ZTE MF920T LTE Ufi User Manual

ZTE Corporation LTE Ufi Users Manual

Users Manual

1 MF920T Quick Start Guide ZTE CORPORATION ZTE Plaza, Keji Road South, Shenzhen, China
2 Getting to Know Your Device Appearance The following figure is for your reference only. 1. Charging/micro-USB jack 2. Indicator light 3. Power key Press and hold for about 3 seconds to power on/off your device. 4. WPS key Press and hold for about 3 seconds to activate the WPS function. 5. SIM card slot and reset hole
3 Getting to Know Your Device Indicator lights Indicator Status Description Battery Red solid / blinking The battery is low. Please charge the battery. Green blinking The battery is being charged. Green solid The battery level is middle or high. Light off Your device is not being charged. Wi-Fi Blue solid Wi-Fi is active. Blue blinking WPS is active. Light off Wi-Fi is off. SMS Blue solid You have unread messages.Blue blinking You have new messages. Light off There is no unread message or new message.
4 Network Red Error status. Not registered to the mobile network, no SIM card inserted or no network service available. Green solid Registered to the 2G/3G mobile network. Green blinking Connected to the 2G/3G mobile network and data is being transferred. Blue solid Registered to the 4G LTE network. Blue blinking Connected to the 4G LTE network and data is being transferred.
5 Getting to Know Your Device Connection Scenarios The device allows multiple clients to surf on the Internet at the same time. The following figure is for your reference only. A SIM card can be used to access the Internet.
Installing1. Open the SI NOTE: Do not removethe device. 2. Install a SIM WARNINGYour device door any other nodevice, do not u3. Close the S6 g Your DevicM card cover. e the cover crudely, bM card to the SIM card! oes not support microon-standard SIM caruse those cards or aSIM card cover. ce because it is connec d slot. o-SIM cards, nano-Srds. To avoid damagny card holders. cted with IM cards ge to the
ConnectUsing Wi-F1. Power on yo2. Ensure thatenabled Wi- NOTE: Refurther details use a computeaddress autom3. Select the Connect. 4. Enter the Wi NOTE: RefSSID and Papassword. 5. Wait until tsuccessfullyUsing a US1. Connect a co2. Power on yidentifies nesoftware. 7 ting to Your Fi our device. t your computer orFi, and search for avfer to your Wi-Fi enaon how to search foer, you need to set yoatically. Wi-Fi name (SSID)i-Fi password if necefer to the chapter Gassword to get thhe client device is . SB Cable omputer to your deviyour device. The opew hardware, andDevice r other client devicvailable wireless netwabled client device maor wireless networksour computer to obta) of your device, aessary, and click OK.Getting to Know the default Wi-Fi SSconnected to youice with a USB cableperating system dete automatically instes have works. anual for . If you ain an IP and click he Wi-Fi SID and r device e. ects and talls the
NOTE: If the system ddouble-click thZTEMODEM to3. Wait until successfullyGetting tPassworYou can view SSID and passLoggingHotspot 1. Ensure thatclient device2. Launch the the address 3. Enter the usHotspot conf NOTE: The 8 oes not automaticallyhe device installatioo install the software.the computer is . to Know therd the label on the devsword. in to thConfigurati the connection bee is correct. Internet browser andbar. sername and passwofiguration page. e default username ay launch installation,n icon in My Com. connected to youre Wi-Fi SSIDvice to get the defahe 4G Mon Page tween your device d enter http://192.16ord to log in to the 4Gand password are ad you can mputer > r device D and ult Wi-Fi obile and the 68.0.1 in G Mobile dmin.
9 Changing the Wi-Fi SSID or Password 1. Log in to the 4G Mobile Hotspot configuration page. 2. Select Wi-Fi Settings. 3. Change the Network Name (SSID) or the Password in the SSID area. 4. Click Apply. Accessing the Internet After a client device is successfully connected to your device, you can access the Internet in Automatic or Manual mode. The default mode is Automatic. Mode Operation Automatic Your device is automatically connected to the Internet, and you can surf on the Internet through the client. Manual 1. Log in to the 4G Mobile Hotspot configuration page. 2. In My router section, select LTE (or other network type) Settings > Connection Mode > Manual, and then click Apply.
NOTE: To modify the pHotspot configu ConfigurThe following pProtocol in Win1. Right-click N2. Select Chan3. Right-click Properties. 4. Select InterProperties.5. Select ObtaDNS server 103. Click toand then click parameters of your deuration page. ring Your PCprocedure describes ndows 7 for your Wi-FNetwork and select Pnge adapter settingsWireless Network rnet Protocol Versiain an IP address raddress automatic return to the hom or .evice, log in to the 4GC how to configure theFi connection. Properties. s. k Connection andion 4 (TCP/IPv4), aautomatically andcally, and click OK.me page, G Mobile e Internet d select and click d Obtain
11 Warning and Notice To the Users • If inadequately shielded, some electronic devices, for example, the electronic system of vehicles, may be affected by the electromagnetic interference caused by the device. Consult the manufacturers of such devices before using the device if necessary. • Operating the device may interfere with medical instruments such as hearing aids and pacemakers. Always keep the device more than 20 centimeters away from such medical instruments when your device is powered on. Power off the device if necessary. Consult a physician or the manufacturers of medical instruments before using the device if necessary. • Be aware of the usage limitation when using the device at places such as oil warehouses or chemical factories, where there are explosive gases or explosive products being processed. Power off the device if necessary. • Do not use electronic transmission devices in aircrafts, at petrol stations or in hospitals. Observe and obey all warning signs, and power off the device in these conditions. • Do not touch the inner antenna area unless necessary. Otherwise the performance of the device may be affected. • Do not use the device in an enclosed environment or where heat dissipation is poor. Prolonged work in such space may cause excessive heat and raise ambient temperature, which may lead to automatic shutdown of the device for your safety. In the case of such event, cool the device in a well-ventilated place before turning on for normal use. • Keep the device out of the reach of small children. The device may cause an injury if used as a toy.
12 • When the device is operating, do not touch the metallic parts. Failing to do so may cause burns. • Use original accessories or accessories that are authorized. Using any unauthorized accessories may affect the performance of the device and violate the related national regulations about telecom terminals. • Avoid using the device near or inside metallic constructions or establishments that can emit electromagnetic waves, because signal reception may be affected. • The device is not waterproof. Keep the device dry and store it in a shady and cool place. • Do not use the device immediately after a sudden temperature change, because dew may be generated inside and outside the device. Do not use it until it becomes dry. • Handle the device carefully. Do not drop, bend or strike it. Otherwise the device may be damaged. • Only qualified personnel can dismantle and repair the device. • An operating temperature between -10°C and +60°C and humidity between 5% and 95% are recommended. Using Battery Do not change the built-in rechargeable battery in your device by yourself. The battery can only be changed by ZTE or ZTE authorized service provider. Limited Warranty This warranty does not apply to defects or errors in the product caused by: i. Reasonable abrasion. ii. End users’ failure to follow ZTE’s installation, operation or maintenance instructions or procedures. iii. End users’ mishandling, misuse, negligence, or improper
13 installation, disassembly, storage, servicing or operation of the product. iv. Modifications or repairs not provided by ZTE or a ZTE-certified individual. v. Power failures, surges, fire, flood, accidents, and actions of third parties or other events outside ZTE’s reasonable control. vi. Usage of third-party products or usage in conjunction with third-party products if such defects are due to the combined usage. vii. Any other cause beyond the range of normal usage intended for the product. End users have no right to reject or return the product, or receive a refund for the product from ZTE under the above-mentioned situations. This warranty is end users’ sole remedy and ZTE’s sole liability for defective or nonconforming items, and is in lieu of all other warranties, expressed, implied or statutory, including but not limited to the implied warranties of merchantability and fitness for a particular purpose, unless otherwise required under the mandatory provisions of the law. Limitation of Liability ZTE shall not be liable for any loss of profits or indirect, special, incidental or consequential damages resulting from or arising out of or in connection with using of this product, no matter whether or not ZTE had been advised, knew or should have known of the possibility of such damages, including, but not limited to lost profits, interruption of business, cost of capital, cost of substitute facilities or product, or any downtime cost. FCC Caution This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause
14 harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: -Reorient or relocate the receiving antenna. -Increase the separation between the equipment and receiver. -Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. -Consult the dealer or an experienced radio/TV technician for help. Any Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment RF Exposure This device was tested for typical body support operations. To comply with RF exposure requirements, a minimum separation distance of 1.0 cm must be maintained between the user’s body and the device, including the antenna. Third-party belt-clips, holsters, and similar accessories used by this device should not contain any metallic
15 components. Body accessories that do not meet these requirements may not comply with RF exposure requirements and should be avoided. Use only the supplied or an approved antenna. LEGAL INFORMATION Copyright © 2016 ZTE CORPORATION. All rights reserved. No part of this publication may be excerpted, reproduced, translated or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm, without the prior written permission of ZTE Corporation. The manual is published by ZTE Corporation. We reserve the right to make modifications on print errors or update specifications without prior notice. Version No.: R1.0 Edition Time: June 7, 2016
16 Troubleshooting Problem Recommended Action The connection between your device and a PC through a USB cable cannot be established.  Install the software, and run the installation program in the path of My Computer.  If the driver of your device is abnormal, reinstall the software. You need to uninstall the software first. The connection between your device and a client through Wi-Fi cannot be established.  Ensure that the Wi-Fi function is enabled.  Refresh the network list and select the correct SSID.  Check the IP address, and ensure that your client can automatically obtain an IP address.  Enter the correct network key (Wi-Fi password) when you connect the client to your device.
Troubles Problem The clienconnected tthe deviccannot accesthe Internet.The MobiWi-Fi configurationpage cannobe visited. Getting MYou can get he Sending a Visiting w 17shooting Recommendent to ce ss  Ensure tavailable. Change thwith good  Check thconnection Contact yconfirm yole ot  Enter thedefault add Use only your PC. Do not useMore Helpelp by: an email to mobile@www.ztedevice.comed Action that your SIM cahe location and find asignal. e settings of the n mode. your service provideour APN settings. e correct addressdress is http://192.16one network adape any proxy server.@zte.com.cn ard is a place WAN er and . The 68.0.1.pter in

Navigation menu