Yuneec Technology SR12S Radio Controller Receiver User Manual SR12S 20140617x

Download:
Mirror Download [FCC.gov]
Document ID	2415864
Application ID	AEIdNIN+F+OrTe3pMQfqnA==
Document Description	Manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	44.14kB (551783 bits)
Date Submitted	2014-10-10 00:00:00
Date Available	2014-10-10 00:00:00
Creation Date	2014-09-16 17:51:38
Producing Software	Acrobat Distiller 10.1.0 (Windows)
Document Lastmod	2014-09-16 17:51:38
Document Title	Microsoft Word - SR12S User manual--20140617.docx
Document Creator	PScript5.dll Version 5.2.2
Document Author:	vincent

SR12S User Manual
Connecting SR12S to ST24
Plug the cable from FC0(flight control for HX4) into SR12S socket, and power on HX4. Lean HX4
nose forward twice times, the BLUE LED of SR12S will flash slowly, indicating the receiver ready
for binding. When the binding between SR12S and ST24 completes (see the following instructions
of Binding HX4 and ST24), the BLUE LED will be off. Turn on ST24, press FPV and press ‘Take
off’.
Binding HX4 and ST24
 HX4 with gimbal, camera and LK58
Push the POWER Switch to the left side and Power on ST24→Keep HX4 nose to north, and
power on HX4 as the arrow shows →Wait until HX4 completes self-inspection, and BLUE LED
flashes→ Hold HX4 tail and lean the copter forward twice, and YELLOW LED flashes →Press
‘PAD’ →Press ‘Settings’ and find WiFi signal of LK58, choose it and enter the password, press
‘Connect’, it will show “Connected”→Press
twice and back to the main interface →Press
‘FPV’ on the main screen of ST24 →Press ‘System Settings’ →Press ‘Refresh’ →Choose your
Model and Camera →Press ‘Bind’ →Press
→Press ‘Take Off’ and you will hear 2 beeps,
 Lack anyone of gimbal, camera or LK58
Push the POWER Switch to the left side and Power on ST24→Keep HX4 nose to north, and
power on HX4 as the arrow shows →Wait until HX4 completes self-inspection, and BLUE LED
flashes→ Hold HX4 tail and lean the copter forward twice, and YELLOW LED flashes →Press
RC → Press ‘system settings’ →Press ‘Refresh’ →Choose your receiver’s code of HX4→Press
‘Bind’ →Press
→Press ‘Ready’ and you will hear 2 beeps
Antenna
Socket for gimbal
Socket for FC0
SR12S BLUE LED Status
Three status for SR12S BLUE LED: off, slow flash, and solid.
‐Slow flash of the BLUE LED indicating the receiver is ready to bind.
‐Solid BLUE LED indicates smooth working status of SR12S.
‐LED off from slow flash status shows success binding between SR12S and ST24.
‐BLUE LED solid turns into LED off status shows signal lost between SR12S and ST24.
FCC Statement:
This equipment has been tested and found to comply with the limits for Part 15 of the FCC rules.
These limits
are designed to provide reasonable protection against harmful interference in a residential
installation. This
equipment generates, uses and can radiate radio frequency energy and, if not installed and used
in
accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this
equipment does
cause harmful interference to radio or television reception, which can be determined by
turning the
equipment
off and on, the user is encouraged to try to correct the interference by one or more of the
following
measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment to an outlet on a circuit different from that to which the receiver is
connected.
This device complies with part 15 of the FCC rules. Operation is subject to the following two
conditions: (1) This device may not cause harmful interference, and (2) this device must
acceptany interference received, including interference that may cause undesired operation.
Note: Modifications to this product will void the user’s authority to operate this
equipment.
IC Statement :
This device complies with Industry Canada licence‐exempt RSS standard(s). Operation is subject
to the following two conditions: (1) this device may not cause interference, and (2) this device
must accept any interference, including interference that may cause undesired operation of the
device."
IC Déclaration:
Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio
exempts de licence. L'exploitation est autorisée aux deux conditions suivantes : (1) l'appareil ne
doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage
radioélectrique subi, même si le brouillage est susceptible d'en compromettre le
fonctionnement.
Remarque: Toute modification de ce produit annule l'autorité de l'utilisateur à
utiliser cet équipement

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.5
Linearized                      : Yes
Author                          : vincent
Create Date                     : 2014:09:16 17:51:38+08:00
Modify Date                     : 2014:09:16 17:51:38+08:00
XMP Toolkit                     : Adobe XMP Core 5.2-c001 63.139439, 2010/09/27-13:37:26
Format                          : application/pdf
Creator                         : vincent
Title                           : Microsoft Word - SR12S User manual--20140617.docx
Creator Tool                    : PScript5.dll Version 5.2.2
Producer                        : Acrobat Distiller 10.1.0 (Windows)
Document ID                     : uuid:0c50c5dd-c44f-4cbb-9d8d-f2fb2d6a1875
Instance ID                     : uuid:755a5de1-7f9c-4b3a-878c-7ccce4e27d91
Page Count                      : 3

EXIF Metadata provided by EXIF.tools