ZTE MF920T LTE Ufi User Manual

ZTE Corporation LTE Ufi Users Manual

Users Manual

Download: ZTE MF920T LTE Ufi User Manual
Mirror Download [FCC.gov]ZTE MF920T LTE Ufi User Manual
Document ID3192067
Application IDRzKHvG0PDpuh24uuYjtu5Q==
Document DescriptionUsers Manual
Short Term ConfidentialNo
Permanent ConfidentialNo
SupercedeNo
Document TypeUser Manual
Display FormatAdobe Acrobat PDF - pdf
Filesize12.55kB (156894 bits)
Date Submitted2016-11-10 00:00:00
Date Available2016-11-14 00:00:00
Creation Date2016-11-09 14:39:15
Producing SoftwareAcrobat Distiller 10.1.0 (Windows)
Document Lastmod2016-11-09 14:39:15
Document TitleMicrosoft Word - MF920T quick start guide v1.0_欧亚改频通用)
Document CreatorPScript5.dll Version 5.2.2
Document Author: ls

MF920T
Quick Start Guide
ZTE CORPORATION
ZTE Plaza, Keji Road South, Shenzhen, China
Getting to Know Your Device
Appearance
The following figure is for your reference only.
1. Charging/micro-USB jack
2. Indicator light
3. Power key
Press and hold for about 3 seconds to power on/off your
device.
4. WPS key
Press and hold for about 3 seconds to activate the WPS
function.
5. SIM card slot and reset hole
Getting to Know Your Device
Indicator lights
Indicator
Battery
Status
Description
Red solid /
The battery is low. Please
blinking
charge the battery.
Green
The battery is being
blinking
charged.
Green
The battery level is middle
solid
or high.
Light off
Your device is not being
charged.
Wi-Fi
Blue solid
Wi-Fi is active.
Blue
WPS is active.
blinking
SMS
Light off
Wi-Fi is off.
Blue solid
You have unread messages.
Blue
You have new messages.
blinking
Light off
There is no unread
message or new message.
Red
Error status. Not registered
to the mobile network, no
SIM card inserted or no
network service available.
Network
Green
Registered to the 2G/3G
solid
mobile network.
Green
Connected to the 2G/3G
blinking
mobile network and data is
Blue solid
Registered to the 4G LTE
being transferred.
network.
Blue
Connected to the 4G LTE
blinking
network and data is being
transferred.
Getting to Know Your Device
Connection Scenarios
The device allows multiple clients to surf on the Internet at the
same time. The following figure is for your reference only.
A SIM card can be used to access the Internet.
Installing
g Your Devic
ce
1. Open the SIM card cover.
NOTE:
e the cover crudely, because
it is conneccted with
Do not remove
the device.
M card to the SIM card
d slot.
2. Install a SIM
WARNING!
Your device do
oes not support micro
o-SIM cards, nano-SIM cards
or any other no
on-standard SIM carrds. To avoid damag
ge to the
device, do not use
u those cards or any card holders.
3. Close the SIM
S card cover.
Connectting to Your Device
Using Wi-F
Fi
1. Power on yo
our device.
2. Ensure thatt your computer orr other client devices have
enabled Wi-Fi, and search for avvailable wireless netw
works.
NOTE: Refer to your Wi-Fi ena
abled client device ma
anual for
or wireless networks.
further details on how to search fo
If you
use a compute
er, you need to set yo
our computer to obta
ain an IP
address automatically.
click
3. Select the Wi-Fi name (SSID)) of your device, and
Connect.
4. Enter the Wii-Fi password if nece
essary, and click OK.
NOTE: Reffer to the chapter Getting
to Know th
he Wi-Fi
SSID and Pa
assword to get the default Wi-Fi SS
SID and
password.
5. Wait until the client device is connected to your device
successfully.
Using a US
SB Cable
1. Connect a co
omputer to your deviice with a USB cable
e.
2. Power on your
device. The op
perating system dete
ects and
identifies ne
ew hardware, and automatically insttalls the
software.
NOTE:
If the system does not automaticallyy launch installation, you can
double-click th
he device installation icon in My Com
mputer >
ZTEMODEM to
o install the software..
3. Wait until the computer is connected to yourr device
successfully.
Getting to
t Know the
e Wi-Fi SSID
D and
Passworrd
You can view the label on the devvice to get the default Wi-Fi
SSID and passsword.
Logging
in
to
th
he
4G
Mobile
Hotspot Configuration Page
1. Ensure that the connection between your device and the
client device
e is correct.
2. Launch the Internet browser and
d enter http://192.16
68.0.1 in
the address bar.
3. Enter the ussername and passwo
ord to log in to the 4G
G Mobile
Hotspot conffiguration page.
NOTE: The
e default username and
a password are ad
dmin.
Changing
the
Wi-Fi
SSID
or
Password
1. Log in to the 4G Mobile Hotspot configuration page.
2. Select Wi-Fi Settings.
3. Change the Network Name (SSID) or the Password in the
SSID area.
4. Click Apply.
Accessing the Internet
After a client device is successfully connected to your device,
you can access the Internet in Automatic or Manual mode. The
default mode is Automatic.
Mode
Operation
Automatic
Your device is automatically connected to the
Internet, and you can surf on the Internet
through the client.
Manual
1. Log
in
to
the
4G
Mobile
Hotspot
configuration page.
2. In My router section, select LTE (or other
network type) Settings > Connection
Mode > Manual, and then click Apply.
3. Click
to return to the hom
me page,
and then click
or
NOTE:
To modify the parameters
of your de
evice, log in to the 4G
G Mobile
Hotspot configu
uration page.
Configurring Your PC
The following procedure
describes how to configure the
e Internet
Protocol in Win
ndows 7 for your Wi-F
Fi connection.
1. Right-click Network
and select Properties.
2. Select Chan
nge adapter settings
s.
3. Right-click Wireless Network
k Connection and
d select
Properties.
click
4. Select Interrnet Protocol Versiion 4 (TCP/IPv4), and
Properties.
5. Select Obta
ain an IP address automatically and
d Obtain
DNS serverr address automatic
cally, and click OK.
10
Warning and Notice
To the Users
•
•
•
•
•
•
•
If inadequately shielded, some electronic devices, for example, the
electronic system of vehicles, may be affected by the
electromagnetic interference caused by the device. Consult the
manufacturers of such devices before using the device if
necessary.
Operating the device may interfere with medical instruments such
as hearing aids and pacemakers. Always keep the device more
than 20 centimeters away from such medical instruments when
your device is powered on. Power off the device if necessary.
Consult a physician or the manufacturers of medical instruments
before using the device if necessary.
Be aware of the usage limitation when using the device at places
such as oil warehouses or chemical factories, where there are
explosive gases or explosive products being processed. Power off
the device if necessary.
Do not use electronic transmission devices in aircrafts, at petrol
stations or in hospitals. Observe and obey all warning signs, and
power off the device in these conditions.
Do not touch the inner antenna area unless necessary. Otherwise
the performance of the device may be affected.
Do not use the device in an enclosed environment or where heat
dissipation is poor. Prolonged work in such space may cause
excessive heat and raise ambient temperature, which may lead to
automatic shutdown of the device for your safety. In the case of
such event, cool the device in a well-ventilated place before turning
on for normal use.
Keep the device out of the reach of small children. The device may
cause an injury if used as a toy.
11
•
•
•
•
•
•
•
•
When the device is operating, do not touch the metallic parts.
Failing to do so may cause burns.
Use original accessories or accessories that are authorized. Using
any unauthorized accessories may affect the performance of the
device and violate the related national regulations about telecom
terminals.
Avoid using the device near or inside metallic constructions or
establishments that can emit electromagnetic waves, because
signal reception may be affected.
The device is not waterproof. Keep the device dry and store it in a
shady and cool place.
Do not use the device immediately after a sudden temperature
change, because dew may be generated inside and outside the
device. Do not use it until it becomes dry.
Handle the device carefully. Do not drop, bend or strike it.
Otherwise the device may be damaged.
Only qualified personnel can dismantle and repair the device.
An operating temperature between -10°C and +60°C and humidity
between 5% and 95% are recommended.
Using Battery
Do not change the built-in rechargeable battery in your device by
yourself. The battery can only be changed by ZTE or ZTE authorized
service provider.
Limited Warranty
This warranty does not apply to defects or errors in the product
caused by:
i. Reasonable abrasion.
ii. End users’ failure to follow ZTE’s installation, operation or
maintenance instructions or procedures.
iii. End users’ mishandling, misuse, negligence, or improper
12
installation, disassembly, storage, servicing or operation of the
product.
iv. Modifications or repairs not provided by ZTE or a ZTE-certified
individual.
v. Power failures, surges, fire, flood, accidents, and actions of third
parties or other events outside ZTE’s reasonable control.
vi. Usage of third-party products or usage in conjunction with
third-party products if such defects are due to the combined
usage.
vii. Any other cause beyond the range of normal usage intended for
the product.
End users have no right to reject or return the product, or receive a
refund for the product from ZTE under the above-mentioned
situations.
This warranty is end users’ sole remedy and ZTE’s sole liability for
defective or nonconforming items, and is in lieu of all other warranties,
expressed, implied or statutory, including but not limited to the implied
warranties of merchantability and fitness for a particular purpose,
unless otherwise required under the mandatory provisions of the law.
Limitation of Liability
ZTE shall not be liable for any loss of profits or indirect, special,
incidental or consequential damages resulting from or arising out of or
in connection with using of this product, no matter whether or not ZTE
had been advised, knew or should have known of the possibility of
such damages, including, but not limited to lost profits, interruption of
business, cost of capital, cost of substitute facilities or product, or any
downtime cost.
FCC Caution
This device complies with part 15 of the FCC Rules. Operation is
subject to the following two conditions: (1) This device may not cause
13
harmful interference, and (2) this device must accept any interference
received, including interference that may cause undesired operation.
Note: This equipment has been tested and found to comply with the
limits for a Class B digital device, pursuant to part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against
harmful interference in a residential installation. This equipment
generates uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause
harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If
this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or
more of the following measures:
-Reorient or relocate the receiving antenna.
-Increase the separation between the equipment and receiver.
-Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
-Consult the dealer or an experienced radio/TV technician for help.
Any Changes or modifications not expressly approved by the party
responsible for compliance could void the user's authority to operate
the equipment
RF Exposure
This device was tested for typical body support operations. To comply
with RF exposure requirements, a minimum separation distance of 1.0
cm must be maintained between the user’s body and the device,
including the antenna. Third-party belt-clips, holsters, and similar
accessories used by this device should not contain any metallic
14
components. Body accessories that do not meet these requirements
may not comply with RF exposure requirements and should be
avoided. Use only the supplied or an approved antenna.
LEGAL INFORMATION
Copyright © 2016 ZTE CORPORATION.
All rights reserved.
No part of this publication may be excerpted, reproduced, translated
or utilized in any form or by any means, electronic or mechanical,
including photocopying and microfilm, without the prior written
permission of ZTE Corporation.
The manual is published by ZTE Corporation. We reserve the right to
make modifications on print errors or update specifications without
prior notice.
Version No.: R1.0
Edition Time: June 7, 2016
15
Troubleshooting
Problem
Recommended Action
The

connection
Install the software, and run the
installation program in the path of My
between your
device and a
Computer.

If the driver of your device is
PC through a
abnormal, reinstall the software. You
USB
need to uninstall the software first.
cable
cannot
be
established.

The
connection
between your

device and a
client through
Wi-Fi
Refresh the network list and select
the correct SSID.

cannot
Check the IP address, and ensure
that your client can automatically
be
established.
Ensure that the Wi-Fi function is
enabled.
obtain an IP address.

Enter the correct network key (Wi-Fi
password) when you connect the
client to your device.
16
Troubles
shooting
Problem
The
Recommende
ed Action
clien
nt

connected to
the
devicce

cannot accesss
the Internet.
Ensure
that
your
SIM
ca
ard
is
available.
he location and find a place
Change th
with good signal.

Check the settings of the WAN
n mode.
connection

Contact your
service provide
er and
confirm yo
our APN settings.
The
Mobile

configuration
page
Enter the
e correct address. The
default add
dress is http://192.16
68.0.1.
Wi-Fi

canno
ot
be visited.
Use only one network adap
pter in
your PC.

e any proxy server.
Do not use
Getting More
Help
You can get he
elp by:

Sending an
a email to mobile@
@zte.com.cn

Visiting www.ztedevice.com
17

Source Exif Data:
File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.5
Linearized                      : Yes
Author                          : ls
Create Date                     : 2016:11:09 14:39:15+08:00
Modify Date                     : 2016:11:09 14:39:15+08:00
XMP Toolkit                     : Adobe XMP Core 5.2-c001 63.139439, 2010/09/27-13:37:26
Creator Tool                    : PScript5.dll Version 5.2.2
Format                          : application/pdf
Title                           : Microsoft Word - MF920T  quick start guide v1.0_欧亚改频通用)
Creator                         : ls
Producer                        : Acrobat Distiller 10.1.0 (Windows)
Document ID                     : uuid:437d9bab-4e4d-42a3-a24d-c2f47474d57b
Instance ID                     : uuid:ee71a56d-36be-4e5a-9212-e346cf5c51d6
Page Count                      : 17
EXIF Metadata provided by EXIF.tools
FCC ID Filing: SRQ-MF920T

Navigation menu