Z Wave B00Q3N4Nt2 Kwikset Smartcode 916 Installation Guide Quick Start ENG Auto Handing NO INCLUSION Production User Manual Smart Code

User Manual: Z-Wave B00Q3N4Nt2 Kwikset Smartcode 916 Installation Guide B00Q3N4NT2_Kwikset_SmartCode_916_Installation_Guide 173 docs

Open the PDF directly: View PDF .
Page Count: 2

ENGLISH

Use and programming

instructions are located on the

reverse side of this document.

E

F

H

J

L

M

K

N

QR

P

G

A

A2

B

C

D

Parts in the Box

Latches and Strike Exterior Assembly Interior Assembly

If needed, please contact

Kwikset to order a drive-in

latch for your lock.

Kwikset

1-866-863-6584

www.kwikset.com

Required Tools

Additional Tools (depending on application)

Installation Guide

A B C

L

Install battery pack and perform door handing process

After a few seconds, the latch bolt will retract and extend on its own to learn the orientation of

the door. This is called the door handing process, and it is crucial to lock operation.

Make sure the door is open, and

insert the battery pack.

If the touchscreen indicates a failure, attempt

this procedure again.

If the door handing process is still unsuccessful

after a second attempt, consult the online

Troubleshooting Guide, available on the SmartCode

916 product page of www.kwikset.com.

Success:

ashing checkmark

symbol and single

column of digits

Failure:

ashing

“X” pattern

Once the door handing process is complete, the

touchscreen will indicate success or failure:

A

C D

B

N (2x)

KJ

Ensure tight cable

connection.

Lay excess cable at inside the

bottom of the interior housing.

Install interior assembly

align

A B C

G

M

R

K

P (3x) If needed, re-key the lock to

work with your existing key.

See the supplied SmartKey

Re-key instructions for

more information.

Make sure the door is open

and switch #2 (Auto-Lock)

is in the OFF position during

re-keying procedure.

If desired, switch #2 can be

turned back on after

re-keying is complete.

ball tip

Keep “R” in a safe place, as you will

need it to access the back panel for

additional programming.

Install the battery cover and re-key the lock

Programming

instructions are

located on the

reverse side of

this document.

Program the lock

B

D (2x)

Install strike

180°

A B

A / A2

Hold the latch in front of the

door hole, with the latch face

ush against the door edge.

If the latch holes are

centered in the door hole, no

adjustment is required.

Proceed to step 4.

If the latch holes are NOT

centered, adjust latch. See

“Latch Adjustment.”

Latch Adjustment (only if needed)

Adjust the backset of latch (if needed)

A

A2

C (2x)

A

B

C D

Install latch

For doors with chiseled edge For doors without chiseled edge

wood

block

2-1/8"

54 mm

1-1/2"

38 mm

F

F

E

Prepare exterior keypad

For doors with 2-1/8" (54 mm) holes

For doors with 1-1/2" (38 mm) holes

Install“F”

Discard “F”

A CB

D E

Q (2x)

Q (2x)

E

J

H

Q

Keep parallel to

edge of door

Tighten

screws

evenly

Insert key and test latch. If

latch does not extend or

retract smoothly, adjust

screws (Q).

Remove key when nished

and make sure the latch

bolt is fully extended.

Support exterior assembly during

mounting plate installation.

Install keypad and mounting plate

Cable goes

underneath

latch

Locate screws

(Q) and keep

them within

reach.

Route cable

through

center hole,

then push

cable into

bottom

hole.

A B C

D E

MM

K

K

L

K

AA

L

4x

Disassemble interior assembly and load battery pack

Make sure

turnpiece is in the

vertical position.

Make sure

turnpiece shaft is

rotated as shown.

Ensure correct polarity. For best

results, use new, non-rechargeable

Alkaline batteries only.

Do not install

battery pack yet!

Alarm will sound if

battery is installed

before cable is

connected.

1-3/4" (44 mm)

1-3/8" (35 mm)

2-3/8" (60 mm)

2-3/4" (70 mm)

Fold

If your door requires drilling, cut out the template and place it on the exterior side of the door.

Complete door drilling instructions are available at www.kwikset.com/doorprep.

Template

Edge

Backset

Face

Centerline

1"

25 mm

2-1/8"

54 mm

1-1/2"

38 mm

1-3/8" — 1-3/4"

35 mm — 44 mm

Check dimensions

Additional door preparation may be

required for doors with 1-1/2" (38 mm)

holes. Consult the drilling instructions

at www.kwikset.com/doorprep.

2-3/8" (60 mm)

or

2-3/4" (70 mm)

or

A / A2

Extend latch bolt

1 2

3 4 5 6

7

10

8

11

9

12

61026 / 03

ENGLISH

User Guide

Programming Codes

SmartCode at a Glance Normal Operation

Normal Operation Z-Wave & ZigBee Systems

Color Lock Status

Blinking

green Unlocked

Blinking

amber Locked

Blinking

Red Low battery

Switch Function

1Door lock status LED blinks every 6

seconds

2

Lock automatically re-locks door 30

seconds after unlocking. Disabled if no

codes are programmed.

3 Audio

4

SecureScreen feature displays random

digits to be pressed before entering

user code. This added-security feature

ensures that there are  ngerprints on all

digits so that codes cannot be identi ed

by examining the touchscreen for

 ngerprints.

Lock Inclusion

“Inclusion” refers to the process in which the lock

is added to a Z-Wave or ZigBee controller.

Initiate the Inclusion process at your ZigBee or

Z-Wave controller. Refer to your control system

instructions for more information.

Inclusion Troubleshooting

If Inclusion is unsuccessful, perform the Exclusion

process. Then repeat the Inclusion process. If

Inclusion is still unsuccessful, consult the online

Troubleshooting Guide, available on the SmartCode

916 page of www.kwikset.com.

Lock Exclusion

“Exclusion” refers to the process in which the lock

is removed from a Z-Wave or ZigBee controller.

Initiate the Exclusion process at your Z-Wave or

ZigBee controller. Refer to your control system

instructions for more information.

Z-Wave

In order to fully utilize this product, you must have a

Z-Wave controller compatible with door locks. Z-Wave is

a “Wireless mesh network,” and results may vary based

on building construction and communication path, with

35 feet+ being typical installed distance from network

controller. It may be necessary to install additional Z-Wave

beaming capable devices that can serve as repeaters to

enhance the communication path between the lock and

controller for a more robust Z-Wave network.

ZigBee

ZigBee is a “Wireless mesh network,” and results may

vary based on building construction and communication

path, with 35+ feet being typical installed distance in a

standard home environment and 250 feet+ when the

lock has a clear line of sight with the network controller. It

may be necessary to install additional ZigBee devices to

enhance the communication path between the lock and

controller for a more robust ZigBee network.

System Notes

Use the chart to determine which button to press during Inclusion and Exclusion.

System Inclusion Exclusion

Z-Wave Press button “A” once. Press button “A” once.

ZigBee Press button “A” four times. Press button “B” nine times.

Regulatory Compliance Factory Reset

A factory reset will delete all codes associated with the lock.

If needed, the door handing process can be initiated manually.

This is useful if the lock is being moved to a different door.

©2014 Kwikset Corporation

Important Safeguards

1. Read all instructions in their entirety.

2. Familiarize yourself with all warning and caution statements.

3. Remind all family members of safety precautions.

4. Restrict access to your lock’s back panel and routinely check your

settings to ensure they have not been altered without your knowledge.

5. Protect your user codes and mastercode.

6. Dispose of used batteries according to local laws and regulations.

7. For added security, turn on switch #4.

CAUTION: Prevent unauthorized entry. Since anyone with access to the

back panel can change the user codes, you must restrict access to the

back panel and routinely check the user codes to ensure they have not

been altered without your knowledge. The use of a mastercode can help

protect your system’s settings.

WARNING: This Manufacturer advises that no lock can provide complete

security by itself. This lock may be defeated by forcible or technical

means, or evaded by entry elsewhere on the property. No lock can

substitute for caution, awareness of your environment, and common

sense. Builder’s hardware is available in multiple performance grades

to suit the application. In order to enhance security and reduce risk, you

should consult a quali ed locksmith or other security professional.

A

This product complies with standards

established by the following regulatory bodies:

• Federal Communications Commission

(FCC)

• Industry Canada

FCC

This device complies with Part 15 of the FCC

Rules. Operation is subject to the following

two conditions:

( 1 ) this device may not cause harmful

interference, and

( 2 ) this device must accept any interference

received, including interference that may

cause undesired operation.

This equipment has been tested and found

to comply with the limits for a Class B

digital device, pursuant to Part 15 of the

FCC Rules. These limits are designed to

provide reasonable protection against harmful

interference in a residential installation.

This equipment generates, uses, and can

radiate radio frequency energy and, if not

installed and used in accordance with the

instructions, may cause harmful interference

to radio communications. However, there is

no guarantee that interference will not occur

in a particular installation. If this equipment

does cause harmful interference to radio or

television reception, which can be determined

by turning the equipment off and on, the

user is encouraged to try to correct the

interference by one or more of the following

measures:

• Reorient or relocate the receiving

antenna.

• Increase the separation between the

equipment and receiver.

• Connect the equipment into an outlet on

a circuit different from that to which the

receiver is connected.

• Consult the dealer or an experienced

radio/TV technician for help.

IMPORTANT! Changes or modi cations not

expressly approved by the manufacturer

could void the user’s authority to operate the

equipment.

Industry Canada

This device complies with Industry Canada

licence-exempt RSS standard(s). Operation is

subject to the following two conditions: ( 1 ) this

device may not cause interference, and ( 2 ) this

device must accept any interference, including

interference that may cause undesired operation

of the device.

B C

D

E H I

Installation instructions are

located on the reverse side

of this document.

Troubleshooting and FAQs are

available on the SmartCode 916

product page online at

www.kwikset.com.

Kwikset

1-866-863-6584

www.kwikset.com

*Beeping sound will only be heard if switch #3 is on.

2341

Switches

ON OFF

Status LED

Switches, Status LED Colors, and System Alerts Manual Door Handing

F

User Codes Requirements

Each user code must be a unique code

between 4 and 8 digits, depending on your

control system. A total of 30 user codes

may be programmed.

Programming Behavior

Successful Programming

The Checkmark symbol will illuminate and

you will hear one beep*.

Checkmark

symbol

Unsuccessful Programming

The “X” pattern will  ash three times, and

you will hear three beeps*.

“X” pattern

Programming Timeout

If the screen is not pressed for 20

seconds, the system will time out

(indicated by three beeps* and the “X”

pattern  ashing three times), and you will

need to restart the procedure.

*Beeping sound will only be heard if

switch #3 is on.

It is recommended that you add and delete

all user codes through your Z-Wave or

ZigBee control system. If your system does

not allow this, the following sections will

provide instructions for how to add and

delete codes at the lock.

aProgramming Information Enabling and Adding a Mastercode (Optional for Enhanced Security)

User codes can be programmed with or without a mastercode. Using a mastercode is an optional,

added-security measure. It is not enabled by default. A mastercode is used to add and delete user codes,

but it cannot unlock the door (unless the same code is programmed as a user code, though this is not

recommended). The mastercode must be 4-8 digits.

1324

56

Enter new

mastercode.

Press Checkmark

symbol once.

Press Lock

symbol once.

Re-enter

mastercode.

Press Lock

symbol once. Make sure the mastercode has

not been programmed already.

Attempt this procedure again,

making sure to enter the same

new mastercode in

steps 3 and 5.

Make sure switch #3 is on, and

then press the Program button

once. If you immediately hear

ve beeps and see the

Checkmark ash ve times, the

mastercode is enabled.

IF UNSUCCESSFUL TEST

Keep door open.

Press and HOLD

Program button

until Checkmark

symbol illuminates

(about 5 seconds).

Disabling and Deleting the Mastercode

32 41

675

Enter mastercode.Press Lock

symbol once.

Re-enter

mastercode.

Press Lock

symbol once.

Press Lock

symbol once. Make sure the

mastercode has been

enabled before trying

to disable it. Attempt

this procedure again,

making sure to enter

the same mastercode

in steps 4 and 6.

Make sure switch #3 is

on, and then press the

Program button once. If

you don’t immediately

hear ve beeps and see

the Checkmark ash

ve times, the

mastercode is disabled.

TEST

Press Checkmark

symbol once.

Keep door open.

Press and HOLD

Program button

until Checkmark

symbol illuminates

(about 5 seconds).

IF UNSUCCESSFUL

b

c

dAdding User Codes

Mastercode enabled:Mastercode NOT enabled:

4

2

3

1

Press Lock

button once.

Enter new USER code.

Press Checkmark

symbol once.

Keep door open.

Press Program

button once.

While the door is open and locked, test the user code

to make sure it unlocks the door.

Make sure the user code not a duplicate and that it is

between 4 and 8 digits during your next attempt.

Make sure the lock has room for an additional code. If

all user code positions are lled, delete a code to make

room for this one.

IF UNSUCCESSFUL

TEST CODE

1

3

4

5

6

Press Lock

symbol once.

Press Lock

symbol once.

You will hear ve beeps and the

checkmark will ash ve times.

Enter MASTERCODE

(the code that was

enabled in section b)

Enter new USER code.

Keep door open. Press

Program button once.

2Press Checkmark

symbol once.

While the door is open and locked, test the user code

to make sure it unlocks the door.

TEST CODE

Make sure the user code not a duplicate and that it is

between 4 and 8 digits during your next attempt.

Make sure the lock has room for an additional code. If

all user code positions are lled, delete a code to make

room for this one.

Make sure to enter a valid mastercode in step 3.

IF UNSUCCESSFUL

fDeleting All User Codes

This procedure can only be performed if the mastercode is enabled.

Note: The Auto-Lock feature (switch #2) will be disabled if all codes are deleted.

68

7

9

12

453

Press Checkmark symbol once.

Keep door open.

Press Program

button once.

Press Lock symbol once.Press Lock symbol once.

Press “9” six times. Press “9” six times.

Press Lock symbol once.

Press Lock symbol once.

Make sure to enter a valid mastercode

in step 4 during your next attempt.

You will hear ve beeps and the

checkmark will ash ve times.

While the door is open and unlocked,

press the Lock symbol. If the latch bolt

does not extend to lock, then all codes

have been successfully deleted.

Enter MASTERCODE

(the code that was

enabled in section b)

IF UNSUCCESSFUL TEST CODE

eDeleting a Single User Code

Mastercode enabled:Mastercode NOT enabled:

1

2

3

4

5

6

7

Press Lock

symbol once.

Press Lock

symbol

once.

Press Lock

symbol once.

Re-enter USER

code.

Enter USER code.

Keep door open.

Press Program

button once.

Press Checkmark

symbol once.

Make sure to enter the same valid code in steps 4

and 6.

While the door is open and locked, test the user code

to make sure it no longer unlocks the door.

IF UNSUCCESSFUL

TEST CODE

1

3

2

4

5

6

7

8

9

You will hear ve beeps and the

checkmark will ash ve times.

Keep door open. Press

Program button once.

Press Checkmark

symbol once.

Press Lock

symbol once.

Press Lock

symbol once.

Press Lock

symbol once.

Press Lock

symbol once.

Enter MASTERCODE

(the code that was

enabled in section b)

Enter USER code.

Re-enter USER

code.

Make sure to enter the same valid code in steps 6

and 8. Make sure to enter a valid mastercode in

step 4.

IF UNSUCCESSFUL

While the door is open and locked, test the user code

to make sure it no longer unlocks the door.

TEST CODE

Remove battery pack. Press and HOLD the

Program button while

reinserting the

battery pack.

Keep holding the

button for 30 seconds

until the lock beeps

and the status LED

ashes red.

Press the Program button once

more. The status LED will ash

green and red several times.

Status

LED

4 5

After a few

seconds, the lock

will initiate the

door handing

process, and the

latch bolt will

extend and

retract to learn

the orientation of

the door.

Perform the

Inclusion

process again

to add the lock

back into your

network and

controller.

12

3

System Alerts

Display Alert Reason Solution

“X” pattern  ashes one time

with one beep*. One incorrect code entered. Re-enter code.

“X” pattern  ashes three

times with three beeps*.

No user code

programmed.

Program at least one

user code.

Programming timeout after

20 seconds. Attempt programming

procedure again.

Unsuccessful programming.

“X” pattern  ashes 15 times

with 15 beeps*

Three incorrect codes

entered within one minute.

Re-enter code after 60

second touchscreen

lockout.

Checkmark and lock symbols

 ash simultaneously  ve

times with  ve beeps*.

Low battery. Replace batteries.

Checkmark and lock symbols

alternate  ashing  ve times

with  ve beeps*.

Door jammed while

attempting to lock.

Manually re-lock door. If

needed, reposition strike.

N/A Lock beeps continuously. Interior assembly is

disconnected from exterior.

Remove battery pack,

reconnect the interior to

the exterior, then replace

battery pack.

12

3

Remove battery pack. Press and HOLD the

Program button

while reinserting

the battery pack.

Release button once

battery pack is

installed. The status

LED will ash red

and green.

Press the Program

button once more.

4The latch bolt

will extend and

retract to learn

the orientation

of the door.

If the touchscreen indicates

a failure, see the online

Troubleshooting guide.

Success Failure

G

If the screen is not pressed for 20 seconds, the system will time out, and you will need to restart the procedure.

If the screen is not pressed for 20 seconds, the system will time out, and you will need to restart the procedure.

If the screen is not pressed for 20 seconds, the system will time out, and you will need to restart the procedure. If the screen is not pressed for 20 seconds, the system will time out, and you will need to restart the procedure.

If the screen is not pressed for 20 seconds, the system will time out, and you will need to restart the procedure.

1 Activate the screen.

2 If SecureScreen™ is enabled, touch the random digits that appear.

3 Enter user code.

1 Activate the screen.

2 Press Lock symbol.

Note: If no user codes are programmed, the

door cannot be locked via touchscreen.

SecureScreen is an added-security feature that

displays random digits before you enter a user code to

unlock the door. This feature ensures that there are

ngerprints on all digits so that codes cannot be

identied by examining the touchscreen for ngerprints.

If desired, this feature can be

disabled by turning switch #4

to the off position.

Activating the Screen Locking the Door

SecureScreen™

Unlocking the Door

Option 1

Touch screen with

palm or back of hand

until digits illuminate.

Option 3

Touch screen with

three or more ngers

until digits illuminate.

Option 2

Touch lower left area of screen

(where checkmark is located)

until digits illuminate.

If you press the wrong digit while entering a user code, you can press the Lock symbol

once to clear the digits entered previously and immediately restart the code entry process.

A

61026 / 03

Interior (cover removed)

Switches

Button “B”

Turnpiece

shaft

Note: When the cover is removed, the

turnpiece shaft can be used to

manually lock and unlock the door.

Back

panel

Button “A”

Program

button

Status

LED

Exterior

Lock

symbol

KeywaySmartKey

tool hole

Touchscreen

Checkmark

symbol