Contents
- 1. User Manual
- 2. Product Safety and Warranty Information
User Manual
| Download: |  |
| Mirror Download [FCC.gov] | |
| Document ID | 3426814 |
| Application ID | k96e8VlmbGVTdTocpcUjtg== |
| Document Description | User Manual |
| Short Term Confidential | No |
| Permanent Confidential | No |
| Supercede | No |
| Document Type | User Manual |
| Display Format | Adobe Acrobat PDF - pdf |
| Filesize | 45.79kB (572430 bits) |
| Date Submitted | 2017-06-14 00:00:00 |
| Date Available | 2017-12-13 00:00:00 |
| Creation Date | 2016-09-02 15:25:35 |
| Producing Software | GPL Ghostscript 9.10 |
| Document Lastmod | 2016-09-02 15:25:35 |
| Document Title | User manual |
| Document Creator | PDFCreator Version 1.7.3 |
| Document Author: | amqian |
Getting to Know Your OBD2 Device Appearance The following figure is for your reference only. Z6200 Quick Start Guide 1. Reset hole 2. micro-SIM card slot 3. Restart key 4. LED 1 5. LED 2 ZTE CORPORATION 6. OBD interface NO. 55, Hi-tech Road South, Shenzhen, P.R.China Postcode: 518057 Getting to Know Your OBD2 Device Installing the micro-SIM card Indicator lights 1. Use the tray eject tool to take out the card tray. 2. Put the micro-SIM card into the card tray and slip it into the Indicator Status Description card slot. WARNING! LED 1(Power) Green Powered by the internal To avoid damage to the phone, please do not use other kinds of blinking battery. SIM cards, and do not use a non-standard micro-SIM card cut Green Powered by the vehicle from a SIM card. You can get the standard micro-SIM card from solid battery. your service provider. Red Turn on but not register. 3. Close the micro-SIM card cover. Green Registered to the 4G Installing Your OBD2 Device solid network. Green Connected to the 4G LTE blinking network and data is being solid LED 2(Signal) transferred. NOTE: 1. Make sure your vehicle is parked outside in a safe location and the engine is turned off. 2. Find your Vehicle’s On-Board Diagnostics (OBD II) connector port. NOTES: The charging temperature should be lower than 60 . The OBD II port is usually located under the driver’s dash side of your car, often within 18 inches of the steering wheel (as 1 to 8 shown in the following picture). Connecting to Your OBD2 Device Turning on Your OBD2 Device Start your vehicle’s engine and let it run for at least 30 seconds. Using Your Wi-Fi Devices 1. Find your OBD2 device's network name in your Wi-Fi device's list of available wireless networks. 2. Select the Wi-Fi name (SSID) of your OBD2 device. If you’re having trouble locating your car’s OBD II port, 3. Input the password, and then tap Connect. reference your vehicle’s manual. 3. Insert your Device into the vehicle’s OBD II port. NOTE: Refer to the chapter Getting to Know the Wi-Fi Changing the Wi-Fi SSID and SSID and Password to get the default Wi-Fi SSID and Password password. Getting to Know the Wi-Fi SSID and 1. From the connected device, log in to the 4G Mobile Hotspot Password 2. Select Settings > Wi-Fi Settings. configuration page. 3. Change the Network Name (SSID) and Password. You can view the label on the device to get the default Wi-Fi 4. Click Apply. SSID and password. Setting up Allowed Devices Logging in to the 4G Mobile Enable Allowed Devices to prevent other device from connecting to the OBD2 device, only the MAC address listed in Hotspot Configuration Page the Allowed Devices Information section can access your OBD2 Use 4G Mobile Hotspot configuration on your Wi-Fi device to device. manage settings. 1. Ensure that the connection between your OBD2 device and the Wi-Fi device is correct. 2. Launch the Internet browser and enter http://192.168.0.1 in the address bar. 3. Enter the username and password to log in to the 4G Mobile Hotspot configuration page. NOTE: The default password is admin. 1. From the connected device, log in to the 4G Mobile Hotspot WAN Connection Mode > Manual, and configuration page. then click Apply. 2. Select Settings > Wi-Fi Settings. 4. Select Home and click 3. Set Allowed Devices Switch to On, and click Apply. to connect to the Internet. 4. Enter the Nickname and MAC Address. 5. Click Apply. NOTE: To prevent a device from reconnecting to your OBD2 device, click Remove next to the device. NOTE: To modify the parameters of your device, log in to the 4G Mobile Hotspot configuration page. Accessing the Internet After a client device is successfully connected to your device, you can access the Internet in Automatic or Manual mode. The default mode is Automatic. Mode Operation Automatic Your OBD2 device is automatically connected to the Internet, and you can surf on the Internet through the Wi-Fi device. Manual 1. Log in to the 4G Mobile Hotspot configuration page. 2. Select Home and click to disconnect from the Internet. 3. Select Settings > Network Settings > 10 LEGAL INFORMATION Getting More Help Copyright © 2016 ZTE CORPORATION. You can get help by: Sending an email to mobile@zte.com.cn All rights reserved. No part of this publication may be excerpted, reproduced, translated Visiting www.ztewelink.com or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm, without the prior written permission of ZTE Corporation. The manual is published by ZTE Corporation. We reserve the right to make modifications on print errors or update specifications without prior notice. Version No.: R1.0 Edition Time: July 1, 2016 Manual No.: 11 12
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.4 Linearized : No Page Count : 6 XMP Toolkit : XMP toolkit 2.9.1-13, framework 1.6 About : uuid:f6c14ecb-7339-11e6-0000-938d5379bc4f Producer : GPL Ghostscript 9.10 Keywords : () Modify Date : 2016:09:02 15:25:35+08:00 Create Date : 2016:09:02 15:25:35+08:00 Creator Tool : PDFCreator Version 1.7.3 Document ID : uuid:f6c14ecb-7339-11e6-0000-938d5379bc4f Format : application/pdf Title : User manual Creator : amqian Description : () Author : amqian Subject :EXIF Metadata provided by EXIF.tools