Yi Technology YGS1817 YI Smartphone Gimbal User Manual 1
Shanghai Xiaoyi Technology Co., Ltd. YI Smartphone Gimbal 1
Users Manual
2017-11-20 V1.1 1. Getting to know the gimbal 2. How to use the gimbal Containing Bracket Telescopic Rod 1) Charging 3) Insert the camera 4) Power on and off 5) Bluetooth pairing 7) Control the gimbal You can charge YI Smartphone Gimbal through the Micro USB port, the standard charger output should be 5V/ 2A. Carefully place the phone in the containing bracket, align the securing bracket with the screws, then tighten. Attention: Secure the phone before turning on the gimbal. Press and hold the power button for 3 seconds to turn on/off the gimbal. After you’ve secured the phone to the gimbal, turn on the gimbal and then power on Bluetooth (by swiping down or go to settings on camera), short press Shutter Button on gimbal to pair. Once the pairing is complete the LED light on gimbal will flash blue for a short time. Switch in between modes. Phone Bracket Roll Motor Roll Motor Tilt Motor Telescopic Rod Pan Motor 2) Indicator 1. When charging with gimbal powered ON, the LED will flash, when charging is complete, the LED will remain on. 2. When charging with gimbal powered OFF, the LED will flash red, when charging is complete, the LED will turn green. 3. We don’t advise charging the gimbal through PC, it is too slow. 4. The gimbal has a built-in battery that should not be removed. Pan Mode Tilt and roll locked, pan axis follows the movement of the gimbal Red light Lock Mode All axis are locked Blue light Pan and Tilt Mode Roll axis locked, tilt and pan axis follow the movement of the gimbal Purple light Selfie Mode Double press (the interval should be less than 0.5s) Mode Button in any mode to enter Selfie Mode, double press again to exit 6) Control the camera 1. Double Press: Switch Mode (Photo/Video) 2. Single Press: Capture or Start/Stop Recording Pan Motor Switching modes: Joystick LED Light Power Button Shutter Button Micro USB Port Mode Button Green light 1. Single press the Mode Button: Pan Mode Lock Mode Pan and Tilt Mode Pan Mode 2. Double press the Mode Button to enter Selfie Mode, and double press again to exit selfie mode. LED Light Power Button Shutter Button Notes: 1. Pan mode is the default mode; 2. In Pan Mode and Lock Mode, long press the Mode Button to reset the angle; 3. In Selfie Mode, long press the Mode Button, the gimbal will enter into Pan Mode. Tips: How to get a smooth and stable video: hold the gimbal as stable as possible. Keep an even and smooth pace while walking and moving. Spot Shooting: to shoot a fixed object, adjust the angle to the preferred position, then switch to Lock Mode to fix gimbal’s tilt and pan axis so that spot shooting can be done properly. Thank you for choosing YI products 4. Firmware update Joystick: 1. Pan and Tilt mode: OFF 2. Lock mode: ALL 3. Pan mode: Up/ Down 9) Indicator 8) Specifications: Item Input voltage Remarks YI Action Gimbal Indicator Status Modes/Status Slow flash Low battery/charging Fast flash Battery is extremely low/Severe error 6.0V~8.4V Boot time 3 seconds Tilt axis mechanical movement range 320° Roll axis mechanical movement range 80° Vertical Pan axis mechanical movement range 320° Vertical Tilt axis following rate 3°/s ~ 70°/s Pan axis following rate 5°/s ~ 120°/s Constant on Working Blue and green light flash alternatively Gimbal in calibration Please download “YI Gimbal Tool” and firmware file from https://yitechnology.com/yigimbal/download. Offline Calibration 3. Calibration Gimbal calibration may be required in the following circumstances: 1. The tilt and roll angle is horizontal. 2. Under the lock mode, the panning angle drifts. Do not connect with USB cable when calibrating. Warning and Disclaimer Offline Calibration Turn on the gimbal, keep gimbal vertical and still then press and Horizontal hold Mode and Shutter Button at the same time, for 2 seconds to Horizontal enter calibration mode, then the gimbal will automatically complete calibration. Accelerator calibration: the indicator will flash blue and green alternately, after it’s complete, the blue indicator will remain on for 3 seconds. Gyroscope calibration: the indicator will flash blue and green alternately, after it’s complete, the blue indicator will remain on for 5 Gimbal dimension 260mm*82mm*107mm Gimbal weight 310g Compatible phong Models All Operating temperature 0 ~ 45℃ Battery life 6 ~ 8 hours 1. Please follow the user manual for installation and usage. 2. Please install the phone securely before powering on the gimbal. 3. Please charge the battery with the provided battery charger. 4. Please keep the battery away from fire and heat. 5. Any illegal use of this product is forbidden. Users are responsible for using this product in accordance with the instructions provided in both online and manual. YI Technology is not responsible for any damage caused while using this product. 6. YI Technology reserves the right to refuse service for products obtained from unofficial channels or used for unknown purposes. 7. Please contact our technical service engineers should you encounter any issues. Please note YI Technology is not responsible for improper use of the products and not reasonable, subjective judgment made by users. 8. YI Technology reserves the rights to modify the product, specifications, and manual without prior notice. seconds and enter Pan Mode. “Xiaoyi”and “YI”logo are trademarks of Shanghai Xiaoyi Technology Co.,Ltd. WARNING: No naked flame sources – such as candles – should be placed on the product. Please visit https://help.yitechnology.com to get technical support. Mode Button This device complies with Part 15 of the FCC Rules / Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Vertical B19 Vertical Under Industry Canada regulations, this radio transmitter may only operate using an antenna of a type and maximum (or lesser) gain approved for the transmitter by Industry Canada. To reduce potential radio interference to other users, the antenna type and its gain should be son chosen that the equivalent isotropically radiated power (e.i.r.p.)is not more than that necessary for successful communication. Conformément à la réglementation d’Industrie Canada, le présent émetteur radio peut fonctionner avec une antenne d’un type et d’un gain maximal (ou inférieur) approuvé pour l’émetteur par Industrie Canada. Dans le but de réduire les risques débrouillage radioélectrique à l’intention des autres utilisateurs, il faut choisir le type d’antenne et son gain de sorte que la puissance isotrope rayonnée équivalente (p.i.r.e.) ne dépasse pas l’intensité nécessaire à l’établissement d’une communication satisfaisante. CAUTION RISK OF EXPLOSION IF BATTERY IS REPLACED BY AN INCORRECT TYPE. DISPOSE OF USED BATTERIES ACCORDING TO INSTRUCTIONS. Vertical Vertical Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est autorisée aux deux conditions suivantes : (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d'en US V1.1 compromettre le fonctionnement. The device has been evaluated to meet general RF exposure requirement. The device can be used in portable exposure condition without restriction. FCC ID: 2AFIB-YGS1817 B19 小蚁相机云台 说明书(英文版) This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: - Reorient or relocated the receiving antenna - Increase the separation between the equipment and receiver - Connect the equipment into an outlet on a circuit different from that to which the receiver is connected - Consult the dealer or an experienced radio/TV technician for help Le remplacement incorrecte de la batterie est susceptible d’entraîner un risque d’explosion. Veuillez jeter les batteries usagées selon les instructions. Shutter Button Actual battery life is dependent on usage and battery capacity. Changes or modications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. 100×100mm(折页) 6099B19
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.7 Linearized : No Page Count : 1 Create Date : 2017:12:01 17:25:51+08:00 Modify Date : 2017:12:01 17:25:51+08:00 Producer : Corel PDF Engine Version 16.1.0.843 Author : wangwei Creator : CorelDRAW X6 Title : 未命名 -1EXIF Metadata provided by EXIF.tools