Yamaha DTXPLORER Basic Set Assembly Manual Dtxplbs En Am A0

User Manual: Yamaha DTXPLORER Basic Set Assembly Manual

Open the PDF directly: View PDF PDF.
Page Count: 2

Basic Set Assembly Manual
This manual describes the standard assembly of the DTXPLORER Basic Set.
After assembling the parts and connecting the cords as shown in Figure 1, the
unit is ready to be turned on.
* To assemble the unit, make sure you have the following three packages:
- RS40 (Rack System)
- DTLK9 (Pad Set)
- DTXPL (Trigger Module)
* Prepare beforehand a Phillips screwdriver, required in “ Mounting the
pads and the trigger module on the rack system”.
Before assembling the unit, lay a drum mat (sold separately).
Before assembling the unit, lay a drum mat on the  oor. Alternately, to prevent
damaging your  oor, lay the cardboard box of the included packages, etc. on the
oor before assembling the two parts shown in the circles in Figure 1.
Figure 1: Unit Standard Assembly
q DTXPL (Drum Trigger Module)
w TP65 (Drum Pad)
e AC Adaptor
r HH65 (Hi-Hat Controller)
t PCY65 (Single-zone Cymbal Pad)
y RS40 (Rack System)
u KP65 (Kick Pad)
i FP6110A (Foot Pedal)
Checking the contents of RS40
Open the RS40 (Rack System) package and con rm the contents.
Figure 2: RS40 (Rack System)
RS40 (1) Fastening Screw (2) *1
Cable Band (10) *2
Assembly Manual (1) *3
- RS40
*1 Use fastening screws to attach the trigger module in “ Mounting the pads and the trigger module on the rack
system”.
*2 Use cable bands to bind cables to pipes in “ Connecting to a power source”. (Spare bands are included.)
*3 Not this manual.
Assembling the Rack System
1 Take out the rack system from the package and remove all the cushioning. Remove the
bubble wrap on the pipes while assembling the rack system.
The pipe ends may injure your  ngers.
Figure 3: Rack Assembly-1
* YAMAHA logo printed on pipe is facing the opposite side.
2 See Figure 3. Set up the rack system, with the YAMAHA logo label (a) on pipe facing the
opposite side from you. Support the rack system with your right hand, and loosen the two
knobs (b) and (c) on your left.
Figure 4: Rack Assembly-2
3 See Figure 4. Move the leg on your left (pipe ) in a clockwise direction until it is about 90
degrees from pipe with the YAMAHA logo. Tighten the two knobs loosened in step 2
and  x the position of pipe .
4 See Figure 3 again. Loosen the knob (d) on your right.
5 See Figure 4 again. Move the leg on your right (pipe ) in a counterclockwise direction
until it is parallel with pipe . Tighten the knob loosened and  x the position of pipe .
* In the following steps, loosen the knobs  rst, decide the position of the pipe, and then
tighten the knobs. Be careful not to tighten the knobs excessively. For better perfor-
mance, make minor adjustments for each part of the unit with the knobs after the as-
sembly is completed.
6 Loosen the two knobs (e) aligned at the base of pipe , and move pipe slightly
outward in a counterclockwise direction. Tighten the two knobs loosened and  x the
position of pipe .
7 Loosen the two knobs ((f) on the middle left) aligned at the base of pipe . Move pipe
slightly outward in a clockwise direction. Tighten the two knobs loosened and  x the
position of pipe .
8 Loosen the two knobs ((g) on the upper left) aligned at the base of pipe , and move pipe
outward in a clockwise direction until it is about 45 degrees from pipe . Tighten the
two knobs loosened and  x the position of pipe .
9 Check that the entire rack system is stable. Hold the upper area of the vertical pipe and
, and shake them. If the rack system is unstable, retighten the knobs tightened in steps 2
to 5.
Figure 5: Rack Assembly-3
10 See Figure 5. Loosen the knobs of the cymbal holders and on the right and left
(shown with on the opposite side of pipe ) and pull up the cymbal holders vertically
to the height illustrated. Tighten the knobs loosened and  x the positions of the cymbal
holders.
11 Loosen the two knobs (h) aligned along the pipe with the Trigger Module attachment part
.
Adjust the Trigger Module attachment part so the operating panel will face upward
diagonally to your side when set. Hold the Trigger Module attachment part rmly and
turn it gradually. Tighten the two knobs loosened and  x the position of the Trigger Module
attachment part .
PRECAUTIONS
Before using, please read this assembly manual, and use this product in a safe
and proper manner. Particularly in the case of children and young users, parents
or an instructor should teach the children the proper manner in which to use the
device.
WARNING
If this symbol is ignored and the equipment is used
improperly, fatal injury to persons or serious damage could
occur.
Do not let small children assemble or set up this product by themselves, or they may
be injured. Always assemble this product with adult supervision.
Be careful with the edges of the cymbal holders and the tom holders. The sharp holder
ends may result in injury.
Be careful with the edges of the spurs attached to the base. The sharp spur ends may
result in injury.
If this product is used with the rack system or a cymbal stand, make sure all bolts are
tightened firmly. Also, when adjusting the height or angle, do not suddenly loosen
the bolts. Loose bolts may result in the rack overturning or parts dropping, causing
injury.
Always set the product on a flat and solid surface. Placement on a sloping, unstable
surface or on steps may result in the product being unstable and subject to
overturning.
When setting the product, please pay close attention to the handling and setting of
cables. Carelessly placed cables may cause the user and others to trip and fall.
Do not alter the product. Doing so may result in injury or damage/deterioration to the
product.
Do not sit or step on the rack. The rack may overturn or be damaged, resulting in
injury.
Checking the contents of the Pad Set and the
Trigger Module
Open the DTPK9 (Pad Set) and Trigger Module package and con rm the
contents.
Figure 6: Pad Set DTLK9
TP65 (Drum Pad) (5) Clamp Bolt (5)
PCY65 (Cymbal Pad) (2)
HH65 (Hi-Hat Controller) (1)
FP6110A (Foot Pedal) (1)
KP65 (Kick Pad) (1)
Drum Key (1)
9-channel snake cable (1)
Instruction Manual (4)
- TP65/65S
- PCY65/65S
- HH65
- KP65
Figure 7: Trigger Module
DTXPL (1) AC Adaptor (1)
CAUTION
If this symbol is ignored and the equipment is used
improperly, there is a danger or injury to persons handling
the equipment, and material damage could occur.
Watch your fingers when adjusting clamps. They may become pinched, resulting in
injury.
Make sure you hold onto the plug, not the cable, when connecting or disconnecting
the cable. Also, never place any heavy or sharp objects on the cable. Applying
excessive force to the cable may result in damage to the cable, such as the wires being
severed, etc.
Do not step on or place heavy objects on the product. It may result in damage.
Be careful around pipe ends, inside the pipe and screw ends. Metal shavings, etc. may
injure your fingers.
Do not put your hands or feet under the foot pedal or foot switch. They may be
pinched, resulting in injury.
Do not use or keep the product in places with extremely high temperature (places in
direct sunlight, close to a heater, in a closed car, etc.) or high humidity (bathroom,
outside on a rainy day, etc.). Doing so may result in deformation, discoloration,
damage or deterioration.
When cleaning the product, do not use benzine, thinner or alcohol as it may result in
discoloration or deformation. Please wipe with a soft cloth or a damp cloth that has
been wrung out thoroughly. If the product is soiled or sticky, use a neutral detergent
on a cloth then wipe with a damp cloth that has been wrung out thoroughly to
remove any remaining detergent. Also pay close attention so as not to let the water
and detergent come into contact with the cushions used in the product; doing so
may result in deterioration.
Do not attach acoustic drums to the electronic drum rack. Clamps may be damaged
and drums may drop, causing injury.
Continued on the next page (on the back side)
DTXPLORER_BS-set_en_0407.indd 1DTXPLORER_BS-set_en_0407.indd 1 2009/04/07 11:01:402009/04/07 11:01:40
Mounting the pads and the trigger module on the
rack system
Mount the pads and the trigger module on the rack system. Then position the
kick pad and the hi-hat.
Mounting the TP65 (Drum pads) on the rack system
Figure 8: Pads Assembly-1 Figure 9: TP65
!1 Clamp bolt
!2 TP65 (Rear side)
1 See Figure 9.
Attach the clamp bolts (!1) on TP65s (!2). Tighten the clamp bolts  ve to six turns each.
Figure 10: Pads Assembly-2
2 See Figure 10.
Loosen the knob (shown with ) of the tom holder on the middle left. Move the tom
holder inward as shown in the close-up illustration (m). Then tighten the knob and attach
the tom holder rmly at a position where it points slightly downward.
Figure 11: Tom Holder and Drum Pad
!3 Tom holder
!4 Clamp bolt
3 Attach the TP65 (Drum pad) to the tom holder as shown in Figure 11. Tighten the clamp
bolt and attach the drum pad TP65  rmly.
4 See Figure 10 again. Loosen the knob (shown with ) of the tom holder on the upper
left. Move the tom holder inward as shown in the close-up illustration (n). Then tighten the
knob and attach the tom holder rmly at a position where it points slightly downward.
5 Attach the TP65 (Drum pad) to the tom holder . Tighten the clamp bolt and attach the
drum pad TP65  rmly.
6 Repeat step 4 and 5 in the same manner for tom holders and at the center of the rack
system and for tom holder on the right, and attach the TP65 (Drum pad) to each tom
holder.
Mounting the PCY65 (Cymbal pads) on the rack system
Figure 12: Pads Assembly-3 Figure 13: Cymbal holder-1
@1 Cymbal holder
@2 Wing nut
@3 Felt washer
1 See Figure 13. Remove the wing nut (@2) and one of the felt washers (@3) from the cymbal
holder (@4).
Figure 14: Cymbal holder-2
@4 PCY65 (Cymbal pad)
2 Attach the PCY65 (Cymbal pad) (@4) to the cymbal holder (@1) as shown in Figure 14. Attach
the felt washer (@3) and the wing nut (@2) removed in step 1, and tighten it.
Turn the wing nut until you are certain that the cymbal pad is attached. The cymbal pad is
designed to shake when you hit the surface, even when the wing nut is tightened securely.
Mounting the DTXPL (Trigger module)
Figure 15: Pads Assembly-4 Figure 16: Module stand-1
@5 Module stand
@6 Clamp
1 See Figure 16. Loosen the knob of the clamp (@6) (shown with ) and remove the module
stand (@5) from the clamp (@6).
Figure 17: Module stand-2
@7 Fastening screw*
@8 DTXPL (Rear side)
*  e fastening screws are included in the same plastic bag that includes the Assembly Manual of rack system
RS40.  e plastic bag is packaged between the space within the cardboards used for cushioning.
2 Tighten the fastening screws (@7) with a Phillips screwdriver, as shown in Figure 17, to
attach the module stand (@5) onto the rear side of the trigger module (@8).
Figure 18: Module stand and clamp
@9 DTXPL + Module stand
#0 Clamp
#1 Knob
3 Attach the module stand (@9) onto the clamp (#0). Tighten the knob (#1) and  x the
position.
Assembling the KP65 (Kick pad)
1 If a drum mat (sold separately) is not available, lay a cardboard on the  oor to prevent
scratching the surface.
Figure 19: KP65 Assembly
#3 Body
#4 Base
#5 Wing bolt
#6 Spring washer
#7 Washer
2 Remove the wing bolt (#5), the spring washer (#6) and the washer (#7) from the body (#3),
and keep the four sets nearby in the order removed.
* If the wing bolt, the spring washer and/or the washer are separated from each other, set
them as illustrated in Figure 19-(a).
3 Set the base (#4) on the body (#3), and attach them using the wing bolt, the spring washer
and the washer removed in step 2.
Assembling the FP6110A (Foot pedal)
1 If a drum mat (sold separately) is not available, lay a cardboard on the  oor to prevent
scratching the surface.
Figure 20: FP6110A Assembly
$1 Beater
$2 Beater locking bolt
$3 Radius rod
$4 Drum key
2 Insert the radius rod ($3) into the hole of the frame as shown in Figure 20.
3 Insert the beater ($1) into the hole of the beater attachment part until the further end of the
beater slides outward about 15 mm. Tighten the beater locking bolt ($2) using the drum key
($4).
Attaching the FP6110A (Foot pedal) to KP65 (Kick pad)
Figure 21: FP6110A and KP65 Figure 22: T-handlet bolt
%1 FP6110A (Foot pedal)
%2 KP65 (Kick pad)
%3 T-handlet bolt
1 Turn the T-handlet bolt (%3) of the foot pedal (%1) in a counterclockwise direction and
loosen it.
Figure 23: Attaching FP6110A Figure 24: Adjustment
%4 Hoop clamp
%5 Convex part
%6 Beater head
%7 Pedal
2 Attach the convex part (%5) of the kick pad to the
hoop clamp (%4).
3 Turn the T-handlet bolt (%3) in a clockwise direction
and tighten it.
4 Step on the pedal and check if the head of the beater
hits the center area of the kick pad. Adjust the length
of the beater and/or position the pedal to the right or
left if necessary.
Installing the HH65(Hi-hat controller) and KP65 (Kick pad)
Figure 25: Hi-Hat and KP65
1 If a drum mat (sold separately) is not available,
lay a cardboard on the  oor to prevent
scratching the surface.
2 Place the HH65 (Hi-hat controller) (^2) under
the TP65 (Hi-hat cymbal) (^1).
3 Place the KP65 (Kick pad) with FP6110A (Foot
pedal) (^3) at the bottom center of the RS40
(rack system).
^1 TP65 (Hi-hat cymbal)
^2 HH65 (Hi-hat controller)
^3 KP65 (Kick pad)+ FP6110A (Foot pedal)
Connecting the pads to the Trigger Module
Connect the output jacks of the pad and the input jacks of the trigger module
with the 9-channel snake cable.
Figure 26: DTXPL (Rear panel)
ON
Figure 27: 9-channel Snake Cable
* Each straight plug is labeled indicating the input jacks to which they are to be connected.
1 Insert the straight plugs (Figure 27-(a)) of the 9-channel snake cable into the input jacks on
the rear panel of the trigger module. For standard assembly, connect the straight plugs to
the input jacks in accordance with the indication on each label.
Figure 28: Diagram of standard connection
2 Insert the L-shaped plugs (Figure 27-(b)) of the 9-channel snake cable into each
corresponding pad. It is recommended to connect the cables in order from numbers q to
o shown in Figure 28 (from the shortest cable to the longest cable).
Connecting to a power source
Connect the AC adaptor to the DTXPL.
Figure 29: Power switch (DTXPL rear panel)
ON
&1 Power supply jack (DC IN 12V)
&2 Cable clip
&3 Power switch
1 Make sure to turn the power o (the Standby/
On switch (&3) is set to the standby position).
Figure 30: Cable clip (DTXPL rear panel)
2 Attach the AC adaptor to connect to a power
source.
Insert the DC plug into the power supply jack
(&1) and twist the cable around the cable clip
(&2) to prevent the DC plug from falling out.
Figure 31: Using Cable Band
3 Use the cable bands to bind the cables to the
pipes at the six points shown with the circles.
* Leaving the cable slacked may inter-
fere with your performance.
The assembly is now completed.
* To check the actual sound, connect the unit with an ampli ed speaker or a headphone before turning on the
power.
U.R.G., Pro Audio & Digital Musical Instrument Division, Yamaha Corporation
©2009 Yamaha Corporation
WS41160 ********.*-****
Printed in Indonesia
DTXPLORER_BS-set_en_0407.indd 2DTXPLORER_BS-set_en_0407.indd 2 2009/04/07 11:01:442009/04/07 11:01:44

Navigation menu