Yuneec Technology SR12E SR12E User Manual SR12E 20141208

Download:
Mirror Download [FCC.gov]
Document ID	2481968
Application ID	+ThLZJQDfLN+biwy3H7a2w==
Document Description	1490564R-SR12E User manual--2014-12-18
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	46.93kB (586591 bits)
Date Submitted	2014-12-23 00:00:00
Date Available	2014-12-25 00:00:00
Creation Date	2014-12-17 10:22:07
Producing Software	Acrobat Distiller 7.0.5 (Windows)
Document Lastmod	2014-12-17 10:22:07
Document Title	Microsoft Word - SR12E User manual--20141208.doc
Document Creator	PScript5.dll Version 5.2.2
Document Author:	yukili

SR12E User Manual
Connecting SR12E to ST24
Plug the cable from FC0(flight control for HX4) into SR12E socket, and power on HX4. Lean HX4
nose forward twice times, the BLUE LED of SR12E will flash slowly, indicating the receiver ready
for binding. When the binding between SR12E and ST24 completes (see the following instructions
of Binding HX4 and ST24), the BLUE LED will be off. Turn on ST24, press FPV and press ‘Take
off’.
Binding HX4 and ST24
z HX4 with gimbal, camera and LK58
Push the POWER Switch to the left side and Power on ST24→Keep HX4 nose to north, and
power on HX4 as the arrow shows →Wait until HX4 completes self-inspection, and BLUE LED
flashes→ Hold HX4 tail and lean the copter forward twice, and YELLOW LED flashes →Press
‘PAD’ →Press ‘Settings’ and find WiFi signal of LK58, choose it and enter the password, press
‘Connect’, it will show “Connected”→Press
twice and back to the main interface →Press
‘FPV’ on the main screen of ST24 →Press ‘System Settings’ →Press ‘Refresh’ →Choose your
→Press ‘Take Off’ and you will hear 2 beeps,
Model and Camera →Press ‘Bind’ →Press
z Lack anyone of gimbal, camera or LK58
Push the POWER Switch to the left side and Power on ST24→Keep HX4 nose to north, and
power on HX4 as the arrow shows →Wait until HX4 completes self-inspection, and BLUE LED
flashes→ Hold HX4 tail and lean the copter forward twice, and YELLOW LED flashes →Press
RC → Press ‘system settings’ →Press ‘Refresh’ →Choose your receiver’s code of HX4→Press
‘Bind’ →Press
→Press ‘Ready’ and you will hear 2 beeps
Socket for FC0
Socket for gimbal
Antenna
SR12E BLUE LED Status
Three status for SR12E BLUE LED: off, slow flash, and solid.
‐Slow flash of the BLUE LED indicating the receiver is ready to bind.
‐Solid BLUE LED indicates smooth working status of SR12E.
‐LED off from slow flash status shows success binding between SR12E and ST24.
‐BLUE LED solid turns into LED off status shows signal lost between SR12E and ST24.
FCC Statement:
This equipment has been tested and found to comply with the limits for Part 15 of the FCC rules.
These limits are designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate radio frequency energy
and, if not installed and used in accordance with the instructions, may cause harmful interference
to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment to an outlet on a circuit different from that to which the receiver is
connected.
This device complies with part 15 of the FCC rules. Operation is subject to the following two
conditions:
(1) This device may not cause harmful interference, and (2) this device must accept any
interference received, including interference that may cause undesired operation.
Note: This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment generates,
uses and can radiate radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception, which can be determined by turning
the equipment off and on, the user is encouraged to try to correct the interference by one or
more of the following measures:
—Reorient or relocate the receiving antenna.
—Increase the separation between the equipment and receiver.
—Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
—Consult the dealer or an experienced radio/TV technician for help.
CAUTION:
(1) Any changes or modifications not expressly approved by the grantee of this device
could void the user's authority to operate the equipment.
(2) The modules FCC ID is not visible when installed in the host, or
(3) If the host is marketed so that end users do not have straight forward commonly
used methods for access to remove the module so that the FCC ID of the module is
visible; then an additional permanent label referring to the enclosed module: Contains
Transmitter Module FCC ID: 2ACS5-SR12E or Contains FCC ID: 2ACS5-SR12E
must be used.
RF exposure warning
· This equipment must be installed and operated in accordance with provided
instructions and the antenna(s) used for this transmitter must be installed to provide a
separation distance of at least 20 cm from all persons and must not be co-located or
operating in conjunction with any other antenna or transmitter. End-users and
installers must be provide with antenna installation instructions and transmitter
operating conditions for satisfying RF exposure compliance.
IC Radiation Exposure Statement for Canada
This device complies with Industry Canada licence-exempt RSS standard(s).
Operation is subject to the following two conditions: (1) this device may not cause
interference, and (2) this device must accept any interference, including interference
that may cause undesired operation of the device.
Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux
appareils radio exempts de licence. L'exploitation est autorisée aux deux conditions
suivantes : (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de
l'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est
susceptible d'en compromettre le fonctionnement.

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.4
Linearized                      : Yes
XMP Toolkit                     : 3.1-701
Producer                        : Acrobat Distiller 7.0.5 (Windows)
Creator Tool                    : PScript5.dll Version 5.2.2
Modify Date                     : 2014:12:17 10:22:07+08:00
Create Date                     : 2014:12:17 10:22:07+08:00
Format                          : application/pdf
Title                           : Microsoft Word - SR12E User manual--20141208.doc
Creator                         : yukili
Document ID                     : uuid:337435a7-88f1-4921-a30c-4109e6fb4bcc
Instance ID                     : uuid:0da91d86-19eb-4429-95c4-07f15e74608a
Page Count                      : 4
Author                          : yukili

EXIF Metadata provided by EXIF.tools