Yamaha DTXPLORER Basic Set Assembly Manual Dtxplbs En Am A0
User Manual: Yamaha DTXPLORER Basic Set Assembly Manual
Open the PDF directly: View PDF 
.
Page Count: 2
| Download | |
| Open PDF In Browser | View PDF |
CAUTION If this symbol is ignored and the equipment is used improperly, there is a danger or injury to persons handling the equipment, and material damage could occur. Watch your fingers when adjusting clamps. They may become pinched, resulting in injury. Basic Set Assembly Manual 2 Figure 4: Rack Assembly-2 Make sure you hold onto the plug, not the cable, when connecting or disconnecting the cable. Also, never place any heavy or sharp objects on the cable. Applying excessive force to the cable may result in damage to the cable, such as the wires being severed, etc. This manual describes the standard assembly of the DTXPLORER Basic Set. After assembling the parts and connecting the cords as shown in Figure 1, the unit is ready to be turned on. * To assemble the unit, make sure you have the following three packages: TP65 (Drum Pad) (5) HH65 (Hi-Hat Controller) (1) Do not use or keep the product in places with extremely high temperature (places in direct sunlight, close to a heater, in a closed car, etc.) or high humidity (bathroom, outside on a rainy day, etc.). Doing so may result in deformation, discoloration, damage or deterioration. When cleaning the product, do not use benzine, thinner or alcohol as it may result in discoloration or deformation. Please wipe with a soft cloth or a damp cloth that has been wrung out thoroughly. If the product is soiled or sticky, use a neutral detergent on a cloth then wipe with a damp cloth that has been wrung out thoroughly to remove any remaining detergent. Also pay close attention so as not to let the water and detergent come into contact with the cushions used in the product; doing so may result in deterioration. Do not attach acoustic drums to the electronic drum rack. Clamps may be damaged and drums may drop, causing injury. Checking the contents of RS40 Open the RS40 (Rack System) package and confirm the contents. Figure 2: RS40 (Rack System) RS40 (1) Fastening Screw (2) *1 KP65 (Kick Pad) (1) 3 4 5 6 7 Cable Band (10) *2 DTXPL (Drum Trigger Module) TP65 (Drum Pad) AC Adaptor HH65 (Hi-Hat Controller) PCY65 (Single-zone Cymbal Pad) RS40 (Rack System) KP65 (Kick Pad) FP6110A (Foot Pedal) 9 Assembly Manual (1) *3 - RS40 See Figure 4. Move the leg on your left (pipe ) in a clockwise direction until it is about 90 degrees from pipe with the YAMAHA logo. Tighten the two knobs loosened in step 2 and fix the position of pipe . See Figure 3 again. Loosen the knob (d) on your right. See Figure 4 again. Move the leg on your right (pipe ) in a counterclockwise direction until it is parallel with pipe . Tighten the knob loosened and fix the position of pipe . * In the following steps, loosen the knobs first, decide the position of the pipe, and then tighten the knobs. Be careful not to tighten the knobs excessively. For better performance, make minor adjustments for each part of the unit with the knobs after the assembly is completed. 8 Loosen the two knobs (e) aligned at the base of pipe , and move pipe slightly outward in a counterclockwise direction. Tighten the two knobs loosened and fix the position of pipe . Loosen the two knobs ((f) on the middle left) aligned at the base of pipe . Move pipe slightly outward in a clockwise direction. Tighten the two knobs loosened and fix the position of pipe . Loosen the two knobs ((g) on the upper left) aligned at the base of pipe , and move pipe outward in a clockwise direction until it is about 45 degrees from pipe . Tighten the two knobs loosened and fix the position of pipe . Check that the entire rack system is stable. Hold the upper area of the vertical pipe and , and shake them. If the rack system is unstable, retighten the knobs tightened in steps 2 to 5. Figure 5: Rack Assembly-3 PRECAUTIONS If this symbol is ignored and the equipment is used improperly, fatal injury to persons or serious damage could occur. Do not let small children assemble or set up this product by themselves, or they may be injured. Always assemble this product with adult supervision. Be careful with the edges of the cymbal holders and the tom holders. The sharp holder ends may result in injury. Clamp Bolt (5) PCY65 (Cymbal Pad) (2) Do not put your hands or feet under the foot pedal or foot switch. They may be pinched, resulting in injury. Figure 1: Unit Standard Assembly WARNING Open the DTPK9 (Pad Set) and Trigger Module package and confirm the contents. Figure 6: Pad Set DTLK9 Be careful around pipe ends, inside the pipe and screw ends. Metal shavings, etc. may injure your fingers. * Prepare beforehand a Phillips screwdriver, required in “ Mounting the pads and the trigger module on the rack system”. Before assembling the unit, lay a drum mat (sold separately). Before assembling the unit, lay a drum mat on the floor. Alternately, to prevent damaging your floor, lay the cardboard box of the included packages, etc. on the floor before assembling the two parts shown in the circles in Figure 1. Before using, please read this assembly manual, and use this product in a safe and proper manner. Particularly in the case of children and young users, parents or an instructor should teach the children the proper manner in which to use the device. Checking the contents of the Pad Set and the Trigger Module Do not step on or place heavy objects on the product. It may result in damage. - RS40 (Rack System) - DTLK9 (Pad Set) - DTXPL (Trigger Module) q w e r t y u i See Figure 3. Set up the rack system, with the YAMAHA logo label (a) on pipe facing the opposite side from you. Support the rack system with your right hand, and loosen the two knobs (b) and (c) on your left. FP6110A (Foot Pedal) (1) Drum Key (1) 9-channel snake cable (1) Instruction Manual (4) - TP65/65S - PCY65/65S - HH65 - KP65 Figure 7: Trigger Module *1 Use fastening screws to attach the trigger module in “ Mounting the pads and the trigger module on the rack system”. *2 Use cable bands to bind cables to pipes in “ Connecting to a power source”. (Spare bands are included.) *3 Not this manual. DTXPL (1) AC Adaptor (1) Assembling the Rack System 1 Take out the rack system from the package and remove all the cushioning. Remove the bubble wrap on the pipes while assembling the rack system. The pipe ends may injure your fingers. Figure 3: Rack Assembly-1 Be careful with the edges of the spurs attached to the base. The sharp spur ends may result in injury. If this product is used with the rack system or a cymbal stand, make sure all bolts are tightened firmly. Also, when adjusting the height or angle, do not suddenly loosen the bolts. Loose bolts may result in the rack overturning or parts dropping, causing injury. 10 See Figure 5. Loosen the knobs of the cymbal holders Always set the product on a flat and solid surface. Placement on a sloping, unstable surface or on steps may result in the product being unstable and subject to overturning. 11 When setting the product, please pay close attention to the handling and setting of cables. Carelessly placed cables may cause the user and others to trip and fall. and on the right and left (shown with on the opposite side of pipe ) and pull up the cymbal holders vertically to the height illustrated. Tighten the knobs loosened and fix the positions of the cymbal holders. Loosen the two knobs (h) aligned along the pipe with the Trigger Module attachment part . Adjust the Trigger Module attachment part so the operating panel will face upward diagonally to your side when set. Hold the Trigger Module attachment part firmly and turn it gradually. Tighten the two knobs loosened and fix the position of the Trigger Module attachment part . Do not alter the product. Doing so may result in injury or damage/deterioration to the product. Do not sit or step on the rack. The rack may overturn or be damaged, resulting in injury. * YAMAHA logo printed on pipe is facing the opposite side. Continued on the next page (on the back side) DTXPLORER_BS-set_en_0407.indd 1 2009/04/07 11:01:40 Mounting the pads and the trigger module on the rack system Mount the pads and the trigger module on the rack system. Then position the kick pad and the hi-hat. Mounting the TP65 (Drum pads) on the rack system Figure 8: Pads Assembly-1 2 Attach the PCY65 (Cymbal pad) (@4) to the cymbal holder (@1) as shown in Figure 14. Attach the felt washer (@3) and the wing nut (@2) removed in step 1, and tighten it. Turn the wing nut until you are certain that the cymbal pad is attached. The cymbal pad is designed to shake when you hit the surface, even when the wing nut is tightened securely. Figure 21: FP6110A and KP65 Figure 28: Diagram of standard connection Figure 22: T-handlet bolt Mounting the DTXPL (Trigger module) Figure 15: Pads Assembly-4 Figure 16: Module stand-1 Figure 9: TP65 @5 Module stand @6 Clamp !1 Clamp bolt !2 TP65 (Rear side) 1 Attaching the FP6110A (Foot pedal) to KP65 (Kick pad) See Figure 9. Attach the clamp bolts (!1) on TP65s (!2). Tighten the clamp bolts five to six turns each. 1 See Figure 16. Loosen the knob of the clamp (@6) (shown with stand (@5) from the clamp (@6). %1 FP6110A (Foot pedal) %2 KP65 (Kick pad) %3 T-handlet bolt 1 Turn the T-handlet bolt (%3) of the foot pedal (%1) in a counterclockwise direction and loosen it. Figure 23: Attaching FP6110A Figure 24: Adjustment ) and remove the module Figure 17: Module stand-2 Figure 10: Pads Assembly-2 %4 %5 %6 %7 @7 Fastening screw* @8 DTXPL (Rear side) * 2 Hoop clamp Convex part Beater head Pedal 2 The fastening screws are included in the same plastic bag that includes the Assembly Manual of rack system RS40. The plastic bag is packaged between the space within the cardboards used for cushioning. 3 Tighten the fastening screws (@7) with a Phillips screwdriver, as shown in Figure 17, to attach the module stand (@5) onto the rear side of the trigger module (@8). 4 Figure 18: Module stand and clamp Attach the convex part (%5) of the kick pad to the hoop clamp (%4). Turn the T-handlet bolt (%3) in a clockwise direction and tighten it. Step on the pedal and check if the head of the beater hits the center area of the kick pad. Adjust the length of the beater and/or position the pedal to the right or left if necessary. 2 Connecting to a power source Installing the HH65(Hi-hat controller) and KP65 (Kick pad) @9 DTXPL + Module stand #0 Clamp #1 Knob 2 See Figure 10. Loosen the knob (shown with ) of the tom holder on the middle left. Move the tom holder inward as shown in the close-up illustration (m). Then tighten the knob and attach the tom holder firmly at a position where it points slightly downward. Figure 11: Tom Holder and Drum Pad 3 Figure 25: Hi-Hat and KP65 1 Attach the module stand (@9) onto the clamp (#0). Tighten the knob (#1) and fix the position. If a drum mat (sold separately) is not available, lay a cardboard on the floor to prevent scratching the surface. Place the HH65 (Hi-hat controller) (^2) under the TP65 (Hi-hat cymbal) (^1). Place the KP65 (Kick pad) with FP6110A (Foot pedal) (^3) at the bottom center of the RS40 (rack system). 2 Assembling the KP65 (Kick pad) 1 If a drum mat (sold separately) is not available, lay a cardboard on the floor to prevent 3 scratching the surface. Figure 19: KP65 Assembly ^1 TP65 (Hi-hat cymbal) ^2 HH65 (Hi-hat controller) ^3 KP65 (Kick pad)+ FP6110A (Foot pedal) !3 Tom holder !4 Clamp bolt 3 4 5 6 Attach the TP65 (Drum pad) to the tom holder as shown in Figure 11. Tighten the clamp bolt and attach the drum pad TP65 firmly. See Figure 10 again. Loosen the knob (shown with ) of the tom holder on the upper left. Move the tom holder inward as shown in the close-up illustration (n). Then tighten the knob and attach the tom holder firmly at a position where it points slightly downward. Attach the TP65 (Drum pad) to the tom holder . Tighten the clamp bolt and attach the drum pad TP65 firmly. Repeat step 4 and 5 in the same manner for tom holders and at the center of the rack system and for tom holder on the right, and attach the TP65 (Drum pad) to each tom holder. Mounting the PCY65 (Cymbal pads) on the rack system Figure 12: Pads Assembly-3 Figure 13: Cymbal holder-1 Connect the AC adaptor to the DTXPL. Figure 29: Power switch (DTXPL rear panel) ON &1 Power supply jack (DC IN 12V) &2 Cable clip &3 Power switch 2 Connect the output jacks of the pad and the input jacks of the trigger module with the 9-channel snake cable. Figure 26: DTXPL (Rear panel) #3 #4 #5 #6 #7 Body Base Wing bolt Spring washer Washer 3 3 Remove the wing bolt (#5), the spring washer (#6) and the washer (#7) from the body (#3), and keep the four sets nearby in the order removed. Figure 27: 9-channel Snake Cable Use the cable bands to bind the cables to the pipes at the six points shown with the circles. * Leaving the cable slacked may interfere with your performance. Set the base (#4) on the body (#3), and attach them using the wing bolt, the spring washer and the washer removed in step 2. Assembling the FP6110A (Foot pedal) 1 If a drum mat (sold separately) is not available, lay a cardboard on the floor to prevent scratching the surface. * 1 Figure 20: FP6110A Assembly Each straight plug is labeled indicating the input jacks to which they are to be connected. Insert the straight plugs (Figure 27-(a)) of the 9-channel snake cable into the input jacks on the rear panel of the trigger module. For standard assembly, connect the straight plugs to the input jacks in accordance with the indication on each label. The assembly is now completed. * $1 $2 $3 $4 DTXPLORER_BS-set_en_0407.indd 2 Attach the AC adaptor to connect to a power source. Insert the DC plug into the power supply jack (&1) and twist the cable around the cable clip (&2) to prevent the DC plug from falling out. Figure 31: Using Cable Band Figure 14: Cymbal holder-2 @4 PCY65 (Cymbal pad) Make sure to turn the power off (the Standby/ On switch (&3) is set to the standby position). ON * If the wing bolt, the spring washer and/or the washer are separated from each other, set them as illustrated in Figure 19-(a). 1 1 Figure 30: Cable clip (DTXPL rear panel) Connecting the pads to the Trigger Module 2 @1 Cymbal holder @2 Wing nut @3 Felt washer See Figure 13. Remove the wing nut (@2) and one of the felt washers (@3) from the cymbal holder (@4). Insert the L-shaped plugs (Figure 27-(b)) of the 9-channel snake cable into each corresponding pad. It is recommended to connect the cables in order from numbers q to o shown in Figure 28 (from the shortest cable to the longest cable). 2 3 To check the actual sound, connect the unit with an amplified speaker or a headphone before turning on the power. Beater Beater locking bolt Radius rod Drum key Insert the radius rod ($3) into the hole of the frame as shown in Figure 20. Insert the beater ($1) into the hole of the beater attachment part until the further end of the beater slides outward about 15 mm. Tighten the beater locking bolt ($2) using the drum key ($4). U.R.G., Pro Audio & Digital Musical Instrument Division, Yamaha Corporation ©2009 Yamaha Corporation WS41160 ********.*-**** Printed in Indonesia 2009/04/07 11:01:44
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.6 Linearized : Yes Encryption : Standard V1.2 (40-bit) User Access : Print, Copy, Fill forms, Extract, Assemble, Print high-res XMP Toolkit : 3.1-702 Create Date : 2009:04:07 11:01:59+09:00 Creator Tool : Adobe InDesign CS4_J (6.0) Modify Date : 2009:11:27 13:21:58+09:00 Metadata Date : 2009:11:27 13:21:58+09:00 Producer : Acrobat Distiller 9.0.0 (Windows) Format : application/pdf Title : DTXPLORER Basic Set Assembly Manual Creator : U.R.G., Pro Audio & Digital Musical Instrument Division, Yamaha Corporation Description : dtxplbs_en_am_a0.pdf Document ID : uuid:24b2b70c-3f5f-413e-a8a2-87ff7400cf3a Instance ID : uuid:789666e3-35ce-49a7-951c-7c308e131bf5 Page Count : 2 Page Layout : SinglePage Subject : dtxplbs_en_am_a0.pdf Author : U.R.G., Pro Audio & Digital Musical Instrument Division, Yamaha CorporationEXIF Metadata provided by EXIF.tools