Yamaha YHT 23 Quick Connect Connection Diagram YHT23QC
User Manual: Yamaha YHT-23 Connection Diagram
Open the PDF directly: View PDF .
Page Count: 16
Download | |
Open PDF In Browser | View PDF |
YHT-23 QUICK-CONNECT GUIDE YHT-23 Q U I C K -C O N N E CT G U I D E I NTRODUCTION Yamaha developed the YHT-23 A/V Home Theater package to turn your home into a theater. In addition to enhancing the sound of a video source, like your TV, DVD player, or VCR, the YHT-23 also superbly reproduces audio sources, such as a CD player or a cassette deck. For the video portion, you will need a DVD (or LD) player or a hi-fi stereo VCR and a television or monitor. Refer to the Yamaha HTR-5240 Owner’s Manual, as well as the owner’s manuals that came with your other components, for complete instructions and cautions. Be sure to turn off all power while making connections. This Quick-Connect Guide will help you get started. Study the speaker system plan (below), and then use the interconnect diagrams (on the following pages) to connect the receiver and speakers to your system. Please keep this guide handy for future reference. NOTE: Label the end of each speaker wire (i.e., left rear, right front, etc.) before connecting them to the A/V receiver. For wire runs over 30 feet, use larger 18- or 16-gauge speaker wire. T OOLS A ND P ARTS The YHT-23 Home Theater package consists of (1) HTR-5240 A/V receiver with a universal remote control, (1) NS-AP327 package containing (4) 2-way NS-A327 front/rear channel speakers, (1) NS-AC327 2-way center-channel speaker, 100' of speaker wire, (1) YST-SW45 Powered Subwoofer, and related owner’s manuals. You will also need: • Toggle bolts, molly anchor screws, sheet metal screws, and/or speaker brackets (for securing the NS-A327 speakers to walls) NOTE: If you are unsure of how to securely and safely fasten speakers to a wall, please contact a reliable source about the best type of hardware for your particular wall's construction. Secure installation is the purchaser's responsibility. • Wire strippers (optional) S PEAKER S YSTEM P LAN YST-SW45 Subwoofer (on floor) C NS-A327 NS-A327 Sub (left side, same height as TV) L NS-AC327 (right side, same height as TV) R (on top or below TV) 6'~ 8' apart L = Left Channel R = Right Channel C = Center Channel S = Surround Channel Couch Listening Area S S NS-A327 (on stand or wall, at least ear level or preferably higher) 8'~10' apart NS-A327 (on stand or wall, at least ear level or preferably higher) 1 YHT-23 Q U I C K -C O N N E CT G U I D E C ONNECTING A UDIO C OMPONENTS Yamaha HTR-5240 Receiver (Rear Panel) NOTE: For your convenience, the Yamaha HTR-5240 receiver is equipped with two switched ac outlets (100 W max.). If desired, use them to power on connected components (e.g., CD player or turntable) each time the receiver is turned on. However, do not use them for components equipped with clocks (e.g.,VCR). Cassette Deck * Use Playback Or Line Out ** Use Line In Ground L Out* R Out* L In** R In** Turntable L Out R Out L L R R CD Player (Changer) L Out R Out RCA Cable Color Codes Yellow = Video White = Left Audio Red = Right Audio 2 Use RCA Audio Cables For Audio Interconnections YHT-23 Q U I C K -C O N N E CT G U I D E C ONNECTING T HE YHT-23 S PEAKERS (B ASIC H OOK -U P ) NS-A327 (Front Right) Clear/ Stripe Wire Clear/ Stripe Wire NS-A327 (Front Left) NS-AC327 (Center Channel) Clear Wire Clear Wire Clear/ Stripe Wire To Speakers Clear Wire YST-SW45 (Subwoofer) From Amplifier Initial Settings (on Front Panel) STANDBY/ON HIGH CUT 50 Hz 150 Hz VOLUME 0 10 + R −− + L Main Spkrs. Yamaha HTR-5240 A/V Receiver (Rear Panel Speaker Terminals) Surround Cntr R L + − + − Set IMPEDANCE Selector to left position Clear/ Stripe Wire Clear Wire ❸ ❷ Speaker Wiring ❶ RED = positive (+) use clear wire Clear/ Stripe Wire Clear Wire BLK = negative (–) use clear with white stripe wire ❶ Strip 1 ⁄4 " off ends of speaker wires. NS-A327 (Surround Right) ❷ Loosen terminals. ❸ Insert speaker wires; tighten terminals. NS-A327 (Surround Left) 3 YHT-23 Q U I C K -C O N N E CT G U I D E C ONNECTING T HE YHT-23 S PEAKERS (A DVANCED S PEAKER C ONNECTIONS ) NS-A327 (Front Right) Clear/ Stripe Wire Clear/ Stripe Wire NS-A327 (Front Left) NS-AC327 (Center Channel) Clear Wire Clear Wire Clear/ Stripe Wire Clear Wire YST-SW45 STANDBY/ON HIGH CUT (Subwoofer Rear) VOLUME INPUT2 50 Hz 150 Hz 0 AUTO STANDBY 10 LOW Initial Settings (on Front Panel) HIGH OFF + R −− + L Main Spkrs. Yamaha HTR-5240 A/V Receiver (Rear Panel Speaker Terminals) Surround Cntr RCA Audio Cable (not included) R + − L + − Set IMPEDANCE Selector to left position Clear/ Stripe Wire Clear Wire ❸ ❷ Speaker Wiring ❶ RED = positive (+) use clear wire Clear/ Stripe Wire Clear Wire BLK = negative (–) use clear with white stripe wire ❶ Strip 1 ⁄4 " off ends of speaker wires. NS-A327 (Surround Right) 4 ❷ Loosen terminals. ❸ Insert speaker wires; tighten terminals. NS-A327 (Surround Left) YHT-23 Q U I C K -C O N N E CT G U I D E C ONNECTING V IDEO C ABLES F OR V IDEO C OMPONENTS Yamaha HTR-5240 Receiver (Rear Panel) NOTE: When using a hi-fi stereo VCR, set the Tuner/Line switch (on the VCR) to Line position to record from another source connected to the Yamaha HTR-5240 receiver. Monitor/TV DVD or LD Player (or Video Game) VIDEO SIGNAL VIDEO DVD/LD SAT/D-TV IN OUT VCR Video Out Optional 75-ohm Coaxial Cable ANT In MONITOR OUT Video In Satellite Receiver Video Out Hi-Fi Stereo VCR Video In Video Out ANT Out (RF Out) Use RCA Video Cables And Jacks For Video Interconnections RCA Cable Color Codes Yellow = Video White = Left Audio Red = Right Audio 5 YHT-23 Q U I C K -C O N N E CT G U I D E C ONNECTING A DVD P LAYER Yamaha HTR-5240 Receiver (Rear Panel) OR Digital Audio Out (Coaxial) Digital Audio Out (Optical) Video Out RCA Cable Color Codes Yellow = Video White = Left Audio Red = Right Audio V DVD Player Mixed Audio L Out L Mixed Audio R Out R Use an RCA Video Cable And Jacks For Video Interconnections DVD/LD *Analog Audio Out connections are required for playback of CD-Rs and recording from DVD to VCR. 6 YHT-23 Q U I C K -C O N N E CT G U I D E C ONNECTING A 5.1-C HANNEL DECODER If you own a 5.1-channel decoder (or a unit which incorporates a 5.1-channel decoder), you can connect its discrete outputs to the HTR-5240 as shown below. • To hear playback of a stereo or mono audio source or one encoded with Dolby Pro Logic Surround*, connect the unit (e.g., DVD player) to the DVD/LD (or SAT/D-TV) AUDIO SIGNAL input terminals. • The discrete signals feeding to the HTR-5240 cannot be recorded by a tape deck, MD recorder, or VCR. To record programs from a source (e.g., laserdisc player), connect the source unit to the DVD/LD (or SAT/D-TV) AUDIO SIGNAL input terminals. Yamaha HTR-5240 Receiver (Rear Panel) 5.1-Channel Decoder DVD Player DVD/LD EXTERNAL DECODER INPUT MAIN SUR. CNTR. L V Center Out L Subwoofer Out R SUB. Video Out Audio L Out Audio R Out Digital Audio Cable (Optical or Coaxial) R R Surround Out L Surround Out Use an RCA Video Cable And Jacks For Video Interconnections R Main Out L Main Out RCA Cable Color Codes Yellow = Video White = Left Audio Red = Right Audio *Dolby Pro Logic Surround is a trademark of Dolby Laboratories Licensing Corp. 7 YHT-23 Q U I C K -C O N N E CT G U I D E C ONNECTING A UDIO C ABLES F OR V IDEO C OMPONENTS Yamaha HTR-5240 Receiver (Rear Panel) NOTE: When using a hi-fi stereo VCR, set the Tuner/Line switch (on the VCR) to Line position to record from another source connected to the Yamaha HTR-5240 receiver. Hi-Fi Stereo VCR Audio L Out DVD or LD Player (or Video Game) Audio L Out Audio R Out Audio R Out Audio L In AUDIO SIGNAL L L R DVD/LD R SAT/D-TV IN OUT VCR Audio L Out Satellite Receiver Audio R Out Use RCA Audio Cables And Jacks For Audio Interconnections RCA Cable Color Codes Yellow = Video White = Left Audio Red = Right Audio 8 Audio R In YHT-23 Q U I C K -C O N N E CT G U I D E C ABLE H OOK -U P (B ASIC A ND PREMIUM C HANNELS ) Yamaha HTR-5240 Receiver (Rear Panel) NOTE: When using a hi-fi stereo VCR, set the Tuner/Line switch (on the VCR) to Line position to record from another source connected to the Yamaha HTR-5240 receiver. Hi-Fi Stereo VCR ANT In Basic Cable (From Wall Jack) Video In VIDEO SIGNAL Video Out Audio L Out OR Audio R Out Audio L In RCA Video Cables Audio R In IN VCR OUT L RCA Audio Cables R IN VCR OUT AUDIO SIGNAL Premium Cable (From Wall Jack) Descrambler Hi-Fi Stereo VCR (Tuner set to Channel 3 or 4) Converter Box (Channel 3 or 4 Output) ANT In Video In VIDEO SIGNAL Video Out Audio L Out Audio R Out Audio L In Audio R In RCA Video Cables IN VCR OUT L RCA Audio Cables R IN VCR OUT AUDIO SIGNAL RCA Cable Color Codes Yellow = Video White = Left Audio Red = Right Audio 9 YHT-23 Q U I C K -C O N N E CT G U I D E P ROGRAMMING T HE U NIVERSAL REMOTE C ONTROL S ETTING U P C OMPONENTS Indicator LED Component Selector Buttons Perform the procedure for each component you own. At the end of each step 5, the remote control’s processor will automatically assign the selected component’s control functions to its own buttons, ready for your use. S ETTING U P Y OUR TV Turns On Component’s Power 2. On the remote control, press TV. Use Keypad To Enter Setup Codes Use To Enter Setup Mode 1. Turn on the television set and look up a setup code for your brand of television (codes are located at the back of the HTR-5240 Owner’s Manual). Use To Enter Setup Mode 3. Press and hold both VOLUME buttons at least four seconds until the indicator LED flashes twice. 4. Using the keypad, enter the four-digit setup code. The indicator LED will flash twice after your entry. If the LED did not flash twice, repeat steps 3 and 4. The YHT-23 Home Theater package includes a universal pre-programmed remote control with factory codes to control your HTR-5240 receiver and most Yamaha audio components. To program other brands of components (i.e., TV, VCR, etc.) or if your Yamaha unit does not respond, you will need to program the remote control with the manufacturer’s codes (listed on the back pages of the HTR-5240 Owner’s Manual). NOTE: This remote control is designed to control most major brands of audio and video components. For other units, use the original remote control supplied with the product. P OWER O N 1. Load the supplied batteries into the remote control. 2. Aim the remote control at the HTR-5240, press AMP/TUNER, and then press POWER. 3. The receiver should turn on. 10 5. To verify the code works, aim the remote control at the television set, press TV, and then press POWER. The television set should turn off. If it doesn’t respond, use another code for the same manufacturer and repeat steps 3 through 5. YHT-23 Q U I C K -C O N N E CT G U I D E P ROGRAMMING T HE U NIVERSAL REMOTE C ONTROL (C ONTINUED ) S ETTING U P Y OUR C ABLE B OX ( OR DSS) S ETTING U P Y OUR DVD ( OR LD) P LAYER 1. Turn on the cable box (or DSS) and look up a setup code for your brand of cable box (or DSS) (codes are located at the back of the HTR-5240 Owner’s Manual. 1. Turn on the DVD (or LD) player and look up a setup code for your brand of DVD (or LD) player. 2. On the remote control, press DVD/LD. 2. On the remote control, press CBL/SAT. 3. Press and hold both VOLUME buttons at least four seconds until the indicator LED flashes twice. 4. Using the keypad, enter the four-digit setup code. The indicator LED will flash twice after your entry. If the LED did not flash twice, repeat steps 3 and 4. 5. To verify the code works, aim the remote control at the cable box (or DSS), press CBL/SAT, and then press POWER. The unit should turn off. If it doesn’t respond, use another code for the same manufacturer and repeat steps 3 through 5. S ETTING U P Y OUR VCR 1. Turn on the VCR and look up a setup code for your brand of VCR. 2. On the remote control, press VCR. 3. Press and hold both VOLUME buttons at least four seconds until the indicator LED flashes twice. 4. Using the keypad, enter the four-digit setup code. The indicator LED will flash twice after your entry. If the LED did not flash twice, repeat steps 3 and 4. 5. To verify the code works, aim the remote control at the DVD (or LD) player, press DVD/LD, and then press POWER. The unit should turn off. If it doesn’t respond, use another code for the same manufacturer and repeat steps 3 through 5. S ETTING U P O THER C OMPONENTS 1. Turn on the component (e.g., CD player, tape deck, or MD player) and look up a setup code for your brand of component. 2. On the remote control, press the desired component button (e.g., CD or TAPE/MD). 3. Press and hold both VOLUME buttons at least four seconds until the indicator LED flashes twice. 4. Using the keypad, enter the four-digit setup code. The indicator LED will flash twice after your entry. If the LED did not flash twice, repeat steps 3 and 4. 3. Press and hold both VOLUME buttons at least four seconds until the indicator LED flashes twice. 4. Using the keypad, enter the four-digit setup code. The indicator LED will flash twice after your entry. If the LED did not flash twice, repeat steps 3 and 4. 5. To verify the code works, aim the remote control at the component, press the appropiate component button, and then press POWER. The unit should turn off. If it doesn’t respond, use another code for the same manufacturer and repeat steps 3 through 5. 5. To verify the code works, aim the remote control at the VCR, press VCR, and then press POWER. The VCR should turn off. If it doesn’t respond, use another code for the same manufacturer and repeat steps 3 through 5. 11 YHT-23 Q U I C K -C O N N E CT G U I D E O PERATING T HE UNIVERSAL R EMOTE C ONTROL O VERVIEW R ESETTING THE R EMOTE C ONTROL TO F ACTORY C ODES The universal remote control will control up to seven different types of components (including the HTR-5240 receiver), each of which becomes active when you press a selection (e.g., TV, VCR, etc.). We can only briefly describe some functions here, and we encourage you use the HTR-5240 Owner’s Manual to gain additional experience with this powerful unit. You can reset the remote control to factory codes for all components or a desired component, as follows: P LAYING A V IDEOCASSETTE R ESETTING C ODES F OR A LL C OMPONENTS 1. Press any component selector button other than AMP/TUNER. 2. Press and hold both VOLUME buttons at least four seconds until the indicator LED flashes twice. 1. Aim the remote control at the HTR-5240, press AMP/TUNER to select the component, and then press POWER to turn the receiver on. Press VCR (i.e., 6 on the keypad) as the input for the receiver. 3. Using the keypad, enter the code “9990”. 2. Aim the remote control at the TV, press the TV to select the component, and then press POWER to turn the television on. Press TV INPUT (or A/B) to select the correct input. R ESETTING C ODES F OR A D ESIRED C OMPONENT 3. Aim the remote control at the VCR, press VCR to select the component, and then press POWER to turn the VCR on. Put a tape in the VCR, press PLAY. NOTE: At this point, the VCR controls are assigned to the remote control, since VCR was the last selected component. If you now press the VOLUME up (down) buttons, the TV/VCR volume will be raised (or lowered). To adjust the receiver’s volume, you must press AMP/TUNER to activate its functions. P LAYING A DVD 1. Aim the remote control at the HTR-5240, press AMP/ TUNER to select the component, and then press POWER to turn the receiver on. Press DVD/LD (i.e., 4 on the keypad) as the input for the receiver. NOTE: If the DVD player is connected to an external decoder, press EXT.DEC. (i.e., 9 on the keypad) as the input for the receiver. 2. Press DVD/LD and then press POWER to turn the DVD (or LD) player on. NOTE: If the DVD player is plugged into the switched ac outlet (on the back of the receiver) and its power switch was already engaged, the unit will come on each time the receiver is powered on. 3. Load a DVD (or LD) into the DVD (or LD) player. 4. Aim the remote control at the DVD (or LD) player, and press > (forward button) to start play. NOTE: The DVD player’s controls are now assigned to the remote control buttons, since DVD was the last selected component. 12 4. The indicator LED will flash twice to confirm all codes have been reset to factory values. If the LED does not flash twice, repeat steps 1 through 3. 1. Press a component selector button that matches the component you wish to reset to factory codes. 2. Press and hold both VOLUME buttons at least four seconds until the indicator LED flashes twice. 3. Using the keypad, enter the code “0000”. 4. The indicator LED will flash twice to confirm all codes have been reset to factory values. If the LED does not flash twice, repeat steps 1 through 3. 5. For your convenience, the following reference chart lists the factory codes: Component Selector Button Component Code TV CBL/DBS VCR DVD/LD CD TAPE/MD TV DBS tuner VCR DVD player CD player Tape deck 0101 0006 0002 0008 Yamaha 0005 Yamaha 0004 Yamaha ©2000 YAMAHA ELECTRONICS CORPORATION, USA 6660 Orangethorpe Avenue, Buena Park, CA 90620 PH: (714) 522-9105; FAX: (888) 435-7922 http://www.yamaha.com
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.3 Linearized : Yes Encryption : Standard V1.2 (40-bit) User Access : Print, Fill forms, Extract, Assemble, Print high-res Create Date : 2000:03:09 20:43:49 Producer : Acrobat Distiller 4.0 for Macintosh Author : Roman Creator : Adobe¨ PageMaker¨ 6.5: AdobePS 8.5.1 Title : YHT-23 Quick-Connect Modify Date : 2001:05:31 10:35:29-07:00 Page Count : 16 Page Layout : SinglePageEXIF Metadata provided by EXIF.tools