ZTE THIS IS THE FRONT COVER PAGE Advantage Air SA Catalog Rev 20140408

User Manual: ZTE AdvantageAir SA Catalog Rev 20140408

Open the PDF directly: View PDF .
Page Count: 101 [warning: Documents this large are best viewed by clicking the View PDF Link!]

TECHNICAL DATA CATALOGUE

SA.CAT.Rev.31.03.2014

2014 EDITION

COMMERICAL CATALOGUE

Technical & Product Data

Overview

The purpose of this catalogue is to aid you in making an informed decision in the selection of

air conditioning components for your project. Advantage Air has a policy of continuous

improvement therefore reserves the right to make changes, without notice, to any product or

process in this catalogue to improve performance, design, reliability or function

SA.CAT.Rev.31.03.2014

Table of Contents

FLEXIBLE DUCTWORK ..................................................................................................................... 3

SIZING GUIDE ...................................................................................................................................... 3

DUROFLEX ........................................................................................................................................... 4

ALUFLEX .............................................................................................................................................. 6

ACCOUSTIC FLEX ................................................................................................................................. 8

TEST CERTIFICATES ............................................................................................................................ 10

METAL DIFFUSERS ............................................................................................................................. 18

T-Bar Register ............................................................................................................................. 18

SWIRL OUTLETS ................................................................................................................................. 20

SUPPLY AIR GRILLES .......................................................................................................................... 32

TYPE DD ..................................................................................................................................... 37

TYPE SD ..................................................................................................................................... 42

PLASTIC DIFFUSERS & GRILLES ................................................................................................ 43

STREEMLINE RANGE .......................................................................................................................... 43

ADJUSTABLE BLADE DIFFUSER KITS ................................................................................ 43

FIXED BLADE DIFFUSER KITS .............................................................................................. 45

EGGCRATE GRILLE KITS ....................................................................................................... 47

SSRV - STREEMLINE SECURITY RELIEF VENTS ............................................................ 48

SILHOUETTE DIFFUSERS .................................................................................................................... 49

PLASTIC CUSHION HEAD ................................................................................................................... 51

ROUND DIFFUSER.............................................................................................................................. 52

SWIVEL JET DIFFUSERS ...................................................................................................................... 54

BABY LINEAR GRILLE ......................................................................................................................... 56

LINEAR ELITE DIFFUSER ..................................................................................................................... 58

AIRLINE DIFFUSER ............................................................................................................................. 60

METAL RETURN AIR GRILLES ...................................................................................................... 61

Type-RA ............................................................................................................................................. 61

PLASTIC RETURN AIR GRILLES .................................................................................................. 64

PURTECH RETURN AIR GRILLE ........................................................................................................... 64

SLIMLINE RETURN AIR GRILLE ........................................................................................................... 66

SA.CAT.Rev.31.03.2014

DOOR GRILLES................................................................................................................................. 68

TYPE-DG ............................................................................................................................................ 68

TYPE-DG-DR....................................................................................................................................... 70

EGG CRATE GRILLES ..................................................................................................................... 71

CUSTOM RANGE................................................................................................................................ 71

TYPE-ECP ........................................................................................................................................... 71

TYPE-ECA ........................................................................................................................................... 72

CORES ................................................................................................................................................ 73

WEATHER LOUVRES ...................................................................................................................... 75

Type – WPL........................................................................................................................................ 75

Type – WL .......................................................................................................................................... 76

ALUMINIUM DIFFUSION SUNDRY................................................................................................ 78

Transfer Grilles .................................................................................................................................. 78

INSULATION....................................................................................................................................... 79

DUCT BOARD INSULATION ................................................................................................................ 79

DUCT WRAP ...................................................................................................................................... 81

SONIC LINER ...................................................................................................................................... 81

DAMPERS ........................................................................................................................................... 83

OPPOSED BLADE DAMPER - Type – OBD .......................................................................................... 83

DAMPER HARDWARE ........................................................................................................................ 85

ACCESSORIES .................................................................................................................................. 89

ACCESS DOORS .................................................................................................................................. 89

AIRTURN RAIL .................................................................................................................................... 90

DUCTLOK FLANGING & FASTENERS ................................................................................................. 91

DVK VALVES ...................................................................................................................................... 93

PLASTIC EXHAUST .................................................................................................................. 93

METAL EXHAUST ..................................................................................................................... 94

SUNDRY ITEMS ................................................................................................................................ 97

NOTES ................................................................................................................................................. 99

SA.CAT.Rev.31.03.2014

FLEXIBLE DUCTWORK

SIZING GUIDE

MAXIMUM

RECOMMENDED

AIR QUANTITY

(LITRES PER SECOND)

FLEXIBLE DUCT

DIAMETER

(mm)

22 l/s

Ø 100

30 l/s

Ø 125

44 l/s

Ø 150

65 l/s

Ø 175

92 l/s

Ø 200

170 l/s

Ø 250

275 l/s

Ø 300

385 l/s

Ø 350

503 l/s

Ø 400

636 l/s

Ø 450

785 l/s

Ø 500

950 l/s

Ø 550

SA.CAT.Rev.31.03.2014

FLEXIBLE DUCTWORK

DUROFLEX

CONSTRUCTION

• Supplied in 10 metre lengths.

Core

• Core is constructed from 12 micron clear

polyester film bonded to 12 micron clear

polyester film with water based fire retardant

glue approximately 18 grams per m2

encapsulating helically wound spring steel

wire.

• The adhesives give the core a black

appearance.

Insulation

• Thick polyester blanket as specified by the

customer to comply with the BCA.

• Other insulation options available on request.

Jacket

• Inner surface 12 micron clear polyester film

bonded to 12 micron labelled metallised

polyester film with water based fire retardant

glue approximately 18 grams per m2.

APPLICATIONS

• DUROFLEX is a less expensive alternative to

aluminium duct.

• Is suitable for residential and commercial

refrigerated air conditioning, evaporative

cooling, heating and ventilation applications.

• Not recommended for return air flexible

ductwork on commercial projects, or on

systems with AC units larger than 6Hp (18kW).

TECHNICAL

DUROFLEX has been AWTA & SABS tested

and complies with the requirements of the

Building Code of Australia & South African

standards

AS 4254 & AS 1530 Part 3

DUROFLEX has passed all of the above tests

and has obtained a "0003 rating". Copies of

test certificates can be viewed on pages 10 to

Operating range

• Between -10ºC and +80 ºC

• Between -200Pa and +1000Pa internal

pressure

• Maximum velocity 20 m/s

DIMENSIONS

MODEL NO.

DIA D mm

LENGTH mm

D10

100

10000

D12

125

10000

D15

150

10000

D17

175

10000

D20

200

10000

D25

250

10000

D30

300

10000

D35

350

10000

D40

400

10000

D45

450

10000

D50

500

10000

D55

550

10000

SA.CAT.Rev.31.03.2014

FLEXIBLE DUCTWORK

DUROFLEX - PERFORMANCE

CHARACTERISTICS

SA.CAT.Rev.31.03.2014

FLEXIBLE DUCTWORK

ALUFLEX

CONSTRUCTION

• Aluflex is supplied in 10 metre lengths.

Core

• Core is constructed from 15 micron

aluminium film bonded to 15 micron aluminium

film with water based fire retardant glue

approximately 18 grams per m2 encapsulating

helically wound spring steel wire.

Insulation

• Thick polyester blanket as specified by the

customer to comply with the BCA.

• Other insulation options available on request.

Jacket

• 15 micron aluminium film bonded to 15

micron labelled aluminium film with water

based fire retardant glue approximately 18

grams per m2 .

APPLICATIONS

• Aluflex is a high quality product and is

suitable for residential and commercial

refrigerated air conditioning, evaporative

cooling, heating and ventilation applications.

• Suitable for return air flexible ductwork on

commercial applications.

TECHNICAL

Aluflex has been AWTA & SABS tested and

complies with the requirements of the Building

Code of Australia & South African standards

AS 4254& AS 1530 Part 3

Aluflex has passed all of the above tests and

has obtained a "four zero rating". Copies of

test certificates can be viewed on pages 10 to

Operating range

• Between -10ºC and +80 ºC

• Between -200Pa and +1000Pa internal

pressure

• Maximum velocity 20 m/s

DIMENSIONS

MODEL NO.

DIA D mm

LENGTH mm

A10

100

10000

A12

125

10000

A15

150

10000

A17

175

10000

A20

200

10000

A25

250

10000

A30

300

10000

A35

350

10000

A40

400

10000

A45

450

10000

A50

500

10000

A55

550

10000

SA.CAT.Rev.31.03.2014

FLEXIBLE DUCTWORK

ALUFLEX - PERFORMANCE

CHARACTERISTICS

SA.CAT.Rev.31.03.2014

FLEXIBLE DUCTWORK

ACCOUSTIC FLEX

CONSTRUCTION

• Accoustic Flex is supplied in 10 metre

lengths.

• Not a stock item and will require 10 days

lead time to manufacture & supply.

Core

• Constructed from aluminium tape on the

inside and metallised polyester tape on the

outside which encapsulates a spiral galvanised

steel wire and is chemically bonded using self

extinguishing fire retardant adhesives.

• The appearance of the core is silver with

perforations at regular intervals.

Insulation

To achieve the published insertion losses the

core must be insulated with the following

blanket:

• Thick polyester blanket as specified by the

customer to comply with the BCA.

• Other insulation options available on request.

Sleeve

• The sleeve is constructed from a silver

metallised polyester tape. As an optional extra

insulated duct can be supplied with reinforced

sleeve. This must be specified at the time of

ordering.

• The sleeve must be fully taped to the spigot

as the sleeve acts as the air envelope.

APPLICATIONS

• Accoustic flex provides higher insertion

losses than standard flexible duct and is ideal

for reducing low frequency noise levels in air

conditioning systems.

• Not recommended for return air flexible

ductwork on commercial projects, or on

systems with AC units larger than 6Hp (18kW).

TECHNICAL

Accoustic flex has passed all of the above

tests and has obtained a "0003 rating". Copies

of test certificates can be viewed on pages 10

to 17

Operating range

Accoustic flex is designed to operate in the

following range:

• Between -10ºC and +80 ºC

• Between -200Pa and +1000Pa internal

pressure

• Maximum velocity 20 m/s

DIMENSIONS

MODEL NO.

DIA D mm

LENGTH mm

AC10

100

10000

AC15

150

10000

AC20

200

10000

AC25

250

10000

AC30

300

10000

AC35

350

10000

AC40

400

10000

AC45

450

10000

AC50

500

10000

SA.CAT.Rev.31.03.2014

FLEXIBLE DUCTWORK

ACCOUSTIC FLEX

PERFORMANCE

CHARACTERISTICS

SA.CAT.Rev.31.03.2014

FLEXIBLE DUCTWORK

TEST CERTIFICATES

SA.CAT.Rev.31.03.2014

FLEXIBLE DUCTWORK

TEST CERTIFICATES

SA.CAT.Rev.31.03.2014

FLEXIBLE DUCTWORK

TEST CERTIFICATES

SA.CAT.Rev.31.03.2014

FLEXIBLE DUCTWORK

TEST CERTIFICATES

SA.CAT.Rev.31.03.2014

FLEXIBLE DUCTWORK

TEST CERTIFICATES

SA.CAT.Rev.31.03.2014

FLEXIBLE DUCTWORK

TEST CERTIFICATES

SA.CAT.Rev.31.03.2014

FLEXIBLE DUCTWORK

TEST CERTIFICATES

SA.CAT.Rev.31.03.2014

FLEXIBLE DUCTWORK

TEST CERTIFICATES

SA.CAT.Rev.31.03.2014

METAL DIFFUSERS

T-Bar Register

T-BAR REGISTER

MODEL: JM-602M REMOVABLE CORE

SPECIFICATIONS

Size: Outer frame either 595mm x 595mm metric

Neck 450mm x 450mm

Material: Pressed Metal - Steel - Powder Coated

Colour: Standard white but for large numbers we are prepared to use other colours, but there

may be a cost penalty.

ADVANTAGES

• Lightweight

• No visible joints on face

• Reduces possibility of corrosion

• Easy to clean

• Captive air system, no air leak to ceiling space

SA.CAT.Rev.31.03.2014

METAL DIFFUSERS

T-Bar Register – Performance data

450/595 4-Way ADCD

AIRFLOW

L/s

STATIC

PRESSURE

Throw (m) to terminal

velocity

CORE

m/s

NOISE

RATING

0.5 m/s

0.25 m/s

160

2.3

3.2

0.8

207

4.2

250

3.6

1.2

349

1.6

504

2.4

590

2.8

710

3.3

NOTE: * indicates throw greater than 5.5m.

SA.CAT.Rev.31.03.2014

SWIRL OUTLETS

Preliminary remarks

KRANTZ KOMPONENTEN SWIRL outlets of

the RA-N3 series have 24 fixed SWIRL vanes

and are available with square or circular face.

They generate high-quality diffuse air flow

according to the principle of turbulent mixing

ventilation. They can be installed free-hanging

from the ceiling, above open grid or expanded

metal ceilings, or flush with either closed false

ceilings or square tile ceilings.

The RA-N3 offers a very large volume flow

rate range. Using one nominal size for RA-N3

outlets within a room enables to get a uniform

ceiling design. If only a small volume flow rate

is required, a collar can be inserted in the

outlet so as to obtain the requested air flow

range; the nominal size of all ceiling-mounted

RA-N3 outlets being the same, the ceiling

design keeps its harmony. For perimeter and

corner zones it is possible to fit the outlets

(inside) with segment cover discs. These

optional discs are designed to cover certain

outlet segments so as to adapt the air

discharge direction to the room layout.

RA-N3 SWIRL outlets achieve a high level of

thermal comfort and can be used for volume

flow rates up to 400 l/s [1440 m3/h] at

temperature differences up to –12 K when

cooling and +10 K when heating for ceiling

heights up to 3 m (> 3 m = +5 K).

Range of application

Size

Collar

Volume flow rate

l/s m3/h

Max. temperature

difference supply

air–indoor

air

355

56 – 175

200 – 630

–12 K when cooling

+10 K when heating

(£ 3 m)

+ 5 K when heating

(> 3 m)

38 – 122

135 – 440

26 – 89

95 – 320

500

125 – 400

450 – 1440

86 – 280

310 – 1010

61 – 200

220 – 720

Mode of operation

The SWIRL outlet 1 discharges the supply air

in the horizontal direction, this feature being

enhanced by the special shape of the exit 1a.

The high-turbulence supply air jets induce a

large proportion of indoor air, which leads to

the fast equalization of supply air and indoor

air temperatures as well as to a rapid decrease

in jet velocity.

Thanks to its stable supply air distribution

pattern at low sound power levels this outlet

can be used for a very wide range of air

volume flow rates. Inserting a collar in the

outlet enables to additionally vary the flow rate

range.

Construction design

The RA-N3 is available in 2 nominal sizes: DN

355 and DN 500. The circular model is fitted

on the outside with a flush contact edge for

ceiling attachment (see detail Y on page 4).

The outlet with square face has a 90° turn-up

for installation in square tile ceilings (see detail

Z on page 4).

Both outlet models are made from powder-

coated sheet metal and are fastened to the

reducer or connection box with a central screw

5 whose head is concealed by a cap 5a having

the same powder coating as the outlet.

Installation options

The following connection types with related

accessories are available for connecting the

outlet to the duct system.

Connection type A, with reducer for connection

to a circular duct or a flexible duct

SA.CAT.Rev.31.03.2014

SWIRL OUTLETS

Connection type D, with connection box for a

closed ceiling

Connection type F, with connection box for a

square tile ceiling

Connection type A The ‘A’ reducer is fitted

with 3 suspension brackets staggered by 90°,

for fixing to the ceiling, as well as with a screw

nut for the central fastening of the outlet. The

reducer can be connected to a spiral seam

duct or to a flexible duct. For installation in a

closed false ceiling upon completion of said

ceiling, the SWIRL outlet with flush contact

edge shall be inserted into the reducer

through the ceiling cutout and screwed up.

Connection type D The RA-N3 outlet is

connected to a circular duct via the lateral

spigot of a flat connection box. This

connection type is suitable for outlets to be

installed above open or closed false ceilings.

The connection box is fitted with 4 suspension

brackets for fixing to the ceiling and a screw

nut for the central fastening of the outlet. The

optional volume flow damper positioned in

the lateral connection spigot can be adjusted

through the openings of the SWIRL outlet. As

an option, this connection box can be fitted

with acoustic lining.

Connection type F This connection type is

particularly suitable for square tile ceilings.

The square SWIRL outlet with connection box

is inserted into the ceiling from the top in

place of a ceiling tile. The connection box is

fixed to the load-bearing ceiling and the outlet

is screwed to the connection box.

SWIRL outlets installed above an open grid

ceiling. The return air is removed evenly

through the whole ceiling surface and

extracted by the main return air duct

positioned immediately above the outlets.

SA.CAT.Rev.31.03.2014

SWIRL OUTLETS

Sketches of installation options

SA.CAT.Rev.31.03.2014

SWIRL OUTLETS

Dimensions of connection type A

SA.CAT.Rev.31.03.2014

SWIRL OUTLETS

Dimensions of connection types D and F

SA.CAT.Rev.31.03.2014

SWIRL OUTLETS

Comfort criteria and minimum air outlet centre spacing

Comfort criteria

The layout of the outlet will be based on compliance

with the required maximum permissible indoor air

velocities1). First you have to determine the

maximum specific volume flow rate V. Sp max

depending on the indoor air velocity u and the

discharge height H as per Graph 1. The minimum

outlet centre spacing tmin will then be determined

according to Graph 2 on the basis of the maximum

specific volume flow rate and the outlet volume flow

rate.

Maximum specific volume flow rate

Minimum air outlet centre spacing

SA.CAT.Rev.31.03.2014

SWIRL OUTLETS

Layout sheet for connection type A

SA.CAT.Rev.31.03.2014

SWIRL OUTLETS

Layout sheet for connection type D and F

SA.CAT.Rev.31.03.2014

SWIRL OUTLETS

Sound power level and insertion loss

SA.CAT.Rev.31.03.2014

SWIRL OUTLETS

Sound power level and total pressure loss

SA.CAT.Rev.31.03.2014

SWIRL OUTLETS

Features

 For high-quality diffuse indoor air flow.

 Available with square. 1) or circular face

 Stable supply air jets. 2) even at minimum volume flow rate

 Available in 2 sizes: DN 355 and DN 500, each with . 3 volume flow rate ranges (depending on

collar 0, 2, or 4)

 Very large volume flow rate range, which enables a uniform ceiling design due to the use of one

outlet size within a room.

 Discharge height from 2.4 to 4.5 m .

 Maximum temperature difference between supply air and indoor air: –12 K when cooling, +5 K

when heating (+10 K up to 3 m ceiling height)

 Low sound power level and pressure loss.

 Installation free-hanging from the ceiling, above open grid ceilings, or in closed ceilings

 Outlet element easy to mount and demount from the room

 Box for connection type F is stackable, i.e. low transport and storage volume

 Outlet element made from powder-coated sheet metal, connection box made from Sendzimir

galvanized sheet metal

 Segment cover discs (optional) enable to adapt the air discharge to the room layout (3-way

discharge, 2-way discharge symmetric or asymmetric); these discs can be turned any time upon

outlet installation

SA.CAT.Rev.31.03.2014

SWIRL OUTLETS

Type code and tender text

Tender text

..... units

SWIRL outlet for high-quality indoor air

flow at minimal temperature gradients in

the occupied zone, consisting of:

– low-height outlet element with spigot,

specially shaped face, SWIRL vanes –

vane underside flush with surround-ing

outlet face – and central fastening screw

with cap; outlet face is round or square

– optional V. collars to increase the range

of volume flow rates

– optional segment cover discs for 3-way

discharge or 2-way symmetric or

asymmetric discharge 2)

– optional aluminium reducer (connection

type A) with lateral suspension brackets

and screw nut for central fastening of

outlet

– optional connection box in flat design

with screw nut for central fastening of

outlet, with lateral suspension brackets

and connection spigot, box design:

SWIRL

outlet with round or square face,

optionally fitted with V. damper

adjustable from room side and/or

acoustic lining.

SWIRL

outlet with square face, optionally fitted

with V. damper adjustable from room

side.

Materials:

SWIRL outlet made from sheet metal

powder-coated to RAL 9010 3).

Reducer made from aluminium.

Connection box made from galvanized

sheet metal.

Make: KRANTZ KOMPONENTEN

Type: RA-N3 – __ – DN ___ / __ / __ – __

__ __ – ____

Subject to technical alteration.

1) Square face with 90° turn-up (12 mm) for

square tile ceilings on enquiry

2) The segment cover discs can be turned so

as to adapt the air discharge direction to

the room layout

3) Other colour on enquiry

SA.CAT.Rev.31.03.2014

SUPPLY AIR GRILLES

Details

SELECTION OF SUPPLY GRILLES

AND REGISTERS

• The performance data which follows

permits quick, easy, and accurate selection

of supply grilles and registers.

• Two groups of data are required for

selection.

• Inherently required by the structural and

room use considerations.

• The required performance characteristics of

the supply outlets.

• Consider first the spaces which are to be

conditioned and their effects upon outlet

selections.

1. m3/s The air volume to be delivered to

each space is determined by overall

system design, and the m3/s per outlet is

determined by the number of outlets which

supply each space.

2. NC Level The permissible sound level in

each space may be specified by the owner

or the architect, or it may be determined as

an engineering design goal. Figure 1

contains an abbreviated list of design goals

for air conditioning sound control in

common occupancies.

3. Throw Requirement The required throw is

determined from the building plan. Often

the throw requirement will be the distance

from the outlet to the opposite wall.

Sometimes it will be the distance from the

outlet to the intersection of its air system

with air being delivered from another supply

outlet.

• Other items to be considered are the

spread requirement, permissible drop, and

acceptable pressure drop.

• The air stream should spread sufficiently so

that the wall or space at the end of the

throw is blanketed.

• The drop of the air stream should not be so

great that it is within 1.5m of the floor at the

end of the throw.

• Finally, the allowance in the design of the

system for outlet pressure loss should not

be exceeded.

• After the design requirements - air flow, NC

level, throw spread, and drop requirements

– are known, the outlet can be selected

Selection of Grilles and Registers -

19mm Louvers

• The basic selection data are given in the

Tables to follow for grilles and registers having

louvers on a 19mm spacing.

• For each listed air volume, the static

pressure drop and two values of throw are

given for each grille area factor.

• The minimum throw is the distance the air

will travel to a terminal velocity of 0.64m1s; the

maximum throw is the distance of air travel to

a terminal velocity of 0.41m1s.

• For each m3/s and the grille size, selection

data are given at three spread angles -0°,

22½° and 45°.

• NC level is coded in 5 db increments for each

m3/s, spread angle, and area factor in the

table.

SA.CAT.Rev.31.03.2014

SUPPLY AIR GRILLES

Details

TABLE 5 - RECOMMENDED NC

LEVEL DESIGN GOALS

• The area factor shown at the top of each

column is the key to actual grille-size

selection.

• The Grille Sizes shown are not the only

grilles which could be selected.

• Complete size selection is given, in Tables

6, 7 & 8 to follow, which relates grille height

and grille width to the area factor.

• Selecting a register requires that the effects

of dampers on grille performance be

considered.

• Throw, spread, and drop are not affected by

the dampers of a register - if the damper is

wide open - but the pressure requirement

and the sound level generated by a register

are different from those of a grille only.

• The effects of the damper on these

performance characteristics are shown in

Table 6 to follow.

• To obtain the NC level of a register add the

"NC addition" factor to the NC level of the

grille as determined from Tables 6 & 9 to

follow.

• To obtain the static pressure loss of the

by the "Ps multiplier" of the damper.

• Note these two factors vary with grille width.

Drop

• The drop of a cooled air stream is shown in

Table 7. This is the vertical distance which

the air will have dropped as it travels

across the room and slows to a velocity of

0.6mJs.

• Note that, at a constant air flow, the drop

increases as the grille area factor

increases.

• This occurs because the air velocity at the

grille face decreases as the grille area

increases.

• On the other hand, it must be realized that

the further the air travels - that is: the

longer the throw - the greater the drop

becomes.

• For this reason, drop increases as air flow

is increased if the grille size and spread

angle are kept constant.

• The spread angle setting affects all of the

performance characteristics of a grille.

• The following general rules can be used to

estimate the spread:

1. For 0° spread angle, the total spread of

the air stream is one-third of the throw.

2. For 22½° spread angle, the total spread of

the air stream is about 45 percent of the

throw.

3. For 45° spread angle, the total spread of

the air stream is 1.5 times the throw.

• These values are the total spread of the air

stream, but they do not consider grille width

which should be added to the spread

estimated above.

SA.CAT.Rev.31.03.2014

SUPPLY AIR GRILLES

Details

If three grilles serve the space, determine the difference between the combined NY level for the fIrst

two grilles and the NC level of the third grille. Determine the NC addition as above, and add this to the

combined NC level of the first two units. If the difference between NC levels of two grilles is 10 db or

more, the sound generated by the quieter grille will not affect the space NC.

TABLE 6 - NC AND STATIC PRESSURE FACTORS FOR REGISTERS (OPEN DAMPER)

NOTES: (1) NC Addition plus grille NC equals register NC level.

(2) Ps Multiplier times grille static pressure equals register static pressure

TABLE 7 - DROP OF COOLED SUPPLY AIR

• For larger spaces and specific room absorption conditions, a calculation using sound power level

data is required.

• Closing the damper of a register results in:

• The restriction of the air flow, thereby increasing the pressure drop and decreasing the air flow.

• The damper generating sound - increases the NC level.

• For example a damper closed sufficiently to double the pressure loss of a register (pressure ratio of

2) causes and NC increase of about 7 db. (As a rule of thumb - and for general reference only - it

can be assumed that closing an opposed blade damper to an effective opening ratio of 70 percent

doubles the pressure loss of the damper outlet combination. Closing the damper to an effective

opening ratio of fifty percent increases the pressure loss to 4-times the grille-open damper loss.)

SA.CAT.Rev.31.03.2014

SUPPLY AIR GRILLES

Details

Combining Sound Sources

• The NC data for registers and grilles, given in tables to follow, contain an allowance for the sound

adsorbing properties of the average room and its contents.

• This absorption is assumed to be 8 db.

• For relatively small spaces - about 73.5 sq m. or less of floor area and ceiling height of 3.0m or

less – the following simplified method for estimating NC level produced by combinations of supply

and return registers and grilles can be used:

1. Determine the difference in NC level between the grilles or registers having the highest NC and

the second highest NC level.

2. From table 9 to follow determine the number of decibels to be added to the NC level of the grille

having highest NC level. This sum is the combined NC level generated by the two grilles or

registers.

TABLE 8 AREA FACTORS, FOR SELECTION OF SUPPLY GRILLES - 19mm, SD AND DD

SA.CAT.Rev.31.03.2014

SUPPLY AIR GRILLES

Details

TABLE 9 - NC ADDITION FOR COMBINING EFFECTS OF SOUND SOURCES

Selection of Grilles and Registers - 19mm Blade Spacing

• Grilles and registers having louvers (blades) on 19mm spacing are selected in a similar manner.

• The structural and room-use factors, the air volume, and the throw, spread drop and NC

requirements must be considered in the same way as with other grilles and registers.

• For each listed air volume, the static pressure and two values of throw are given.

• The minimum throw is the distance the air will travel to a terminal velocity of 0.64m/2; the

maximum throw is the distance of air travel to a terminal velocity of 0.41m/s.

• Selection data are given at each of three spread angles - 0°, 22½°, and 45° - and for NC level in 5

db increments.

• The area factor shown at the top of each column permits flexibility in grille-size selection

SA.CAT.Rev.31.03.2014

SUPPLY AIR GRILLES

Details

TYPE DD: Double deflection supply air grilles

manufactured of extruded type 50S

anodising grade aluminium with individually

adjustable front vertical and rear horizontal

louvres held in place by starlock washers

and spring wire.

Optional

Accessories OBD = Opposed Blade Damper

CF = Concealed Fixing

Frame Options 30mm Standard

20mm

50mm

Finish Options NA = Natural Anodised

EPC = Epoxy Powder Coating

WS = Wet Spray Colour

Note: (1) Dimensions given are for opening size into which grille will fit (i.e Normal Duct Size)

(2) If code "OS" is entered under SPECIAL INSTRUCTIONS, then dimensions given are over

flange.

SA.CAT.Rev.31.03.2014

SUPPLY AIR GRILLES

Performance Data DD – SD

SA.CAT.Rev.31.03.2014

SUPPLY AIR GRILLES

Performance Data DD – SD

SA.CAT.Rev.31.03.2014

SUPPLY AIR GRILLES

Type DD

• The two sets of individually adjustable louvers - vertical and horizontal - with or without a damper

attached, allow these grilles to provide maximum flexibility of adjustments for spread and throw

requirements.

• The multi directional flexibility allows for multi-directional air supply.

• They are recommended for high sidewall, bulkhead or duct mounting and can be used for heating,

cooling, or ventilating applications

GENERAL SPECIFICATIONS

• All models feature two sets of individually adjustable blades - vertical and horizontal - spaced at

19mm apart, and fitted into a 32.5 or 20mm frame.

• The optional opposed blade damper is constructed using extruded aluminium blades and frame.

• The individual blades are secured by corrosion resistant star lock washers with added adjusting

tension supplied by corrosion resistant spring wire.

• All models can be furnished with powder coated white finish preceded by five stage preparation

process of cleaning, phosphatising and drying.

• Grilles can be supplied in natural anodised and white powder coated finishes.

• Other colours are available on request.

SA.CAT.Rev.31.03.2014

SUPPLY AIR GRILLES

Type SD

• These models have one set of individually adjustable blades on a horizontal plane to provide

maximum throw requirements or on a vertical plane (on special request) to provide maximum

spread adjustment.

• They are recommended for heating, cooling, and ventilating applications, generally mounted in a

high sidewall, bulkhead or duct when either spread or throw only is important.

• The grilles are provided with or without an opposed blade damper.

• The adjustable blades are spaced at 19mm, but fixed blades with 13, 21 and 26mm spacing can

be offered at special request.

GENERAL SPECIFICATIONS

• All models feature one set of individually adjustable blades of extruded aluminium set in a 32.5 or

20mm extruded aluminium frame.

• An optional extra opposed blade damper is constructed of extruded aluminium blades can be

supplied on request.

• All models can have a powder coated white surface finish preceded by five stage preparation

process of cleaning, phosphatising and drying.

• Other colours are available on request.

• Grilles can also be supplied in natural anodised finish.

SA.CAT.Rev.31.03.2014

SUPPLY AIR GRILLES

Details

TYPE SD: Single Deflection Supply Air Grille

manufactured of extruded type 50S anodising grade aluminium with

individually adjustable horizontal louvers held in

place

by starlock washers and wire

Optional

Accessories OBD = Opposed Blade Damper

CF = Concealed Fixing

Frame Options 30mm Standard

20mm

50mm

Finish Options NA = Natural Anodised

EPC = Epoxy Powder Coating

Note: (1) Dimensions given are for opening size into which grille will fit (i.e Normal Duct Size)

(2) If code "OS" is entered under SPECIAL INSTRUCTIONS, then dimensions given are over

flange

SA.CAT.Rev.31.03.2014

PLASTIC DIFFUSERS & GRILLES

STREEMLINE RANGE

ADJUSTABLE BLADE DIFFUSER KITS

FEATURES

• The SL54 are designed to fit in a standard

commercial "T bar" ceiling grid

• Louvred biscuits can be adjusted to seven

optimum set points using the patented

locking system.

• Adjustable blade diffusers allows for airflow

adjustments after installation

• Each biscuit can be located to blow in any

one of four directions.

• Diffusers are quick and easy to install.

• Louvre blades remain flush with the ceiling at

all times with no ugly protrusions below the

ceiling.

• Aerofoil blade profile reduces air noise at the

grille and improves air diffusion.

• The louvre biscuits can be removed and

washed.

CONSTRUCTION

• The diffuser is manufactured from white ABS

plastic.

• Plastic neck adaptors are manufactured from

black ABS plastic.

• The diffuser clips are constructed from Acetal

plastic.

APPLICATIONS

• Ideal for commercial, refrigerated air

conditioning, heating and ventilation

applications

DIMENSIONS

SA.CAT.Rev.31.03.2014

PLASTIC DIFFUSERS & GRILLES

STREEMLINE RANGE

ADJUSTABLE BLADE DIFFUSER KITS

PERFORMANCE CHARACTERISTICS

SA.CAT.Rev.31.03.2014

PLASTIC DIFFUSERS & GRILLES

STREEMLINE RANGE

FIXED BLADE DIFFUSER KITS

FEATURES

• The SL54 are designed to fit in a standard

commercial "T bar" ceiling grid.

• Louvred biscuits are moulded in one piece

and the pitch of the blades is fixed.

• Diffusers are quick and easy to install.

• Louvre blades remain flush with the ceiling at

all times with no ugly protrusions below the

ceiling.

• Aerofoil blade profile reduces air noise at the

grille and improves air diffusion.

• Each biscuit can be located to blow in any

one of four directions.

• The louvre biscuits can be removed and

washed.

• Fixed blade Streemline diffusers are less

expensive than adjustable blade diffusers.

CONSTRUCTION

• The diffuser is manufactured from white ABS

plastic.

• Plastic neck adaptors are manufactured from

black ABS plastic.

• The diffuser clips are constructed from Acetal

plastic.

APPLICATIONS

• Ideal for commercial, refrigerated air

conditioning, heating and ventilation

applications

DIMENSIONS

SA.CAT.Rev.31.03.2014

PLASTIC DIFFUSERS & GRILLES

STREEMLINE FIXED BLADE DIFFUSER

PERFORMANCE CHARACTERISTICS

SA.CAT.Rev.31.03.2014

PLASTIC DIFFUSERS & GRILLES

STREEMLINE RANGE

EGGCRATE GRILLE KITS

FEATURES

• The SL54 are designed to fit in a standard

commercial "T bar" ceiling grid.

• Eggcrate biscuits are moulded in one piece.

• Grilles are quick and easy to install.

• The eggcrate biscuits can be removed and

washed.

• Fixed blade Streemline Eggcrate grilles are

less expensive than aluminium eggcrate

grilles and easier to remove and clean.

CONSTRUCTION

• The diffuser is manufactured from white ABS

plastic.

• Plastic neck adaptors are manufactured from

black ABS plastic.

• The diffuser clips are constructed from Acetal

plastic.

APPLICATIONS

• Ideal for commercial, refrigerated air

conditioning, heating and ventilation

applications

DIMENSIONS

SA.CAT.Rev.31.03.2014

PLASTIC DIFFUSERS & GRILLES

STREEMLINE RANGE

SSRV - STREEMLINE SECURITY RELIEF VENTS

FEATURES

• Rectangular grille with six removable

eggcrate cores and a vision proof barometric

damper behind the grille.

• The barometric damper will open if the

pressure on the room side of the grille is

greater than the pressure in the ceiling void.

• Supplied with a separate metal stop to

prevent the damper from blowing open.

• Fitted with rubber seals to prevent noise

when damper closes.

CONSTRUCTION

• These relief vents are constructed from white

plastic and have a black, fluted, plastic

barometric damper behind

PERFORMANCE

• Air flow through the grille will be determined

by the pressure in the room and room leakage.

Maximum air flow through a single grille should

not exceed 390 l/s if air noise through the grille

is to be avoided.

APPLICATIONS

• Security relief vents are designed to be

installed in the ceiling of areas which are

evaporative cooled. Installation of these grilles

provides a relief path for the evaporative

system and eliminates the need to open

windows and doors.

DIMENSIONS

SA.CAT.Rev.31.03.2014

PLASTIC DIFFUSERS & GRILLES

SILHOUETTE DIFFUSERS

FEATURES

• 360x360 Tee Bars are designed to drop in a

standard commercial “T bar” ceiling grid. It

can also be flush mounted in gyprock

ceilings.

• Available in 2 sizes:

• 280x280

• 360x360 (Tee Bar)

• Easy to clean removable cores

• Alternative cores are available to suit the

following blow configuration:

• 280x280: 4 and 3 way blow

• 360x360 (Tee Bar): 4 way blow

• Aesthetically pleasing louvre design

• Lightweight rigid construction

• 280x280 diffusers comes with spring loaded

clips for quick and easy installation

• 360x360 Tee Bar accepts all standard

Advantage Air 360x360 neck adaptors and

plastic cushion head adaptors.

• 280x280 silhouette diffuser accepts all

standard Advantage Air 280x280 neck

adaptors and plastic cushion head adaptors.

CONSTRUCTION

• Constructed from blended engineering

plastics

APPLICATIONS

• Ideal for commercial reverse cycle air

conditioning, heating and ventilation

applications

OPTIONAL EXTRAS

• Plastic neck adaptors

• Plastic cushion head adaptors

• Sheet metal cushion head adaptors

• Steel clips for Tee Bar diffusers

• Sheet metal OBD dampers

• Tabs on Tee Bar diffusers for installations to

imperial ceiling grids.

DIMENSIONS

SA.CAT.Rev.31.03.2014

PLASTIC DIFFUSERS & GRILLES

SILHOUETTE DIFFUSERS

PERFORMANCE CHART

SILHOUTTE DIFFUSERS

TEEBAR (360X360) & (280X280) DIFFUSER

SA.CAT.Rev.31.03.2014

PLASTIC DIFFUSERS & GRILLES

PLASTIC CUSHION HEAD

FEATURES

• Low cost

• Lightweight rigid construction

• Provides even airflow across entire diffuser

face

• Suitable for restricted ceiling voids

• Curved design allows easy ceiling installation

• Internal insulation reduces risk of

condensation and provides excellent acoustic

properties

• Integral hanging points

CONSTRUCTION

• Constructed from ABS blended engineering

plastics

APPLICATIONS

• Suitable for use on:

• Streemline diffusers

• Silhouette diffusers

• Spigot sizes available 200/250/300 diameter

OPTIONAL EXTRAS

• Can be internally insulated with a „closed cell‟

polyethylene adhesive material or a 25mm

(black scrim or perforated foil) fibreglass

• Manual or Motorised inlet damper

DIMENSIONS

SA.CAT.Rev.31.03.2014

PLASTIC DIFFUSERS & GRILLES

ROUND DIFFUSER

FEATURES

• Available in 4 different sizes:

• 150 dia

• 200 dia

• 250 dia

• 300 dia

• Stylish design

• Easily adjusted diffuser opening

• Low cost

• Lightweight rigid construction

• Easy to clean.

• Scratch resistant surface.

• Quiet.

• Snap action clips for fast and easy

installation.

• Tapered neck for easy duct connection

CONSTRUCTION

• These outlets are injection moulded from white ABS plastic and have integrated spring loaded clips

APPLICATIONS

• Ideal for commercial reverse cycle air-conditioning, heating and ventilation applications.

DIMENSIONS

GRILLE

SIZE

NOMINAL NECK

SIZE (mm)

FLANGE

SIZE (mm)

HEIGHT

(mm)

HOLE

DIAMETER

(mm)

150 DIA

145

268

231

200 DIA

200

328

100

284

250 DIA

250

390

102

356

300 DIA

300

436

102

398

SA.CAT.Rev.31.03.2014

PLASTIC DIFFUSERS & GRILLES

ROUND DIFFUESER PERFORMANCE DATA

200 DIA SUNLINE DIFFUSER

250 DIA SUNLINE DIFFUSER

SA.CAT.Rev.31.03.2014

PLASTIC DIFFUSERS & GRILLES

SWIVEL JET DIFFUSERS

FEATURES

• Unique swivel core allows the occupant to adjust the direction of airflow through 360o to suit furniture

layouts etc.

• Easy to clean.

• Quiet.

• Damper is easily adjusted from the face of the grille and will not blow closed.

• Snap action clips for fast installation.

• Tapered neck for easy duct connection

CONSTRUCTION

• These outlets are injection moulded from white A.B.S plastic and have integrated spring loaded

Clips

APPLICATIONS

• These outlets are ideal as heating, supply air ceiling diffusers.

• Can also be used for en-suite exhaust, bulkhead air conditioning / heating or as a reverse cycle jet

diffuser.

DIMENSIONS

MODEL

NO.

O/all

Neck

SJ15

262

100

148

SJ20

312

103

198

SA.CAT.Rev.31.03.2014

PLASTIC DIFFUSERS & GRILLES

SWIVEL JET DIFFUSERS - PERFORMANCE DATA

SA.CAT.Rev.31.03.2014

PLASTIC DIFFUSERS & GRILLES

BABY LINEAR GRILLE

FEATURES

• One piece construction of the diffuser eliminates unsightly joins.

• Attractive moulded diffuser is scratch resistant and will not corrode or deteriorate with age.

• Fast, easy installation.

• Significantly lower cost than aluminium diffusers.

• Will fit commercial ceiling grids.

• Easy to clean removable grille frame.

• Light weight ridged construction.

• Standard ceiling white.

• Paintable.

• Boots available in 200 DIA and 250 DIA connections.

CONSTRUCTION

• The diffuser is moulded from white ABS plastic.

• The boot/adaptor black ABS plastic.

• The frame can be supplied separately for bulkhead, wall and door installations.

• The boot clips are constructed from Acetal plastic.

APPLICATIONS

• Ideal for light commercial reverse cycle air conditioning systems.

• Suitable for ceiling, commercial T-Bar, bulkhead, and wall

• Suggested cut out 90mm x 570mm for boots. Grille only installations will require a smaller cut-out

hole for grille neck.

DIMENSIONS

SA.CAT.Rev.31.03.2014

PLASTIC DIFFUSERS & GRILLES

BABY LINEAR GRILLE PERFORMANCE

SA.CAT.Rev.31.03.2014

PLASTIC DIFFUSERS & GRILLES

LINEAR ELITE DIFFUSER

FEATURES

• Two 25mm slots provide high flow rates with low noise levels.

• One piece construction of the diffuser eliminates unsightly joins.

• Attractive moulded diffuser is scratch resistant and will not corrode or deteriorate with age.

• Fast, easy installation.

• Two deflectors per slot enables 180 degree throw pattern.

• Significantly lower cost than aluminium diffusers.

• Will fit both metric and imperial commercial ceiling grids.

CONSTRUCTION

• The diffuser is constructed from white ABS plastic.

• The boot, adaptor and deflectors are all constructed from black plastic.

• The internal insulation for the boot is moulded polystyrene.

• The boot is supplied with a side central hole for the propriety spigot.

APPLICATIONS

• Reverse cycle commercial air conditioning.

• Heating.

• Suggested cut out 118mm x 1175mm.

DIMENSIONS

SA.CAT.Rev.31.03.2014

PLASTIC DIFFUSERS & GRILLES

LINEAR ELITE DIFFUSER

PERFORMANCE CHARACTERISTICS

SA.CAT.Rev.31.03.2014

PLASTIC DIFFUSERS & GRILLES

AIRLINE DIFFUSER

Features

· Stylishly presented 4 slot Linear grille

· One piece face construction – no visible joins

· Scratch resistant, and will not corrode

· Suitable for airflow of up to 220 l/s

· 360 degree directable airflow

· Easy installation

Construction

· Grille – White ABS Plastic

· Boot – White ABS Plastic

Applications

· Commercial Reverse Cycle Air-conditioning systems

Dimensions

· Exact Neck Dimensions: 532mm x 196mm

· Height (including spigot, but not duct): 140mm

SA.CAT.Rev.31.03.2014

METAL RETURN AIR GRILLES

STOCK RANGE

RETURN AIR FILTER AND FRAME

MODEL

SIZE

NO.

BRAG595/595

595*595

BRAG1195/595

1195*595

CUSTOM RANGE

Type-RA

• These grilles feature light weight extruded aluminium with or without damper attached. The standard

grilles are available with fixed horizontal blades spaced at 21mm apart.

GENERAL SPECIFICATIONS

• Different spacing can be offered as a special request.

• The frame is constructed of 1.3mm thickness extruded aluminium with curved fins of extruded

aluminium of1.2 to 1.6mm thickness.

• The damper is constructed from extruded aluminium blades and frame.

• Grille can be furnished with powder coated white finish preceded by a five stage preparation

process of cleaning, phosphatising and drying.

• Other colours are available on request.

• Grilles can also be supplied as natural anodised.

• For outside weatherproof applications the Return Air Ribbed Blade (RARB) can be offered.

This type is particularly suited to grilles for console air conditioners

SA.CAT.Rev.31.03.2014

METAL RETURN AIR GRILLES

Details

TYPE RA (45deg. Deflection):

Return Air Grille manufactured of extruded type

anodising grade aluminium with fixed curved blade

profile giving low see through characteristics.

This grille may be mounted vertically or horizontally.

Optional

Accessories OBD = Opposed Blade Damper

CF = Concealed Fixing

FS = Rear Fixing Straps

Frame Options 30mm Standard

20mm

50mm

Finish Options NA = Natural Anodised

EPC = Epoxy Powder Coating

WS = Wet Spray Colour

Blade Spacing 13mm

19mm

21mm Standard

26mm

Note: (1) Dimensions given are for over flange size

(2) If 13mm, 19mm, 26mm Blade Spacing required, enter under SPECIAL INSTRUCTIONS

SA.CAT.Rev.31.03.2014

METAL RETURN AIR GRILLES

Type-RA

SELECTION DATA

SA.CAT.Rev.31.03.2014

PLASTIC RETURN AIR GRILLES

PURTECH RETURN AIR GRILLE

FEATURES

• Low cost.

• Scratch resistant.

• Removable core for easy cleaning.

• Complete with leak proof return air box.

• Two return air duct connections to ensure

even air distribution across grille and filter.

• Electrostatic filters provides 14% more

efficiency than standard filters.

• Accepts standard Advantage Air neck

adaptors for quick connection.

• Close tolerances ensure the grille does not

whistle.

• Attractive elongated eggcrate core reduces

pressure drop across core.

• Hidden mechanical latches ensures the core

will not drop.

• Plastic box construction reduces risk of

condensation and corrosion.

• Three sizes 1200x600, 900x400 and

750x550.

• 1200x600 model will drop into metric ceiling

T-bar system.

• Light weight ridged construction.

• Standard ceiling white.

• Paintable.

CONSTRUCTION

• Grille, box and adaptors are all blended

engineering plastics.

• Electrostatic filters are a special combination

of materials layered to provide the maximum

static charge to capture dust particles.

• Can be internally insulated using 6 mm

„closed cell polyethylene adhesive material

APPLICATIONS

• Ideal for small commercial ducted

• Can be used without filters for air transfer

and ventilation systems.

OPTIONAL EXTRAS

• Optional fresh air filter/connection.

• Optional dirty filter alarm to alert owner when

filter clean is overdue.

• Optional internal insulation for high humidity

climates.

• Optional double layer or 3 layer filter.

DIMENSIONS

SA.CAT.Rev.31.03.2014

PLASTIC RETURN AIR GRILLES

PURTECH RETURN AIR GRILLE

PERFORMANCE DATA

SA.CAT.Rev.31.03.2014

PLASTIC RETURN AIR GRILLES

SLIMLINE RETURN AIR GRILLE

FEATURES

• Low cost

• Front loading and removal of filter (optional)

• Light weight rigid plastic construction

• Scratch resistant

• Suitable for ceiling installations

• All plastic construction reduces risk of

condensation and corrosion.

CONSTRUCTION

• Grille frame is constructed from ABS blended

engineering plastics

• Filter frame and media are constructed from

Polypropylene plastic to provide maximum

static charge to capture dust particles

APPLICATIONS

• Ideal for small commercial ducted gas

heating and reverse cycle return air systems.

• Can be used without filters for air transfer

and ventilation systems

OPTIONAL EXTRAS

• Removable electrostatic filter

• Sheet metal installation frame

• Sheet metal box for ceiling return air

applications.

• Suitable for connection to standard

Advantage Air neck adaptors for ducting.

DIMENSIONS

SA.CAT.Rev.31.03.2014

PLASTIC RETURN AIR GRILLES

SLIMLINE PERFORMANCE CHART

SA.CAT.Rev.31.03.2014

DOOR GRILLES

TYPE-DG

STOCK RANGE

MODEL

NOMINAL

SIZE mm

DRG300

300*300

DRG4030

400*300

DRG400

400*400

CUSTOM RANGE

TYPE DG Door Grille complete with telescopic back

Frame manufactured of extruded Type 50S

anodising grade aluminium. These grilles

have fixed horizontal Chevron Louvres.

Dimensions W = Door Thickness

Fixing Options UD = Undrilled Standard

CF = Spring Clip can be supplied

if door thickness W is

ACCURATELY provided

(Door thicknesses vary

considerably

Note Also available without frames

(Picture for illustration purposes only)

TYPE DG DOOR GRILLE

Frame Options Standard Frame = 20mm

Telescopic Back Frame = 22mm

Finish Options NA = Natural Anodised

BEW = Baked Enamal White

EPC = Epoxy Powder Coating

Blade Spacing 13mm Standard

19mm

21mm

26mm

Note: (1) Dimensions given are for opening size into which grille will fit (i.e Normal Duct Size)

(2) If code "OS" is entered under SPECIAL INSTRUCTIONS, then dimensions given are over

flange.

(3) If 19, 21, 26mm Blade Spacing required, enter under SPECIAL INSTRUCTIONS.

SA.CAT.Rev.31.03.2014

DOOR GRILLES

TYPE-DG

SA.CAT.Rev.31.03.2014

DOOR GRILLES

TYPE-DG-DR

CUSTOM RANGE

TYPE DG Door Grille without telescopic back frame

manufactured of anodising grade aluminium.

These grilles have fixed horizontal Chevron

Louvres. For dark rooms and other areas

where light sensitivity is critical, Type DG-DR

is recommended.

TYPE DG-DR DOOR GRILLE

Frame Options = 22mm Standard

Finish Options NA = Natural Anodised

BEB = Baked Enamel Matt White

EPC = Epoxy Powder Coating Matt Black

Note: (1) Dimensions given are for opening size into which grille will fit

(2) Horizontal dimension is given first.

SA.CAT.Rev.31.03.2014

EGG CRATE GRILLES

STOCK RANGE

EGG CRATE FILTER FRAME

MODEL

SIZE

NO.

RAG595/595

595*595

RAG1195/595

1195*595

ALUMINIUM FRAMES & EGGCRATE

MODEL

SIZE

NO.

EC595

595*595 Eggcrate Grille

EC1195

1195*595 Eggcrate Grille

TF595/595

T-Frame 595*595

TF1195/595

T-Frame 1195*595

CUSTOM RANGE

TYPE-ECP

TYPE EC

Egg Crate Grille manufactured with frame of extruded Type 50S anodising grade aluminium

and high density styrene core.

Accessories OBD = Opposed Blade Damper

CF = Concealed Fixing

Dimensions D = ON / Normal Duct Size

ON - Over Neck Size

OS - Over Flange

Frame Options 30mm Standard

Finish Options A) FRAME NA = Natural Anodised Aluminium

BEW = Baked Enamel White

B) CORE = High Density Polystyrene

= Aluminium

Note: (1) Dimensions given are for 'OS' = Over Flange

SA.CAT.Rev.31.03.2014

EGG CRATE GRILLES

TYPE-ECA

TYPE ECA

Egg Crate Grille manufactured with frame of extruded Type 50S anodising grade aluminium

and the grid manufactured from 0,5mm aluminium sheet.

Accessories OBD = Opposed Blade Damper

CF = Concealed Fixing

Dimensions D = ON / Normal Duct Size

ON - Over Neck Size

OS - Over Flange

Frame Options 30mm Standard

Finish Options NA = Natural Anodised Aluminium

BEW = Baked Enamel White

EPC = Epoxy Powder Coating

(Picture for illustration purposes only)

Note: (1) Dimensions given are for 'OS' = Over Flange

SA.CAT.Rev.31.03.2014

EGG CRATE GRILLES

CORES

SPECIAL APPLICATIONS

EC & ECA CORES

EC & ECA Cores are available with a 10mm channel frame for "Drop In" Ceilings.

The channel frame fabricated of electro galvanised metal and painted.

Mitre cuts are not accurate as it is intended for channel to be hidden by ceiling "T".

Other Cores are also available on request

- Honeycomb (will required extended lead time to manufacture)

- 45° Angled Louvres

- Chrome Finish - both Matt or Gloss

SA.CAT.Rev.31.03.2014

EGG CRATE GRILLES

Details

SA.CAT.Rev.31.03.2014

WEATHER LOUVRES

Type – WPL

TYPE WLP Weather Louvre manufactured of extruded Type 50S

anodising grade aluminium. The fixed horizontal blades are held

in place by screws. Blades are spaced 35mm apart.

Standard Spacing = Top Blade fits flush with

frame. Lip of Bottom Blade

overlap frame.

Accessories WM = Wire Mesh

OBD = Opposed Blade Damper

NOTE: Adjustment from face

of Louvre is not advisable.

Holes

FS = Rear Fixing Straps

Dimensions ON = Normal Duct Size

Notes 1) Alternative Meshes available on request.

2) For Weather Louvres smaller than

450 x 300 we recommend the use of Type

RA with RARB Blade with19mm spacing.

TYPE WLP: WEATHER LOUVRE

Vermin Protection: - Plastic Bird mesh - Standard

- Galvanised wire mesh

Frame Options 50mm Standard

30mm

Finish Options NA = Natural Anodised

BEC = Baked Enamel Colour

EPC = Epoxy Powder Coating

(Picture for illustration purposes only)

Note: (1) Dimensions given are for opening size into which grille will fit

(2) If Code "OS" is entered under SPECIAL INSTRUCTIONS, then dimensions given are over

flange.

SA.CAT.Rev.31.03.2014

WEATHER LOUVRES

Type – WL

TYPE WL Weather Louvre manufactured of extruded Type 50S

anodising grade aluminium. Can be manufactured from 50 and

32.5mm frames. The fixed horizontal blades are held in place

by screws. Blades are spaced 50mm apart.

Standard Spacing = Top Blade fits flush with frame. Lip

of Bottom Blade overlap frame.

Accessories WM = Wire Mesh

OBD = Opposed Blade Damper

NOTE: Adjustment from face of Louvre

is not advisable.

FS = Rear Fixing Straps

Dimensions ON = Normal Duct Size

Notes 1) Alternative Meshes available on request.

2) For Weather Louvres smaller than 450 x 300 we

recommend the use of Type RA with RARB

Blade with19mm spacing.

TYPE WL: WEATHER LOUVRE

Vermin Protection: - Plastic Bird mesh - Standard

- Galvanised wire mesh

Finish Options NA = Natural Anodised

BEC = Baked Enamel Colour

EPC = Epoxy Powder Coating

Note: (1) Dimensions given are for ON size

(2) If Code "OS" is entered under SPECIAL INSTRUCTIONS, then dimensions given are over

flange

SA.CAT.Rev.31.03.2014

WEATHER LOUVRES

Type – WL

SA.CAT.Rev.31.03.2014

ALUMINIUM DIFFUSION SUNDRY

Transfer Grilles

MODEL

NOMINAL NECK

SIZE mm

TG3030

300*300 Transfer Grille

TG2020

200*200 Transfer Grille

SA.CAT.Rev.31.03.2014

INSULATION

DUCT BOARD INSULATION

TECHNICAL

GENERAL DESCRIPTION

Fibreglass Duct Board is a rigid high density

resin bonded fibreglass board faced externally

with a reinforced foil surface. The internal

surface can be supplied with either a resin

enriched surface or an on-line applied glass

fibre tissue. The boards are used to

manufacture a cost effective internal duct

system incorporating excellent thermal and

acoustic properties. The boards are lightweight

and safe. Duct Board meets all the elements

established for the requirements of a duct

material set by TIMA. These include:

a) Dimensional stability,

deformation and deflection.

b) Containment of the air being conveyed.

c) Exposure to damage, weather,

temperature extremes, flexibility or

other in service condition.

d) Support Duct Board is extremely versatile in

everyday use. It is broadly accepted and

specified for use in standard, thermal and

acoustical ducting requirement. Duct Board

meets the requirements of internationally

recognized standards making bodies such

as TIMA and SMACNA.

Duct Board Tools and Accessories

 Shiplap grooving tools (spare blades

available)

 Carrying case

 Peeler Knife

 Male-Female hand tools

 Round hole cutters

 Duct lay-out square

 Fasloop, wireloop banding tool for tie rod

 reinforcement

 Staple guns - manual or powered

 Pressure sensitive tape

 Washers and screws for all securing needs

 Turning vanes

 Simple to install spigots

 Duct supports

LABEL

SIZE

QTY

200X1 200 -un-lined

Each

2400X1 200X24-tissue-lined

Each

Ductboard Tape

55m

G.S.S Screws

100

G.S.P. Wsh. (Pin)

100

G.S.H. Wsh (Hole)

100

G.S.H Wsh.(Sqre.)

100

Staples

5000

Angle Flange 50X50X2400

Each

Ductboard Spigots

102mm

Each

127mm

Each

152mm

Each

180mm

Each

203mm

Each

229mm

Each

254mm

Each

305mm

Each

356mm

Each

406mm

Each

457mm

Each

508mm

Each

Staper-Manual(Loose Sup)

Each

Shiplap Kit-Complete Inc. 1,2,3,4,5

Tools, Construct. Man. Folding Square,

Round Hole Cutter, Cutsall (M/F) Tool,

PeelerKnife, Wire Loop Tool,Stapler 0

manual and carry case

Each

SA.CAT.Rev.31.03.2014

INSULATION

Insulation Data Sheet:

Description

Thickness

(mm)

Volumetric Mass

(kg/m )

Thermal

Conductivity

(W/mº C)

Temperature

Limits

Fire Rating

External Duct Wrap (FRK):

Duct Wrap 25

Duct Wrap 40

Duct Wrap 50

0.040(@35 C)

120 C

Class 1

Internal Acoustic Linings:

Sonic Liner 15

Sonic Liner 25

0.035(@20 C)

0.0378(@20 C)

120 C

Class 1

General Data Sheet:

Description

Thickness

(mm)

Volumetric Mass

(kg/m )

Thermal

Conductivity

(W/mº C)

Temperature

Limits

Fire Rating

Batt and Rolls:

MP 16 (Eroglite 16)

IM 24 (Eroglite 24)

IM 475 (Eroglite 475)

IM 64 (Eroglite 64)

IM 96 (Eroglite 96)

25 – 75

25 - 75

47.5

0.040(@24 C)

0.0378(@24 C)

0.033(@24 C)

0.0323(@24 C)

0.035 (@24 C)

250 C

450 C

250 C

Class 1

Example of how to calculate the noise attenuation

of internal ducting: What will the noise attenuation

of a 1m duct with a section of OAO x OAO m in a

frequency band of 260Hz, insulated with sonic liner be?

SA.CAT.Rev.31.03.2014

INSULATION

Technical

DUCT WRAP

DUCT WRAP THERMAL INSULATION BLANKET

DUCT WRAP is specifically designed as a thermal insulation blanket

manufactured from highly resistant, organic glass fibre bonded with a

resin. It is faced with an aluminium foil/skrim – reinforced kraft laminate

providing a resistant surface finish and an excellent vapour barrier. A 120

mm overlapping flange is provided on one side for a neater appearance

and adequate seal. DUCT WRAP is available in standard

APPLICATIONS

Duct Wrap is designed for application to rectangular and round heating,

ventilation and air conditioning duct systems where the operating

temperature is less than 120°C in commercial, industrial and residential

buildings.

BENEFITS

Energy conservation, lower operating costs, ease of installation, greater

CODE

DISCRIPTION

IDW02100

ISOVER - FRK

DUCTWRAP (FRK) 10M X 1.2M X 25MM

DUCTWRAP (FRK) 10M X 1.2M X 50MM

SONIC LINER

APPROVED ACOUSTIC BLANKET

SONIC LINER is an approved flexible fibreglass blanket faced with an

acoustically permeable black woven glass cloth on the air stream surface.

SONIC LINER is specifically designed as an acoustical and thermal liner

for sheet metal ducting and is fully approved by consulting engineers.

SONIC LINER is inert, ensuring long life; it is fire safe and erosion

resistant.

SONIC LINER is available in 15mm, 25mm and 50mm thickness

to meet your design requirements.

APPLICATIONS

Sonic Liner is specifically designed as an interior acoustical installation

liner for sheet metal ducts in heating, ventilation and air conditioning

systems operating at temperatures of up to 120°C and air velocities up to

20m/s.

BENEFITS

Designed and tested, sound absorption, convenience, fire safe, longer

erosion resistant and environmental control.

CODE

DISCRIPTION

ION025100

IONO50100

SONIC LINER 10M X 1.2M X 25MM

SONIC LINER 10M X 1.2M X 50MM

SA.CAT.Rev.31.03.2014

INSULATION

Technical

There are a variety of products available in both fibre glass and mineral wool (rockwool) suited to any

application. The products can be supplied with a combination of facing materials to meet different

specifications.

FIBRE GLASS

Specifically designed as thermal or acoustic blankets and batts, manufactured from highly resistant,

inorganic glass fibre or bonded with thermo-setting resin. They are made in board-form (type 1M) and

roll-form (Type IW). The products are available in different thicknesses and densities that permit

selection of a product to meet the majority of applications.

I.P. INSULWOOL (ROCKWOOL)

Insulwool is composed of a unique specialised mineral fibre; spun by a special process from molten

rock and slag having high silica and alumina values. They are bonded into various thicknesses and

densities with specifically formulated moisture resistant resins. The method of manufacture results in

a highly versatile, inexpensive, all purpose thermal and acoustic insulating product.

SIZE

GEN. INSUL.

1200 x 600 x 25

IM24 Eneremlite 24)

1200 x 600 x 40

IM24 Eneremlite 24)

1200 x 600 x 50

IM24 Eneremlite 24)

1200 x 600 x 75

IM24 Eneremlite 24)

1200 x 600 x 100

IM24 Eneremlite 24)

8000 x 1200 x 40

IM24 Eneremlite 24)

5000 x 1200 x 50

IM24 Eneremlite 24)

3000 x 1200 x 75

IM24 Eneremlite 24)

1200 x 600 x 25

IM475 (Eneremlite 475)

1200 x 600 x 40

IM475 (Eneremlite 475)

1200 x 600 x 50

IM475 (Eneremlite 475)

10000 x 1200 x 25

IM475 (Eneremlite 475)

8000 x 1200 x 40

IM475 (Eneremlite 475)

5000 x 1200 x 50

IM475 (Eneremlite 475)

1200 x 600 x 25

(Eneremlite 64)

1200 x 600 x 40

(Eneremlite 64)

1200 x 600 x 50

(Eneremlite 64)

1200 x 600 x 25

(Eneremlite 96)

10000 x 1200 x 40 )

(Eneremlite 16)

5000 x 1200 x 50

(Eneremlite 16)

10000 x 1200 x 25

(Eneremlite 18)

5000 x 1000 x 40

Insulfelt 60

5000 x 1000 x 50

Insulfelt 60

1000 x 500 x 40

Insulboard 60

1000 x 500 x 50

Insulboard 60

1000 x 500 x 75

Insulboard 60

1000 x 500 x 100

Insulboard 60

SA.CAT.Rev.31.03.2014

DAMPERS

OPPOSED BLADE DAMPER - Type – OBD

Determine the sound level which results from the combined effects of several sound sources

is not as difficult as it is confusing.

• The NY data for diffusers given contains an allowance for the sound absorbing properties of the

average room and its contents.

• This absorption is assumed to be 8 db with sound power level referenced to 10-12 Watts. (The

absorption is 18 db referenced to 10-13 Watts)?

• For relatively small spaces - about 76.2m2 or less floor area and ceiling height of 3.0m or less –

the following simplified method for estimating NC levels produced by a combination of supply

diffusers and return registers or grilles can be used:

1. Determine the difference in NC level between the supply outlets or return intakes having the

highest NC and the second highest NC level.

2. From Table 9 determine the number of decibels to be added to the NY level of the unit having

the highest NC level. This sum is the combined NC level generated by the two units.

3. If three units serve the space, determine the difference between the combined NC levels of the

first two units and the NC level of the third unit. Determine the NC addition as above, and add

this to the combined NC level of the first two units.

If the difference between NC levels of two units is 10 db or more, the sound generated by the

quieter unit will not affect the space NC.

EXAMPLE

Two supply diffusers having an NC level of 30 and a return grille having an NC level of 35 serve

a room. What is the combined NC level?

SOLUTION

The return has the highest NC level 35 db. The second highest is one of the diffusers at 30 db.

The difference between them is 5 db. From Table 6, the NC addition for a 5 db difference is

about one. Adding this to the higher NC gives a combined NC of 36.To take the second diffuser

into consideration, follow the same procedure as above. The NC calculated above is 36. The NC

of the diffuser is 30. The difference between them is 6. The NC addition for this difference is 1,

and the combined effect of the two diffusers and the return grille is NC 37.

SA.CAT.Rev.31.03.2014

OPPOSED BLADE DAMPER

TYPE OBD: Opposed Blade Damper manufactured

from extruded aluminium Blades.

Blades are held in place by spring wire

and starlock push on fix.

The OBD blades are linked and lever

or slot operated.

OBD suits all standard grilles and

diffusers.

BLADE OPTIONS: Standard as per sketch

FINISH OPTIONS: PR = Primed Black (optional)

MF = Mill Finish (standard)

BLADE SPACING: 25mm Standard

Note: (1) Dimensions given are for - To fit ON of mother grille

(2) If OBD to fit grille, indicate type of grille, outside neck size.

SA.CAT.Rev.31.03.2014

DAMPER HARDWARE

TECHNICAL

Heavy gauge plated steel quadrants with wing

Nuts for locking of damper. Frame marked to

Indicate exact position of damper

MODEL KS 12

Suitable for dampers up to 760mm.

Set consists of:

 13mm Quadrant

 KP 10 R Round end bearing

 KP 10 S Square end bearing

SA.CAT.Rev.31.03.2014

DAMPER HARDWARE

MODEL KS 385

These heavy gauge Plated Steel quadrants are designed with excellent

handle action as well as quick wing nut adjustment and locking of the

damper. The frame is marked to show the exact position of the damper.

For use on square or round ducts.

Suitable for dampers up to 500mm.

Set consists of:

 10mm Quadrant

 KP 7 Spring end bearing

 KP 9 S Square end bearing

SA.CAT.Rev.31.03.2014

DAMPER HARDWARE

MODEL KL 7 (R)

½” SHAFT LOC QUADRANT SETS - (FOR DAMPERS UP TO 30”)

“Shaft Loc” Quadrants are stamped of heavy gauge steel and clearly indicate the

position of the damper. The quadrant handle (available for either the ½” square or round

shafts) is unique in that it locks the shaft of the damper to it by means of a powerful

friction holding device strong enough to cut into the damper shaft eliminating damper

rattle. The shaft is easily locked with ½” open end wrench. Available for square or round

ducts.

1/2" SHAFT LOC QUADRANT SETS

ITEM#

MODEL

SHAFT DESCRIPTION

8063

KL7

1/2" Square loc quadrant

8064

KL7R

1/2" Round loc quadrant

PACKED 100 PER CARTON

KL7

KL7R

KL7R Section view

SA.CAT.Rev.31.03.2014

DAMPER HARDWARE

MODEL KS 145

These heavy gauge plated steel regulators are among the most popular on the market. They

minimize air leakage and reduce rattle. A wing nut locks the damper in position, yet permits

quick readjustment. The dial shows the damper position at a glance. The regulator mounts

easily on round or square ducts.

Suitable for dampers up to 250mm.

Set consists of:

 6mm Regulator

 KP 6 Spring end bearing

KP 8 S Square end bearing

SA.CAT.Rev.31.03.2014

ACCESSORIES

ACCESS DOORS

TECHNICAL

Access panels

The four sizes of access door provide a broad

range of "accessibility options" for fire

dampers, coils, filters and controls etc. The

large APO and API are designed for "torso

entry" whereas the AP2 and AP3 for two-

handed and single handed access

respectively. As the doors are deep formed

they are dimensionally uniform and eliminate

air leakage up to 200mm W.O. The design

enables fast installation and the plated sash

fasteners allow for speedy and simple access

CONSTRUCTION

FRAME 0,8mm Galvanised Steel

PANEL Outer panel 0.8mm Galvanised Steel

Inner panel 0.6mm Galvanised Steel

INSULATION 25mm Fibreglass

GASKET Heat welded PVC Extrusion

GASTENERS Sashtype Zinc Plated

MODEL

NOM.

SIZE

A x B

C x D

E x F

AP0

650 x 510

698 x

546

648 x

500

610 x

464

AP1

500 x 375

546 x

419

500 x

268

464 x

327

AP2

375 x 240

419 x

286

375 x

241

330 x

197

AP3

240 x 150

289 x

194

241 x

149

206 x

116

ADVANTAGE AIR insulated access doors

shall be supplied and installed for access to all

fire dampers etc. mounted within the ductwork.

Doors shall be deep drawn from prime quality

galvanised steel and shall incorporate a heat

welded tubular P.VC. gasket mechanically

fixed to eliminate air leakage up to 200mm

W.G Doors shall be removable and selected to

match duct sizes. The maximum size door

shall be installed to provide easiest access

SA.CAT.Rev.31.03.2014

AIRTURN RAIL

TECHNICAL

Air travelling throughout a duct is slowed up when it reaches a right angle turn. The "Slow-up" is

detrimental to the efficiency of the duct system, therefore air turning vane assemblies are used to

guide air evenly around such turns. With today's high labour costs, it is expensive for shops to

produce their own air turning assemblies. That's why Airturn rail is a major contribution to sheet metal

shops that require efficiency, yet inexpensive air turning vane assemblies.

FAST, LOW COST ASSEMBLY

With Airturn Rail, which is a pre-fabricated side rail, layout time is eliminated. Vanes can be sheared

from scrap metal without tab cutting, and quickly assembled to rails with only one blow of a ball pen-

hammer.

SA.CAT.Rev.31.03.2014

DUCTLOK FLANGING & FASTENERS

TECHNICAL

THE TOTAL DUCT FLANGE SYSTEM

FLEXIBLE DUCTING

DUCTLOK FLANGE

A roll formed galvanized

steel angle incorporating a

permanent non hardening

sealent, which guarantees a

dependable air tight

connection - eliminates the

need for post installation

sealing of the duct.

REINFORCEMENT BEAD

The unique DUCTLOK

REFORCEMENT bead makes

the flange stronger than

conventional flanges, thereby

reducing the necessity for

many different gauges of

flange profiles. DUCTLOK

produces only 2 sizes to cover

all applications. (DUCTLOK

JUNIOR - 25mm x O.8mm,

DUCTLOK SENIOR -

35mm x l.OOmm).

JOINING CLAMP

Ductlok Bolt-on flange

clamp for clamping of duct

flange joints.

CORNER PIECE

The Ductlok corner piece is

ribbed and edged flanged for

extra rigidity and features an

embossed dimple ensuring an

extra tight corner joint. The

bolt hole is suitable for

carriage type or normal bolt

corners, available in 2 sizes;

Junior and Senior.

GASKET TAPE

A Butyl rubber sealant strip

for insertion between

Ductlok flanges. Easily

installed. The tape is water,

heat and UV resistant.

HANGER BOLT

The Ductlok Hanger Bolt is a

new concept in reducing your

duct hanging costs. When fitted

to the Ductlok corner

piece in place of a normal or

carriage bolt, a length of

threaded duct hanging rod

can be fitted through the

hanger bolt, thus permitting

the duct hanger to be fixed to

the corner piece.

Assembly and installation data:

SA.CAT.Rev.31.03.2014

DUCTLOK FLANGING & FASTENERS

TECHNICAL

Assembly and installation data: (continued)

CODE

DUCTLOK

QTY

FLANGE - JNR

Junior flange

(25mm)

5 metre

FLANGE - SNR

Senior flange

5 metre

DLC JNR

Junior Corner

100

DLC SNR

Senior Corner

100

DLC

Ductlok Clamp

100

DUCTLOK

QTY

Gasketing (5mm)

metre

Eurostick Gasket (6mm)

metre

Ductlok Hanger Bolt

DUCTLOK

QTY

Bar Cleat (reinforced cleat)

2400

Drive Cleat

2400

S Cleat

2400

ADVANTAGE AIR CODE

DESCRIPTION

SH01

HAND STRAPPING 12MM X 1500MTR - BLACK

BP01

PLASTIC BUCKLES 12MM P/1000

CANCOLLAR

CANVAS COLLAR (DUCT CONNECTOR) 25MTR

QUICKTIE

Q-BAND 25MTR

QUICKCLIP

Q-CLIPS PACK OF 100

Advantage Air is able to offer, effective and economical insulation fastening systems to meet your

needs. These range from pins and washers, clip pins and hand held spotters, right through to

automatic rolling and bulk feed pinspotters. The PN spotter pin and washer are used with the

lightweight hand held LF2000 pin spotter - the industry standard . The CP clip pins with an integral

nail washer are used with the MFPT, PBFS and other automatic pinspotters. CP clip pins by Duro

Dyne have "lathe cut" points to ensure uniformly precise points and easy push through. Avoid

imitations and settle for the leader.

SA.CAT.Rev.31.03.2014

DVK VALVES

TECHNICAL

PLASTIC EXHAUST

PLASTIC AIR VALVE WITH CONNECTION BUSH.

PRODUCT PROPERTIES

* Diameter range 100, 125, 150 and 200 mm

* Manufactured from white polypropylene (RAL 9003) with a heat

resistance up to 100 degrees Celsius

* Suitable for rooms with a high air humidity (e.g. kitchen and bathroom)

* Easy to remove for cleaning purposes

* Air quantity can be adjusted continuously

DIMENSIONS (IN MILLIMETRES)

DVK

Ø100

Ø125

Ø150

Ø200

100

118

171

148

168

186

240

106

130

178

SA.CAT.Rev.31.03.2014

DVK VALVES

TECHNICAL

METAL EXHAUST

METAL EXHAUST AIR VALVE WITH FIXING COLLAR.

PRODUCT PROPERTIES

* Diameter range 100, 125, 150 and 200 mm

* Manufactured from powder coated steel

* Standard colour white (RAL 9010)

* Air quantity can be adjusted continuously

* The combination of fixing collar with bayonet catch and sealing tape provides an optimal sealing

* A fixing collar is included

DIMENSIONS (IN MILLIMETRES)

DVS

Ø 100

Ø 150

Ø 200

174

155

139

202

248

135

194

SA.CAT.Rev.31.03.2014

DVK VALVES

TECHNICAL

METAL EXHAUST

METAL SUPPLY AIR VALVE WITH FIXING COLLAR.

PRODUCT PROPERTIES

* Diameter range 100, 150 and 200 mm

* Manufactured from powder coated steel

* Standard colour white (RAL 9010)

* With adjustable, centric, rotating valve for regulation of the air quantity.

* Optimal sealing is achieved by the sealing ring

* A connection bush is included

(DIMENSIONS (IN MILLIMETRES)

DVS -

Ø 100

Ø 150

Ø 200

117

155

139

202

248

135

194

SA.CAT.Rev.31.03.2014

DVK VALVES

STOCK RANGE

ADVANTAGE AIR CODE

DESCRIPTION

DVS100

DISC VALVE STEEL 100MM DIA

DVS125

DISC VALVE STEEL 125MM DIA

DVS150

DISC VALVE STEEL 150MM DIA

DVS200

DISC VALVE STEEL 200MM DIA

VEF-10

DISC VALVE PLASTIC 100MM DIA

VEF-12

DISC VALVE PLASTIC 125MM DIA

VEF-16

DISC VALVE PLASTIC 150MM DIA

VEF-20

DISC VALVE PLASTIC 200MM DIA

SA.CAT.Rev.31.03.2014

SUNDRY ITEMS

PINS & WASHERS

ADVANTAGE AIR CODE

DESCRIPTION

WELD PINS

WELD PINS FTC12 P/5000

WELD P2

WELD PINS FTC12 P/5000

SPOTPIN

PN114 SPOTTER PINS FOR 1" DUCTLINER P/1000

EC2 WASHER

EC2 WASHERS P/1000

ADH SELF

SELF ADHESIVE PINS & WASHERS P/500

SPOTCLIP

PC1 SPOTTER CLIPS FOR PN PINS P/1000

SPOTPIN2

PN200 SPOTTER CLIPS FOR 2" DUCTLINER P/1000

SPOTPIN1-2

PN34 SPOTTER PINS FOR 1/2" DUCTLINER P/1000

CAM-LOK

CAMLOK P/EA

FILTER MEDIA

NL100150

FILTER MEDIA 100G SOLD PER METRE

ADHESIVES / SILICONE / SEALERS

B611 INSULATION

B611 - INSULATION ADHESIVE 20LTR

M622 - DUCT SEAL

M622 - DUCT SEALER 5LTR

280ML DUCT SEAL

M622 DUCT SEALER CARTRIDGE 280ML (12 per box)

TBE2 - BITUMEN

TBE2 - BITUMEN EMULSION 20LTR

B603 - POLYSTYRENE

B603 - POLYSYRENE ADHESIVE 5LTR

V435 ADHESIVE

V435 - SUPER GRADE CONTACT ADHESIVE 25LTR

M634J JAYCOSTIC

M634J - JAYCOSTIC 6MM X 60M

M77/4 - 280ML

280ML SILICONE GREY

HM73 - GLUE STICKS

HM73 - GLUE STICKS 10KG

VAP-01

GEN PURPOSE VAPOUR BARRIER 5LTR P2191

TAPE

PVC DUCT TAPE

SATF3001ADVA48

ALUMINIUM FOIL TAPE 48mm x 50m

VEN1599B

VENTURE TAPE

SC171VADVA48

GREY CLOTH TAPE 48mm x 25m

SILICONE

892317010

SILICONE - CLEAR

892317011

SILICONE - WHITE

CONDENSER BRACKETS

223AC450P

450 Powder Coated bracket

223AC450H

450 Galvanised bracket

223AC600P

600 Powder Coated bracket

223AC60H

600 Galvanised bracket

SA.CAT.Rev.31.03.2014

SUNDRY ITEMS

CASTELLATED COLLAR

ADVANTAGE AIR CODE

DESCRIPTION

CC10

100 DIA

CC15

150 DIA

CC20

200 DIA

CC25

250 DIA

CC30

300 DIA

CC35

350 DIA

CC40

400 DIA

CC45

450 DIA

CC50

500 DIA

CC55

550 DIA

DUCT JOINERS

DJ10

100 DIA

DJ15

150 DIA

DJ20

200 DIA

DJ25

250 DIA

DJ30

300 DIA

DJ35

350 DIA

DJ40

400 DIA

DJ45

450 DIA

DJ50

500 DIA

DJ55

550 DIA

CLAMPS

100HFGS60

100 DIA CLAMP

100HFGS92

150 DIA CLAMP

10HFGS112

175 DIA CLAMP

10HFGS128

200 DIA CLAMP

10HFGS160

250 DIA CLAMP

10HFGS188

300 DIA CLAMP

10HFGS224

350 DIA CLAMP

10HFGS252

400 DIA CLAMP

10HFGS284

450 DIA CLAMP

10HFGS316

500 DIA CLAMP

10HFGS340

550 DIA CLAMP

SA.CAT.Rev.31.03.2014

NOTES

ZTE THIS IS THE FRONT COVER PAGE Advantage Air SA Catalog Rev 20140408

Navigation menu

Versions of this User Manual:

Views

Navigation