Yuneec Technology ST10P Radio Controller User Manual ST10 Quick Start Guide V1 0 0422

Download:
Mirror Download [FCC.gov]
Document ID	2592711
Application ID	aaM70juub82v4IhZaTeOAQ==
Document Description	User manual(rev)
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	146.63kB (1832819 bits)
Date Submitted	2015-04-22 00:00:00
Date Available	2015-04-22 00:00:00
Creation Date	2015-04-22 11:32:57
Producing Software	Adobe PDF library 11.00
Document Lastmod	2015-04-22 11:32:57
Document Title	ST10+Quick Start Guide V1.0 0422
Document Creator	Adobe Illustrator CC 2014 (Windows)

BATTERY WARNINGS AND USAGE GUIDELINES
WARNING: Lithium Polymer (LiPo) batteries are significantly more
volatile than alkaline, NiCd or NiMH batteries. All instructions and
warnings must be followed exactly to prevent property damage and/or
serious injury as the mishandling of LiPo batteries can result in fire. By
handling, charging or using the included LiPo battery you assume all risks
associated with LiPo batteries. If you do not agree with these conditions
please return the complete product in new, unused condition to the place
of purchase immediately.
• When charging, transporting or temporarily storing the LiPo battery the
temperature range should be from approximately 40–120° F (5–49° C). Do
not store the battery or aircraft in a hot garage, car or direct sunlight. If
stored in a hot garage or car the battery can be damaged or even catch fire.
• Never leave batteries, chargers and power supplies unattended during
use.
• Never attempt to charge low voltage, ballooned/swollen, damaged or wet
batteries.
• Never allow children under 14 years of age to charge batteries.
• Never charge a battery if any of the wire leads have been damaged or
shorted.
• Never attempt to disassemble the battery, charger or power supply.
• Never drop batteries, chargers or power supplies.
• Always inspect the battery, charger and power supply before charging.
• Always ensure correct polarity before connecting batteries, chargers and
power supplies.
• Always disconnect the battery after charging.
• Always terminate all processes if the battery, charger or power supply
malfunctions.
• You must always charge the LiPo battery in a safe, well-ventilated area
away from flammable materials.
• Never charge the LiPo battery unattended at any time. When charging
the battery you must always remain in constant observation to monitor the
charging process and react immediately to any potential problems that may
occur.
• After flying/discharging the LiPo battery you must allow it to cool to
ambient/room temperature before recharging.
• To charge the LiPo battery you must use only the included charger or a
suitably compatible LiPo battery charger. Failure to do so may result in a
fire causing property damage and/or serious injury.
• If at any time the LiPo battery begins to balloon or swell, discontinue
charging or discharging immediately. Quickly and safely disconnect the
battery, then place it in a safe, open area away from flammable materials to
observe it for at least 15 minutes. Continuing to charge or discharge a
battery that has begun to balloon or swell can result in a fire. A battery that
has ballooned or swollen even a small amount must be removed from
service completely.
• Do not over-discharge the LiPo battery. Discharging the battery too low
can cause damage to the battery resulting in reduced power, flight duration
or failure of the battery entirely. LiPo cells should not be discharged to
below 3.0V each under load.
• Store the LiPo battery at room temperature and in a dry area for best
results.
IMPORTANT NOTE: It’s safer and better for the longevity of the battery to
store it only partially charged for any length of time. Storing the battery
approximately 50% charged (which is around 3.85V per cell) is typically
best, however, it will take some careful management of the charge time and
the use of a volt meter to achieve this voltage. If you have the equipment
and skills to achieve the 50% charge level for storage it is recommended. If
not, simply be sure to not store the battery fully charged whenever
possible. In fact, as long as the battery will be stored at approximately room
temperature and for no more than a few weeks before the next use, it may
be best to store the battery in the discharged state after the last flight (as
long as the battery was not over-discharged on the last flight).
CHARGING THE BATTERIES
WARNING: Lithium Ion (LiIon) and Lithium Polymer (LiPo) batteries are
significantly more volatile than alkaline, NiCd or NiMH batteries. All
instructions and warnings must be followed exactly to prevent property
damage and/or serious injury as the mishandling of LiIon/LiPo batteries
can result in fire. By handling, charging or using the included LiIon/LiPo
batteries you assume all risks associated with them. If you do not agree
with these conditions please return the complete product in new, unused
condition to the place of purchase immediately.
CHARGING THE LI-ION ST10+ BATTERY
You can charge the LiIon battery installed in the ST10+ from a 100-240V
AC outlet using the USB adapter/charger, or from a suitable USB power
source (2.0 amps max), with the USB to micro USB cable. While the ST10+
is powered off connect the cable to the USB adapter/charger, then plug it
into the USB connector/charging port on the right side. After approximately 30-45 seconds the LED indicator for the battery will blink blue while the
battery is charging, and will glow solid blue when the battery is fully
charged. It will take approximately 5.5 hours to charge a fully discharged
(not over-discharged ) battery.
ST10+ OVERVIEW
10
11
12
13
14
15
17
18
16
10
11
12
13
14
15
16
NOTE: The AC plug type will vary depending on the region in which the
product was imported/purchased (AU = Australian; EU = European; UK =
United Kingdom; US = United States).
17
18
Proportional Control Rate Slider
USB Connector/Charging Port
Audio/Earphone Jack
Take Still Photo Button
Start/Stop Motors Button
Rudder/Yaw Control (for Mode 2 and Mode 1)
Throttle/Altitude Control (for Mode 2)
Elevator/Pitch Control (for Mode 1)
5.8GHz Antenna (located inside the case)
Status Indicators (for ST10+ battery, 5.8GHz WiFi
and GPS)
2.4GHz Antenna (located inside the handle)
Start/Stop Video Recording Button
Flight Mode Selection Switch
Aileron/Roll Control (Mode 2 and Mode 1)
Elevator/Pitch Control (Mode 2)
Throttle/Altitude Control (Mode 1)
Power Switch
Volume and Navigation Touch-Activated Buttons
(Volume Down/Volume Up/Menu/Home/Back)
CGO2+ Pitch Angle/Position Control Slider
SD Card Slot (located under the battery)
ST10+ DISPLAY
The ST10+ is equipped with a touchscreen display that allows for changing various settings and viewing real-time telemetry data and streaming video during
flight.
19
18
10
17
11
16
12
15
14
13
10
11
12
13
14
15
16
17
18
19
Model Name
Frames Per Second for Video Recording Button
Status Information
Direction to Home Point
Clock/Current Time
GPS Status and Number of Satellites for ST10+
5.8GHz WiFi Video Link Status
ST10+ Battery Charge Level Status Icon
Aircraft Battery Voltage
Altitude of Aircraft (Above Ground Level)
Ground Speed of Aircraft
Distance of Aircraft from Home Point
Model Select Menu Button
Flight Settings Menu Button
System Settings Menu Button
Latitude/Longitude Position of Aircraft
Number of Satellites for Aircraft
GPS Status for Aircraft
Flight Mode of Aircraft
QUICK TIP: Double tap on the screen to increase the size of the video viewing area to full-screen and double tap again to return to the standard size).
WARNING: NEVER attempt to fly TYPHOON via First-Person View (FPV). There’s a slight ‘lag’ in the CGO2+ streaming video downlink to the ST10+, and
as a result the streaming video/FPV should only be used for aligning camera shots and not for flying! Attempting to fly via FPV can result in a crash that will
cause damage to the product, property and/or cause serious injury.
IMPORTANT NOTE: Streaming video from the CGO2+ to the ST10+ and to a separate phone/tablet (or another Yuneec transmitter/personal ground
station) at the same time is NOT recommended as it will result in a very significant lag in the video downlink.
TAKING PHOTOS AND RECORDING VIDEO
The slider located on the left side of the ST10+ allows you to set the
pitch/tilt position of the CGO2+ from approximately straight ahead (when
the slider is in the uppermost position) to approximately straight down
(when the slider is in the lowermost position). And you can easily set a
position in between by adjusting the slider accordingly.
The ST10+ seamlessly integrates control of the CGO2+ so you can easily
take still photos and start/stop video recording using the corresponding
buttons located on top:
TO TAKE A STILL PHOTO
Press the button located near the top
left corner of the ST10+. You’ll hear an
audible ‘shutter’ sound from the
ST10+ and the LED indicator on the
front of the CGO2+ will change from
glowing solid green to glowing solid
blue. It will take approximately 5
seconds to capture the photo and before you can take another still photo.
IMPORTANT NOTE: You cannot take still photos while recording video.
You MUST stop recording video in order to take still photos.
QUICK TIP: There’s an adjustable counterbalance located on the rear of
the CGO2+. This counterbalance has been adjusted at the factory to
provide the best balance and performance overall so typically it should
NOT need to be adjusted. However, if you find that the CGO2+ is making
any ‘buzzing’ sounds while powered on, carefully twist the counterbalance
in or out until the sound stops in order to achieve the best balance, performance and photo/video quality.
TO START/STOP RECORDING VIDEO
Press the button located near the top
right corner of the ST10+. You’ll hear an
audible indication from the ST10+ each
time the recording starts/stops. And
while video is recording the LED indicator on the front of the CGO2+ will flash
blue and green, and there will be a red
dot next to the time length of the recording near the upper right-hand
corner on the screen of the ST10+.
IMPORTANT NOTE: You can choose to record video at 48, 50 (PAL) or 60
(NTSC) frames per second by tapping the corresponding button near the
upper left-hand corner on the screen of the ST10+. And keep in mind that
the delay in the live video stream will be lowest at 48 and 50 as compared
to 60 frames per second.
ST10+ AND RECEIVER BINDING
Step 1) Turn on TYPHOON, and
after the Main LED Status Indicator
begins to flash blue rapidly, lift the
back end upward approximately 45°
then back down to ‘level’ two (2)
times to put the aircraft/receiver into
bind mode. The Main LED Status
Indicator will begin to the flash
orange very rapidly when the
aircraft/receiver are in bind mode.
Step 5) Tap the ‘Flight
Settings’ button, and if
required press ‘OK’ to
bypass
any
pop
up
warnings/alerts.
2 x 45+°
Step 6) Tap the ‘Bind’
button and select the
‘SR24_XXXXX’
receiver
listed in the column under
‘Model’, then tap ‘OK’ after
the connection has been
established.
Step 2) Turn on the ST10+,
and if required tap the
screen (outside of the pop
up status window) to
bypass the RC and WiFi
connection process.
SR24_16042
Step 3) Tap the ‘Model
Select’ button, and if
required press ‘OK’ to
bypass
any
pop
up
warnings/alerts.
Step 4) Select the existing
model
(for
example:
‘TYPHOON’) you would
like to bind to (or create a
‘New Model’), and if
required press ‘OK’ to
bypass
any
pop
up
warnings/alerts.
Step 7) Tap the ‘Back’
button two (2) times to
return to the main screen
and the model/receiver
should
automatically
connect to the ST10+.
ST10+ AND CGO2+ BINDING
Step 5) if required tap the
screen (outside of the pop
up status window) to
bypass the RC and WiFi
connection process, then
tap the ‘Flight Settings’
button and press ‘OK’ to
bypass
any
pop
up
warnings/alerts.
Step 1) Turn on the ST10+, and if required tap the screen (outside of the
pop up status window) to bypass the RC and WiFi connection process.
Step 2) Tap the ‘Model
Select’ button, and if
required press ‘OK’ to
bypass
any
pop
up
warnings/alerts.
Step 3) Select the existing
model
(for
example:
‘TYPHOON’) you would like
to bind to (or create a ‘New
Model’), and if required
press ‘OK’ to bypass any
pop up warnings/alerts.
CGO2_A10008
Step 4) Turn on TYPHOON
and ensure that the CGO2+
is powered on.
Step 6) Tap the ‘Bind’
button and select the
‘CGO2_XXXXXX’ camera
listed in the column under
‘Camera’, then enter the
password
‘1234567890’
when prompted and tap
‘OK’ after the connection
has b
CERTIFICATION INFORMATION
FCC STATEMENT:
This equipment has been tested and found to comply with the limits for
Part 15 of the FCC rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This
equipment generates, uses and can radiate radio frequency energy and, if
not installed and used in accordance with the instructions, may cause
harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio
or television reception, which can be determined by turning the equipment
off and on, the user is encouraged to try to correct the interference by one
or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment to an outlet on a circuit different from that to
which the receiver is connected.
This device complies with part 15 of the FCC rules. Operation is subject to
the following two conditions:
(1) This device may not cause harmful interference, and (2) this device must
accept any interference received, including interference that may cause
undesired operation.
turning the equipment off and on, the user is encouraged to try to correct
the interference by one or more of the following measures:
—Reorient or relocate the receiving antenna.
—Increase the separation between the equipment and receiver.
—Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
—Consult the dealer or an experienced radio/TV technician for help.
IC RADIATION EXPOSURE STATEMENT FOR CANADA
This device complies with Industry Canada licence-exempt RSS standard(s).
Operation is subject to the following two conditions: (1) this device may not
cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device.
Le présent appareil est conforme aux CNR d'Industrie Canada applicables
aux appareils radio exempts de licence. L'exploitation est autorisée aux
deux conditions suivantes : (1) l'appareil ne doit pas produire de brouillage,
et (2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique
subi, même si le brouillage est susceptible d'en compromettre le
fonctionnement.
This equipment complies with IC RSS-102 radiation exposure limit set forth
for an uncontrolled environment.
Cet équipement respecte les limites d’exposition aux rayonnements IC
définies pour un environnement non contrôlé.
NOTE: This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses
and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by
ST10+ Quickstart V1.0


---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.5
Linearized                      : No
XMP Toolkit                     : Adobe XMP Core 5.6-c011 79.156289, 2014/03/31-23:39:12
Format                          : application/pdf
Title                           : ST10+Quick Start Guide V1.0 0422
Metadata Date                   : 2015:04:22 11:32:57+08:00
Modify Date                     : 2015:04:22 11:32:57+08:00
Create Date                     : 2015:04:22 11:32:57+09:00
Creator Tool                    : Adobe Illustrator CC 2014 (Windows)
Thumbnail Width                 : 52
Thumbnail Height                : 256
Thumbnail Format                : JPEG
Thumbnail Image                 : (Binary data 6071 bytes, use -b option to extract)
Instance ID                     : uuid:5f9f2351-e49d-458c-b52d-f7637fba92c4
Document ID                     : xmp.did:e7931479-b205-a040-bb98-aac5d5b22aee
Original Document ID            : uuid:5D20892493BFDB11914A8590D31508C8
Rendition Class                 : proof:pdf
Derived From Instance ID        : xmp.iid:8156256a-e726-f049-acdd-f6d3fd5300a7
Derived From Document ID        : xmp.did:8156256a-e726-f049-acdd-f6d3fd5300a7
Derived From Original Document ID: uuid:5D20892493BFDB11914A8590D31508C8
Derived From Rendition Class    : proof:pdf
History Action                  : saved, converted, saved, saved, converted, saved, converted, converted, converted, converted, saved, converted, saved, saved
History Instance ID             : xmp.iid:d5794791-ca8a-44ae-8bc3-48e57849192a, xmp.iid:33ee28c3-d594-0242-b57c-b7b262a77fe9, xmp.iid:4d220b1b-14bd-4e3c-9edd-8909481219cc, xmp.iid:8c56e9a3-52cd-fd4d-90b9-74e9ab6dedfd, xmp.iid:dd77a481-94a3-624c-8c2c-48bc7aeb8367, xmp.iid:8156256a-e726-f049-acdd-f6d3fd5300a7, xmp.iid:e7931479-b205-a040-bb98-aac5d5b22aee
History When                    : 2015:02:27 17:12:50+08:00, 2015:03:11 10:47:09+08:00, 2015:03:14 15:43:52+08:00, 2015:03:19 11:25:11+08:00, 2015:04:22 11:29:24+08:00, 2015:04:22 11:31:46+08:00, 2015:04:22 11:32:53+08:00
History Software Agent          : Adobe Illustrator CC (Macintosh), Adobe Illustrator CC 2014 (Windows), Adobe Illustrator CC 2014 (Macintosh), Adobe Illustrator CC 2014 (Windows), Adobe Illustrator CC 2014 (Windows), Adobe Illustrator CC 2014 (Windows), Adobe Illustrator CC 2014 (Windows)
History Changed                 : /, /, /, /, /, /, /
History Parameters              : from application/postscript to application/vnd.adobe.illustrator, from application/postscript to application/vnd.adobe.illustrator, from application/postscript to application/vnd.adobe.illustrator, from application/postscript to application/vnd.adobe.illustrator, from application/postscript to application/vnd.adobe.illustrator, from application/postscript to application/vnd.adobe.illustrator, from application/postscript to application/vnd.adobe.illustrator
Startup Profile                 : Print
Has Visible Overprint           : True
Has Visible Transparency        : True
N Pages                         : 1
Max Page Size W                 : 210.088193
Max Page Size H                 : 140.088585
Max Page Size Unit              : Millimeters
Font Name                       : Lato-Regular, Lato-Italic, Lato-Medium, Lato-Semibold, Lato-Bold, Lato-Heavy, MyriadPro-Regular
Font Family                     : Lato, Lato, Lato, Lato, Lato, Lato, Myriad Pro
Font Face                       : Regular, Italic, Medium, Semibold, Bold, Heavy, Regular
Font Type                       : TrueType, TrueType, TrueType, TrueType, TrueType, TrueType, Open Type
Font Version                    : Version 2.010; 2014-09-01; http://www.latofonts.com/, Version 2.010; 2014-09-01; http://www.latofonts.com/, Version 2.010; 2014-09-01; http://www.latofonts.com/, Version 2.010; 2014-09-01; http://www.latofonts.com/, Version 2.010; 2014-09-01; http://www.latofonts.com/, Version 2.010; 2014-09-01; http://www.latofonts.com/, OTF 1.006;PS 001.000;Core 1.0.23;hotunix 1.28
Font Composite                  : False, False, False, False, False, False, False
Font File Name                  : Lato-Regular.ttf, Lato-Italic.ttf, Lato-Medium.ttf, Lato-Semibold.ttf, Lato-Bold.ttf, Lato-Heavy.ttf, MyriadPro-Regular.otf
Plate Names                     : Cyan, Magenta, Yellow, Black, PANTONE 172 C
Swatch Groups Colorants Tint    : 100.000000
Swatch Groups Colorants L       : 59.215698
Swatch Groups Colorants A       : 69
Swatch Groups Colorants B       : 67
Swatch Groups Group Name        : Brights
Swatch Groups Group Type        : 1
Swatch Groups Colorants Swatch Name: C=60 M=90 Y=0 K=0
Swatch Groups Colorants Mode    : CMYK
Swatch Groups Colorants Type    : PROCESS
Swatch Groups Colorants Cyan    : 60.000000
Swatch Groups Colorants Magenta : 90.000000
Swatch Groups Colorants Yellow  : 0.003100
Swatch Groups Colorants Black   : 0.003100
Producer                        : Adobe PDF library 11.00
Page Count                      : 9
Creator                         : Adobe Illustrator CC 2014 (Windows)

EXIF Metadata provided by EXIF.tools