to connect amplifier or to link to an additional Geo S12 cabinet or to link to
an optional LS18 (if present). Therefore, a single 4-conductor cable can connect two amplifier channels
to various Geo S12 and/or Sub Bass.
2.1.1 GEO S12 connectors
Connectors are wired as follows:
2.1.2 LS18 connector
Connectors are wired as follows:
2.1.3 Configuring Geo S12 for Passive or Active Mode
Remove the six TORX screws that hold the connector panel (figure next page);
Remove the connector panel so that filter WAGO connectors become accessible;
In Passive Mode, connector A (from filter) should be inserted in connector B (PCB
“Passive In”), and Connector D (“Passive Out”) should be connected to speakers via
connector C.
In Active Mode, WAGO Connector A (from filter) should be directly connected into
speakers via connector C (PCB connectors B & D are then unused).
Speakon
Connector
Passive
Mode
Active
Mode
1(-)
Not Connected
Geo S12 LF (-)
1(+)
Not Connected
Geo S12 LF (+)
2(-)
Geo S12 (-)
Geo S12 HF (-)
2(+)
Geo S12 (+)
Geo S12 HF (+)
Speakon
Connector
1(-)
LS18 (-)
1(+)
LS18 (+)
2(-)
Not Connected
2(+)
Not Connected
Page 12/103 GEO S12 GENERAL SET-UP INSTRUCTIONS
2.1.4 Cabling
NEXO recommends the exclusive use of multi-conductor cables to connect the system: the cable kit is
compatible with all the cabinets, and there is no possible confusion between LF, MF and HF sections.
Cable choice consists mainly of selecting cables of the correct sectional dimension (size) in relation to
the load resistance and the cable length. Too small a cable section will increase both its serial
resistance and its capacitance; this reduces the electrical power delivered to the loudspeaker and can
also induce response (damping factor) variations.
For a serial resistance less or equal to 4% of the load impedance (damping factor = 25), the maximum
cable length is given by:
Lmax = Z x S S in mm2, Z in Ohm, Lmax in meters
The table below indicates these values, for 3 common sizes.
Load Impedance ()
2
3
4
6
8
12
16
Cable section
Maximum Length (meters)
1,5 mm² (AWG #14)
3
4.5
6
9
12
18
24
2,5 mm² (AWG #12)
5
7.5
10
15
20
30
40
4 mm² (AWG #10)
8
12
16
24
32
48
64
2.1.5 Example:
GEO S12 has a 16 Ohms nominal impedance in passive mode, so 4x Geo S12 wired in
parallel will present a 16/4 = 4 Ohm load impedance. The maximum acceptable 2x2.5
mm2 (AWG #12) cable length Lmax for such a cluster is 10 meters.
IMPORTANT
Long speaker cables induce capacitive effects – up to hundreds of pF depending on the
quality of the cable - with a low-pass effect on high frequencies. If long speaker cables
must be used, ensure that they do not remain coiled while in use.
GEO S12 GENERAL SET-UP INSTRUCTIONS Page 13/103
CONNECTOR PANEL PASSIVE MODE ACTIVE MODE
B
A
D
C
B
D
A
C
Page 14/103 AMPLIFIER SELECTION FOR USE WITH GEO S12 & LS18
3 AMPLIFIER SELECTION FOR USE WITH GEO S12 & LS18
3.1 GEO S12, LS18 and NXAMP TDControllers
NEXO Powered TDControllers NXAMP 4X1 & 4X4 are integrated solutions for Control and amplification
for all NEXO speaker ranges.
NXAMP4x1 and NXAMP4x4 power capability is listed in the table below:
Mode
4 Channels
Bridge Stereo
NXAMP4x1
4 x 600 Watts / 8 Ohms
4 x 900 Watts / 4 Ohms
4 x 1300 Watts / 2 Ohms
2 x 1800 Watts / 8 Ohms
2 x 2600 Watts / 4 Ohms
NXAMP4x4
4 x 1900 Watts / 8 Ohms
4 x 3300 Watts / 4 Ohms
4 x 4000 Watts / 2 Ohms
2 x 6600 Watts / 8 Ohms
2 x 8000 Watts / 4 Ohms
3.1.1 NXAMP connectors
NXAMP4x1 and NXAMP4x4 rear panels feature:
4 analog inputs / outputs (links) on XLR3 connectors;
4 digital inputs / outputs on RJ45 connectors with optional NX-ES104 card;
4 speaker level outputs on NL4FC connectors.
Figure below shows connectors implementation on the rear panel.
3.1.2 GEO S12, LS18 and NXAMP recommended configurations
Passive Mode
Active Mode
3 x GEO S12
1 channel of NXAMP4x1 in Bridge Stereo Mode
1 channel of NXAMP4x4 in 4 channels mode
2 channels of NXAMP4x1 in Bridge Stereo Mode
2 channels of NXAMP4x4 in 4 channels mode
4 x GEO S12
1 channel of NXAMP4x4 in 4 channels mode
2 channels of NXAMP4x4 in 4 channels mode
2 x LS18
1 channel of NXAMP4x1 in Bridge Stereo Mode
1 channel of NXAMP4x4 in 4 channels mode
GEO S12 SETUPS ON NEXO TD CONTROLLERS Page 15/103
4 GEO S12 SETUPS ON NEXO TD CONTROLLERS
4.1 NXAMP TDControllers
As of today, load 3.15 features the setups listed in below table in the “Nexo configurations” menu.
Keep in mind that the “custom configuration menu” allows to build any combination of NEXO speakers
with
- full phase compatibility from 20 Hz to 20kHz.
- Choice between 85 Hz and 120 Hz X-over point between LS18 and Geo S12.
Please consult www.nexo-sa.com for upgrade releases.
Setup Name
#
CH1
CH2
CH3
CH4
S1210 AC WB
LF(1-3) HF(2-4)
50
S1210 LF 50-1k
S1210 HF 1k-20k
S1210 LF 50-1k
S1210 HF 1k-20k
S1210 PA WB
4 Channels
53
S1210 PA 50-20k
S1210 PA 50-20k
S1210 PA 50-20k
S1210 PA 50-20k
S1210 PA XO (2-4)
LS18 (1-3)
55
LS18 35-85
S1210 PA 85-20k
LS18 35-85
S1210 PA 85-20k
S1230 AC WB
LF(1-3) HF(2-4)
56
S1230 LF 50-1k
S1230 HF 1k-20k
S1230 LF 50-1k
S1230 HF 1k-20k
S1230 PA WB
4 Channels
59
S1230 PA 50-20k
S1230 PA 50-20k
S1230 PA 50-20k
S1230 PA 50-20k
S1230 PA XO (2-4)
LS18 (1-3)
60
LS18 35-85
S1230 PA 85-20k
LS18 35-85
S1230 PA 85-20k
Page 16/103 CONNECTION DIAGRAMS
5 CONNECTION DIAGRAMS
5.1 GEO S12 / NXAMP4x1 (Bridge Stereo – S12 in Passive mode)
CONNECTION DIAGRAMS Page 17/103
5.2 GEO S12 / NXAMP4x1 (Bridge Stereo – S12 in Active mode)
Page 18/103 CONNECTION DIAGRAMS
5.3 LS18 / NXAMP4x1 (Bridge Stereo)
CONNECTION DIAGRAMS Page 19/103
5.4 LS18 & Geo S12 / NXAMP4x1 (Bridge Stereo – S12 in Passive mode)
Page 20/103 CONNECTION DIAGRAMS
5.5 GEO S12 / NXAMP4x4 (4 Channels – S12 in Passive mode)
CONNECTION DIAGRAMS Page 21/103
5.6 GEO S12 / NXAMP4x4 (S12 in Stereo Active mode)
Page 22/103 CONNECTION DIAGRAMS
5.7 LS18 / NXAMP4x4 (4 channels)
CONNECTION DIAGRAMS Page 23/103
5.8 LS18 & GEO S12 NXAMP4x4 (S12 in Passive Mode)
Page 24/103 NS-1 SIMULATION SOFTWARE
6 NS-1 SIMULATION SOFTWARE
NS-1 software is a R&D simulation tool derived application. It processes measured speaker data with
complex mathematical algorithms to assist the user in optimizing system design. Due to the complexity
of the interaction of multiple cabinets, it is simply not possible to reliably design curved vertical arrays
without using the processing power of a computer to predict the optimum array structure for a given
audience geometry. The design logic is far more complex than looking at a section drawing of the
venue, measuring the overall angle needed to cover the audience from the cluster location, and dividing
by 10 degrees to determine the required amount number of GEO S1210 cabinets.
NS-1 is an easy to use tool that allows to shape the energy leaving the cluster to fit the audience. It
predicts pressure levels radiated from the system to ensure enough cabinets are provided for the
application, as well as mechanical constraints for safe flown systems.
In addition, it provides mechanical information for all clusters in agreement with Structural Analysis
Reports (available in the Help section): dimensions, weight, gravity center position, forces, moments,
working load and safety factor.
Geo S12 Structural Analysis Reports have been validated by German Certification Organization
RWTUV systems GmbH.
NS-1 installation package includes all NEXO User Manuals, Structural Analysis Reports and Certificates
PDF files (which can be found in the last section of User Manuals).
NS-1 is a freeware available on www.nexo-sa.com
IMPORTANT
Never install a GEO S12 & LS18 cluster without checking its acoustical performances
and mechanical safety in NS-1 prior to installation.
Any question or bug report please contact technical@nexo.fr
NS-1 GEO S12 ACOUSTIC PAGE
CONFIGURABLE DIRECTIVITY DEVICE Page 25/103
7 CONFIGURABLE DIRECTIVITY DEVICE
The GEO Wavesource controls dispersion of acoustic energy using an hyperboloid acoustical reflector
in the “coupling plane” (the vertical plane of a curved vertical tangent array) and a diffraction slot in the
“non-coupling plane” (the horizontal plane of a curved vertical tangent array). The patented
Configurable Directivity Device consists of bolt-on flanges that alter the diffraction slot’s exit flare rate.
7.1 Installing & removing GEO’s Configurable Directivity flanges
GEO S12 are shipped in the 80° dispersion configuration;
120° flanges is an optional accessory.
To change dispersion in the non-coupling plane to 120°:
Remove the front grill (drawings below);
Remove the three TORX (5x25) screws per flange on each side of the GEO Waveguide
(drawings below);
Install the 120° flanges with the six TORX screws
Re-install the grid, being careful that the NEXO logo must be on the 12” loudspeaker
side.
REMOVING THE GRILL
REMOVING THE SCREWS REPLACING THE FLANGES
Page 26/103 CONFIGURABLE DIRECTIVITY DEVICE
7.2 When & where to use Configurable Directivity flanges
The diagrams show audience area coverage for a stereo system. While the GEO cluster will deliver
even SPL from the front to the rear of this audience area, there are “holes” near the front in the centre
and at the outside edges. We cannot fill the outside coverage gaps without enlarging the centre gap,
and vice versa (left figure below).
If 120° Configurable Directivity Devices are installed at the bottom cabinet of the clusters, coverage will
look more like the pattern in right figure below.
-6dB coverage, all GEO S12 in 80° configuration
-6dB coverage, bottom GEO S12 in 120° configuration
In curved vertical arrays, the 120° Configurable Directivity Device can be used:
On the bottom row of curved vertical arrays, to fill in coverage gaps in the front rows.
On all rows of curved vertical arrays, in cases where 120° of horizontal coverage is
preferred to 80°.
Figure below shows isocontour coverage for 80° and 120° configurations.
80° AND 120° CONFIGURATIONS ISOCONTOUR COVERAGE
GEO S12 HARDWARE SETUP PROCEDURE Page 27/103
8 GEO S12 HARDWARE SETUP PROCEDURE
Before proceeding with assembly of GEO S12 & LS18 arrays, please ensure that the components are
present and undamaged. A component list is appended to this manual. In the event of any shortage,
please contact your supplier.
For maximum efficiency the GEO S12 & LS18 rigging system requires three experienced persons for
set-up: typically one motor hoist operator, and one operator per side of the array. Good synchronisation
and crosscheck between the operators are key elements for a reliable and safe set-up.
8.1 SAFETY FIRST
GEO S12 & LS18 Rigging System structural computations and related documents are available in NS-1
or at Nexo (info@nexo.fr) upon request.
We include this section to remind you of safe practice when flying the GEO S12 & LS18 system. Please
read it carefully. However, user must always apply his or her knowledge, experience and common
sense. If in any doubt, seek advice from your supplier or NEXO agent.
This manual offers guidance only for GEO S12 & LS18 loudspeaker systems. References in this
manual to other rigging equipment such as motor hoists, steels, shackles etc. are made to clarify the
description of rigging procedures. The user must ensure that operators are properly trained by other
agencies in the use of these items.
The GEO S12 & LS18 Rigging System has been optimised for the deployment of curved vertical or
horizontal tangent arrays of GEO S12 & LS18 loudspeakers. Angle adjustment between cabinets has
been limited to specific settings to ensure correct acoustic coupling.
The GEO S12 & LS18 Rigging System is a professional precision tool set, and should be handled with
extreme care. Only persons who are fully conversant with the operation of the GEO S12 & LS18
Rigging System and provided with suitable safety equipment should deploy GEO Arrays. Misuse of the
GEO S12 & LS18 Rigging System could lead to dangerous consequences.
Used and maintained correctly, the GEO S12 & LS18 Rigging System will give many years of reliable
service in portable systems. Please take the time to read and understand this manual. Always use NS-1
to determine the optimum angle settings for a particular venue, hang point and curved vertical GEO S12
& LS18 cluster. Applied forces and moments are strongly cabinet quantity and angle configuration
dependent. Cluster configuration must be implemented and validated in NS-1 prior to installation.
8.1.1 Flown Systems Safety
Always inspect all the rigging components and cabinets for damage before assembly.
Pay special attention to the lifting points, and safety clips. If you suspect that any of the
components are damaged or defective, DO NOT USE THE AFFECTED PARTS.
Contact your supplier for replacements.
Read this manual carefully. Also be familiar with the manuals and safe working
procedures for any ancillary equipment that will be used with the GEO S12 & LS18
Rigging System.
Applied forces and moments are strongly cabinet quantity and angle configuration
dependent. Cluster configuration must be implemented and validated in NS-1 prior to
installation.
Ensure that all local and National regulations regarding the safety and operation of flying
equipment are understood and adhered to. Information on these regulations can usually
be obtained from Local Government Offices.
Page 28/103 GEO S12 HARDWARE SETUP PROCEDURE
When deploying a GEO S12 & LS18 system always wear protective headwear, footwear
and eye protection.
Do not allow inexperienced persons to handle a GEO S12 & LS18 system. Installation
personnel should be trained in loudspeaker flying techniques and should be fully
conversant with this manual.
Ensure that motor hoists, hoist control systems and ancillary rigging components are
currently certified as safe and that they pass a visual inspection prior to use.
Ensure that public and personnel are not allowed to pass beneath the system during the
installation process. The work area should be isolated from public access.
Never leave the system unattended during the installation process.
Do not place any object, no matter how small or light, on top of the system during the
installation procedure. The object may fall when the system is flown and is likely to
cause injury.
Secondary safety steels must be installed once the system has been flown to the
operating height. Secondary steels must be fitted irrespective of requirements of the
local safety standards applicable to the territory.
Ensure that the system is secure and prevented from pivoting around the motor hoist.
Avoid any form of excessive dynamic loading to the assembly (structural computations
on GEO S12 & LS18 Rigging System are based on a 1/1.2 factor for hoist or motor
acceleration).
NEVER attach any item to the GEO S12 & LS18 system other than the GEO S12 &
LS18 accessories.
When flying outdoor systems ensure that the system is not exposed to excessive wind
or snow loads and is protected from rainfall.
The GEO S12 & LS18 Rigging System requires regular inspection and testing by a
competent test centre. NEXO recommend that the system is load tested and certified
annually or more frequently if local regulations require.
When de-rigging the system ensure that the same duty of care is given to the procedure
as for the installation. Pack GEO S12 & LS18 components carefully to prevent damage
in transit.
8.1.2 Ground Stacking Safety
Statistically, many more injuries occur due to unstable ground stacked PA systems than those
associated with flown systems. There are several reasons for this fact, however the message is clear:
Always survey the supporting structure upon which a ground stack is to be built. Always
look beneath PA wings to inspect the deck support and if necessary ask for the stage
scrims and dressings be removed to allow access.
If the stage surface slopes, as it does in some theatres, ensure that the system is
prevented from sliding forwards due to vibration. This may require the fitting of timber
battens to the stage floor.
For outdoor systems ensure that that the system is protected from wind forces which
might cause the ground stack to become unstable. Wind forces can be huge, especially
upon large systems, and should never be underestimated. Observe meteorological
forecasts, calculate the “worst case” effect upon the system prior to erection and ensure
that the system is secured appropriately.
Take care when stacking cabinets. Always employ safe lifting procedures and never
attempt to build stacks without sufficient personnel and equipment.
GEO S12 HARDWARE SETUP PROCEDURE Page 29/103
Never allow anyone, whether operators, artists or members of the public to climb onto a
ground stacked PA system. Anyone who needs to climb over 2m (6 ft) high should be
fitted with suitable safely equipment including a clip-on harness. Please refer to local
Health and Safety legislation in your territory. Your dealer can help with advice on access
to this information.
Apply the same attention to all safety matters when de-stacking systems.
Be aware that safety procedures are as important in the truck and in the warehouse as
they are at the venue.
8.1.3 Contacts
Correct training is fundamental to safe practise when working with loudspeakers flying systems. NEXO
recommend that users contact local industry associations for information on specialist course.
Information for International training agencies can be obtained by contacting either:
The Production Services Association
(PSA),
School Passage,
Kingston-upon-Thames,
KT1 SDU Surrey,
ENGLAND
Telephone: +44 (0) 181 392 0180
Rigstar Training and Testing Center
82 Industrial Dr. Unit 4
Northampton, Massachusetts
01060 U.S.A.
Phone: 413-585-9869 -- Fax: 413-585-
9872
school@rigstar.com
ESTA
Entertainment Services & Technology Association
875 Sixth Avenue, Suite 1005
NEW YORK, NY 10001 USA
Phone: 212-244-1505 – Fax: 212-244-1502
info@esta.org - www.esta.org
Page 30/103 GEO S12 HARDWARE SETUP PROCEDURE
8.2 General Description
GEO S1230 GEO S1210
GEO S1230, GEO S1210 and LS18 incorporate two connecting plates (one per side) on which a
comprehensive range of accessories can be mounted.
GEO S12 CONNECTING PLATES
LS18 CONNECTING PLATES
There are two families of accessories:
fixed installation accessories, which are designed to be screwed on the connecting
plates;
touring accessories, which can be installed or removed with a quick connecting system.
Oblong holes for Touring Applications Accessories
Tapped holes for Fixed Installation Accessories
GEO S12 HARDWARE SETUP PROCEDURE Page 31/103
8.2.1 Described configurations
FIXED INSTALLATIONS
TOURING APPLICATIONS
SECTION 8.3.2
SECTION 8.3.2
SECTION 8.3.3
SECTION 8.3.4
SECTION 8.3.7
SECTION 8.3.5
SECTION 8.4.2
SECTION 8.4.6
SECTION 8.4.4
SECTION 8.4.7
SECTION 8.4.3
SECTION 8.4.9
SECTION 8.4.5
SECTION 8.4.8
Page 32/103 GEO S12 HARDWARE SETUP PROCEDURE
8.2.2 WARNINGS ON GEO S12 ACCESSORIES
WARNING 1
All GEO S12 & LS18 Accessories are specifically rated in agreement with structural
computations.
Never use other accessories ‒ including push-pins - when assembling GEO S12 & LS18
cabinets than the ones provided by NEXO: NEXO will decline responsibility over the
entire GEO S12 & lS18 accessory range if any component is purchased from different
supplier.
WARNING 2
For SAFETY reasons, following first generation accessories:
- GEOS12-XBOW
- GEOS12-TCBRK
- GEOS12-SSBRK
- GEOS12-PSBRK
- GEOS12-TTC
Have been recalled in August 2007 and MUST NO LONGER BE USED
These accessories have been replaced by:
- GPT-XBOW-V2
- GPT-TCBRK-V2
- GPT-SSBRK-V2
- GPT-PSBRK-V2
- GPT-TTC-V2
Please contact your local distributor if any doubt in relation the GEO S12 & LS18
accessories you are using.
WARNING 3
All GEO S12 accessories have been designed so that cabinets are arrayed in the
acoustic coupling plane (adjacent waveguides as shown in figures below).
GEO S12 assemblies in the non -coupling plane ‒ as shown in figure below- are
UNSAFE and STRICTLY PROHIBITED.
YES YES NO
GEO S12 HARDWARE SETUP PROCEDURE Page 33/103
8.3 GEO S12 in fixed installations
8.3.1 Fixed installation Accessories and kits
Accessories are:
Bumper for Geo S12 & LS18 (VNI-BUMPER1)
“U” Bracket (VNI-UBRK12)
“L” Bracket for cable suspension (VNI-LBRK)
“U” Bracket for rigid suspension (VNI-ABRK)
Connecting Plates / range : 0.20° - 3.15° (VNI-ANPL1)
Connecting Plates / range : 5.00° - 10.0° (VNI-ANPL2)
Connecting Plates / range : 16.0° - 30.0° (VNI-ANPL3)
Counter-Plates for LS18 (LSI-CPLA)
Counter Plates for Geo S12 (VNI-CPLA)
Please refer to section 13.4 of this manual for more information of above references.
IMPORTANT
In order to prevent screws from getting loose in fixed installations, use blocking liquid
LOCTITETM 243 or equivalent for all screws used with GEO S12 & LS18 fixed installation
accessories.
LOCTITETM 243 is available at NEXO or at your local distributor upon request.
VNI-BUMPER VNI-UBRK12 VNI-LBRK VNI-ABRK
VNI-ANPL1 VNI-ANPL2 VNI-ANPL3
Page 34/103 GEO S12 HARDWARE SETUP PROCEDURE
8.3.2 Single GEO S12 rigidly mounted on a wall or a ceiling (vertical or horizontal)
Required items
1 x GEOS12-UBRK (allows all angles to be implemented)
4 x 12mm diameter screws (not provided)
IMPORTANT
Ensure that the surface – wall or ceiling – is strong enough to hold GEO S12 weight and
that the for screws 12mm diameter and corresponding plugs required to fix the “U”
bracket on the wall or under the ceiling are properly dimensioned.
Procedure
For screws 12mm diameter (not provided) are required to secure the “U” Bracket on the
wall or ceiling;
Remove the four TORX screws holding connector plates on both sides of GEO S12;
Position the GEO S12 inside the “U” Bracket to desired angle; “U” bracket oblong holes
must be properly aligned with panels holes;
Apply Loctite 243 or equivalent to the eight screws and washers from VNI-UBRK12 kit;
Connect “U” bracket to cabinet with these screws.
GEO S12 HARDWARE SETUP PROCEDURE Page 35/103
8.3.3 Single GEO S12 cable mounted on a wall or a ceiling (vertical or horizontal)
Required items
1 or 2 x VNI-LBRK (allows cable suspension, holes for cable suspension are 10mm
diameter);
2 or 4 slings and corresponding shackles (not provided)
IMPORTANT
Ensure that the ceiling is strong enough to hold GEO S12 weight and that the cable
suspension system required to install the cabinet under the ceiling is properly
dimensioned.
Procedure
Vertical
Remove the four TORX screws holding
connector plate on upper side of GEO S12;
Remove the connector plate from Geo S12;
Apply Loctite 243 or equivalent to the 4
shoulder screws from VNI-LBRK;
Position external plate from VNI-LBRK kit
and secure it using the 2 of the 4 shoulder
screws;
Position “L” bracket from VNI-LBRK kit, and
secure it to the cabinet using the 2 remaining
shoulder screws;
Slings and shackles (not provided) are
required to secure the cluster under the
ceiling;
Horizontal
Remove the four TORX screws holding
connector plates on both side of GEO S12;
Remove the connector plates from Geo S12;
Apply Loctite 243 or equivalent to the 4
shoulder screws from VNI-LBRK;
Position external plates from VNI-LBRK kits
and secure them using the shoulder screws;
Position “L” brackets from VNI-LBRK kits,
and secure them to the cabinet using the 4
remaining shoulder screws;
Slings and shackles (not provided) are
required to secure the cluster under the
ceiling;
Page 36/103 GEO S12 HARDWARE SETUP PROCEDURE
8.3.4 GEO S12 vertical array rigidly mounted on a ceiling
Required items
1 x VNI-BUMPER (allows +/-5° bumper tilt when installed below a flat surface; if higher
bumper tilt is required, surface will have to be defined accordingly) ;
(N-1) x VNI-ANPL for a N x GEO S12 array (ANPL1 ranges from 0.2° to 3.15°, ANPL2
ranges from 5° to 10°, ANPL3 ranges from 16° to 30°)
N x VNI-CPLA for a N x GEO S12 array
Four 12mm diameter screws (not provided)
IMPORTANT
Ensure that the ceiling is strong enough to hold GEO S12 cluster weight and that the
four screws 12mm diameter and corresponding plugs required to fix the bumper under
the ceiling are properly dimensioned.
Procedure
(1) Set all GEO S12 sideways according to cluster configuration;
(2) Remove the four TORX screws holding connector plates on upper side of all GEO
S12’s;
(3) Remove the connector plates from all Geo S12’s;
(4) Position bottom counter-plates, angle plates and top counter-plates from VNI-ANPL
and VNI-CPLA to required inter-cabinet angle value between cabinets upper sides;
(5) Apply Loctite 243 or equivalent to shoulder screws from VNI-CPLA kits;
(6) Screw shoulder screws so that all plates and cabinets are tightened together;
(7) Flip the cluster upside down to access connector plates located on the down side;
(8) Repeat all above steps from #2 to #6;
GEO S12 HARDWARE SETUP PROCEDURE Page 37/103
(9) Apply Loctite 243 or equivalent to four shoulder screws from the last VNI-CPLA kit;
(10) Position the VNI-BUMPER bumper to required angle position and use the four
shoulder screws to connect it the bumper to the top cabinet;
(11) Flip GEO S12 cluster by 90° so that it is ready to be positioned under the ceiling;
(12) Four screws 12mm diameter (not provided) are required to secure the bumper
under the ceiling.
Page 38/103 GEO S12 HARDWARE SETUP PROCEDURE
8.3.5 LS18 & GEO S12 vertical array rigidly mounted on a ceiling
Required items
1 x VNI-BUMPER (allows +/-5° bumper tilt when installed below a flat surface; if higher
bumper tilt is required, surface will have to be defined accordingly) ;
(M-1) x VNI-ANPL1 for M x LS18
M x LSI-CPLA counter-plates for M x LS18
N x VNI-ANPL for a N x GEO S12 (ANPL1 ranges from 0.2° to 3.15°, ANPL2 ranges
from 5° to 10°, ANPL3 ranges from 16° to 30°)
N x LSI-CPLA counter-plates for N x GEO S12
Four 12mm diameter screws (not provided)
IMPORTANT
Ensure that the ceiling is strong enough to hold LS18 & GEO S12 cluster weight and
that the four screws 12mm diameter and corresponding plugs required to fix the
bumper under the ceiling are properly dimensioned.
Procedure
(1) Set LS18s and GEO S12s sideways according to cluster configuration;
(2) Remove the TORX screws holding connector plates on upper side of all LS18s and
GEO S12s;
(3) Remove the connector plates from all LS18 and Geo S12s;
(4) Remove the 4 locking screws from LS18 side wood panel (see figure below), these
are no longer to be used;
GEO S12 HARDWARE SETUP PROCEDURE Page 39/103
(5) Apply Loctite 243 or equivalent to the screws that attach the LS18 connector plate to
the cabinet, and reinstall the LS18 connector plates (see figure below left);
(6) Position Geo S12 bottom counter-plates (see figure below left);
(7) Position VNI-ANPL1 angle plates (set at 0.2°) and LSI-CPLA top counter-plates on
LS18 upper sides according to figure below right ;
(8) Position angle plates and top counter-plates from VNI-ANPL and VNI-CPLA to
required GEO S12 inter-cabinet angle value between GEO S12 upper sides according
to figure below right;
(9) Apply Loctite 243 or equivalent to shoulder screws from LSI-CPLA and VNI-CPLA
kits;
(10) Screw all shoulder screws so that all plates and cabinets are tightened together;
(11) Flip the cluster upside down to access connector plates located on the down side;
(12) Repeat all above steps from #2 to #10;
(13) Position the VNI-BUMPER bumper to required angle position and use the four
shoulder screws to connect it the bumper to the top cabinet;
Page 40/103 GEO S12 HARDWARE SETUP PROCEDURE
(11) Flip cluster by 90° so that it is ready to be positioned under the ceiling;
(12) Four screws 12mm diameter (not provided) are required to secure the bumper
under the ceiling.
GEO S12 HARDWARE SETUP PROCEDURE Page 41/103
8.3.6 LS18 and GEO S12 vertical array cable mounted on a ceiling
Required items
As in 2 sections above, plus
2 x VNI-LBRK (allows cable suspension for bumper, holes for cable suspension are
10mm diameter);
4 slings and shackles (not provided)
IMPORTANT
Ensure that the ceiling is strong enough to hold LS18 & GEO S12 cluster weight and
that the cables suspension system required fixing the bumper under the ceiling is
properly dimensioned.
Procedure
Connect the bumper and the two “L” brackets using the screws, washers and bolts
provided in the VNI-LBRK kit;
Proceed as in preceding sections;
4 slings and 4 shackle (not provided) are required to secure the cluster under the ceiling;
Page 42/103 GEO S12 HARDWARE SETUP PROCEDURE
8.3.7 GEO S12 horizontal array rigidly mounted on a ceiling
Required items
2 x VNI-ABRK (allows rigid ceiling suspension for horizontal arrays)
(N-1) x VNI-ANPL for a N x GEO S12 array (ANPL1 ranges from 0.2° to 3.15°, ANPL2
ranges from 5° to 10°, ANPL3 ranges from 16° to 30°)
N x VNI-CPLA for N x GEO S12 array
Four 12mm diameter screws (not provided)
IMPORTANT
Ensure that the ceiling is strong enough to hold GEO S12 cluster weight and that the
four screws 12mm diameter and corresponding plugs required to fix the “L” brackets
under the ceiling are properly dimensioned.
Procedure
(1) Set all GEO S12 side by side;
(2) Remove the four TORX screws holding connector plates on upper side of all GEO
S12’s;
(3) Remove the connector plates from all Geo S12’s;
(4) Position bottom external plates, angle plates and top external plate from VNI-ANPL
and VNI-CPLA kits to required inter-cabinet angle value between cabinets upper sides;
(5) Apply Loctite 243 or equivalent to shoulder screws from VNI-CPLA kits;
(6) Screw all shoulder screws so that all plates and cabinets are tightened together;
GEO S12 HARDWARE SETUP PROCEDURE Page 43/103
(7) Flip the cluster upside down to access connector plates located on the down side;
(8) Repeat all above steps from #2 to #6;
(9) Position the two “U” brackets from VNI-ABRK kits on the outer cabinets next the
angle plates, and tight them to the cabinets using the shoulder screws provided with
these kits (using Loctite 243 or equivalent);
(10) Four screws 12mm diameter (not provided) are required to secure the “U” brackets
under the ceiling;
Page 44/103 GEO S12 HARDWARE SETUP PROCEDURE
8.3.8 GEO S12 horizontal array cable mounted on a ceiling
Required items
2 x VNI-LBRK (allows cable suspension for horizontal arrays, holes for cable suspension
are 10mm diameter);
(N-1) x VNI-ANPL for a N x GEO S12 array (ANPL1 ranges from 0.2° to 3.15°, ANPL2
ranges from 5° to 10°, ANPL3 ranges from 16° to 30°);
N x VNI-CPLA for N x GEO S12 array;
4 slings and 4 shackles (not provided).
IMPORTANT
Ensure that the ceiling is strong enough to hold GEO S12 cluster weight and that the
cables suspension system required fixing the cluster under the ceiling is properly
dimensioned.
Procedure
Proceed as in above section, VNI-LBRK being positioned on the outer cabinets instead
of VNI-ABRK.
4 slings and 4 shackle (not provided) are required to secure the cluster under the ceiling;
GEO S12 HARDWARE SETUP PROCEDURE Page 45/103
8.4 GEO S12 in touring applications
8.4.1 Touring Accessories
Accessories are :
Bumper (GPT-BUMPER)
Geo S12 Rigging Plates (GPT-XBOW)
LS18 rigging plates (LST-XBOW)
Tension Mode Link Bars for GPT-XBOW (GPT-TLB)
Lifting Ring for GPT-SSBRK, GPT-PSBRK or VNT-TTC (VNT-XHBRK)
Truss hook for GPT-SSBRK, GPT-PSBRK or VNT-TTC (VNT-TCBRK)
“U” Bracket for single horizontal GEO S12 on pole stand, lifting ring or truss hook (GPT-
SSBRK)
U” Bracket for two horizontal GEO S12 on pole stand, lifting ring or truss hook (GPT-
PSBRK)
Flying Bar for single vertical GEO S12 (VNT-TTC)
Ground Stacking device for up to 6 GEOS1210 (GPT-GSTK)
Please refer to section 13.3 of this manual for more information of above references.
GPT- BUMPER GPT-XBOW
GPT-TLB VNT-XHBRK VNT-TCBRK
GPT-SSBRK GPT-PSBRK
VNT-TTC GPT-GSTK
Page 46/103 GEO S12 HARDWARE SETUP PROCEDURE
8.4.2 Single GEO S12 on speaker stand or on LS18 horizontally
Required items
1 x “U” Bracket for single horizontal GEO S12 (GPT-SSBRK);
1 x Speaker stand diameter 35mm (K&M 213 or equivalent);
Or NEXO PS pole stand (VXT-PLSTD) for mounting on top of LS18
IMPORTANT (SPEAKER STAND)
- Speaker stand must be rated for assembly weight (40kg rated load min);
- Speaker stand must always be installed on a horizontal surface;
- Stand height and footprint must be defined to prevent assembly from collapsing;
- Ensure that public is not allowed within a safety area which radius is equal or higher
than assembly height.
IMPORTANT (LS18 POLE STAND)
- NEXO PLSTD pole stand only should be used for mounting on top of NEXO LS18
- LS18 must always be installed on a horizontal surface;
- Ensure that public is not allowed within a safety area which radius is equal or higher
than assembly height.
Procedure
Slide GPT-SSBRK side plates into GEO S12 connecting plate oblong holes;
Lock safety pins into GEO S12 connecting plate;
IMPORTANT
Ensure that safety pins are properly locked into GEO S12 connecting panels.
Position “U” bracket over these side plates; align centre holes;
Insert adjustment handles, adjust vertical angle and tight the handles to prevent GEO
S12 from rotating around “U” bracket;
Lift assembly on speaker stand or on LS18 with PLSTD pole stand.
GEO S12 HARDWARE SETUP PROCEDURE Page 47/103
Page 48/103 GEO S12 HARDWARE SETUP PROCEDURE
8.4.3 Single GEO S12 flown vertically
Required items
1 x Flying Bar for single vertical GEO S12 (VNT-TTC)
1 x Lifting Ring (VNT-XHBRK)
Or 1 x Truss hook (VNT-TCBRK)
IMPORTANT
Ensure that truss suspension point is strong enough to hold GEO S12 weight.
Procedure
Slide flying bar VNT-TTC into GEO S12 connecting plate oblong holes;
Lock safety pin into GEO S12 connecting plate;
IMPORTANT
Ensure that safety pin is properly locked into GEO S12 connecting panel.
Cable suspension:
Connect lifting ring VNT-XHBRK to flying bar by inserting 8x45 quick release pin in
required holes for proper vertical aiming;
Ensure lifting ring is properly locked to flying bar;
Connect assembly to suspension point with sling and shackle (not provided).
Truss suspension
Connect truss hook VNT-TCBRK to flying bar by inserting 8x45 quick release pin in
required holes for proper vertical aiming;
Ensure truss hook is properly locked to flying bar;
Lift and position assembly, lock hook on truss suspension point and secure with hook
cable.
GEO S12 HARDWARE SETUP PROCEDURE Page 49/103
8.4.4 Single GEO S12 flown horizontally
Required items
1 x “U” Bracket for single horizontal GEO S12 (GPT-SSBRK)
1 x Lifting Ring (VNT-XHBRK)
Or 1 x Truss hook (VNT-TCBRK)
IMPORTANT
Ensure that suspension point is strong enough to hold GEO S12 weight.
Procedure
Slide GPT-SSBRK side plates into GEO S12 connecting plate oblong holes;
Lock safety pins into GEO S12 connecting plate;
IMPORTANT
Ensure that safety pins are properly locked into GEO S12 connecting panels.
Position “U” bracket over these side plates; align center holes;
Insert adjustment handles, adjust vertical angle and tight the handles to prevent GEO
S12 from rotating around “U” bracket;
Cable suspension:
Connect lifting ring VNT-XHBRK to “U” bracket by inserting 8x45 quick release pin
dedicated holes;
Ensure lifting ring is properly locked to “U” bracket;
Connect assembly to suspension point with sling and shackle (not provided).
Truss suspension
Connect truss hook VNT-TCBRK to “U” bracket by inserting 8x45 quick release pin in
dedicated holes;
Ensure truss hook is properly locked to “U” bracket;
Lift and position assembly, lock hook on truss suspension point and secure with hook
cable.
Page 50/103 GEO S12 HARDWARE SETUP PROCEDURE
8.4.5 Two GEO S12 on wind-up stand
Required items
1 x U” Bracket for two GEO S12 (GPT-PSBRK)
1 x Wind Up stand diameter 35mm (Eurotruss ES160 or equivalent);
IMPORTANT (WIND UP STAND)
- Wind Up stand must be rated for assembly weight (80kg rated load min);
- Wind Up stand must always be installed on a horizontal surface;
- Stand height and footprint must be defined to prevent assembly from collapsing;
- Ensure that public is not allowed within a safety area which radius is equal or higher
than assembly height.
Procedure
Set the 2 GEO S12 next to each other front grid to the floor
Slide GPT-PSBRK side plates into GEO S12s connecting plate oblong holes;
Lock safety pins into GEO S12s connecting plate;
IMPORTANT
Ensure that safety pins are properly locked into GEO S12s connecting panels.
Adjust inter-cabinet angle and lock to required angle value with 8x20quick release pins;
Position “U” bracket over these side plates; align centre holes;
Insert adjustment handles, adjust vertical angle and tight the handles to prevent GEO
S12s from rotating around “U” bracket;
Lift assembly on Wind Up stand
GEO S12 HARDWARE SETUP PROCEDURE Page 51/103
Page 52/103 GEO S12 HARDWARE SETUP PROCEDURE
Alternative Procedure (“Walder” procedure)
Below described procedure required 2 additional 8x20 quick release pins (BLGEOS)
Split the GPT-PSBRK side plates by removing screws and bolt;
Slide GPT-PSBRK lower half-plates into lower GEO S12 connecting plate oblong holes;
Lock safety pins into lower GEO S12 connecting plate;
Position “U” bracket over these lower half plates; align centre holes;
Insert adjustment handles, adjust vertical angle and tight the handles to prevent GEO
S12 from rotating around “U” bracket;
Lift assembly on Wind Up stand or on LS18 with PLSTD pole stand.
Slide GPT-PSBRK upper half-plates into upper GEO S12 connecting plate oblong
holes;
Lock safety pins into upper GEO S12 connecting plate;
Lift upper GEO S12 on top of lower one, and connect them together by inserting 8x20
quick release pins in articulation holes;
Adjust inter-cabinet angle and lock to required angle value with quick release pins.
IMPORTANT
Ensure that safety pins are properly locked into GEO S12 connecting panels.
GEO S12 HARDWARE SETUP PROCEDURE Page 53/103
Page 54/103 GEO S12 HARDWARE SETUP PROCEDURE
8.4.6 Two GEO S12 flown horizontally
Required items
1 x “U” Bracket for two GEO S12s (GPT-PSBRK)
1 x Lifting Ring (VNT-XHBRK)
Or 1 x Truss hook (VNT-TCBRK)
IMPORTANT
Ensure that suspension point is strong enough to hold two GEO S12s weight.
Procedure
Slide GPT-PSBRK side plates into GEO S12s connecting plate oblong holes;
Lock safety pins into GEO S12s connecting plate;
IMPORTANT
Ensure that safety pins are properly locked into GEO S12s connecting panels.
Adjust inter-cabinet angle and lock to required angle value with 8x20 quick release pins;
Position “U” bracket over these side plates; align centre holes;
Insert adjustment handles, adjust vertical angle and tight the handles to prevent GEO
S12s from rotating around “U” bracket;
Cable suspension:
Connect lifting ring VNT-XHBRK to “U” bracket by inserting 8x45 quick release pin
dedicated holes;
Ensure lifting ring is properly locked to “U” bracket;
Connect assembly to suspension point with sling and shackle (not provided).
Truss suspension
Connect truss hook VNT-TCBRK to “U” bracket by inserting 8x45 quick release pin in
dedicated holes;
Ensure truss hook is properly locked to “U” bracket;
Lift and position assembly, lock hook on truss suspension point and secure with hook
cable.
GEO S12 HARDWARE SETUP PROCEDURE Page 55/103
8.4.7 Two or more GEO S12 flown vertically
Required items
N Pair of Rigging Plates (GPT-XBOW) for N cabinets;
1 lifting ring (VNT-XHBRK) every two GEO S12;
4xN Quick release pins for N cabinets;
Properly rated slings, shackles, hoists… (not provided)
IMPORTANT
Lifting ring VNT-XHBRK and truss hook VNT-TCBRK are rated for a maximum of 2 GEO
S12s;
Ensure that suspension points are rated accordingly.
Procedure
Insert GPT-XBOW into connecting plates of both sides of the cabinet;
Lock safety pins into GEO S12s connecting plate;
IMPORTANT
Ensure that safety pins are properly locked into GEO S12s connecting panels.
Page 56/103 GEO S12 HARDWARE SETUP PROCEDURE
IMPORTANT
GEO S12 can be flown “Up” or “Down”:
- “Up” means Nexo logo on front grid is at the top;
- “Down” means Nexo logo on front grid is at the bottom.
GEO S12 can be connected “Up” or “Down” by simply flipping the cabinets.
Whenever possible, NEXO recommends symmetrical designs (ie Nexo logo in the same
position on Left and Right clusters for stereo designs)
Connect second Geo S12 with X-Bow front articulation holes and rear link bars and
ensure quick release pins are properly locked;
Repeat above steps for subsequent GEO S12’s;
IMPORTANT
Ensure angle settings are identical on upper and lower side of the cabinets
Ensure that safety pins are properly locked into GEO S12s connecting panels.
Ensure that all quick release pins are properly locked into their position.
Connect lifting rings to “U” bracket with 8x45 quick release pins supplied with VNT-
XHBRK; ensure quick release pin is properly locked;
GEO S12 HARDWARE SETUP PROCEDURE Page 57/103
Lift and position assembly, connect lifting rings to suspension points with sling and
shackle;
Secure assembly with secondary safety steel.
IMPORTANT
The requirements for secondary safety systems vary with territories. However, the
secondary safety steel MUST have a SWL equivalent or greater than that of the rigging
system.
Page 58/103 GEO S12 HARDWARE SETUP PROCEDURE
8.4.8 LS18 and three or more GEO S12 flown horizontally
Required items
1 x Bumper (GPT-BUMPER);
M pairs of LS rigging plates (LST-XBOW) for M x LS18 cabinets;
N Pair of Rigging Plates (GPT-XBOW) for Geo S12 cabinets;
4x(N+M) Quick release pins for (N+M) cabinets;
1 hoist (not provided).
IMPORTANT
Maximum GEO S12 quantity for flown vertical cluster is 12 (and eventually less).
Maximum LS18 quantity for flown vertical cluster is 6 (and eventually less)
Please check NS1 for mechanical Safety Working Load computations.
IMPORTANT
Motor hoist must be rated to support entire cluster weight. Please check configuration
in NS1 for proper motor hoist rating
GEO S12 XBOW ANGLE SETTINGS PLATE
LS18 XBOW ANGLE SETTINGS PLATE
GEO S12 HARDWARE SETUP PROCEDURE Page 59/103
Optional GPT-TLB link bar for GPT- XBOW
GPT-XBOWs are delivered with standard link bars which allow both stacked and flown setups.
However, these link bars require perfect alignment of angle setting holes when adding cabinets.
GPT-XBOW STANDARD LINK BAR
To facilitate flying operation, an optional link bar with oblong holes (GPT-TLB, pair of link bars provided
with two 8x20 quick release pin) is available in the GEO S12 accessory range.
GPT- XBOW OPTIONAL GPT-TLB LINK BAR
To install GPT-TLB, remove the standard link as well as nut, screw and washers.
When using GPT-XBOW for flown setups, insert pins in the oblong hole and opposite circular hole.
REMOVING STANDARD LINK BAR INSERTING PIN - FLOWN SETUPS
Page 60/103 GEO S12 HARDWARE SETUP PROCEDURE
Procedure
Insert LST-XBOW into connecting plates of both sides of LS18s;
Insert GPT-XBOW into connecting plates of both sides of GEO S12s;
Lock safety pins into LS18 and GEO S12s connecting plate
IMPORTANT
Ensure that safety pins are properly locked into LS18s and GEO S12s connecting
panels.
GEO S12 HARDWARE SETUP PROCEDURE Page 61/103
IMPORTANT
GEO S12 can be flown “Left” or “Right” :
- “Left” means Nexo logo on front grid is left as seen from front;
- “Right” means Nexo logo on front grid is right as seen from front.
GEO S12 can be connected to bumper “Left” or “Right” by simply flipping the cabinets.
Whenever possible, NEXO recommends symmetrical designs (preferably NEXO logo
outwards in stereo configurations)
LS18s are always flown upwards (ie with NEXO logo properly oriented and pole stand
hole up)
Connect bumper to first LS18 or GEO S12 using “lift” points of XBOWs; ensure quick
release pins are properly locked;
Insert axis in bumper NS-1 predefined hole and secure it with provided “R” clip;
NB: Bumper holes are numbered #-17 to #17, please refer to NS-1 to determine axis position in
relation to bumper angle requirements.
If bumper is flown with 2 hoists, then they should be connected to holes #-17 and #17.
Connect hoist hook to bumper axis and lift assembly to sufficient height in order to
connect a second LS18 or GEO S12;
Connect second LS18 or Geo S12 with X-Bow front articulation holes and rear link bars
and ensure quick release pins are properly locked;
Repeat above steps for subsequent cabinets.
Page 62/103 GEO S12 HARDWARE SETUP PROCEDURE
IMPORTANT
Ensure angle settings are identical on both sides of the cabinets.
Ensure that safety pins are properly locked into LS18s and GEO S12s connecting
panels.
Ensure that all quick release pins are properly locked into their position.
Lift cluster to NS-1 defined rigging height, secure cluster horizontally to prevent it from
rotating;
Secure bumper with secondary safety steel.
IMPORTANT
The requirements for secondary safety systems vary with territories. However, the
secondary safety steel MUST have a SWL equivalent or greater than that of the rigging
system.
GEO S12 HARDWARE SETUP PROCEDURE Page 63/103
8.4.9 Ground stacked LS18 and GEO S1210
Required items
M pairs of rigging plates (LST-XBOW) for M x LS18
N Pairs of Rigging Plates (GPT-XBOW) for N x GEO S12;
1 ground stack device (GPT-GSTK);
4xN Quick release pins for N cabinets;
IMPORTANT
- Ground stack device GPT-GSTK is rated for a maximum of:
6xGEO S1210s or 2xLS18s + 4xGEO S1210s or 4xLS18s
in any inter cabinet angle configuration, provided this device is assembled according to
below rules.
- Ground stack device GPT-GSTK must always be installed on a horizontal surface;
- Bottom GEO S12 tilt angle must be limited to +/-10°
- Ensure that public is not allowed within a safety area which radius is equal or higher
than assembly height.
- It is highly recommended to secure the system to a fix point located at the back of the
stack.
Optional GPT-TLB link bar for GPT-XBOW
GPT-XBOWs are delivered with standard link bars which allow both stacked and flown setups.
However, these link bars require perfect alignment of angle setting holes when adding cabinets.
GPT- XBOW STANDARD LINK BAR
To facilitate flying and stacked operation, an optional link bar with oblong holes (GEOS12-TLB, pair of
link bars provided with two 8x20 quick release pin) is available in the GEO S12 accessory range.
GPT-XBOW OPTIONAL GPT-TLB LINK BAR
To install GPT-TLB, remove the standard link as well as nut, screw and washers.
When using GPT-XBOW for stacked setups, insert pins in the two circular holes.
REMOVING STANDARD LINK BAR INSERTING PINS - STACKED SETUPS
Page 64/103 GEO S12 HARDWARE SETUP PROCEDURE
LS18 and GEO S12 ground stack device description
GPT-GSTK ground stack device includes:
two supporting beams, which support assembly weight;
two connecting beam, which allow connection of the beams to the first cabinet;
one reinforcement beam, to rigidify ground stack device sideways;
Axis, “R” clips and handles to assemble the ground stack device
Procedure
Assemble the two connecting beam and the reinforcement beam with the handles;
Depending on tilt angle – negative, null or positive - to be achieved, there are three
positions to connect above assembly to the supporting beams; below drawings detail
these configurations:
Connect the reinforcement bar to the supporting beams according to required tilt angle
configuration using 2 axis per side; secure the axis with provided “R” clips;
GEO S12 HARDWARE SETUP PROCEDURE Page 65/103
Insert GPT-XBOW into connecting plates of both sides GEO S12s;
Insert LST-XBOW into connecting plates of LS18s
Lock safety pins into LS18s and GEO S12s connecting plate;
IMPORTANT
Ensure that safety pins are properly locked into LS18s and GEO S12s connecting
panels.
Page 66/103 GEO S12 HARDWARE SETUP PROCEDURE
Connect bottom LS18 or GEO S12 to GPT-GSTK Ground stacking device with 4 8x20
quick release pins;
Connect second LS18 or Geo S12 with X-Bow front articulation holes and rear link bars
and ensure quick release pins are properly locked;
Repeat above steps for subsequent cabinets
GEO S12 HARDWARE SETUP PROCEDURE Page 67/103
Once the assembly is completed, rotate rear or front GEO S12 ground stack device
adjustable legs to definitive tilt angle, ensuring that +/-10° is never exceeded on bottom
GEO S12.
Page 68/103 GEO S12 HARDWARE SETUP PROCEDURE
8.5 Testing and Maintenance of the system
General: Geo is a precision piece of equipment and requires regular attention to
maintenance in order to give long and reliable service. NEXO recommends regular
testing of loudspeaker rigging components, preferably using a suitable test rig coupled
with a visual inspection.
Fasteners: there are several critical points in the LS18GEO S12 cabinets.
Of primary concern are:
a) The grid screws attaching the grid to the cabinet
b) The machine screws attaching the connecting plates to the cabinet.
c) The screws attaching the directivity flanges to the front of the cabinet.
These fasteners should be regularly checked and tightened as necessary.
Cleaning: The exterior of the cabinet and the rigging system can be cleaned with a
damp cloth soaked in mild soapy water. On no account use solvent based cleaners ,
which may damage the finish of the cabinet
After cleaning, the rigging system must be treated with a suitable lubricant to prevent
rusting. NEXO recommends the use of Scottoil FS365 which is a water-based lubricant
with a mixture of machine oil, surfactant and anti-rust treatment.
SYSTEM ALIGNMENT GUIDELINES Page 69/103
9 SYSTEM ALIGNMENT GUIDELINES
The NX242’s factory delay presets are optimised to provide the best possible crossover between the
GEO S12 and CD18 / S2 / GEO SUB systems. The reference point for this adjustment is the front of
each cabinet. (This means that the internal delays needed to achieve a correct time alignment are set
for cabinets standing next to each other with both fronts aligned). We recommend that the system is
adjusted so that arrivals from GEO S12 and CD18 / S2 / GEO SUB are coincident at a fairly distant
listening position.
9.1 GEO S12 Vertical Cluster design
Cluster design must be done with NS-1 (previously Geosoft2), which provides very intuitive and fast
method to determine all cluster geometry parameters in relation to venue where cluster is implemented.
NS-1 is a freeware available for all Nexo users. Please contact your local distributor for
licensing procedure.
IMPORTANT
Never install a GEO S12 cluster without checking its acoustical performances and
mechanical safety in NS-1 prior to installation.
Please contact your local distributor for assistance and/or training NS-1
9.2 Stacked LS18s and Flown GEO S12
Recommended NX242 GEOS12 setup family: X-OVER
In the example below, r1 being the distance from GEO S12 array to listener position, and r2 being the
distance from GEO SUB to listener position, the distance difference is then r1–r2 (specified meters or
feet).
r1 > r2, the delay should be set on the LS18 NXAMP TDcontroller channel.
r1 < r2, the delay should be set on the GEO S12 NXAMP TDcontroller channel
To convert the result in time delay (specified in seconds), apply:
t = (r1-r2)/C r1 and r2 in meters, C (sound speed) 343 m/S.
Set the units to meters, feet or seconds according to your preference). Delay will have to be adjusted
according to the distance difference r1–r2 (see figure below).
r2
r1
Page 70/103 SYSTEM ALIGNMENT GUIDELINES
9.3 Driving the LS18s from the AUX send
It is quite common to use the AUX send of a mixing desk to drive the Sub section of a PA system. This
gives the mixing engineer more flexibility to set the level of the subbass relative to the main PA, apply
special effects, or to use a different EQ on the Sub. However, it also raises some serious issues for the
performance & safety of the system (mostly time alignment).
At NEXO, great care is taken to design optimum phase alignment from one octave above to one octave
below the crossover frequency point. By doing so, drivers are working perfectly together and providing
the best efficiency possible. It is then up to the user to adjust the delay on the NX242 to match the
physical path difference of the different systems. It is thus possible to get a well adjusted system, even
without measuring instruments.
If LS18s are driven form an AUX output, NXAMPs are fed with two signals coming from different
sources. If those two sources (MAIN output & AUX send) are not exactly in phase, delay is introduced
into the crossover between the GEO S12 array and the LS18s. It is then mandatory to use proper
measurement tool to optimize phase response.
Why is it unlikely that AUX and MAIN outputs have the same phase?
Signal paths are likely to be different; any filter modifying the bandwidth and EQ of the
signal is also affecting the phase.
Example: a 24dB/oct high pass filter set at 15Hz is affecting amplitude of the signal by only
0.6dB at 30Hz, but the phase shift is 90°!! At 100Hz we can still measure 25° of phase shift.
Limiting bandwidth with a low pass filter can introduce a phase difference of up to 180°
(completely out of phase) at the cross over point.
If the signal is passing though any digital equipment, between 1.4ms and 2.2ms is being
added (around 70° phase shift at 100Hz) due solely to the converter delay! The additional
delay due to the processing itself (look ahead compressor, delay…) can be quite important
as well.
If both outputs are not measured in the actual configuration, it is very likely that phase alignment will not
be correct.
Consequences of badly aligned systems
Mis-aligned systems have lower efficiency: i. e. for the same SPL the system will have to be driven
harder, activating the displacement & temperature protection at lower output levels. Both sound quality
and reliability will decrease as the system is stressed.
Precautions & Checks
Before using the AUX of a mixing desk, ensure that MAIN and AUX outputs are in phase;
Always apply identical EQ or processing on both channels, so that the phase relationship will not be
altered;
Never add additional low pass filtering on the SUB or high pass filtering on the main system;
Inverting polarity on one channel should always result in a massive difference near the crossover point.
If that is not the case, the system is no longer aligned.
SYSTEM ALIGNMENT GUIDELINES Page 71/103
9.4 Recommended installation tools and equipment
Tape measure – should be 30m/100ft in length and be of durable fibre material. Have
one per array available to speed up the installation process.
Laser Inclinometer – For measuring vertical and horizontal angles in the venue. An ideal
product is the Calpac ‘Laser projecting a dot’ version which costs approximately 60 €.
Spirit level – used to ascertain the trueness of the surface from which the angle
measurements originate.
Rangefinder measuring device – either a Disto type laser measure or an optical laser
rangefinder can be used. Devices such as the Bushnell ‘Yardage Pro’ sports
rangefinders provide sufficiently accuracy and are easy to use. They have the additional
advantage of working very well in bright sunlight.
Electronic calculator with trigonometric functions to calculate the height from ground
level to points in the room. The formula to calculate height of a point from measured
angle and distance is:
Height of point = Sin(vertical angle in degrees) x distance to point
NB: Take care when using spreadsheets as they calculate using radians by default. To
convert degrees to radians use the formula:
Angle (in radians)=3.142 x Angle (in degrees)/180
Computer – Laptop or Desktop PC running Windows XP with the current version of
NEXO NS-1 installed. It is not possible to configure a Geo tangent array properly without
using NS-1. Note that, when NS-1 designs are prepared prior to arrival at the venue, it is
often necessary to modify or update the design to accommodate special circumstances.
A PC is absolutely essential to make such changes.
Audio Analysis Software – recommended but not absolutely essential, programs such as
Easera Systune, Smaart, WinMLS enable rapid and detailed analysis of the installation.
Consider taking a training course in using one of these tools if you are not already
competent with them – it will pay dividends in increased performance of the system.
Page 72/103 GEO S12 – LS18S SYSTEM CHECK LIST
10 GEO S12 – LS18S SYSTEM CHECK LIST
It is essential to execute all these check steps prior to perform a sound check on the “front end” to the
system. Following this checklist step by step will prevent many troubles and will save time in the end.
10.1 Are the speakers properly connected and angled ?
Attach the first series of modules to the bumper.
Before flying, verify that all channels of all modules are functioning properly.
To check that all elements have the proper amplitude and phase, you should listen to the
upper boxes at a close distance (<1 meter). You should be able to move from the top to
the bottom of the cluster without hearing any change in the tonal balance.
Verify that the angle settings are the same on both sides of each module.
Raise the bumper, attach the next series of modules and repeat the above checks.
Make sure that these series of modules sum properly with the modules above them.
When all the modules are flown, check that the aiming angles are the same left and
right.
Make sure that multiple GEO S12 and LS18 are summing properly: 6 dB gain per
doubling of quantity.
10.2 Final Pre-Sound Check Check
Play a CD track mono left, and then right: both sides must sound strictly identical. When listening in the
centre between Left and Right GEO S12’s, everything from LF to HF should be located to the “phantom
centre” position. If not, repeat the above check sequence to identify the source of the problem.
TECHNICAL SPECIFICATIONS Page 73/103
11 TECHNICAL SPECIFICATIONS
11.1 LS18 Subwoofer
11.1.1 System specifications
SYSTEM SPECIFICATIONS
LS18 with NXAMP TD Controller
Frequency Response [a]
35 Hz - 120 Hz ±3dB
Usable Range @-6dB [a]
32Hz - 130 Hz
Sensitivity 1W @ 1m [b]
107 dB SPL Nominal
Nominal Peak SPL @ 1m [b]
137 to 140 dB Peak
Nominal Impedance
8
Crossover Frequencies
60 Hz – 85 Hz - 120 Hz Active
Amplified Controller
NXAMP4x1: 2 x LS18 in parallel on 2 bridged channels
NXAMP4x4: 2 x LS18 on 1 channel
SYSTEM OPERATION
Electronic Controller
The NEXO NXAMP presets are precisely matched to the LS series cabinets and include sophisticated
protection algorithms. Using LS Series cabinets without a properly connected NXAMP will result in poor
quality and can damage components
Speaker Cables
LS18 is wired 1- & 1+ on 2 In/Out Speakon connectors
Single cables can thus be used to loop through to PS15-R2 or to Geo S12.
PRODUCT FEATURES
LS18 (LS18e)
Components:
1 x 18’’ (46cm) 4’’ voice coil long excursion 8 driver
Height x Width x Depth
510 x 675 x 775 mm (20.1” x 26.1” x 30.5”)
Weight : Net
55.5 kg excluding accessories (122.3 lb)
Connectors
2 x NL4MP Speakon 4 pole
Construction
Baltic Birch Ply & structured black coating
Fittings: Handles
4 metal recessed pockets (None)
Front finish
Molded Dark Grey Metal Grill
Flying Points
Two side plates connecting with external accessories (None)
Stand fittings
Internal Steel Stand Fitting on Top (35mm, 1"3/8) allows pole mounting for PS15 or Geo S12 (None)
As part of a policy of continual improvement, NEXO reserves the right to change specifications without notice.
[a] Response curves & data : Half-Space Anechoïc radiation for the LS18 + NXAMP.
[b] Sensitivity & Peak SPL data : these will depend on spectral distribution and crest factor of program material. Measured with band limited Pink Noise., Wideband to the
specified ±3dB range. Data are for speaker + processor + recommended amplifier combinations. Peak SPL is at clipping of recommended amplifier.
[c] Directivity curves & data : obtained by computer treatment on off axis response curves.
Page 74/103 TECHNICAL SPECIFICATIONS
11.1.2 Dimensions
TECHNICAL SPECIFICATIONS Page 75/103
11.2 GEO S1230 Module
11.2.1 System specifications
PRODUCT FEATURES
GEO S1230
Components
HF: 1 x 3” voice coil, 1.4” throat 16 Ohms driver on a 5° hyperboloid reflective wavesource.
LF: 1 x 12” (30cm) high excursion neodymium 16 Ohm driver.
Height x Width x Depth
344 x 675 x 400 mm (13 1/2” x 26 1/2” x 15 1/2”) excluding accessories
Rigging axis to axis height: 345mm (131/2”)
Shape
30° Trapezoid.
Weight: net
26.8 kg (59.1 lbs) excluding accessories.
Connectors
2 x NL4MP SPEAKON 4 pole (In & Through)
Construction
Baltic birch ply with structured black coating.
Front finish
Molded Dark Grey Metal Grill.
Flying points
Two plates connecting with external accessories.
Intercabinet angle adjustments = (16°) - 22.5° - 30°
SYSTEM SPECIFICATIONS
GEO S1230 with NX242 TDcontroller & NX-tension Card
Frequency response [a]
53 Hz – 19 kHz ± 3 dB
Usable range @-6dB [a]
50 Hz – 20 kHz
Sensitivity 1W @ 1m [b]
103 dB SPL nominal
Peak SPL @ 1m [b]
131 to 133dB Peak (for 500 to 900 W RMS Amplifier)
Dispersion [c]
Coupling Plane: 28.5°.
Non-Coupling Plane: Configurable 80° / 120°.
Crossover frequencies
LF-HF: 1.1 kHz Passive or Active (internally configurable)
Nominal impedance
HF: 16 Ohms; LF : 16 Ohms;
Recommended amplifiers
3 GEO S1230 in Parallel
HF: 875 to 1550 Watts into 4 Ohms
LF: 1750 to 3100 Watts into 4 Ohms
4 GEO S1230 in parallel
HF: 1000 to 1800 Watts into 4 Ohms
LF: 2000 to 3600 Watts into 4 Ohms
6 GEO S1230 in parallel
HF: 1650 to 3000 Watts into 2 Ohms
LF: 3300 to 6000 Watts into 2 Ohms
SYSTEM OPERATION
Electronic controller
The NEXO TDcontrollers presets are precisely matched to the GEO S12 Series cabinets and include sophisticated
protection. Using GEO S12 Series cabinets without a properly connected NEXO TDcontrollers will result in poor sound
quality and can damage components.
Sub-bass
CD18 / GEO SUB / S2 extend system low frequency response down to 32 Hz / 38 Hz / 32 Hz
Speaker cables
Active:; 1-/1+:LF; 2-/2+: HF
Passive: 1-/1+: Not Connected; 2-/2+:LF + HF.
Accessories
Please refer to the GEO S12 user manual before any operation.
As part of a policy of continual improvement, NEXO reserves the right to change specifications without notice.
[a] Response curves and data: anechoic far field above 200 Hz, half-space anechoic below 200 Hz.
[b] Sensitivity & peak SPL: will depend on spectral distribution. Measured with band limited pink noise.
Refers to the specified +/- 3 dB range. Data are for speaker + processor + recommended amplifier combinations.
[c] Directivity curves and data: 1/3 octave smoothed frequency response, normalized to on-axis response. Data obtained by computer processing of off-axis
response curves.
[d] Please refer to the GEO S12 user Manual.
Usable range data: frequency response capability with TD crossover slopes removed.
Page 76/103 TECHNICAL SPECIFICATIONS
11.2.2 Dimensions
11.2.3 Diagrams
TECHNICAL SPECIFICATIONS Page 77/103
11.3 GEO S1210 Module
11.3.1 System specifications
PRODUCT FEATURES
GEO S1210
Components
HF: 1 x 3” voice coil, 1.4” throat 16 Ohms driver on a 5° hyperboloid reflective wavesource.
LF: 1 x 12” (30cm) high excursion neodymium 16 Ohm driver.
Height x Width x Depth
344 x 675 x 378 mm (13 1/2” x 26 1/2” x 14 7/8”) excluding accessories
Rigging axis to axis height: 345mm (131/2”)
Shape
10° Trapezoid.
Weight: net
28.05 kg (61.8 lbs) including array assembly system.
Connectors
2 x NL4MP SPEAKON 4 pole (In & Through)
Construction
Baltic birch ply with structured black coating.
Front finish
Molded Dark Grey Metal Grill.
Flying points
Two plates connecting with external accessories.
Intercabinet angle adjustments = 0.2°, 0.315°, 0.5°, 0.8°; 1.25°, 2.0°, 3.15°, 5°, 6.3°, 8.0°, 10.0° (logarithmic steps)
SYSTEM SPECIFICATIONS
GEO S1210 with NX242 TDcontroller & NX-tension Card
Frequency response [a]
53 Hz – 19 kHz ± 3 dB
Usable range @-6dB [a]
50 Hz – 20 kHz
Sensitivity 1W @ 1m [b]
103 dB SPL nominal
Peak SPL @ 1m [b]
Configuration Dependent [d]
Dispersion [c]
Coupling Plane: Configuration dependent [d]
Non-Coupling Plane: Configurable 80° / 120°.
Crossover frequencies
LF-HF: 1.1 kHz Passive or Active (internally configurable)
Nominal impedance
HF: 16 Ohms; LF : 16 Ohms;
Recommended amplifiers
3 GEO S1210 in Parallel
HF: 875 to 1550 Watts into 4 Ohms
LF: 1750 to 3100 Watts into 4 Ohms
4 GEO S1210 in parallel
HF: 1000 to 1800 Watts into 4 Ohms
LF: 2000 to 3600 Watts into 4 Ohms
6 GEO S1210 in parallel
HF: 1650 to 3000 Watts into 2 Ohms
LF: 3300 to 6000 Watts into 2 Ohms
SYSTEM OPERATION
Electronic controller
The NEXO TDcontrollers presets are precisely matched to the GEO S12 Series cabinets and include sophisticated
protection. Using GEO S12 Series cabinets without a properly connected NEXO TDcontrollers will result in poor sound
quality and can damage components.
Array design
Arrays of less than 4 x GEO S1210 will provide poor dispersion control and are neither recommended nor supported.
Sub-bass
CD18 / GEO SUB / S2 extend system low frequency response down to 32 Hz / 38 Hz / 32 Hz
Speaker cables
Active:; 1-/1+:LF; 2-/2+: HF
Passive: 1-/1+: Not Connected; 2-/2+:LF + HF.
Accessories
Please refer to the GEO S12 user manual before any operation.
As part of a policy of continual improvement, NEXO reserves the right to change specifications without notice.
[a] Response curves and data: anechoic far field above 200 Hz, half-space anechoic below 200 Hz.
[b] Sensitivity & peak SPL: will depend on spectral distribution. Measured with band limited pink noise.
Refers to the specified +/- 3 dB range. Data are for speaker + processor + recommended amplifier combinations.
[c] Directivity curves and data: 1/3 octave smoothed frequency response, normalized to on-axis response. Data obtained by computer processing of off-axis
response curves.
[d] Please refer to the GEO S12 user Manual.
Usable range data: frequency response capability with TD crossover slopes removed.
Page 78/103 TECHNICAL SPECIFICATIONS
11.3.2 Dimensions
11.3.3 Diagrams
TECHNICAL SPECIFICATIONS Page 79/103
11.4 GEO S12 Touring Applications Accessories
11.4.1 GPT- BUMPER
Parts
Dimensions
Weight
20 kg / 44.1 Lbs
Page 80/103 TECHNICAL SPECIFICATIONS
11.4.2 LS18 Rigging Plates
Parts
Dimensions
TECHNICAL SPECIFICATIONS Page 81/103
11.4.3 GEO S12 Rigging Plates
Parts
Dimensions
Weight (pair)
10.7 kg / 23.6 Lbs
Page 82/103 TECHNICAL SPECIFICATIONS
11.4.4 Tension Mode Link Bars for GPT-XBOW
Parts
Dimensions
Weight (pair)
0.6 kg / 1.3 Lbs
TECHNICAL SPECIFICATIONS Page 83/103
11.4.5 Lifting Ring
Parts
Dimensions
Weight (kit)
0.3 kg / 0.661 Lbs
Page 84/103 TECHNICAL SPECIFICATIONS
11.4.6 Truss hook for GPT-PSBRK or GPT-SSBRK
Parts
Dimensions
Weight (kit)
0.620 kg / 1.37 Lbs
TECHNICAL SPECIFICATIONS Page 85/103
11.4.7 Truss hook for single vertical GEO S12
Parts
Dimensions
Weight (kit)
0.7 kg / 1.54 Lbs
Page 86/103 TECHNICAL SPECIFICATIONS
11.4.8 “U” Bracket for single vertical GEO S12
Parts
Dimensions
Weight (kit)
7 kg / 15.4 Lbs
TECHNICAL SPECIFICATIONS Page 87/103
11.4.9 U” Bracket for two vertical GEO S12
Parts
Dimensions
Weight (kit)
10.4 kg / 22.9 Lbs
Page 88/103 TECHNICAL SPECIFICATIONS
11.4.10 Ground Stacking Device for up to 6 GEO S1210
Parts
04GPT-GSTK
Dimensions
Weight (kit)
26.5 kg / 58.4 Lbs
TECHNICAL SPECIFICATIONS Page 89/103
11.5 GEO S12 Fixed Installations Accessories
11.5.1 LS18 & GEO S12 Bumper (VNI-BUMPER)
Parts
Dimensions
Weight (kit)
14.5 kg / 32 Lbs
Page 90/103 TECHNICAL SPECIFICATIONS
11.5.2 LS18 Counter Plate (LSI-CPLA)
Parts
Dimensions
TECHNICAL SPECIFICATIONS Page 91/103
11.5.3 GEO S12 Counter Plate (VNI-CPLA)
Parts
Page 92/103 TECHNICAL SPECIFICATIONS
11.5.4 LS18 & GEO S12 Connecting Plate 1 (VNI-ANPL1)
Parts
Dimensions
Weight (kit)
7.5 kg / 16.5 Lbs
TECHNICAL SPECIFICATIONS Page 93/103
11.5.5 GEO S12 Connecting Plate 2 (VNI-ANPL2)
Parts
Dimensions
Weight (kit)
6.2 kg / 13.7 Lbs
Page 94/103 TECHNICAL SPECIFICATIONS
11.5.6 GEO S12 Connecting Plate 3 (VNI-ANPL3)
Parts
Dimensions
Weight (kit)
5.5 kg / 12.1 Lbs
TECHNICAL SPECIFICATIONS Page 95/103
11.5.7 Single GEO S12 “U” Bracket
Parts
Dimensions
Weight
2.9 kg / 6.4 Lbs
Page 96/103 TECHNICAL SPECIFICATIONS
11.5.8 “L” Bracket for cable suspension
Parts
Dimensions
Weight (kit)
1.75 kg / 3.86 Lbs
TECHNICAL SPECIFICATIONS Page 97/103
11.5.9 “U” Bracket for rigid suspension
Parts
Dimensions
Weight (kit)
1.75 kg / 3.86 Lbs
Page 98/103 TECHNICAL SPECIFICATIONS
11.5.10 GEO S12 Push-Pins (04VXT-BL820)
04VXT-BL820
WEIGHT: 0.032 KG / 0.07 LBS
GEO S12 SERIES PARTS & ACCESSORIES LIST Page 99/103
12 GEO S12 SERIES PARTS & ACCESSORIES LIST
12.1 Modules & Control Electronics List
MODEL
DRAWING
DESCRIPTION
LS18
Subwoofer Module
GEO S1230
GEO S1230 Module
GEO S1210
GEO S1210 Module
NXAMP4x1
Digital Powered Controller 4x1300W
NXAMP4x4
Digital Powered Controller 4x4000W
12.2 Accessories List
MODEL
DRAWING
DESCRIPTION
GPT-BUMPER
Main GEOS12 Bumper for touring application.
LST-XBOW
Rigging plates for LS18 touring applications (pair).
GPT-XBOW
Rigging plates for GEO S12 touring applications (pair).
GPT-TLB
Link Legs for GPT-XBOW with Oblong Holes (pair,
includes 2 8x20 Quick Release Pins)
BL820
8x20 Quick Release Pin for Geo S8 / GeoS12 / RS15
Page 100/103 GEO S12 SERIES PARTS & ACCESSORIES LIST
MODEL
DRAWING
DESCRIPTION
VNT-XHBRK
Lifting Ring for GPT-SSBRK or GPT-PSBRK or GPT-
XBOW (includes 8x45 Quick Release Pin).
VNT-TCBRK
Truss hook for GPT-SSBRK or GPT-PSBRK or GPT-
XBOW (includes 8x45 Quick Release Pin)
VNT-TTC
Truss hook for single vertical GEO S12
GPT-SSBRK
“U” Bracket for single horizontal GEO S12 on tripod or
on truss hook or lifting ring
GPT-PSBRK
U” Bracket for two GEO S12 on subwoofer pole stand
or on truss hook or on lifting ring
GPT-GSTK
Ground Stack Device for up to 6 Geo S1210
VNI-BUMPER
Main LS18 & GEOS12 Bumper for fixed installation.
LSI-CPLA
LS18 Counter-Plates for fixed installation
VNI-CPLA
GEO S12 Counter-Plates for fixed installation
VNI-ANPL1
Geo S12 and LS18 Connecting Plates / range: 0.20° -
3.15° for fixed installation.
VNI - ANPL2
Geo S12 Connecting Plates / range: 5.00° - 10.00° for
fixed installation.
VNI - ANPL3
Geo S12 Connecting Plates / range: 16.00° - 30.00°
for fixed installation.
VNI-UBRK12
“U” Bracket for fixed installation.
GEO S12 SERIES PARTS & ACCESSORIES LIST Page 101/103
MODEL
DRAWING
DESCRIPTION
VNI- LBRK
“L” Bracket for cable suspension (for fixed installation).
VNI- ABRK
“U” Bracket for rigid suspension (for fixed installation).
GPT-2CASE
Flight Case for 2 GEO S12 with accessory tray
GPT-3CASE
Flight Case for 3 GEOS12 equipped with XBOWS
GPT-BCASE
Flight Case for 2 GEO S12 bumpers and accessories
Page 102/103 USER NOTES
13 USER NOTES
USER NOTES Page 103/103
France
Nexo S.A.
Parc d’activité de la dame jeanne
F-60128 PLAILLY
Tel: +33 3 44 99 00 70
Fax: +33 3 44 99 00 30
E-mail: info@nexo.fr
www.nexo-sa.com

Navigation menu