ZIONCOM ELECTRONICS IP04325 AC1200 Wireless Dual Band Gigabit Router User Manual

ZIONCOM ELECTRONICS (SHENZHEN) LTD. AC1200 Wireless Dual Band Gigabit Router

Contents

User Manual

Hardware InstallationQuick Installation GuideAC1200 Wireless Dual Band Gigabit RouteSuitable for:A3000RUV1.1706Information in this document is subject to change without prior notice.Copyrights by TOTOLINK All rights reserved.Website:http://www.totolink.netFor simplicity, we will take A3000RU for example throughout this guide. GPON TerminalRouterPCIPadSmart PhoneNetworkCableNetworkCableWall SocketDefault SSID2.4G: TOTOLINK_Mode No.5G: TOTOLINK_Mode No._5GConfigure the RouterConfigure the RouterInternet Settings. Connection Status shows physical connectionof router’s WAN port. Choose one Connection Type according to yourISP(Internet Service Provider).DescriptionConnection TypeNO.No configuration, simply connect the WAN port to existingEthernet port by cable. DHCPAYou’re required to enter IP Address, Subnet Mask, DefaultGateway and DNS information provided by your ISP.Static IPBYou’re required to enter User Name and Password providedby your ISP.PPPoECA.DHCP. After choose DHCP, you can go on with the 5GHz & 2.4GHz Wireless Settings.1. Please disconnect the power adapter and all cables during thunderstorm weather;2. Keep away from heat source and keep well ventilated;3. Please pay attention to the waterproofing and moisture-proof when storing, transporting and running.4. Please use the power adapter provided with the router.NOTE:B.Static IP. If you choose Static IP, please enter IP Address, Subnet Mask, Default Gateway and DNS information provided by your ISP.C.PPPoE. If you choose PPPoE, please enter the User Name and Password provided by your ISP. USB(only forA3000RU)WANLANPorts DescriptionThe DC in socket is where you will connect the power adapter. These ports connect the router to local PCs.This WAN port is where you will connect the DSL/cable modem orEthernet. This USB port is where you will connect USB device. It supportsSAMBA and DLNA service.RST Press this button for more than 5 seconds, the device will restore tofactory default settings.DC inPress this button for 2-3 seconds, WPS function enabled.WPSLED IndicatorsPower is off.Power is on.OffOnThere is no USB device connected.There is USB device connected or during data transfer.OffOnUSB(only forA3000RU)POWER(only for A950RG)After WPS button pressed, it keeps on for 2 minutes.The device is working properly.OnFlashingThe device is not powered on.OffCPU5G Wi-Fi is not enabled.5G Wi-Fi is enabled.OffOn5G2.4G Wi-Fi is not enabled.2.4G Wi-Fi is enabled.OffOn2.4GThere is device connected to the corresponding port but nodata transfer.An active device is connected to the corresponding device.OnFlashingThere is no device connected to the corresponding port.OffWANLAN 1~4Run any Web browser. Enter 192.168.0.1 in the address bar. http://192.168.0.1/Enter admin for both User Name and Password, then click LOGIN.adminNow you can see the Easy Setup page. All basic settings could be donehere, including Internet Settings and 5GHz & 2.4GHz WirelessSettings. TOTOLINK_A3000RU_5GTOTOLINK_A3000RU55G Wireless Settings. You could customize your 5GHz wirelessNetwork Name(SSID) and Password. The WPA/WPA2-PSK isrecommended for Encryption.TOTOLINK_A3000RU_5GTOTOLINK62.4G Wireless Settings. Verify or change your 2.4GHz wireless NetworkName(SSID) and Password. The WPA/WPA2-PSK isrecommended for Encryption. Click Apply.TOTOLINKTOTOLINK_A3000RUFor more information, please go to www.totolink.netConnect Wireless NetworkAfter router settings, please follow below steps to connect wireless network:2Choose the SSID that you have set on Configure the Router. Enter correctpassword. Click Connect or Next.7Wait for a few seconds, the router’s Status interface turns up, showing allconnection information.3Wireless network connected. Enjoy your Wi-Fi☺.For Mobile device users, please go to Settings—Wi-Fi to connect wireless network. What can I do if the login page does not appear?1.Check your computer’s IP address, make sure it is set to “Obtain an IP address automatically”. Steps: right click Network—Properties—Change adapter settings---Local Area Connection—Properties—Internet Protocol Version 4(TCP/IPv4).2.Make sure you enter the correct default access: 192.168.0.1. Try again.3.Use another web browser and try again.4.Reboot your router and try again.1What can I do if I cannot access the Internet?1.Check the Internet status by connecting a computer directly to the modem via Ethernet cable. If it is not working properly, contact your Internet Service Provider. 2.Setup your router again according to part 2 Configure the Router.3.Reboot your cable modem (if have) and router, then try again.2By default, TOTOLINK router don’t have any wireless network password.If you have set one, please log in to router’s Web Management page, goto 5G Wireless---Basic Settings or 2.4G Wireless --- BasicSettings to obtain or reset your password. What can I do if I forget my wireless network Password?5What can I do if I forget the router’s Web login User Nameand Password?In case you changed your router’s Login User Name and Password, wesuggest you reset your router to factory default settings by above operations. Then use the following parameters to login the router’s Web interface:Default IP address: 192.168.0.1, User Name: admin, Password: admin4How to reset the router to factory default Settings?Keep the router powered on, press the RST button on router about 10seconds, it will restore to factory default settings.3Click or icon on the right bottom of your desktop: 1WPS: press for about 1~3 seconds, the system LED indicator keep solid light, it means WPS working; RST: press for about 5~8 seconds, all LEDs blinks quickly, the device will restore to factory default settings.NOTE:After you set the Key, please remember your SSID and the Key to connect with your wireless LAN. (Frequently Asked Questions)FAQ4Connection Status PPPoE, ConnectedConnection Time 0day，0hour，0minute，0secondIP Address 164.126.106.178Subnet Mask 255.255.255.255Default Gateway 164.126.96.1DNS Server 202.96.134.133MAC Address F4:28:53:00:01:84sz83830116@163.gd●●●●●●●●●●●●●●●FCC warning: This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with theinstructions,may cause harmful interference to radio communications. However,there is no guarantee that interference will not occur in a particular installation.If this equipment does cause harmful interference to radio or television reception,which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the followingmeasures:-- Reorient or relocate the receiving antenna.-- Increase the separation between the equipment and receiver.-- Connect the equipment into an outlet on a circuit differentfrom that to which the receiver is connected.-- Consult the dealer or an experienced radio/TV technician for help.FCC Radiation Exposure Statement: This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment .This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.This equipment should be installed and operated with minimum distance 20cm between the radiator& your body.

Navigation menu