Yuneec Technology SR12E SR12E User Manual SR12E 20141208

Yuneec Technology Co., Limited SR12E SR12E 20141208

UserManual.wiki >

Yuneec Technology >

SR12E User Manual HTML Version

1490564R-SR12E User manual--2014-12-18

SR12EUserManual

ConnectingSR12EtoST24



PlugthecablefromFC0(flightcontrolforHX4)intoSR12Esocket,andpoweronHX4.LeanHX4

noseforwardtwicetimes,theBLUELEDofSR12Ewillflashslowly,indicatingthereceiverready

forbinding.WhenthebindingbetweenSR12EandST24completes(seethefollowinginstructions

ofBinding HX4 and ST24),theBLUELEDwillbeoff.TurnonST24,pressFPVandpress‘Take

off’.

Binding HX4 and ST24

z HX4withgimbal,cameraandLK58

Push the POWER Switch to the left side and Power on ST24→Keep HX4 nose to north, and

power on HX4 as the arrow shows →Wait until HX4 completes self-inspection, and BLUE LED

flashes→ Hold HX4 tail and lean the copter forward twice, and YELLOW LED flashes →Press

‘PAD’ →Press ‘Settings’ and find WiFi signal of LK58, choose it and enter the password, press

‘Connect’, it will show “Connected”→Press twice and back to the main interface →Press

‘FPV’ on the main screen of ST24 →Press ‘System Settings’ →Press ‘Refresh’ →Choose your

Model and Camera →Press ‘Bind’ →Press →Press ‘Take Off’ and you will hear 2 beeps,

z Lackanyoneofgimbal,cameraorLK58

Push the POWER Switch to the left side and Power on ST24→Keep HX4 nose to north, and

power on HX4 as the arrow shows →Wait until HX4 completes self-inspection, and BLUE LED

flashes→ Hold HX4 tail and lean the copter forward twice, and YELLOW LED flashes →Press

RC → Press ‘system settings’ →Press ‘Refresh’ →Choose your receiver’s code of HX4→Press

‘Bind’ →Press →Press ‘Ready’ and you will hear 2 beeps



SocketforFC0

Socketforgimbal

Antenna



SR12EBLUELEDStatus

ThreestatusforSR12EBLUELED:off,slowflash,andsolid.



‐SlowflashoftheBLUELEDindicatingthereceiverisreadytobind.

‐SolidBLUELEDindicatessmoothworkingstatusofSR12E.

‐LEDofffromslowflashstatusshowssuccessbindingbetweenSR12EandST24.

‐BLUELEDsolidturnsintoLEDoffstatusshowssignallostbetweenSR12EandST24.



FCC Statement:

ThisequipmenthasbeentestedandfoundtocomplywiththelimitsforPart15oftheFCCrules.

Theselimitsaredesignedtoprovidereasonableprotectionagainstharmfulinterferenceina

residentialinstallation.Thisequipmentgenerates,usesandcanradiateradiofrequencyenergy

and,ifnotinstalledandusedinaccordancewiththeinstructions,maycauseharmfulinterference

toradiocommunications.

However,thereisnoguaranteethatinterferencewillnotoccurinaparticularinstallation.Ifthis

equipmentdoescauseharmfulinterferencetoradioortelevisionreception,whichcanbe

determinedbyturningtheequipmentoffandon,theuserisencouragedtotrytocorrectthe

interferencebyoneormoreofthefollowingmeasures:

•Reorientorrelocatethereceivingantenna.

•Increasetheseparationbetweentheequipmentandreceiver.

•Connecttheequipmenttoanoutletonacircuitdifferentfromthattowhichthereceiveris

connected.



Thisdevicecomplieswithpart15oftheFCCrules.Operationissubjecttothefollowingtwo

conditions:

(1) Thisdevicemaynotcauseharmfulinterference,and(2)thisdevicemustacceptany

interferencereceived,includinginterferencethatmaycauseundesiredoperation.



Note:ThisequipmenthasbeentestedandfoundtocomplywiththelimitsforaClassBdigital

device,pursuanttopart15oftheFCCRules.Theselimitsaredesignedtoprovidereasonable

protectionagainstharmfulinterferenceinaresidentialinstallation.Thisequipmentgenerates,

usesandcanradiateradiofrequencyenergyand,ifnotinstalledandusedinaccordancewiththe

instructions,maycauseharmfulinterferencetoradiocommunications.However,thereisno

guaranteethatinterferencewillnotoccurinaparticularinstallation.Ifthisequipmentdoes

causeharmfulinterferencetoradioortelevisionreception,whichcanbedeterminedbyturning

theequipmentoffandon,theuserisencouragedtotrytocorrecttheinterferencebyoneor

moreofthefollowingmeasures:



—Reorientorrelocatethereceivingantenna.

—Increasetheseparationbetweentheequipmentandreceiver.

—Connecttheequipmentintoanoutletonacircuitdifferentfromthattowhichthereceiveris

connected.

—Consultthedealeroranexperiencedradio/TVtechnicianforhelp.



CAUTION:

(1) Any changes or modifications not expressly approved by the grantee of this device

could void the user's authority to operate the equipment.

(2) The modules FCC ID is not visible when installed in the host, or

(3) If the host is marketed so that end users do not have straight forward commonly

used methods for access to remove the module so that the FCC ID of the module is

visible; then an additional permanent label referring to the enclosed module: Contains

Transmitter Module FCC ID: 2ACS5-SR12E or Contains FCC ID: 2ACS5-SR12E

must be used.

RF exposure warning

·This equipment must be installed and operated in accordance with provided

instructions and the antenna(s) used for this transmitter must be installed to provide a

separation distance of at least 20 cm from all persons and must not be co-located or

operating in conjunction with any other antenna or transmitter. End-users and

installers must be provide with antenna installation instructions and transmitter

operating conditions for satisfying RF exposure compliance.

IC Radiation Exposure Statement for Canada

This device complies with Industry Canada licence-exempt RSS standard(s).

Operation is subject to the following two conditions: (1) this device may not cause

interference, and (2) this device must accept any interference, including interference

that may cause undesired operation of the device.

Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux

appareils radio exempts de licence. L'exploitation est autorisée aux deux conditions

suivantes : (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de

l'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est

susceptible d'en compromettre le fonctionnement.



Yuneec Technology SR12E SR12E User Manual SR12E 20141208

Yuneec Technology Co., Limited SR12E SR12E 20141208

1490564R-SR12E User manual--2014-12-18

Navigation menu

Namespaces

Views

Navigation